Search Documents

By Rainer Antretter

While respirable crystalline silica (RCS) dust that arises in industrial production mostly emanates from point sources and can be well mitigated, the extraction of dust is much more difficult in underground construction, since locally generated dust spreads widely. Analysis of dust measurements shows that RCS values are difficult to predict, and effective dedusting systems are required to comply with permissible exposure limits (PEL) in breathed air. Dedusting systems are effective near the tunnel face, while dedusting of working areas away from the tunnel face is difficult or even impossible. In general, there is little temporal influence on the tunnelling work—except for drill and blast excavation—which makes it necessary to remove the deduster and ductwork from the face area. Concurrent work in the tunnel is affected by the backflowing air mass of ventilation and therefore the quality of this air mass must be considered. The use of personal protective equipment (PPE), e.g., dust filter masks, is considered the least-desirable safety measure available. However, for certain individual operations in the tunnelling process, the use of PPE cannot be avoided, especially if other technical mitigation measures are not possible. In tunnels with small cross sections for example, dedusting systems often cannot be accommodated and PPE must be used instead. This raises the question of whether the use of PPE can be avoided by designing appropriate excavation cross sections and allowing for the implementation of technically engineered mitigation measures. The paper highlights problems with dedusting measures and shows possible ways to achieve OSHA compliance.

Jun 13, 2021

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, despite its natural abundance, demand for coal exceeds its countrywide supply due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98 percent of total raw coal production in the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an environmentally friendly manner, especially in populated areas adjacent to the mining zone. This technology eliminates blast hole drilling, blasting and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks.

May 1, 2023

By E. Neumann

With fuel costs unstable but escalating, solid fuels are playing an increasingly larger part in industrial concerns. Coal, petroleum coke and wood are examined from a burner system design viewpoint and from operational experience in kilns, hot gas generators, etc. The burner of today must also handle multi-fuel tasks and allow immediate, painless switching from one fuel to the next as well as the simultaneous burning of two or mope fuels. The paper discusses the principle of burning alternate pulverized fuels as well as the practice both in the United States and around the world.

Jan 1, 1983

By Larry Murphy, Mohammad R. Jafari, David M. Giel, Sharat K. Kalluri

"Built in 1940’s to provide a key roadway arterial between New York and Boston, the Heroes Tunnel is the only highway rock tunnel in the state of Connecticut and is part of the Wilbur Cross Parkway. This 365.0 m long tunnel consists of two barrels, each with two lanes of traffic, and carries over 71,000 vehicles per day. For nearly 70 years, the tunnel has seen millions of vehicles pass through but time has taken its toll and now the tunnel lining, ventilation system and radial section joints are significantly deteriorated and in need of rehabilitation. Owned and maintained by the Connecticut Department of Transportation (CTDOT), CTDOT initiated a unique managed approach to mitigate the risk, social impacts and financial implications associated with rehabilitation of this tunnel. This new approach consists of performing field inspection and conducting a comprehensive study to explore six rehabilitation options, including construction of new tunnels and enlarging the existing tunnels. The main criteria for this study are: Impact on traffic and the resulting delay cost; Construction cost; Construction duration; and Construction complexity. This paper will present the results of the alternative study. PROJECT BACKGROUND Location and Importance Heroes Tunnel is located in the State of Connecticut within the Town of Woodbridge and the City of New Haven near the Town of Hamden border. Heroes Tunnel is the only true highway tunnel in the State of Connecticut. The tunnel is part of the Wilbur Cross Parkway (Route 15), a scenic connection between Hartford and New York. Originally constructed and opened to traffic in 1949, the tunneled portion of the parkway passes through the West Rock Ridge. The tunnel was originally named West Rock Tunnel, but was re-designated as Heroes Tunnel in 2003. Route 15 is a vital roadway within the State transportation infrastructure. In the vicinity of Heroes Tunnel, Route 15 carries approximately 71,000 vehicles daily. Locally, Route 15 provides access to residences, shopping centers, and points of interest, as well as other state roadways. Regionally, Route 15 connects New York to the Hartford area and serves as an alternate expressway route to I-95 and I-91. The tunnel is approximately 365.0 m long and passes through the West Rock Ridge. West Rock Ridge is an 11.3 km long rock ridge located on the west side of New Haven. A network of suburban streets abuts the mountain on all sides and a seasonal paved park road climbs to the crest of the ridge. Figure 1 depicts the tunnel topography and location."

Jan 1, 2016

"What is your history and how did you get involved in mining?Like many SME members, I came from a mining community with a family history in mining, in my case Walkerville, MT. Both of my grandfathers were underground miners. My father was a miner for a short time. He later sold drinks to the miners. Unfathomable by today’s standards, my dad would pick up the miners’ checks at the pay office and have them cashed and waiting with a shot and beer for the miners when their shift ended. My mother was a nurse, who from time to time, would patch up an unfortunate miner. I remember walking past multiple picket lines on the way to and from grade school, watching homes being boarded-up. I grew up with a deep respect for the critical relationship between labor and management.I had no intention of going into mining and initially set out to pursue a career in chemical engineering. But I attended my first two years of engineering at Montana Tech, due to the proximity and affordability. This is where I met Dr. Tom Finch, a mining professor who taught statics to the engineering students. After a coaching session in a hallway, half way through my sophomore year, I switched to mineral processing engineering. In his colorful way, Professor Finch advised me that, “You do not want to make #@*!! erasers and #@*!! Jell-O the rest of your life go talk to the guys in mineral processing.” He was very persuasive and here I am today.How about your involvement with SME?I encountered SME out of school and a little later in my career. Terry Maio and Jim Arnold invited me to local section meetings in the Missouri Lead Belt. That was my first exposure to the technical programming and relationship building that was possible at the local level. After Ozark Lead shut down and I relocated to Nevada, Rich Johnson, Scott Barr and Dave Collins encouraged me to attend my first annual meeting in Salt Lake City, UT. I joined SME at that time and was fortunate to be engaged by members like Art Schweizer and Jim Arnold, and I soon began the leadership progression for the Mineral & Metallurgical Processing Division. Since then, I have supported SME at the national and the local level serving in multiple roles and capacities."

Mar 1, 2017

By Yang Song, Li Shaokang, Wang Zhiqiang, Wang Jinjun, Li Guofeng, Su Meixuan

The paper investigates the triboelectric charging properties of calcium carbonate (CaCO3) particles under different conditions using a cyclone tribocharger. It explores the effects of airflow velocity, tribocharge material, and particle moving distance on the charge-to-mass ratio of CaCO3 particles. The study aims to provide guidance for the design of triboelectric separation systems for magnesite.

Sep 1, 2023

We have lived through a period of strong metal pricing during the past eight to 10 years. Copper has been hovering in the range of $3-$4/lb during much of the past eight years, averaging close to $3.30/lb. Gold increased steadily from less than $300/oz levels in the early 2000s, reaching almost $1,890/oz in the third quarter of 2011, before tempering back down to the $1,200-1,400/oz range in 2013. Iron ore prices started to rise in 2005 before the staggering increases experienced in 2008- 2010, reaching almost $190/metric ton in early 2011. During the past four years, iron ore prices have ranged from $100-180/t, averaging approximately $140/t. In the aftermath of such a run, it is perhaps too easy to forget where we have come from: The copper price averaged just 77 cents/lb during the six-year period from 1998 to 2003, and averaged just over $1/lb from 1989 to 1997. The gold price averaged $350/oz during the 10-year period from 1994 to 2003. Even more dramatically, iron ore traded in the range of $10-$15/t between 1985 and 2004. So, we have seen sustained, three- to four-fold increases in copper and gold prices, and 8 to 10-fold increases in iron ore prices.

Mar 1, 2014

By Walter E. Heinrichs

Early history of the district is typical of many, particularly in Southwestern United States. The usual early Spanish influence was felt; Marcos de Niza, Coronado and Father Kino are most notable, but authentic records regarding Spanish mining activities are sparse. About 1769 the Indian village of Tucson became a Spanish settlement. During the next century prospecting attempts were largely interrupted by the Indian, Mexican and Civil Wars. By 1870 Tucson had a population of 3200 and by 1880 the Southern Pacific Railroad extended all the way from Los Angeles. Pyrometasomatic copper ore was first produced with some local direct ore smelting done during the late 1800s. By 1907, a rail line was built from the Twin Buttes mines to Tucson by the Twin Buttes Mining and Smelting Company. World War I was a very active period, with mixed copper, lead, zinc, gold and silver production. This came mainly from underground replacement and contact metamorphic deposits and from practically all portions of the district. Some of these operations continued intermittently until the 1929 depression.

Jan 1, 1976

By The SME Sustainable Development Committee

The evolution of sustainable development in mining is recognized as a key contributor to sustainable development (SD), which is defined as the ability of current generations to meet their needs without compromising the ability of future generations to meet their own needs (Brundtland, 1987). This includes, in equal parts, social, economic and environmental impacts ? triple bottom line (Munashinge and Shearer, 1995). Alternately, sustainability has been defined in relation to social, natural, human, physical and financial capital. Our way of life relies significantly on the materials provided by mining, while mining activity affects the triple bottom-line or the five capitals. The mining community and its professionals have come to realize the importance of engaging all stakeholders in the discussion on sustainability. SME, as the leading professional mining organization, has been involved in these discussions. The society has various initiatives in sustainable development for members and stakeholders. The objective of this article is to: provide historical context for current trends in mining and SD and share SME sustainability initiatives ? their goals and rationales ? with the broader mining community. This article is timely because the past year saw two landmark forums on sustainable development: Rio+20 ? the 20th meeting of the United Nations Conference on Sustainable Development, and MMSD +10, the Mining, Minerals and Sustainable Development project 10 years on. Furthermore, this year marks the 10th anniversary of the Milos Declaration on the minerals professional?s responsibilities in achieving sustainable development, forums in which SME was involved.

May 1, 2013

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Abutment loading conditions are important to gate-road layout and support design in longwall mining systems. Ground support systems are often designed based on mine experience [1,2]. Convergence monitoring is one method of ground support monitoring that can be used to infer increases in pillar stress. Convergence of a yield pillar was measured regularly over the course of six months as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head-gate entry access for specific geologic and mining conditions. 

By P. Rusin

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environ-mentally unacceptable. Bio-reductive leaching of such ore samples at MBX resulted in high recoveries of silver and molybdenum. When baseline 3-day cyanide bottle roll tests were conducted on manganiferous oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bio-reduction with 99.8% dissolution of manganese. A follow-up cyanide bottle roll test yielded an additional 8.5% silver recovery for a total recovery of 94.5%. Baseline 3-day acid bottle roll tests of the iron oxide molybdenum ore yielded 1.8% moly. However, bio-reduction solubilized 93.3% of the moly into the growth medium. An additional 0.3% moly was recovered during the follow-up acid bottle roll test. Microbial treatment of refractory oxide ores with bio-reductive bacteria resulted in higher recoveries of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and moly was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1992

By E. McCarthy

"INTRODUCTION Talc is a hydrous magnesium silicate with the approximate elemental composition 4MgO.3SiO2.H2O. It is one of the layered phyllosilicates (like kaolin and mica) but it differs from these in that it is relatively hydrophobic. This is due to its unique crystalline structure whereby a brucite inner layer is sandwiched between silica layers and the adjacent silica layers have no interlayer bonding other than van der Waals forces. This allows talc to be sheared easily along this basal plane, and the surface is covalent not ionic. Talc occurs both as a relatively pure material (>90% talc content) and in conjunction with many other minerals in proportions all the way from 1% to 90%. At lower concentrations, it is often considered a nuisance mineral when it occurs with base metals like copper, molybdenum or nickel or with precious metals like platinum or palladium. It floats readily with these materials and often is suppressed using guar gum or carboxy methyl cellulose which will absorb along the basal surface and make it hydrophilic. Alternately if the reduced ore is hydrophobic, like MoS2, then a partial oxidation of the sulfide will convert the surface to a hydrophilic oxide and the talc can be floated away in a separate step. Talc in grades from 20 to 90% has been commercially exploited in a wide range of pigment (paint and paper), material (ceramic, construction and cosmetic), reinforcing (polymers and composites) and functional (pitch adsorbent, lubricating agent) applications. Initially these tended to be local or regional markets, but eventually with certain higher purity grades, cosmetic, polymer and ceramic applications became valuable enough to be national and trans ocean markets. TALC FLOATATION PLANTS This drove the need for higher purity grades of talc and initially this need was met primarily by ore sorting. This works well for certain deposits with well crystallized talc lenses, but for ores, such as those from widely available ultramafic deposits, where the liberation size is closer to 100 microns, sorting is not effective. That drove the need for floatation and the first investigations were published by Clemmer and Cooke of the US Bureau of Mines in 19362. The first commercial floatation plant was installed in Johnson, VT by the Eastern Magnesia Talc Co in 1937. The circuit is shown in the schematic (Figure 1). The ore was an ultramafic, serpentine derived talc; mineralogy was about 55% talc, 40% ferroan magnesite and 5% oxides, sulfides and other silicates. The oxides include hematite and chromite, sulfides pyrite and gerstorffite and silicates chlorite, serpentine and mica. After crushing, the ore was dry ball milled and then air classified to remove minus 325 mesh fines. The coarse fraction was further classified to cut at about 100 mesh and the fines from this were the feed to floatation. The -325 mesh (about 15% of the ore) was sold as a paint grade and the plus 100 mesh (about 25% of the ore) was screened to make an asphalt backsurfacing grade."

Jan 1, 2018

By Adrian Fleming

Adrian Fleming is Executive Vice President of Exploration for Golden Star Resources Ltd., Denver. Adrian is an Australian who graduated in 1973 with an honors degree in geology from Newcastle University, New South Wales. His extensive international experience has spanned exploration, project development, and operations for both large and small companies in Australasia, Southeast Asia, North and South America, and Africa. Adrian has been with the Golden Star group of companies for four years and he is responsible for all exploration activity. ABSTRACT Golden Star acquired the rights to the Omai prospect in 1985 at a time when the country of Guyana was out of favor with the exploration fraternity. Subsequently in the late 1980s and early 1990s, Golden Star acquired exploration properties in Suriname and French Guiana well ahead of its competitors. Golden Star's strategy entailed identifying windows of opportunity and aggressively pursuing them. We also recognized that the Guiana Shield hosted a significant area of highly prospective greenstones which were comparable in metallogenic potential to similar terrains in eastern Canada, western Australia and west Africa. The geological skills Golden Star developed and the exploration techniques employed to explore deeply weathered rocks are described. The paper highlights the key elements of Golden Star's strategy and illustrates how some of the milestones reached by the company led Golden Star to establish an enviable portfolio of gold and diamond properties in the Guiana Shield.

Jan 1, 1998

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive, and it is quantified as a confined or unconfined velocity. The confined velocity is more significant as explosives are usually used under a definite degree of confinement. This study evaluates the stepwise increment of the air-deck volume from 10 to 30 percent, and its effect on the VOD. The VOD estimation in the 172-mm-diameter explosive column was conducted using the Dáutriche technique. The air-deck volume increment has an attenuation effect on the steady-state VOD, and detonation failure is high at 30 percent air-deck volume. This attenuation effect is directly linked to the explosive’s rating and efficacy. The air-decking approach in this study is different from conventional air-decking techniques in that it does not employ the fixed blasthole parameters, air-deck volume and specific VOD. 

By J. M. Christian

Silver has been a much maligned metal in recent years. In the last three and a half years the price has fallen from around US$7.00 -$7.80 to as low as $3.50 this spring. It has consistently under-performed most other precious metals in the past few years, and has fallen to its lowest levels since the late 1940s in inflation-adjusted terms. Perhaps this is beginning to change. Since April, silver prices have outperformed gold and platinum. While this may continue in the years ahead, key questions remain regarding the pace and timing of any future silver price advances. I want to talk about the supply and demand factors that have led silver to its recent position. Also, I will outline a possible path for silver supply, demand, and prices for the next several years. Before I dive into my discussion of the silver market, allow me to explain who I am. One of the points we always make to clients early in a relationship is that, when you are listening to someone's opinions, you always must remember who it is you are listening to, and why he might be saying whatever it is he wants you to hear. So often, people take opinions from brokers, traders, or investment advisors as gospel truth, never stopping to ask themselves two key questions: Is there any reason to believe that this person knows what he is talking about, and, second, is he trying to sell me something, in telling me this.

Jan 1, 1992

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and con¬crete is described Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fastopening valve discharges the com¬pressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh-pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited

Jan 1, 1997

By G. A. Plakhin, A. V. Luganov, V. A. Luganov, G. V. Gorbatenko

In order to extract gold from the complex sulphur-arsenic bear­ing raw materials and to remove arsenic and sulphur from the process in an ecologically safe form we have studied oxidizing roasting of highly arsenic gold bearing concentrates with soda, leaching of cinders, processing of the obtained solution and extraction of gold from the cake. There were processed concen­trates containing from 5 to 28% of arsenic, 12-20% of sulphur in the form of pyrite and arsenopyrite. The content of gold in the concentrates was 4-75 git. The roasting temperature was changed in the range of 773-l 173K, the consumption of calcined soda was 75-200% of stoichiometric necessarily for bonding of arsenic and sulphur into the water soluble compounds, the dura­tion of the process was varied in the range of 10-120 minutes. Under roasting in optimal conditions up to 97% of arsenic and 95% of sulphur go into water soluble compounds. The out­put of cake is 65-70% of the concentrates. The extraction of gold from the cake is higher than from the raw concentrates. The technology has been tested on a pilot plant scale

Jan 1, 1996

By H. M. Park

Risk is a major factor in all mining activities, arising from many internal and external variables. The authors? research has resulted in a systematic method for the quantification of risk in mining projects (Park, 2012), and this research is being presented in a series of papers. The first paper (Park and Nelson, 2013a) identified the variables associated with risk in mining projects, and their effects and was published in the October issue of Mining Engineering magazine. The second (Park and Nelson, 2013b) discussed methods of assessing the overall risk associated with those variables (published at www.me.smenet.org), and presented a statistical model based on a survey of 31 experts. This paper will present an evaluation of the statistical model, using data from previous mining investment decisions in which the authors have been involved.

Oct 1, 2013

By Richard O. Rouse

Today, I want to challenge this audience by charging each of you to be a greater manager and superior engineer to manage and engineer our way through the 1980's and profitably overcome all the present and proposed government regulations. May of the present and proposed regulations will tax you and your company's management and engineering to the brink of physical and monetary exhaustion, but I believe we can succeed and coal can be America's answer to her hungry energy needs. To put our 1980's challenge into perspective, I want to give two great challenges we must overcome. First - We must improve on our process of compliance to new government regulations in the technical and equipment end of our industry. The Lord said, "Let There Be Light". MSHA said, "Let there be light in underground coal mines". Since that time, we have lived through an unmanageable and tremendously costly period of compliance.

Jan 1, 1980

By Bruce McKinstry

INTRODUCTION In June of 1992, the Bureau of Reclamation, United States Department of the Interior, awarded the contract for construction of the Sixth Water Aqueduct to the Fedrick-Redpath Joint Venture. This aqueduct, a segment of the Diamond Fork Power System, Central Utah Project, diverts water from Strawberry Reservoir into Sixth Water Creek and, when complete, will replace the old Strawberry Tunnel which was driven in the early 1900's. The new aqueduct is being built primarily as a result of deterioration of the old tunnel, but will also have a higher capacity and more positive control than the old tunnel as well as the capability to incorporate a turbine into the system at a later date. The Fedrick-Redpath Joint Venture is comprised of C.R. Fedrick, Inc. of Novato, California and J.S. Redpath Corporation of Tempe, Arizona. Fedrick, with its experience in pipelines and heavy construction, will construct the 4200 ft surface pipeline and flow control structure; Redpath, the managing partner, performed the underground work consisting of a 600 ft vertical shaft and 3300 ft tunnel. The project is located in the Uintah National Forest, approximately 20 miles east of Provo, Utah at a mean elevation of 7000 feet above sea level.

Jan 1, 1995