Search Documents

By Bahne C. Cornilsen, X. Shan, David H. Carlson, John H. Johnson

The air in three U.S. underground coal mines has been sampled. The data developed show the relative importance of the various pollutants and quantify the need for control. Total respirable particulate matter (TRPM) was found to be the critical pollutant (the one requiring the most dilution for control). TRPM is considered to be "respirable coal dust" by procedures approved for sampling in U.S. underground coal mines. However, this "respirable coal dust" also includes diesel particulate matter (DPM) and particulate from other sources. While "respirable coal dust" was the critical pollutant, Raman spectroscopic analysis showed that more than half of this "respirable coal dust" was DPM. The DPM in the samples ranged from 22 to 152% of the 2 mg/m3 limit for respirable coal dust. Thus DPM was the critical pollutant using the 2 mg/m3 respirable coal dust limit. SO2 gas produced by the combustion of diesel fuel containing sulfur was the second-most critical pollutant. Characteristic curve slope (CCS) values were calculated to determine the quantitites of the various pollutants generated per unit of diesel haulage activity. Mine 1 had the highest TRPM CCS values with 29 mg/m3/%C02 for the Ramcar and 57 mg/m3/%C02 for the Haulageway location. The highest coal particulate CCS measured was 30 mg/m3/%CO2 and the highest diesel particulate CCS measured was 27 mg/m3/ %C02. Both of these high values were measured in the Mine 1 haulageway location. Calculations were made to determine the controlling CO2 concentrations (CCC) at which all other measured pollutants would be within their limits. These CCC values, which, for the mines sampled, were based on TRPM, varied from a low of about 0.07% for the Mine 1 haulageway location, to a high of about 0.15% for the Mine 2 Ramcar and haulageway locations. Weekly average CO2 concentrations measured in these mines ranged from 0.09 to 0.11 % for the Ramcar, from 0.05 to 0.09% for the haulageway, and from 0.08 to 0.11 % for the return. The concentrations of TRPM ranged from 1 and 2 mg/m3 in mine areas frequented by personnel, and to greater than 4 mg/m3 in returns where personnel are not exposed.

Jan 1, 1991

By B. A. Firth

Australia is the largest exporter of coking and thermal coal to the international market. This market has required that the coal being presented to the customer has a particular level and consistency of quality. In this context, the Australian industry has developed coal preparation practices that allow this criteria to be met while maximising the recovery of coal from the resource. This has required on- going developments in both coarse and fine coal cleaning technology over the past 30 years. Coal flotation has undergone a number of developments with regard to maximising recovery from the overall plant circuit. This includes innovative flotation circuits (split feed), methods of enhancing the use of reagents and control of pH. During the 1990s, there have been major changes in flotation as practised in Australian coal preparation plants. Columns have become the preferred technology for both greenfield developments and plant upgrades. This paper will outline the above developments with a number of plant examples and the reasoning that has driven the change. The ongoing research that is being carried out on new cells to optimise the overall fine coal circuit will also be discussed.

Jan 1, 1999

By Vytas Svalbonas

Sophisticated computer analysis methods such as finite elements, finite differences, and numerical integration have become tools in the mineral processing industry for design of large mill shells. While use of such methods allows the analyst-designer to take new freedoms with his designed structure, there are also pitfalls and dangers which must be recognized for the proper use of such sophisticated tools. One of the worst of these is treating any computer answers as "gospel truth". The present paper discusses the knowledge required by the analyst-designer for proper use of computer analysis, as well as explaining to the layman how to identify questionable areas in such structural analyses.

Jan 1, 1979

By Albert J. Kritscher

The Similkameen Copper Project located near Princeton, British Columbia, is operated by the Similkameen Mining Company Limited, a wholly-owned subsidiary of Newmont Mining Company. The orebodies for this project are located on both sides of the Similkameen River for which the project is named. The project involves the processing of an average of 15,000 STPD of andesitic ore, mineralized largely with Chalcopyrite, at an overall plant availability rating of 90 percent. Project life is nominally 15 years. Design for the plant and its ancillary facilities was undertaken by Bechtel Corporation with procurement and construction management by Canadian Bechtel Limited. Construction began in June 1970 and first ore was introduced into process in March 1972. This paper concerns itself only with the project tailing system. The processing plant is located on a bench of glacial stream gravels which overlooks the river canyon. This site represented the only relatively flat area of sufficient size to accomodate processing facilities near to the ore- bodies. Reference is made to Figs. 1 and 2 showing the relationship of project features in plan and profile.

Jan 1, 1973

By C. Ceccarini, I. Salvadori, G. Oggiano

GENERAL BACKGROUND The first mention of the presence of bauxite in the mesozoic series of north-west Sardinia (fig. 1) is owed to Oosterbaan, a Dutch geologist, who carried out a geological survey of the area in the ninetten thirties. A more detailed study of the mesozoic series was attempted in the fifties by Pecorini and other, who concentrated particularly upon the stratigraphy of the bauxitic horizons, through examination of the various outcrops. In the sixties a pining company, Monte Amiata S.p.A., turned its attention to a section of the deposit outcropping near Olmedo and, considering it to be of some promise, carried out prospecting works consisting essentially of various trenches, some bore holes, a few adit and a. layout plan for the preparation and execution of trial exploitation. The results, although positive, did not convince the company's shareholders to continue the exploration. This report, which is intended as a new contribution to knowledge of the Sardinian bauxite deposit, takes into account the information acquired not only from a drilling prospection begun in 1979 in connection with the SOMIT-PROGEMISA joint venture, but also the results of structural studies and numerous chemical, mineralogical and

Jan 1, 1984

By J. D. Mc Beth

The Carlin Gold Mining Company, a wholly owned subsidiary of Newmont Mining Corporation has been successfully operating an open pit gold mine and cyanide mill for approximately the past ten years. It is a unique operation in that about 20 percent of the mill feed is a carbonaceous ore refractory to cyanidation that must undergo a pretreatment stage developed for, and by, Carlin. The mine and plant are located in the Tuscarora mountain range is north-eastern Nevada near the towns of Carlin and Elko. Claims were staked at the minesite in 1961 and 1962. A drilling program was initiated late in 1962 and after drilling a total of 250,000 feet of rotary drill holes an estimated 9,300,000 tons of ore at a grade of 0.32 ounces of gold per ton was delineated.

Jan 1, 1975

By Rasik H. Raythatha

Calcium carbonate is perhaps the most widely used mineral in the world. With total consumption of all calcium carbonate exceeding over 25 million tom per year, within this class of filler, a relatively smaller segment of precipitated calcium carbonates (PCC) is often misunderstood as a commodity product and bundled in the same category as ground calcium carbonate. However, each material has a distinctly digerent role and characteristics. Precipitated calcium carbonates are used to influence specific performance in a specific application whereas ground calcium carbonate is used primarily to reduce cost in many applications. In this paper, attempts are made to demonstrate the role of nano-fine-PCC in improving shear-thinning characteristics of common and specialized sealants and automotive underbody coating and how such "nano-particle" cal- cium carbonate properties can be exploited to process PVC plastics while reducing overall cost. We also review the role of precipitated calcium carbonate as "nano" material and why it must be viewed as a specialty additive.

Jan 1, 2003

By Kadri Dagdelen, M. Waqar Asad

Cement production involves the processing of raw materials that contain - Si02, A1203, Fe203, CaO, MgO, LOI (loss of ignition), S03, K20, Na2O, Ti02, P2055 and Cl- to produce the synthetic mineral mixture called "clinker". The use of other additives - sandstone, flyash, iron ore, and clay - is also mandatory in order to achieve the optimum blending requirements of cement. However, the use of these additives needs to be minimized due to their significantly higher costs ($/Ton). This paper presents a mixed integer programming (MIP)-based optimum quarry scheduling algorithm, which is used to generate quarry plans, satisfying geometric and production capacity constraints while providing minimum cost/optimum blend of raw materials mix to a cement plant. The benefits of this new methodology are demonstrated on a case study.

Jan 1, 2002

By St. E. Deák

This paper focuses on maintenance of underground salt air curative quality using environmental friendly solutions. Possible ways to preserve its curative properties, in relation with the admissible salt air quality parameters, are analyzed. In situ investigations regarding microbiological impregnation in walls and the air inside the Romanian salt sanatorium were initiated. The results of a pilot project, which is in progress at Praid salt mine, are presented. After the end of the investigation at this site, investigations will continue in other Romanian salt mines, such as Slanic Prahova, Targu Ocna and Cacica.

Jan 1, 2006

By Nikhil C. Trivedi, Robert W. Hagemeyer

Despite the apparently unflattering term filler, this group of industrial materials has become an essential component of many industrial products with varying degrees of sophistication. Mineral fillers are, by definition, inert materials included in a composition for some useful purpose. Included in this broad category are asbestos, barite, bentonite, natural calcium carbonates (limestone), clays, diatomite, feldspar, micas, silica, talc, and other industrial minerals. Also included in this category are synthetic mineral- derived materials such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. Mineral fillers are included in compounds to accomplish a variety of final results. Inclusion of fillers modifies physical characteristics such as hardness, brittleness, impact strength, compressive strength, surface texture, fire resistance, softening point, and electrical conductivity. Depending upon the performance characteristics of the particular filler used and the quantity of the usage (i.e., percentage added), these materials can enhance the physical and optical properties, price-performance, and appearance of the finished products. These enhancements in properties of the finished compounds are the result of properties of the fillers including chemical activity, purity, hardness, particle size, particle shape, particle size distribution, surface structure, color, density, and refractive index. This chapter will review the general usage of fillers, the rationale for their use, trends, and economic factors influencing those trends. Major using industries will be examined in detail with extensive discussion of major fillers used in those industries. The reader is referred to the appropriate commodity chapter for specific information on deposits and processing for industrial minerals. All of these same filler materials have additional significant uses based on their chemical composition or other characteristics. Cross-references for these will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 5th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and synthetic) and their more important end uses.

Jan 1, 1994

By Samer Sadek, Phoebe Cheng, Changmo Kwon, Myat Ohn

BART Facilities Standards (BFS) Structural Criteria is a living document that governs planning, design, and construction of all BART projects. Since its development, the document undergoes incremental changes and updates to reflect policy changes, changes in local, State, or national design codes and guidelines, advancements in engineering and technology, or based on the performance of past built infrastructure. In 2020, the BFS-Structural Criteria underwent a comprehensive update and was released with BFS version 3.2. This paper summarizes the updates to the Tunnels and Underground Structures Section of the Structural Criteria, and provides insights to the basis and logic of the requirements.

Dec 1, 2022

By K. Kim, H. Gao

A site-characterization strategy formulated for the probabilistic assessment of rock mass properties is presented. The strategy, which takes into account the variability of rock properties and the stochastic nature of the rock-failure process, entails determining probability distributions of rock properties by utilizing extreme value statistics and Monte Carlo simulation. Laboratory and, field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass can be estimated by using this proposed method. The results of the analysis can be incorporated into the design of underground structures. Then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1997

By James A. Doolittle

In the underground type of mining operation, the finer portion of the waste material commonly is pumped as a hydraulic slurry to a tailings disposal pond. (1)* The tailings slurry is deposited via a pipe manifold system located around the perimeter of the pond. This method of deposition produces zoning because the coarser material tends to settle out immediately while the finer particles tend to remain in suspension and are deposited progressively nearer the center of the pond. The manifold system must be raised periodically as the pond fills with the tailings material. Over a period of time, this procedure will produce a zoned embankment known as a tailings dam. A typical pond and dam are shown in Figure 1. In plan view, the dimensions of tailings dams can be on the order of miles, with the height of the dam reaching 100 to 200 feet. Due to such factors as inadequate compaction, inherently low strength of the tailings material, and the possibility of high phreatic surface, many dams at some point become unstable, i.e., the factor of safety against a slope failure approaches 1.0. Remedial measures are required to improve the safety factor in order to prevent massive failure of the dam. In most cases, stability can be improved by effectively flattening the slope of the dam as shown in Figure 2, but this is not possible in every case. Occasionally, a tailings dam is constructed adjacent to a natural or legal boundary so that it is not possible to construct a conventional berm or to reduce the slope angle with earth moving equipment. Even a terracing process would require removal of the material and this may not be practical. In such a situation, an alternate scheme to improve stability must be found.

Jan 1, 1974

By Richard E. Deery, Reginald E. Reid

A large portion of the public lands in the United States is managed by the U.S. Department of the Interior, Bureau of Land Management (BLM). Public lands administered by the BLM comprise about 39 per cent (270 million acres) of the entire Federal surface estate or about 1/8 of the surface of the United States. Most of this land, located in the 11 Western States, including Alaska, is available for mineral exploration and development. The BLM is a multiple-use land management agency responsible for the balanced management of the public lands and their resources. The BLM's task is to ensure the balanced and sustainable development of the public lands and resources. This task translates into the management of people and their use of the public resources. As a result, the BLM manages a diverse group of programs including recreation, range lands, timber lands, fish and wildlife habitat, watershed, wilderness, scientific, cultural, and historic properties, and most importantly for this paper, energy and mineral resources. The BLM has developed several new policies with respect to mining, including policies on inspection and enforcement, financial guarantees for reclamation, and the use of cyanide. The goal of these policies is to demonstrate to the American public that mineral exploration and development can be an integral part of sustainable development on public lands in an environmentally sound manner.

Jan 1, 1991

By Poltak Sinaga

PT Kaltim Prima Coal's 13.1 km overland conveyor was commissioned in 1991. It is of conventional 3 roller 350 troughed belt type. Cost and performance optimisation during initial design ended up with 5.4m/s belt speed, 1,000mm belt width to convey 1,350tph, and 7mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1,100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30mtpa. Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4200tph satisfactorily.

Jan 1, 2008

By D. C. McDonald, P. R. Whincup, H. Duke

Due to grade, overburden depth and stability and the presence of groundwater it was considered impractical to recover gold contained in unconsolidated palaeochannel sediments by conventional mining, dredging or borehole mining techniques. A series of field experiments was conducted to determine the feasibility of recovery of gold by in situ leaching from sediments located at a depth of about 80 metres. The test wellfield site and plant are described together with field test procedures, results and wellfield rehabilitation procedures. Choice of sodium cyanide as leachant and laboratory testing are discussed in relation to groundwater and sediment chemistry and problems encountered in field tests.

Jan 1, 1989

By Edward Finch, William F. Riggs

Selectivity and recovery of many industrial minerals can be directly affected by the carbon length, degree of unsaturation, and melt point of fatty acids used as collectors. Examples of several modifications are provided based on actual experiences of commercial applications. A review of recent history indicates that fatty acid collectors are applicable from C9'C18 in carbon length, however, not for all minerals. The mesh size, density, and surface characteristics of the particular mineral, as well as other related operating conditions, are important in selecting the correct fatty acid configuration. A review of some past programs are submitted as a guideline in the selection of fatty acids and supported by isolated, successful examples demonstrating the effect of carbon length and unsaturation.

Jan 1, 1986

By S. Kesler

Rössing Uranium Limited has operated since 1976 a large open pit uranium mine and extraction plant at a remote site in the Namib desert, South West Africa/Namibia. The geology (Berning, I., et al. Economy Geology) and the technical aspects concerning mining, grade control and metallurgy have previously been described (Rössing Uranium, Mining Magazin and Whyllie, R.J.M. "Rössing Uranium reaches rated production", World Mining). The improvement of leach 'extraction has been reported in 1984 (Kesler, S.B. et. al. "Uranium extraction at Rössing") and the installation of a central process control system has been described (Kesler, S.B. et al. "The introduction of a central process system at Rössing"). At the beginning of 1983 a decision was made to develop a computer system for metallurgical plant optimisation which included mass and volumetric balances, analytical assays for up to 5 chemical elements and the costs for the major consumables. Within 10 months this computer system was developed and implemented. A large number of test runs were made and computer studies were undertaken. The metallurgical division now has a scientific tool for production; planning for actual comparison with plant results and for strategic investigations and decision making.

Jan 1, 1986

By John Mahoney

We live in a world of change and the mining industry is enjoying some of the most rapid changes today that have been seen in a long time, We'd like you to open your mind to a new concept in material handling. Figure # 1 Shows a new concept combining some of the proven application advantages of the power shovel with which we are all familiar, and applies the advantages of the dragline for the benefit of the user. First, the hydraulic excavator enjoys tooth forces of the shovel because the dipper is attached to the machine with a dipperstick and boom, and can often actually realize greater tooth forces than a shovel because of the prize action of the dipper in hard digging. Second, the hydraulic excavator enjoys the application advantage of the dragline because both the operator and the machine are up above, sitting on top where the operator oversees the excavation and the machine's operating work range is greatly increased.

Jan 1, 1973

By J. Hazen, R. Jenner

This project was developed at the PCS Phosphate Mine in Aurora, NC. This site includes a surface mining operation, beneficiation plant and chemical processing facility located in the coastal plain of eastern North Carolina. The phosphate ore being mined at this operation is a 10 to 12 meter (35 to 40 foot) thick colloidal deposit located approximately 30 meters (100 feet) below the ground surface. The ore is pumped to the beneficiation facility where it is separated into clay, sand and concentrate streams. The concentrate product is utilized at the chemical plants to produce a wide range of products including fertilizer, industrial phosphates and animal feed products. The Cyclone Dike Builder (CDB) project developed a technique for dewatering the beneficiation tailing sand stream and providing innovative placement for dike construction. Future material balance requirements at the PCS Phosphate mine required an improvement in tailing sand placement technique to accomplish strategic objectives. The water volume of the sand slurry forces significant quantities of sand out of the dike profile during deposition. PCS Phosphate and MetPro Supply of Florida developed a mobile high-density hydro-cyclone station to remove most of the water and significantly increase the density of the sand being placed for dike construction. This high-density sand slurry is then effectively controlled using minimal heavy equipment operation.

Jan 1, 2004