Search Documents

By Young C. Kim

In the past, underground coal mine planning has traditionally focused on the mine design n aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most of the underground coal mines within the U.S. With the enactment of the clean air act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the BTU contents of coal are of equal importance from boiler efficiency standpoint. Thus, the time has come when the coal mine planning must incorporate the coal quality control aspects as well as the traditional safety and efficiency aspects.

Jan 1, 1983

By C. Roos

Tradicionalmente en la industria minera, el flujo principal del proceso funcional para la evaluación de recursos y reservas procede de geólogos que elaboran el modelo geológico, de allí a los geólogos que hacen la estimación de los recursos (los modeladores) quienes estiman los grados, y a los ingenieros de mina que desarrollan el diseño de la mina y su calendario. La interfaz entre estas tres disciplinas no está siempre exenta de baches. Las presunciones hechas durante una etapa del proceso no siempre son comunicadas a los demás, a pesar que la mayoría de las empresas mineras tienen procedimientos y protocolos establecidos para promover la comunicación a lo largo de las distintas disciplinas. Estos procedimientos no siempre logran su propósito debido a una variedad de razones que incluyen restricciones de tiempo, no tener disponible a las personas apropiadas, o a una falta de entendimiento de lo que las otras disciplinas requieren, y el proceso de traspaso puede degenerar en el envío de archivos a la siguiente disciplina en el flujo de proceso. Este artículo se ocupa de la interfaz entre la estimación del recurso y las disciplinas de la ingeniería de minas y el esquema de algunas de las presunciones comunes hechas al generar un modelo del recurso y los riesgos que los ingenieros podrían correr al elevar los grados de corte, optimizar calendarios o realizar predicciones. Los casos de estudio presentados se centran en depósitos de oro a cielo abierto, pero los conceptos deben ser aplicables a toda la industria. Aquí también proveemos un resumen de preguntas clave y recomendaciones.

Jan 1, 2014

By Bryan A. Bartley

About 1,000 machines around the world are breaking rock and hard abrasive materials by a very economic, high intensity, autogenous process, but this method is largely ignored by the mining industry. This vertical shaft autogenous impact crusher has impact velocities around 70 m/s, which compare with those of Cascade and SAG mills of up to 10 m/s. The autogenous impact, breakage processes are all at higher intensity levels and the products reflect this difference. The topic of liberation is breifly considered. A series of tests with a laboratory scale machine are reported to illustrate a number of the characteristics of the process. This paper highlights topics for further evaluation and research.

Jan 1, 1992

By J. L. Thompson

The combustion of pulverized coal is a century-old practice. Many people have investigated coal dust and the residual fly ash particles that re-main after combustion. But the combustion process and fly ash formation mechanism are not under-stood. Working at our Maysville, Kentucky lime plant, the Dravo Lime Company Research team has collected samples of partially burned coal dust from the flame of a pulverized coal burner. Specimens were placed in a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). Microscopic examination of the particles, together with a large collection of micrographs of lime dust fused to fly ash particles, now make it possible to theorize as to how combustion advances through a piece of coal dust. Coal is a physical mixture of carbon-based compounds interspersed with bits of ash-forming materials, primarily alumina-silicate compounds. The alumina-silicate materials are commonly in angular nodules measuring 100 A to 700 A across their major dimension. It would appear that if the coal particle is in a well mixed gas stream, combustion starts at the surface and advances radially toward the particle center. With poor gas mixing, it is common that combustion moves from one end of a particle and advances on a broad front almost normal to some axis. In either case the combustion process and ash-forming mechanism are the same. As combustion occurs the carbon-based compounds oxidize in a highly exothermic reaction. Heat from the re-action melts the alumina-silicate nodules causing them to flow together and coalesce into an open sponge-like structure. As melting continues surface tension of the liquid and free surface energy causes the sponge-like structure to simplify into fewer, larger pores. Most likely the lighter molecular weight hydro-carbons burn before the heavier species. This means that as the melting ash structure is metamorphosing to a single large pore, there continues to be out-gasing throughout the structure due to combustion. Surface tension will form a spherical piece of fly ash if the ash material is liquid for a sufficient period of time. Out-gasing from combustion of the heavier hydro-carbons will provide internal gas pressure to keep the particle spherical until it freezes.

Jan 1, 1978

By Garland R. Dever

Extensive deposits of high-calcium limestone occur in the Upper Mississippian Warsaw and Ste. Genevieve Limestones in the region of the lower Cumberland, Tennessee, and Ohio Rivers in western Kentucky. Analyses of foot-by-foot samples from 20 quarries and cores in 8 counties show variations between the chemical composition of high-calcium deposits in the 2 formations. Knowledge of probable variations in composition should aid in prospecting for high-calcium stone for a specific use and in evaluating potential deposits. High-calcium strata in the Warsaw consist of bryozoan- and crinoid-rich bioclastic limestones, and in the Ste. Genevieve, predominantly oolitic limestones. Values used for comparison were obtained by averaging the foot-by-foot analyses of each high-calcium deposit, 10 in the Warsaw and 15 in the Ste. Genevieve. Average MgCO3 and Fe2O3 contents are generally lower in the Warsaw than in the Ste. Genevieve. Average SO2, S, and P contents are- generally higher in the Warsaw. No characteristic differences are apparent between the average CaCO3 and A1203 contents of the two formations. The higher S and P contents of the Warsaw are believed attributable to the predominance of biogenic material in these limestones. Within the Warsaw Limestone, higher average S and A1203 contents and lower average Fe2O3 contents were found in deposits in the northern half of the region. In the Ste. Genevieve, vertical variations in composition occur within individual high-calcium deposits containing oolitic and nonoolitic limestones. Lower average CaCO3 contents and higher average contents for the other constituents were found in the nonoolitic intervals.

Jan 1, 1972

By C. H. Smith

The present interest in beryllium seems to be the result of recent developments in the uses for the metal discovery of significant deposits of disseminated beryllium ores, and the development of chemical and physical processing techniques, for recovering the beryllium values contained in these ores. At the present time most of the new and potential uses for beryllium are in the research stage of development and are not consuming large quantities of the metal. However, they do point to an expanding market. Interesting new discoveries or extensions of previously known deposits have been reported during the past year from the Boomer Mine in Colorado, the Mesquite area of Nevada,, the Chemalloy pegmatites in Canada, the Brazilian and African pegmatite districts and from other areas, However, this paper will discuss only four of the beryllium deposits, which appear to be of special significance due to their; large reserves of ore and promise economic development. The new chemical and physical processing techniques are not discussed in detail, but it should be stressed that the development of an economical process to handle the pegmatitic and low-grade non-pegmatitic beryllium ores is of great importance to the development of the beryllium industry. Scientists in both government and industry are co-operating in this effort and it is expected that commercial processes will be developed in the near future.

Jan 1, 1962

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By William F. Ryan, Paul T. Gribbon

With the rise in construction claims in public works contracting over the years, the use of Dispute Review Boards (DRB’s) in underground construction contracts has become quite common. However, in order for the DRB process to be an effective tool, there must be complete trust and confidence in the Board members and their adopted procedures by both the owner and contractor. This can be difficult in an industry where Board members and contractors may be well known to each other, while an owner maybe involved in a large complex underground project only occasionally. Using case histories, this paper will discuss some recent experiences with the DRB process from an owner’s perspective.

Jan 1, 2003

By Philip-Mark Spanidis, Christos Roumpos, Francis Pavloudakis

This paper presents a quantitative research (QNR) methodology, collaboratively conducted with a group of mining experts, to assess the knowledge management (KM) landscape in the Greek mining industry. The methodology involves a framework for structured data collection using questionnaires, statistical analysis, discussion on critical methodological aspects, and interpretation of results focusing on key aspects of interest for designers of KM systems. The paper concludes by summarizing the methodology’s outcome and proposing perspectives for further research.

Aug 1, 2024

By L. M. Yokum

Tremendous strides have been made in front end loaders in the last fifteen years. Fifteen years ago a 2; cubic yard front end loader was the largest standard machine you could purchase. Today there are two commercially available 15 yard front end loaders and many 10 yard front end loaders. The estimated total worldwide market for all front end loaders over one cubic yard has increased to over 30,000 units yearly. The trend for front end loaders, in general, and for the mining market, in particular, is to larger and larger loaders. Today there are 18 cubic yard and a 24 cubic yard front end loader in prototype form. It is not inconceivable that within another fifteen years that there will be front end loaders in the 50 cubic yard class with design features quite different from today's. These larger loaders are being designed at the demand of the mining industry and the design criteria are being directed at this market area. The costs of these larger loaders will be greater per unit of capacity, and it is the intent of the various manufacturers that they will be more reliable, be easier to service, give greater availability, live longer, and cost less to maintain, than previous loaders. It is also the intent of the manufacturers to compete directly with the large mining shovel as the front end loaders become appropriately larger and more reliable. There has been some trend in this direction in the past with smaller shovels and loaders. In Figure No. 1 are data for U.S. production of front end loaders (5-6 cubic yard class and 10 cubic yard class) and U.S. production of cable operation, crawler mounted power shovels, draglines and cranes (1; to 5 cubic yard class) for the years 1965 and 1970. (Source: Bureau of Census, U.S. Department of Commerce.)

Jan 1, 1972

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By Leslie E. Apodaca

INTRODTUCTION The use of spiral concentrators for processing fine coal particles is an old idea that has recently gained acceptance in the 11.S. coal industry. It was not onti1 the Australian Minerals Industry developed a spiral concentrator specifically for separating coal from ash in the latter 1970's and early 1980's that spiral concentrators were seriously considered as viable equipment for processing fine coal. The Wright Coal Spiral was introduced in 1980, the Mineral Deposits Limited Mark 10 Coal Spiral was introduced in 1982, and the Vickers Wyong Coal Spiral was introduced in the latter part of 1984. Each spiral design was different and utilized constant profile troughs, constant pitch troughs, compound profile troughs, and various splitter arrangements. Mineral Deposits Limited has combined the best features of the compound profile trough and constant pitch trough with critically-placed splitters to develop the MDL LD4 spiral concentrator which is a truly efficient coal washing spiral. This spiral concentrator was introduced into the U.S. Coal Industry in 1987. Recently, Mineral Engineering Technology of the United Kingdom and Multotec of South Africa have introduced their own coal spiral designs. Spiral concentrators were first installed in fine coal processing circuits in the Australian, South African, and Canadian Coal Industries in the early 1980's and in the U.S. Coal Industry in 1985. SPIRAL CONCENTRATOR SEPARATION PROCESS The separation process that occurs within the spiral concentrator trough is very complex, as it is a combination of three gravity separation processes. When the coal slurry first enters the spiral trough, each coal and ash particle and the water is subjected to centrifugal forces. These forces cause the water, light coal particles, fine heavy ash particles, and medium middlings particles to the outer vertical portion of the spiral trough. The coarse ash particles and the coarse middling particles remain on the inside of the spiral trough. The center or transitional area of the trough contains a mixture of middlings particles and near-gravity material that is present in the slurry, as shown in Figure 1. At the same time the coal and ash particles are suhjected to centrifugal forces, the trough design (both profile and pitch) causes the particles to be subjected to flowing film and stratified bed separations. The combination of these three separations, whose efficiency is dictated by the spiral troogh design, will effect the separation of the lighter coal particles from the heavier ash and middlings particles. As the slurry flows down the spiral, the profile and pitch design of the trough will counteract the centrifugal forces on the fine, heavy ash particles and fine middlings particles and cause them to migrate from the vertical portion of the trough to the center or inner portion of the trough. At the same time, any heavy particles trapped in the transitional area of the trough will be forced to migrate to the inner edge of the trough and any coal particles will be forced to migrate to the outer edge of the trough. SPIRAL SPLI'TTEP ARRANGEMENT The critical placement of splitters along the inner edge of the trough for removal of the heavy ash particles as the slurry flows down the trough further enhances the separation of the coal particles. At the bottom of the spiral trough are product splitters arranged to make a final separation of the slurry stream into clean coal, middlings, and refuse products.

Jan 1, 1988

By Louis W. Riggs

The primary concern in dealing with contractual arrangements for construction is getting the work completed satisfactorily, in the shortest time, and for the least expense for the owner--while assuring that all other parties associated with the contract make a reasonable profit for their effort. In our complex construction climate of today, achieving all of these is usually not possible. Somewhere between the beginning of design and the completion of the work, disagreements and delays arise which can destroy the best of intentions. Assuming that all parties associated with the contract are acting honorably and professionally, the disagreements generally arise through inappropriate contract types or through flawed contract documents. These flaws can be either sins of omission or commission, but we must find a way to lessen, if not completely eliminate, their impact. Disagreements and delays are directly related to the extra cost which the owner and the other involved parties must suffer. Usually the attorneys are the only ones who come out on the positive side. Inappropriate or defective contract documents can be the result of inadequate time for preparation and review, laziness in not searching out the proper terms and language, insufficient recognition of the proper assignment of risks, or just ignorance as to what is right and what is wrong for the particular project. They can also result from a client, particularly a public agency, providing rigid general conditions and format requirements with which the engineer is not allowed to tamper. Arguments

Jan 1, 1979

By D. D. Harbuck

Previous studies at the U.S. Bureau of Hines have shown that only 70 to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the Bureau developed and researched the hypothesis that minor amounts of germanium and zinc silicate, both present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of silica gel formed increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1991

By Chas. E. Shumate

There is assembled here this morning in Chicago the heartland of America, what is undoubtedly the greatest concentration of Technical, Scientific and "CAN DO" knowledge ever assembled in America. The participation in this Conference by the representatives of so many nations is particularly impressive and is a further indication of the importance of the subject matter of this conference which you will be discussing in much detail during the next few days. Another impressive feature of this Conference is the participation of a large segment of the construction industry in whose hands fall the job of building what others design. Also strongly represented is the manufacturing industry whose capability is well known throughout the world. They have the resources to design, develop and manufacture the machines and specialized equipment needed to do any job which the world requires. You should not expect to gain any knowledge from my few remarks this morning as I am undoubtedly the least qualified individual in this room on the highly technical and scientific subjects you will be discussing during these next few days. However, I shall offer a few broad suggestions on subject matter which I trust may generate serious thought during your discussions.

Jan 1, 1997

By Robert C. Peddicord

Application of Quality Management philosophies and techniques commonly referred to as Managing for Continuous Improvement, Team Management , or Managing for Consistency is required in today's mining, manufacturing, and service industries in order to meet quality demands, beat competition, lower costs, optimize operations, effectively use personnel, improve morale, and enhance profitability. Most of these phiosophies and techniques are known to today's managers but either have fallen into disuse or were never allowed to surface in the corporate environment of the organization. Managers should review and adopt the philosophies and techniques of Quality Management and use them to revitalize their organizations and bring about a "paradigm" shift in the way we manage, thereby achieving the goals listed above.

Jan 1, 1991

By Eric Gilmore, Ron Tudor, Gregory E. Korbin, Bill McCormick, Brad Bush

INTRODUCTION Las Vegas has recently been termed the “Construction Capital of the Country”. It has also been acknowledged as the fastest growing city in the country for several years running. The rapid growth improves the economic picture of the region but it also imparts unusual demands on the area’s infrastructure. In 1994 the Southern Nevada Water Authority (SNWA)was working on a master plan to address the rapid growth. A long range analysis revealed the need for additional water treatment capacity and delivery systems. Short term projections showed that the current system would reach capacity in the summer of 1997 with the possibility of demand exceeding the supply. The River Mountains Tunnel #2 is part of a $150M scheme to quickly upgrade the system to meet the short term demand, improve the overall system operation and allow for a smooth transition into the larger additions being planned for the future. The SNWA selected Carollo/Black & Veatch (CBV) to provide detailed design and construction management for the upgrades. The River Mountains Contracts consisted of five separate contracts broken out separately to stream line a very aggressive (just 34 months) design and construction schedule. Necessary work included four miles of excavated and lined tunnel, connections from existing pipelines to and from the new tunnel including large diameter (to 3.66m(144 in)) valves, a 18 927cu m (5 million gal) regulating reservoir, a surge tank and a 170 343cu m (45 million gal) reservoir to add additional storage to the system. Notice to Proceed was given to Kajima Engineering and Construction (Kajima) on May22, 1995 for the construction of the River Mountains Tunnel #2. The design called for a tunnel to be driven 6070m (19 915ft) in rock and lined to a finished diameter of 3.71m (12.17ft).Excavation began on December 14, 1995 and holed through on April 30, 1996. Lining began on June 25, 1996 and a notice of Substantial Completion was issued on December 13,1996. This paper describes the measures taken to complete the tunnel in 18 months from Notice to Proceed to Substantial Completion. THE RIVER MOUNTAINS SITE The River Mountains are a low range of rugged mountains separating the Las Vegas Valley from its main supply of water, the Colorado River at Lake Mead. They are volcanic in origin and the harsh desert environment has left them as expanses of exposed bedrock rising 305m (1000ft) above the valley with little or no vegetation. An existing 3.05m (10ft)

Jan 1, 1997

By Raymond F. Mikesell

This paper evaluates the contributions of "third parties" to surplus capacity in the world metals industries in the 1980s. Special attention is given to the role of international development agencies, such as the World Bank, that have made project loans to state mining enterprises. The paper also reviews the contributions to surplus capacity of the International Monetary Fund and evaluates the large volume of credits from commercial banks to developing countries. Although the credits to Third World countries during the 1970s facilitated the expansion of mining capacity in those countries, no one source of financing can be held responsible for a significant portion of the expansion.

Jan 1, 1989

By Robert G. Beverly

INTRODUCTION Standards limiting the annual exposure of United States uranium miners to radon daughters were established in 1967 at 12 Working-Level-Months (WLM). The standard was reduced by a factor of three, to 4 WLM, in 1971. Currently, the standard is again being examined to determine if it should be changed. Since 1967, Union Carbide has calculated individual monthly exposures in company and contract-operated mines located on the Colorado Plateau. Although it has been possible, by extensive ventilation control measures and accurate routine sampling, to meet the current exposure standard, there are many miners whose exposures closely approach the 4 WLM standard for any given year. However, it was noted that for miners who work for any extended period of years the [average] exposure was much less than the standard. The primary purpose of this paper is to show that, in effect, any annual exposure standard to radon daughters results in a long-term exposure considerably below that standard. Further, most miners, due to their job assignments and/or employment habits, only receive a small fraction of the standard. HISTORY OF EXPOSURE STANDARDS Prior to 1967, radiation protection in uranium mines was fundamentally based on a radon daughter concentration guide. In 1960, the American Standards Association published mine and mill radiation protection standards (ASA-1960). The Colorado Department of Mines, in 1961, adoped a standard which followed the ASA Standard and provided that if concentrations exceeded 10 Working Levels (WL), the area was to be shut down until corrective action was taken; if between 3 and 10 WL, corrective action was to be initiated; between 1 and 3, additional samples were to be taken and individual exposures evaluated; and if below 1 WL, conditions were considered to be controlled. In 1967, the U.S. Department of Labor issued the first exposure standard which called originally for limiting annual exposures to 3.6 WLM but which was later changed to 12 WLM. The complicated regulatory developments leading to this standard have been described elsewhere (Beverly-1969, Rock & Walker-1970). Effective July 1, 1971, this exposure standard was lowered to 4 WLM per year, which is the current standard. Over the past year, there has been speculation about the potential risk to uranium miners working at the present standard. A recent NIOSH Study Group Report (NIOSH-1980) concluded: "There is also strong evidence that a substantial risk extends to and below 120 WLM of exposure." The 120 WLM corresponds to a miner working in uranium mines for 30 years, a rare occurrence, at an exposure rate of 4 WLM per year, an even rarer occurrence. On the other hand, the General Accounting Office, in a recent Report to the Congress (GAO-1981), was very critical of reports by NIOSH on general low-level radiation risks. The GAO recognized that”...important questions remain unanswered about the cancer risks of low-level ionizing radiation exposure;" and recommended that Congress enact legislation giving statutory authority to an interagency committee to coordinate Federal research on health effects of ionizing radiation exposure. The International Commission on Radiation Protection at its March, 1980 meeting recommended limiting the inhalation of radon daughters to 0.02 J per year, equivalent to 0.4 WL, which on an annual basis would be 4.8 WLM and noted it is common to reduce this figure by 20% for allowance in the case of uranium miners for external and/or dust exposure(Sowby-1980). This is essentially equal to the present standard of 4 WLM. As earlier uranium miner exposure studies are reevaluated, and as new studies are conducted, it is important that the relationship between regulatory standards and the resulting actual exposures be recognized. UNION CARBIDE URANIUM MINING EXPERIENCE Union Carbide started mining Colorado Plateau uranium-vanadium ores in the late 1920s for the contained vanadium values. In the early 1950s, the Atomic Energy Commission contracted Union Carbide to produce uranium at mills located in Uravan and Rifle, Colorado. The company now has over fifty years of mining experience in the area. Some mines are operated as company mines and others are operated by private mining companies under a contractual arrangement. Ventilation, sampling, and exposure calculations are carried out the same in contract mines as in company-operated mines. Data presented in this report do not differentiate between company or contract employees and include all employees who worked underground any portion of a year in Union Carbide mines from 1967 through 1980. At the peak of uranium mining activities in 1970, there were 577 miners employed at year end (285 company employees and 292 contract) and 52 mines in operation (8 company-operated and 44 contract mines). Contract mines varied from two-man operations up to 15 employees. Company mines were generally the larger operations and employed from 20 to 100 miners.

Jan 1, 1981

By W. H. Langer

Natural aggregate is the number one non-energy mineral resource in terms of value and volume and is a necessary commodity for sustainable communities. While aggregate is a non-renewable resource, supplies are nearly inexhaustible on a global scale. Natural aggregates have characteristics that differentiate them from most other mineral commodities: a high number of potential extraction sites, a high volume to value ratio, significantly different set of potential environmental impacts, and regional importance combined with a narrow economic transportation radius. Because of these and other differences, resource management policies for aggregates should differ from ?general? mineral resource policies, even though the end goal is the same for both ? ensuring sustainable resource management. To achieve the goals of sustainable aggregate management each stakeholder ? government, industry, the public, and non-governmental organizations ? will need to accept certain responsibilities, one of the most important of which is to become informed about natural resource issues. Sustainability is about making trade offs among competing objectives, and people disagree about the appropriate balance among the goals of economic prosperity, social equity, and environmental health. One of the primary purposes of mineral indicators is to provide information to decision makers and the public so as to ensure that the public debate about policy choices is grounded in fact. We identify the unique aspects of aggregate resource management and introduce the concepts of sustainable mineral resource management. We then present mineral indicator sets for aggregate resources from Italy, the United Kingdom, and Slovenia to demonstrate that effective mineral indicators should be specific to the resource in question and the public values and objectives.

Jan 1, 2003