Search Documents

By Horst H. Gielen

Bong Mining Company/Liberia provides the rare opportunity to compare two generations of grate kiln pelletizing plants operating on the same magnetite/hematite ore basis. In this paper advantages and drawbacks are compared: mechanical aspects, energy-savings, pellet quality. Plant I with up- and down-draft drying gas flow. Plant II runs only on down draft drying and incorporates a heat-recoup system. Ferteco Mineracao/Brazil operates a Lurgi straight grate plant since 1977 on hematitic pelletfeed. Energy-political situation and char- coal as energy source in Brazil are reflected also in the search for alternative fuels for pelletizing. First measures and results are reported as well as intended further steps towards a 100 % oil replacement.

Jan 1, 1983

By A. P. Massmann

Design for economical operation, minimum operating labor and minimum maintenance for labor and supplies are virtually inseparable. Each consideration has a vital bearing on the other. Let us assume that we have the design complete for the most economical operation with a minimum of operating personnel. This means, in addition, that we have the fewest number of operating units consistent with the product requirements for a team or metallurgical coal which we are called on to produce. The number of units will vary greatly, being influenced by design, washability characteristics, tonnage and degree of quality control necessary by reason of producing a product for metallurgical, steam or domestic use. The units involved most ordinarily for any type coal preparation plant will number as a minimum the following: 1. Hoppering R.O.M. Coal 2. Feeding

Jan 1, 1959

By Michael A. Trevits

A mine fire represents one of the most dangerous and challenging safety issues facing underground mine operators. Given the right circumstances, a mine fire can occur at any location in the active or abandoned mine workings, can quickly grow beyond control, and threaten the welfare and livelihood of the entire underground workforce. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), has been conducting an in-depth program of research addressing mine fire prevention, early and reliable fire detection, and mine fire suppression technologies. One portion of this program is focused on understanding the characteristics of mine fire combustion products and flame spread through large scale deep-seated (firmly established) fire tests and use of computational fluid dynamics (CFD) modeling. In this study, two deep-seated fire tests were conducted; one fire consisted of coal material and the other utilized the two most abundant fuel sources found in a coal mine: coal and wooden cribbing blocks. The fires were burned to completion while the combustion products were collected and analyzed. In addition, an array of thermocouples was placed within the body of the material to measure flame spread rate. The coal fire test information was then used to develop a CFD model of the fire. This paper describes the fire tests, provides insight into characteristics of flame spread, and presents the CFD modeling work results.

Jan 1, 2009

By J. A. Barrera-Godinez

Traditional batch flotation tests produce a limited number of data points from which to evaluate the kinetics of the process. In this research, continuous weighing of froth, from a modified circular flotation cell, using a computer/data acquisition system., has been coupled with chemical analyses from intermittent froth sampling. This combination has permitted the experimental data to be smoothed such that the flotation kinetic parameters could be determined with enhanced confidence. To demonstrate the procedure, a galena ore was floated to permit flotation kinetics to be investigated as a function of cell parameters. It was shown that the kinetic data of this lead flotation most closely correlated with the Huber-Panu three parameter model. In addition the results illustrated the effect of froth thickness, froth scraper rate and air flow rate on the cell performance, in terms of mass flow, grade and recovery.

Jan 1, 1990

By Mark E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problems simultaneously. Previous attempts at solving these problems separately, although successful, fail to take into account the interrelationships between these problems. Project structure serves as the outline of this paper, which is directed towards a mining engineering audience. Generalized in its organization, this concept is useful for long, intermediate and short range scheduling. Actual applications are mentioned which show that the concept is also applicable to mining a variety of ores.

Jan 1, 1982

By M. L. Harris, I. Zlochower, M. J. Sapko, I. E. Perera

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effective, rock dust must be able to disperse as individual particles to inert. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anti-caking additives after being exposed to moisture and then dried. The dusts were exposed to moisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anticaking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Laboratory (LLL), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for one day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for six months. This report details the analysis and characterization of anti-caking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber. INTRODUCTION In order for a coal dust explosion to propagate, five elements are required. In addition to the fire triangle in which three elements are necessary to sustain a fire—fuel (coal dust), heat (ignition source), and an oxidizer (oxygen in air)—a combustible dust explosion requires dispersion of a dust cloud (pressure wave) and confinement of a dust cloud (underground mine entry) (1). Coal dust explosions can originate anywhere in a mine. For example, when a small volume of a flammable methane and air mixture is ignited in a closed end, the high-temperature gases rapidly expand to create a pressure wave, sometimes referred to as a “pioneer wave,” that may steepen into a shock wave as it propagates away from the ignition source. The shock wave produces a wind that disperses the dust preferentially from any elevated and exposed surfaces (roof, ribs, belt structure, cribbing, etc.). Factors that are known to affect the intensity of an explosion are the dust particle size, the location of the dust within the entry, the dust dispersibility, and the volatility of the coal dust (1). Particles less than 75 μm (< 200 mesh) in size are most reactive (2). Dusts that are located on the roof, ribs, and elevated surfaces are more readily dispersed than dusts on the floor. Therefore, application of quality rock dust in sufficient quantities is essential to inert coal dust and to prevent continued flame propagation. 30 CFR 75.402 and 75.403 require 80% total incombustible content be maintained within 40 ft of the face, and 30 CFR 75.2 defines rock dust acceptable for use in underground coal mines. It also defined that “when rock dust is wetted and dried, will not form a cake”.

Jan 1, 2019

By N. Kuyucak

While Acid Rock Drainage (ARD) occurs naturally, its management poses challenges especially at the decommissioned sites. Two passive systems were designed and implemented at two different decommissioned mining sites in Canada in order to treat the seepage with ARD characteristics. One seep originating from a reclaimed tailings pond was neutral mine drainage (NMD) containing circumneutral pH and dissolved metals (e.g., nickel, zinc) in elevated concentrations. The other ARD from a tailings stack showed net acid drainage characteristics with low pH and higher metal concentrations than regulated limits. Due to the different ARD characteristics occurring at each site, different types of treatment systems were designed and implemented. Both sites experience extreme winter conditions. The NMD has been treated mainly by limestone drain and aerobic systems since 1997. The acid ARD has been treated by a system consisting of an anaerobic sulfate reducing bacteria (SRB) cell, an aerobic cell and a limestone filter since 2004. As this site has no access roads, space, or power, a significant capital cost as well as sludge disposal/storage requirements would have been required to institute a chemical (active) treatment system. Both systems have been successfully treating seepage and producing a water quality year round that could comply with regulated objectives.

Jan 1, 2010

By Per-Martin Sandgren

LKAB&apos;s ores have specific mineralogical properties that make them especially suitable for the production of super-grade concentrates. Conditions are particularly good for this purpose at Malmberget, where a concentrate for high-purity sponge iron production has been produced for many years. Until 1978 the approximate assay was 71.2 % Fe and 0.45 % SiO2. Since then the assays have been improved by process modifications to approximately 71.5 % Fe and 0.20 % SiO2. Scope exists for still further improvement. In recent years the production of fractioned concentrates has been started. The material lies within the size range 74-125 µm and the approximate chemical analysis is 71.6 % Fe and 0.30 % SiO2. Other special products are under discussion. The Malmberget ores are also suitable for the production of high-purity direct reduction pellets with a SiO2 content below 1 %.

Jan 1, 1981

By D. G. Purdy

Planning, as defined in Webster&apos;s New Collegiate Dictionary, is a detailed program of action designed to achieve an end. When developing a detailed plan to incorporate all the complex activities involved in a surface lignite mine, many elements must be carefully evaluated as to the individual and cumulative effects on the end result. The following elements are generally evaluated when planning a surface lignite mine: ? Reserve evaluation, including lignite quality characterization; ? Delineation of mining parameters, including lignite recovery factors, geotechnical factors, land control factors; ? Selection of mining blocks; ? Pit sequencing; ? Reclamation, including soil reconstruction design and land use planning; ? Overburden handling design; ? Selection of equipment; ? Sizing of equipment; ? Manpower requirements; and ? Other elements, including contract negotiations and execution, financing, investment return, operation economics, permitting and scheduling.

Jan 1, 1985

By S. D. Thompson

Since 1965 several researchers have independently developed computer models for designing gathering belt and surge bin capacities in underground coal mine belt systems. Table 1 summarizes the models applicable to U.S. mining systems. Most of the models, employ the Monte Carlo simulation technique. Basically, the belt loading at each loading point is randomly produced from probability distributions. In some cases, a combination of deterministic calculations and probability distributions are used to simulate the loading. Once the loading is simulated, it is systematically moved through the belt system in a deterministic fashion based on belt speeds, belt lengths, and storage bin discharge rates. The coal flowing from each loading point is tracked as it moves through the belt system. When the loading from tm different sources combines on a belt or in a surge bin, checks are made to determine if capacities have been exceeded. If capacities have been exceeded the amount of spillage is calculated. At the end of the simulated time period, the cumulative spill- age is used to evaluate the belt and surge bin capacities. Naturally, a considerable amount of spillage indicates the capacities are unacceptable. Acceptable capacities are generally indicated by minimal spillage. Numerous trial simulations are often necessary to find the acceptable capacities.

Jan 1, 1987

By Virginia T. McLemore, Abena S. Acheampong-Mensah

Critical mineral endowment of mine wastes in two mining districts in New Mexico (Copper Flat at Hillsboro and Carlisle-Center mines in the Steeple Rock district) will be characterized and estimated. “Beta-testing” of USGS procedures was performed. Potential critical minerals at these deposits include As, Bi, Te, Zn, Co, Ni, Mg, Mn, and fluorite. pH and particle size of samples were analyzed to determine weathering and migration potential of heavy metals. Soil pH was also measured to determine the potential for Acid Rock Drainage. The pH of the waste rock piles ranged from 3.66 to 5.67 which indicates fine- grained pyrite or sulfide oxidation. The samples collected from the tailings however, showed a different range of pH, from 6.30 to 8.62, probably due to the presence of carbonates. Difference in particle size fractions and its distribution along the slope are generally influenced by natural occurrences (e.g., gravity and pre-mining hydrothermal alteration) and operational activities such as material piling or dumping. Future work includes analyses of mineralogy and particle size correlation and estimation of critical mineral endowment of these mine wastes at New Mexico.

Feb 1, 2024

By Peter Zhang, Daniel Su, Bo Kim, Zoheir Khademian

Building on the research results and knowledge obtained from the ongoing National Institute for Occupational Safety and Health (NIOSH) Gas Well Stability Research, researchers from the NIOSH provided detailed analyses on potential longwall mining and gas well casing interactions at an unconventional shale gas well pad in a West Virginia longwall mine. Following the recommendations from recent research findings, the 5-1/2-inch production casings in all five wells were left uncemented from 4,200 feet below the surface to the surface. Prior to the first longwall panel excavation, NIOSH researchers conducted sophisticated three-dimensional numerical modeling to predict longwall-induced deformations and gas well casing stresses, which were compared with post-first panel and post-second panel mining 40-arm caliper surveys. The pre-mining predictions and comparisons with post-mining 40-arm caliper surveys were presented to all parties involved, including the coal and gas operators, Mine Safety and Health Administration (MSHA), Pennsylvania Department of Environmental Protection (PADEP), and West Virginia Department of Mines (WVDOM), prior to the re-entry operation on December 13, 2022. To date, the re-entry operation is a resounding success.

Jul 1, 2023

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By Omar A. Muhtadi

Brohm Mining Corporation, in conjunction with Geobiotics, Inc. has nearly completed a pilot heap biooxidation test on sulfidic ore from the Gilt Edge Mine near Rapid City, South Dakota. Some results from the pilot testing have shown the correlation between the extent of biooxidation and the increase in cyanide gold recovery seen in the laboratory. Bench scale testing showed approximately a 1: 1 correspondence between percent biooxidation and percentage increase in gold recovery. The economics of large scale biooxidation were also evaluated in terms of increased gold recovery versus the time and cost of biooxidation. In the pilot test, the rate of biooxidation became limited by the acid water neutralization system. Later in the test, measures were taken to overcome this problem. Results from bench scale column bioleach testing showed that the Gilt Edge sulfide ore is quite amenable to biooxidation with a substantial increase in gold recovery with just partial biooxidation. Direct cyanide gold recovery of 51 % on ore crushed to -3/8" was enhanced to 82-85% after oxidation of37% of the sulfide as measured by iron. Laboratory experiments also showed that the slow rate of biooxidation of this ore could be accelerated by removal of metal sulfate build up from the leach liquor. The combination of these normally non-toxic metals became inhibitory to biooxidation if not removed by the neutralization circuit.

Jan 1, 1995

By Dan Ifrim, Andre Solecki

Tunneling could be a major challenge to tunneling contractors as tunneling operations can be seriously affected by the Tunnel Boring Machine (TBM) performance. Specifying the appropriate TBM methodology, selection of systems and features, is critical for managing tunnel risks and contribute to successful tunneling project. The paper analyzes tunneling records from the recently completed City of Toronto’s Ashbridges Bay Treatment Outfall tunnel project and underlines the righteous selection of the TBM type and associated TBM systems in achieving good advance rates during tunnelling and managing project risks. The paper intends to draw attention of a few aspects of TBM technical specification importance and highlight the lessons learned from this process.

Jun 13, 2023

By Kent D. Gastreich

As the number of prime surface coal mining sites diminishes with time and with the potential for increased coal demand, areas that were previously not mined because of their difficult mining conditions, marginal economics, and controversial environmental nature, will have to be considered if surface coal mining is to continue in the future. Such sites include areas near major rivers, streams, and lakes. The name most commonly given to these areas by regulatory agencies is "wetlands". The exact definition(s) to the term "wetland" will be discussed later in this paper. Most coal operators are now more than familiar with permitting requirements under the Surface Mining Control and Reclamation Act of 1977 (SMCRA). The SMCRA permanent regulatory program recognizes the fact that coal mining operations will periodically encounter streams, wetlands, etc. Although discussed in various sections of the permanent program regulations, the relationship of coal mining operations to wetlands is particularly evident in the performance standards regarding hydrologic balance and protection of fish, wildlife and related environmental values.

Jan 1, 1980

By J. Casado

This paper presents the results of an analysis and summary of relevant literature on the mechanism of cementation of metals in acidic aqueous media, with the aim of reconsidering the conventional assumptions. The simplicity of the process as a mere galvanic metal displacement is discussed, and the real effects of pH and hydrogen pressure in different cases assessed. Finally, an alternative mechanism scheme with respect to the role of hydrogen species, in agreement with reported data, is proposed.

By John W. Carson, David S. Dick

The last few years have produced new methods of characterizing flow properties of bulk solids. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field condi¬tions. In addition, the effect of large par¬ticles on a material&apos;s flow properties (cohe¬sive strength, bulk density, wall friction) can be determined as well as the effects of var¬ious additives such as freeze conditioning agents. New developments have occurred with devices to improve the reliability of solids flow. Much attention has been paid to find¬ing ways, by using inserts, to provide a mass flow pattern with relatively shallow hopper walls. Such devices can also provide reli¬able in-bin gravity blending of bulk solids or completely nonsegregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. The technology and hardware for running bench scale flow tests on bulk solids samples and transforming the results into reliable designs has been in existence for nearly 30 years (Jenike, 1964; Marinelli and Carson, 1986). It has been shown repeatedly that reliable materials handling systems can be designed to avoid the problems of no-flow due to arching or rat-holing, erratic flow, segregation, loss of capacity, or spontaneous combustion. Running flow properties tests and carefully designing a bulk handling system are not expensive, particularly when compared to downtime costs and continual flow problems. New developments in characterizing flow properties of bulk solids include: • a shear tester for measuring the properties of run-of-mine ores containing large par¬ticles; • attrition testers to simulate a wide range of flow conditions; • a tester to measure the wear rate of liners in bins, feeder parts, etc.; • a dustiness tester to measure the potential for dust and the effect of dust control meas¬ures; and • techniques for measuring the strength of frozen ores and the effect of freeze condi¬tioning agents. In the area of improving the flow of bulk solids, there are new techniques for ensuring reliable flow without using up excessive headroom. These include: • belt-to-belt transfer chutes to handle po¬tentially sticky, abrasive, and dusty ores; • designs for the interface between a bin/ hopper and apron or belt feeders to avoid hangups and minimize feeder loads; methods to feed solids reliably into a pres¬surized process; and designs for handling systems that will mini¬ mize attrition, avoid segregation, or auto¬matically blend materials together. Characterizing flow properties Large shear cell It has long been known that the cohesive strength of a bulk solid is due mainly to its fine fraction. However, the effect of the larger particles (that were assumed to re¬duce the strength) could not be measured. The development of larger scale (205 mm¬diam and 0.6 x 0.9 m or 8 in.-diam and 2 x 3 ft) shear testers has made it possible to measure the properties of a wider range of materials. Now cohesive strength measurements can be made with up to 100 mm (4 in.) particles. The results obtained from the large shear testers, together with the results of the nor¬mal shear tests on the fine fraction, are used in the design of reliable stockpile reclaim systems and crusher feed systems. A high percentage of large particles can reduce the measured shear strength of a bulk solid. However, segregation may alter the size distribution and should therefore be considered (Carson, Royal, and Goodwill, 1986). In addition, larger particles will

Jan 1, 1989

By Pablo Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occuring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, California recovers potash from natural brines, but uses fuel to accomplish evaporation. Under proper meteorological conditions the use of solar evaporation might be desirable from the economical standpoint. Of course, this may not be true when, if by artificial evaporation, a group of very valuable salts are recovered. This is the case of the American Potash operation at Trona. Solar evaporation has its limits. The working temperature is low. We may say, just to cover most areas of the world where solar evaporation may be practical, that it will take place between 18°C and perhaps around 45°C. In most cases the average working temperature expected will be around 25°C.

Jan 1, 1963

By M. J. Zdunczyk

The final 1995 figures on industrial sand and gravel have not yet been compiled by the US Geological Survey (USGS). There is usually about a nine-month lag time in receiving and compiling this information. However, USGS estimates that domestic production of industrial sand and gravel will increase about 4% to 28.2 Mt(31 million st). The average unit price is expected to increase as well. The top five producers during 1995 were Unimin, US Silica, Fairmount Minerals, Oglebay Norton and Morie Co. Glass manufacturing for containers, automobiles and buildings was mixed during 1995. Containers, the largest consumer of silica sand, remained steady, with regional increases. However, silica use in glass containers face increased competition from plastic and recycled glass (cullet). It was reported that the Pepsi Cola announced plans to replace glass containers with plastic during 1996.

Jan 1, 1996