Search Documents

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

By B. Salopek

The greatest part of crushed stone, gravel and sand production is extracted through open pit operations, whereas gravel and sand are also partially extracted from riverbeds. Its obvious that such a mining activity provokes some changes in the configuration and environmental characteristics of the region, in the temporary or permament disapperance of vegetable or animal species and in the creation of noise, dust and waste water. However, the above-mentioned mining operations shouldn not have only negative effects on the landscape and land potential, but they can discover and predetermine the potential of the exploited areas for various communal purposes after exploitation (eg. sports and recreation centers, campsites, resorts, fish-farms, etc.). In this paper, the production of construction aggregates in plants located in the vicinity of Zagreb, the capital of Croatia is presented. The advantages and disadvantages of aggregates? production in urban areas in the spirit of sustainable development are discussed.

Jan 1, 2003

By F. M. Doyle, S. Duyvesteyn, K. Sreenivasarao

Toxic metals entering surface or ground water from sources such as metal finishing shop spills and abandoned mines can pose a significant threat to public health and the environment. Ion flotation and similar foam separation techniques show great promise for treating dilute, metal-contaminated solutions, and could also be used to treat effluents from many minerals and metallurgical processing operations prior to discharge. In ion flotation, an appropriate collector is added to the solution to form hydrophobic complexes with the metal ions. These metal-bearing species are then removed by flotation, usually with trace addition of a frother to stabilize the foam. In an effort to better understand the underlying scientific and engineering principles that determine the performance of ion flotation, the removal of Cu(II), Pb(II), Cd(II), Cr(II) and Cr(VI) has been studied using laboratory scale flotation columns in batch mode. The effects of the superficial air velocity, solution and froth height, nature of the collector, collector: metal-ion ratio, ionic strength and several frothers at low concentrations on the flotation kinetics are reported. Finally, results are presented on methods that might allow regeneration of collector and recovery of by-product metal from the foam product.

Jan 1, 1995

By K. Adam

Uncontrolled disposal of pyrite wastes and concentrates comprise a major source of acid drainage in active and abandoned sulphide mines. In this paper, the state?of-the-art mitigation measures implemented for the final reclamation and closure of a pyrite concentrate stockpile at Platia Karra, Stratoni mines, Greece, are presented.

Jan 1, 2002

The effect of the chemical composition of pulverized bituminous coal particles on their physical transformation during the initial stages of combustion has been investigated. The results suggested that cenosphere formation does not require extensive thermal decomposition of the coal particles. The vitrinites in the bituminous coal softened earlier and developed larger cenospheres than the othe macerals. The coal particles swell to a higher extent during combustion than in pyrolysis; however, the cenospheres formed in the former process experienced a higher extent of fragmentation. The development of microporosity occurred predominantly after the resolidification of the swelled char particles. The type of macerals originally in the coal did not significantly affect the microporosity of the chars. Conversely, the morphology and anisotropy of the chars were strongly dependent on the maceral composition of the coal.

Jan 1, 1986

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By Charles S. Phillips

Kaiser Aluminum and Chemical Corp. (KACC) had been discharging spent bauxite-generally referred to as red mud-into the Mississippi River for almost 20 years when, in 1972, it agreed to store the waste solids on land. KACC decided to utilize a DREW system (decantation, drainage, and evaporation of water) where the spent bauxite is deposited in a large drying bed, surrounded by a 9-m-high levee. At the bottom of the bed, corrugated, perforated plastic pipe is encased in filter sand. The company built one DREW bed at Gramercy, LA, in 1973 and a second at Baton Rouge in 1974 using draglines, tractors, and rubber-tired scrapers. When a third bed was needed in 1977, the estimated construction cost using draglines was judged too high and KACC personnel began searching for a better, less expensive method for constructing the levee. A bucket-wheel excavator and conveyor system was selected and has proved to be less costly than more traditional earth-moving systems.

Jan 7, 1980

By A. Benchekroun

The phosphate mining industry is confronted everywhere in the world with financial difficulties and low prices which prohibit further investments and development of new mines even in regions with a comparative cost advantage (North America/ North Africa/ and Middle East). But old mines are being progressively exhausted/ and if no replacement mines come on stream in the near future/ we may soon find ourselves (around the year 2000) with a global annual production capacity of 160 million tonnes of marketable phosphate rock instead of the capacity of 200 million tonnes existing today. Unless prices improve/ phosphate rock/ a non-renewable resource and a vital commodity to world agriculture/ may turn to be in short supply to world fertilizer industry. Whatever the extent of recovery of fertilizer demand/ the expected decline of the production capacity during the 1990 I s is bound to cause the disappearance by the year 2000 of the important surplus characterizing today the supply/demand balance.

Jan 1, 1995

By David J. Kruse

Accurate field measurements are essential when validating a conveyor design. They are fundamental in determining a conveyor's behavior, its long-term maintenance requirements, and the life expectancy/ condition of the installed equipment. Field measurements are also invaluable in forensic engineering, particularly when vital equipment has failed This paper will discuss a wide variety of data acquisition equipment, field measurement techniques and accuracies achieved State-of-the-art, custom designed monitoring equipment, as well as, ''08-the-shely instruments and sensors, will be discussed.

Jan 1, 2004

By M. Woodie

INTRODUCTION Information such as application review to choose the proper style of vibrating screen, parameters that determine the proper size of vibrating screen, engineering design information that governors proper screen design, review of topics that govern proper isolation from structural steel and other topics that dictate proper screen selection for applications will be presented in this paper. Topics like process and application information review to choose the style of screen and how material size and type influences proper type of screen selection (multi-slope, incline, horizontal, linear incline or dewatering) will also be discussed. Parameters will be reviewed that help size the screen for the application. The total amount of surface area to size a screen is critical to the overall success of a screen installation. Once proper style of screen is determined there is an engineering process that is required to design the screen to operate correctly in the environment it will be used. Finite Element Analysis, Dynamic Modeling, Field Vibration Analysis and other engineering tools will be reviewed to best implement a successful vibrating screen installation. TYPES OF SCREENS Multi-Slope Multi-Slope vibrating screens are used where sizing large amounts of tonnage on surface areas that would be smaller than conventional screening where roughly 6” (150mm) minus material is required to be sized. Occasionally larger particle sizes can be screened on the Multi-Slope machine but the effectiveness of the machine can be diminished with larger particle sizes and larger than 4” (100mm) screen opening. The most common and effective size range of screening with these machines is 2” (50mm) minus material. The Multi-Slope screen is used where particle size is not extremely important. Mineral processing, hard rock mining and industries where exact material size is not critical are best suited for this equipment. Because the aggregates industry requires very specific material sizes, the Multi-Slope screen is not suited for most aggregate screen applications. The key to the success of a Multi-Slope screen is proper material presentation at the feed end of the screen. This allows for the material to stratify quickly and disperse the fines through the screen quickly with a relatively thin bed depth at the feed end which allows the undersize material through the screen quickly.

Jan 1, 2019

By L. A. Arrington-Webb

Forty-four states produced clay products during 1994 for a total value of $1.6 billion. This was a 3% increase in total tonnage and a 7% increase in value from 1993. Kaolin Domestic production of kaolin during 1994 was estimated to be 9.3 Mt (10.2 million st), according to the US Bureau of Mines (USBM). Georgia remained the leading producer with 7.5 Mt (8.2 million st), followed by South Carolina with 535 kt (589,000 st). Kaolin used as a paper coating or filler pigment accounted for 51% of domestic consumption. Other uses included grogs (14%), fiberglass (5%) and plastics (4%). A reclassification by an Alabama producer of fire clay to kaolin accounts for the introduction of kaolin used in grogs. This also accounts for the apparent decrease in the use of kaolin in paper from 60% in 1993. However, the actual amount of kaolin used in paper was the same.

Jan 1, 1995

By J. S. Whatley

The properties, origin and industrial uses of kaolin clay are briefly reviewed. The general waterwashed beneficiation process is described. Yost aspects of filtration and solids-liquid separation as practiced in the kaolin industry are mentioned along with devices that are currently in the developmental stage. The paper focuses heavily on the well known art of rotary vacuum filtration, including general construction and operating details. Devices under investigation that might be used to mechanically or electrically dewater clay slurries to higher cake solids levels than can be achieved with rotary vacuum filters are described briefly.

Jan 1, 1986

By M. Charles Gilbert

Basement rocks in southern Oklahoma are divided into two groups. One group is the Lower Cambrian Wichita Igneous Province, a diverse igneous suite that crops out in the western Arbuckle Mountains and in the Wichita Mountains. These largely bimodal igneous rocks were emplaced in an intracratonic-rift environment. The other group, the older, is a set of Precambrian rocks of the Eastern Arbuckle Province, yielding ages between 1,350 and 1,400 Ma, exposed in the core of the eastern Arbuckle Mountains. These are deeply eroded mesozonal granitic rocks and associated granitic gneisses cut by numerous dikes ranging in composition from diabase to rhyolite. The southern Oklahoma igneous rocks have long been utilized mostly as dimension and crushed stone. Most of the early quarries were in granite of various red hues for monuments and facing stones. Large crushed-stone quarries are now exploiting both granite and rhyolite, which is used chiefly as aggregate and railroad ballast. The exposed basement rocks in Oklahoma represent an underdeveloped and accessible resource.

Jan 1, 1999

By Alfred Jr. Petrick, William A. Vogely

INTRODUCTION The scope of mineral finance extends beyond the economic aspects of property evaluation to all of those activities involving acquisition and utilization of funds with an objective to optimize the value of the firm. It must, therefore, en- compass consideration of the overall financial goals of the firm, decisions involving external versus internal growth and domestic versus foreign investments, management of working cap- ital, efforts to minimize the cost of capital, and decisions with regards to the instruments of long- term debt and equity financing. The scope of this section is limited to considerations of special interest to the mineral or petroleum engineer, which include the following aspects of mineral finance: (1) The technical aspects of mineral or coal property or oil and gas reservoir evaluation which provide the basis for estimation and forecasting of revenues and costs. (2) Estimation and forecasting of costs and prices in a inflationary economic environment. (3) Calculation of cash flows which model .. , the investment in minerals, coal or oil, and gas. Such models require assumptions as to the timing of cash flows, escalation of capital and operating costs, base prices, and escalation, the tax regime, royalties, division of profits and the economic aspects of loans. (4) The role of discount rate in the economic analysis of an investment which requires consideration of the opportunity costs of the firm, cost of capital, risk premiums. (5) Risk analysis including application of the concepts of conditional net present value, expected value, and risk preference as well as the application of the techniques of sensitivity and simulation. (6) Selection of application criteria for in- vestment decision making. (7) Capital structure with particular reference to the effect of debt financing. (8) Consideration of sources of funds utilized by the minerals industries. (9) Long-range planning including portfolio analysis. This section is limited to principles, methodologies, and trends in mineral investment, finance, and long-range planning in the United States with a perspective from the year 1984. Consideration of the key concepts is supplemented by case examples of investment risk analysis and financial structure. Important factors affecting mineral investment evaluation during the 1980s include volatile metals prices, cost inflation, and the introduction of techniques requiring the computer and its capacity for improved technical and economic analysis into the hands of those who know most about the industry. The personal computer is replacing the calculator on the desk of the individual analyst and is rapidly becoming a required tool for the study of engineering and economics. Examples of change brought about by the micro-computer include greatly improved techniques of cost estimation, wider application of the computer for project analysis, computer graphics, reserve estimation, geostatistical analysis, mine design and other techniques that capitalize on the ability of the computer to handle

Jan 1, 1985

By L. J. Prosser, A. T. Iannacchione

From 1991 through 1995, 44 miners out of a total workforce of less than 2,000 were fatally injured in the stone industry. Of these, 12 occurred at underground mining operations with nine deaths resulting from roof or rib falls. A safer environment can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground-control strategies. Roof and rib conditions were observed and assessed in 33 underground stone mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania and West Virginia (Fig. 1). Hazard assessment indicated that the ground failures that occurred under moderate to substantial overburden, i.e., >30 m (100 ft), were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine-layout decisions

Jan 1, 1999

By W. F. Hahnert, P. A. S. Ralston

In off-line training of a rule-based controller, the significant measure of successful training is the quality of control provided by the generated rule set. In an adaptive or on-line control environment, performance is also measured by the ability to accurately maintain a satisfactory rule set, but within constraints on speed and/or resource availability. Very small population genetic algorithms, or microGAs, have been proposed as a means of capitalizing on the hill climbing characteristics of faster local optimization techniques while requiring less memory and retaining much of the robustness of traditional, larger population genetic search. A traditional genetic algorithm and a similar microGA are developed and applied to two control problems. The performance of these algorithms is analyzed with respect to (1) the quality of the rules learned, (2) the rate at which learning occurs, and (3) the memory resources required during learning.

Jan 1, 1993

By Stephen Leslie

A multimedia tutorial illustrating the geology and mineral resources of Gulf Coast salt domes has been developed as a pilot project for a course on Texas geology and resources at the University of Texas at Austin. The principal objective of the tutorial is to educate students with limited background in geological sciences about a major local geologic feature and its geologic and economic significance. The content of the tutorial represents materials generally covered in 4 hours of lecture and laboratory instruction. These materials are presented using a flattened hierarchy of topics, each accessible from a central menu, including salt-dome history, salt tectonics, anhydrite and calcite cap rocks, mineral resources, and geophysical character. Information concerning salt-dome geology is communicated using interactive software; sound and animation are used throughout to reinforce key concepts. Visual aspects include field views, hand specimens, and photomicrographs that were digitized from slides. Illustrations were created using a graphics program or scanned from available archives. Each visual element has an accompanying explanation, which in many cases is linked to other parts of the tutorial. Navigation is accomplished using hyper-links or a set of unobtrusive buttons. The program includes a glossary of the major minerals associated with salt domes available as a pull-down menu and digitized video footage of the Gulf of Mexico sea floor to illustrate the active environment of the formation of the salt-dome cap rock. In addition, a group of interactive questions is presented to assess the level of mastery. Technical aspects were accomplished using a Power Macintosh ? 7100AV and a variety of commercial software. Actual linking of information was done with Authorware? 3.0 Educational, an icon-based, multimedia authoring program. Graphic illustration was done with Adobe Illustrator ?; image processing was accomplished using Adobe Photoshop?; video was cap¬tured, edited, and compressed using Adobe Premiere ?. The interactive nature of the project was designed with regard to future means of dissemination, especially on the World Wide Web. This tutorial serves as a template to build additional modules covering the entire course. A modular approach to the coding of the project and extensive self-documentation should ensure the viabil¬ity of the project by allowing other workers with moder¬ate computer skills to complete other lessons within the curriculum framework.

Jan 1, 1999

By Boris V. Vlasenko, Vadim P. Potapov, Gennady I. Gritsko

In this paper we consider the elements of an information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated sys tem is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of changes in geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By D. C. Wilder

Deformations during heating and cooling of three drifts in granitic rock were influenced by the presence of faults and shear zones. Thermal deformations were significantly larger in sheared and faulted zones than where the rock was jointed. but neither sheared nor faulted. Furthermore. thermal deformations in faulted or sheared rock were not significantly recovered during subsequent cooling thus a permament deformation remained. This inelastic response is in contrast with elastic behavior identified in unfaulted and unsheared rock segments. A companion paper (Butkovich and Patrick, 1986a) indicates that deformations in un- sheared or unfaulted rock were effectively modeled as an elastic response. We conclude that permanent deformations occurred in fractures with crushed minerals and fracture filling or gouge materials. Potential mechanisms for this permanent deformation are asperity re-adjustments during thermal deformations. micro-shearing, asperity crushing and crushing of the secondary fracture filling minerals. Additionally, modulus differences in sheared or faulted rock as compared to more intact rock would result in greater deformations in response to the same thermal loads.

Jan 1, 1986

By D. Piper, J. Noble, M. Richardson, J. Wojcik, L. W. Cope

L. Cope Welcome. I am pleased to see so many people interested enough to stay until this last session of the last afternoon of the convention. Of the people on the panel here, everyone has done everything in placer mining, but we have tried to sectionalize it with each one of us taking a particular portion. Any one of us could probably answer any question. I am very pleased to see some well experienced people in the audience. To start the discussion, Joe, can you give us a brief comparison of pit and drill sampling? J. Wojcik They both have their place. If you expect your deposit is something that is going to have widespread fairly uniform grades, then the pits may be the way to go. If you are going to have something you have to trace for several miles down the river valley, you can't do it with pits and do a proper sampling job. C. McLain Joe, the end result of all of this is to go ahead and mine it if it is a deposit. Do you try to relate your drilling results to something in mining itself against the recovery, because the drilling in different types of ground will give you different kinds of recoveries, and mining in the end is what you are going to do? Do you try to relate this to your mining method?

Jan 1, 1992