Search Documents

By Y. C. Kim

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the U.S. has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms.

Jan 1, 1988

By Terence G. McCusker, E. Roy Anderson

A four-mile length of interceptor sewer tunnel in Manhattan has finished sizes ranging from 10'6" to 14'6" horseshoe. Mixed face conditions were anticipated in three areas and encountered in five. All were short but since the tunnel lies well below the water table and failures would involve important utilities, major structures and human lives, great care had to be exercized in choosing a construc¬tion method. Chemical consolidation was selected as the best approach with compressed air working as a backup system. Initially grouting was accomplished from within the tunnel, but treatment from the surface was more successful and was later adopted. The soils consisted largely of impermeable weak silts and it was found possible to inhibit access of water to this material so that it could be controlled by breasting within the tunnel without loss of stability. It is concluded that in the interlayered permeable and impermeable soils encountered, chemical grouting would successfully stabilize the working face. INTRODUCTION An interceptor sewer is currently under construction along the entire length of the west side of Manhattan. When complete, the tunnel will intercept and divert to a treatment plant (also under construction) a daily flow in excess of 200 million gallons per day. About 9 miles of the interceptor sewer is in tunnel and the remain¬der is cut-and-cover construction. The tunnel is almost entirely in Manhattan schist but where its alignment crosses major faults at comparatively shallow depths, mixed face and earth conditions are

Jan 1, 1997

By Lewis L. Oriard

The authors outline the development and application of blasting methods put into use 11 years ago at the Berkeley Open-Pit Mine, Butte, Montana. The blast design uses a very short delay (5 milliseconds) between detonation of explosives charges, a feature challenged several times in principle despite its success for Anaconda. Concern is expressed over the categorical rejection of very short delay blasting which can make the difference between success and failure of major mining operations. There is ample evidence to show that the method can be used successfully and not violate the concerns of the public.

Jan 1, 1980

By Charles Rubin

Mining is a capital- and labor-intensive business, and profitability often depends on the ability to squeeze maximum efficiency out of every piece of equipment to achieve safe production. This means keeping every mechanized drill, loader, truck and bulldozer operating at all times, and having a system to coordinate the movements of people and personnel. Mines often use wireless radios to connect equipment with management systems. But growth and changes in a mine?s profile over time can require upgrades to the wireless network. In its openpit gold mine near Carlin, NV, Newmont Mining Corp. has recently upgraded to microwave radio systems to increase bandwidth while maintaining round-the-clock uptime on its wireless network. For many of its operations around the world, Newmont uses Minestar, an operational control software system that allows administrators to dispatch equipment operators and use GPS to track the precise position of every piece of equipment in an operation. Each of the approximately 150 pieces of equipment at the mine has a radio on board. These radios connect to a network backbone that carries information between the equipment and the mine?s operations center. When traffic began to bog down on this network, Newmont upgraded to Exalt microwave backhaul systems to carry dispatch, inventory and control information throughout its operation.

Jan 4, 2010

By M. Shahsavar, J. Sattarvand, J. Gomez

Mining can be categorized as a hazardous activity, considering some factors such as environmental conditions with a considerable presence of humidity, suspended particles, or falling rocks have affected the severity and number of accidents compared with other economic sectors. The industry analyzes incident reports to narrow the rate of severe injuries and fatalities, conducting root cause analysis and identifying leading indicators. As the International Council on Mining and Metals noted, the vast trove of incident data is not analyzed as much as possible due to a lack of analytics expertise at mine sites. However, machine learning could solve the problem of analyzing all the incident data in a no-timeconsuming way, considering the abundant data, and without using expert personnel in data science. Thus, a Convolutional Neural Network and a Naïve Bayes model were introduced to perform classification in the MSHA database. The database from 2020 consists of 60 fields to describe safety incidents; these fields include mine I.D., accident date, subunit (mill, surface), material extracted, and other metadata.

Jun 25, 2023

By P. C. Schmall

Ground freezing has been used for the sinking of deep mine shafts for more than 140 years. While advances in refrigeration technology have refined the overall freezing operation, the basic ground freezing concept remains the same. This paper presents an overview of the ground freezing process and the unique advantages that ground freezing brings to shaft construction. Design and construction considerations, including instrumentation and monitoring, are discussed. Case studies are presented to illustrate ground freezing applications for mine shaft installation.

Jan 1, 2010

By V. B. Achanti

Reliability of the compressive strength of a coal seam determined in the laboratory is often subjected to debate. Effects of the coal seam's inherent characteristics, specimen preparation, testing procedure, testing condition, and a number of tests often result in drastic variation of the strength data. This paper deals with the development of a testing procedure for determination of coal seam compressive strength in the laboratory. Coal samples from two different coal seams were tested. First, the inherent characteristics of each coal seam such as coal structure, Hardgrove Orindability Index (HOI), Slake Durability Index, proximate analysis, and mechanical properties namely Young's modulus and Poisson's ratio were determined to categorize them in terms of their characteristic severity liable to produce variable strength data in typical laboratory tests. Second, two commonly used laboratory specimen shapes namely; cylindrical and cubical, were tested to determine which shape produced the least variation of data and reproducible strength values. Third, four loading rates within the static testing range (Le. 0.007 MPa/s (1.0 psi/sec), 0.07 MPa/s (10 psi/sec), 0.34 MPa/s (50 psi/sec), and 0.7 MPa/s (100 psi/sec)) were used to determine an ideal loading rate. Finally, the number of test samples required to produce strength data within the acceptable standard deviation, considering coal seam characteristics were established.

Jan 1, 1996

By Louis A. Panek

Research on roof bolting has developed significant information with respect to the functions that can be performed by properly installed bolts and the methods that can be used to ensure that effective installation has been achieved. The present paper brings together results that are pertinent to the design of a bolting system for reinforcing horizontally stratified mine roof with vertical bolts. The design approach is based on the use of bolts to decrease the maximum bending stress within an arbitrary sequence of roof strata (such as shown by figure 1) in which the only loads are the weights of the individual beds. The use of rock bolts to achieve other objectives, such as to stabilize a fractured rock mass on the periphery of a mine opening (3), is excluded from consideration herein.

Jan 1, 1964

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By Terry Ramsey, N. Finkelstein

INTRODUCTION The Cyprus Pima Mine is located 20 miles southwest of Tucson, Arizona and about fifty miles north of the Mexican border. The Cyprus Pima orebody was discovered in 1950. Feasibility studies were begun in 1952 employing underground development. Economic studies showed open pit operations to be feasible and stripping of overburden was begun in late 1955. The first ore was reached in October of 1956. A 3,000 tpd (tons per day) concentrator was completed and began operation January 1, 1957. From these beginnings, Cyprus Pima Mining Company has expanded into a plant processing approximately 54,000 to 56,000 tpd. Four expansions were required to bring the plant up to its present capacity. Each expansion incorporated what had been learned in previous operation of the plant. The first expansion was completed in August of 1963 doubling design capacity to 6,000 tpd. In reality, because of softer than average ore, capacity was closer to 8,000 tpd. Expansion I1 was completed in July 1966 bringing design capacity to 18,000 tpd. Expansion I11 followed immediately. Completed in the summer of 1967, this expansion increased the design capacity to 30,000 tpd. The actual dry tonnage of this portion of the operation in 1974 averaged 38,400 tpd, again, primarily as the result of treating softer than average ore. The latest expansion (Expansion IV), completed in December 1971 and utilizing a semi-autogenous grinding circuit, is located in a separate building (Mill 11) approximately 200 yards southeast of the original mill (Mill I). Expansion IV was designed for 14,000 tpd, but after circuit modifications, averaged 16,500 tpd in 1974.

Jan 1, 1976

By J. J. Casey

This paper is one of a series of presentations organized by the Conference of American Society of Civil Engineers with the goal of making significant progress toward an equitable and effective allocation of risks in construction undertakings among the principal parties - owner, contractor and designer. The role I have been assigned is principally one of identification of risk while others will devote greater attention to the allocation of these risks and the contractual arrangements necessary to properly make these allocations. Construction projects are joint undertakings by parties who bring different skills and interests toward a common effort, much as this conference does. A project is not an adversary proceeding and does not benefit from establishment of an adversary mode, as our lawyer friends seek in the resolution of legal issues. Accordingly, I urge upon this Conference the adoption of two basic precepts and guidelines as the criteria for sharing of the risks inherent in construction undertakings toward achievement through mutual effort the common goal of a successful project completed in the shortest time and at the least overall cost. These precepts are: (1) that all risks are rightfully the owners unless transferred to or assumed by another party for a fair compensation; and (2) that the principle guideline in determining whether a risk should be so transferred should be whether the receiving party has both the competence to fairly assess the risk and the expertise necessary to control or minimize it. The sponsors of the conference have provided certain guidelines to the authors. There is, however, no constraint in expressing one's bias and I suspect that my contractor's outlook may be inherent in my comments. The guidelines have suggested that I indicate whether the risks identified are ones that can or should be shared or borne by one party alone. In doing so, I will attempt to follow the precepts I have recommended.

Jan 1, 1979

By T. M. Barton, M. Gauna, A. A. Campoli

Coal mine bumps, the violent failures of overstressed coal, present a safety hazard to miners when longwall mining is conducted in deep, bump-prone coal mines. Two different longwall gate entry systems were evaluated in a southern Appalachian coal mine located in the Pocahontas No. 3 coalbed under approximately 610 m (2000 ft) of overburden that included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design used a 24.4-m (80 ft) square abutment pillar, while the new design employed a 36.6-m x 54.9-m (120 ft x 180 ft) abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worst-case conditions increased effective bearing area 62%, with only a 9% increase in gate entry system width, and eliminated face bumps that were experienced with the original gate entry design.

Jan 1, 1993

By M. Hancer

The sign of the surface charge of selected potassium soluble salt minerals namely KClO4 , K2SO4 , KNO3, and KCl was determined from nonequilibrium electrophoresis measurements and found to be negative for each of the salt. Dodecylamine flotation of these salts revealed that the concentration of amine required for flotation increases in the order KClO4< K2SO4< KNO3<KCI. Precipitation of the amine collector colloid was not required for flotation of the oxyanion salts and in this case it appears that adsorption of the dodecylamine cation is sufficient to create the hydrophobic surface state. The order for flotation is explained in terms of surface hydration of these respective potassium salts based on contact angle measurements and FT Raman spectroscopic characterization of water structure.

Jan 1, 1999

By Boyd Eisenbraun, Dennis Murr, Milton Rojas

Approximately since 1925, the phenomena of grinding and classification of minerals with screens have been studied. In the U.S. iron ore mining operations located in the so-called “Mesabi Iron range,” magnetite processing plants have made progress in the application of high-frequency screens that have allowed them to process low-grade Taconite ores and successfully achieve the economic benefit of these minerals. In the particular case of magnetite minerals disseminated in the siliceous matrix, the main objective is to reduce the generation of particles called “middlings” with high silica contents. Commonly the primary challenge of the metallurgical task is to achieve high recoveries and iron concentrates with low impurities. To achieve this, several studies and industrial applications have shown success in this regard and not only in iron ores, but also in other minerals around the world. The study described in this paper attempts to describe some key aspects that helped develop an effective solution and list the benefits associated with this modern process design by using industry-proven technologies for minerals in Chile that have similar characteristics to the minerals of the iron belt in the United States.

Feb 1, 2025

By Y. S. Kim, A. Bailey

A feasibility seismic refraction and reflection field survey was conducted at the U. S. Borax Company open-pit mine, Boron, California by the writers during the weekend of March 13 and 14, 1976. This field survey was carried out as a preliminary investigation primarily for the purpose of evaluating and establishing the ability of such geophysical techniques to locate and outline the subsurface openings of the old room-and-pillar mining under the present open-pit. The value of such knowledge about the old underground workings is directly related to the safe and economical operation of the open-pit mine for the company. Although mine maps of the old underground workings are available at the mine, the extent of roof and wall cavings and the present condition of the old underground openings are unknown. Owen and Suhler (2) are the first investigators who used electromagnetic methods, Pulse-Echo System, and electric resistivity measurement to solve the problem without success. A few years later, Herzig and Owen (1) attempted to solve the problem with application of earth resistivity measurement method with unfavorable results. The U. S. Borax Company carried out an extensive study for slope failure problems of the open-pit with application of dipmeter measurements. However, the slope stability study was not correlated to the old underground openings lying under the present open-pit (3).

Jan 1, 1977

By Alan English

This paper reviews the process control systems used in early commercial pelletizing plants, traces the development of these systems into present day practice, and briefly outlines advanced automation concepts being considered for future installations. It deals specifically with controls for the balling circuit, pelletizing machines, and related material handling and combustion equipment. The importance of instruments for visual observation and data logging is discussed, and the potential use of computer control is evaluated.

Jan 1, 1965

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By E. Watkins, M. B. Daza

Although there have been great advances regarding the understanding of mine fires in underground mines in the last century, fires remain high risk incidents. During fire scenarios, many crucial decisions and actions can be made that greatly influence the outcomes of these scenarios. Underground worker decisions are mainly based on training and experience, which in some cases can be complemented with previous analysis of fire effects. In order to review the guidelines that should be taken into account for this kind of examination, a numerical analysis of effects produced by a shuttle car fire under five different ventilation conditions was carried out. The analysis provides some insightful recommendations for firefighting personnel such as time for direct attack and best attack position for first responders and fire brigade groups. Also, the most critical parameters for each scenario were determined. Finally, all results were systematically organized and a first approximation of a fire classification based on the tenability limits was provided for first responder and fire brigade groups. The methodology used in this study for the fire classification could allow for the most appropriate decisions by firefighting personnel increasing the probability to put fires out without compromising their health and safety. INTRODUCTION While there have been great advances regarding the causes of mine fires in underground mines in the last century “small fires have occurred and always will occur in underground mines” (Conti, Chasko, Wiehagen, & Lazzara, 2005). The response time and decisions made during an underground mine fire are critical elements that have direct influence on the event outcome. Mine fires can grow in size quickly causing catastrophic consequences, thus rapid and suitable response actions can result in the difference between an minor emergency situation and a disaster. Upon the confirmation of a fire, a decision must be made regarding whether to fight the fire or evacuate the mine. Even though all underground coal mines possess emergency response plans and firefighting personnel are highly trained, decisions can be complemented with previous numerical analyses. Such analyses could contribute with the knowledge of potential fire effects and consequently with fire preparedness in the mine. Preparedness in underground mines is an important element to reduce the probability of the negative consequences of a mine fire. The time elapsed between the detection of the fire and response in the early stage is a serious component since small fires can produce larger and more serious consequences. If a mine fire cannot be put out within the short time after discovery, the chance of getting the system back in balanced or the success of safely controlling and extinguishing a mine fire is reduced (Conti et al., 2005, Conti, Chasko, Wiehagen, & Lazzara, 2000, Trevits, Yuan, Teacoach, Valoski, & Urosek, 2009, Brake, 2013). As confirmed by Conti and others, if a mine fire cannot be controlled by direct firefighting methods the probability of extinguishing the fire, without sealing is greatly reduced (Conti et al., 2005). However, response actions such as direct extinguishment must be carried out without compromising the health and safety of the firefighting personnel (Kim, Lönnermark, & Ingason, 2010).

Jan 1, 2019

By Luis Fernandez-Deza, James Hawn, Dustin Mount, Jean-Marc Wehrli

The RiverRenew Tunnel System project in Alexandria, VA forms part of a CSO scheme aimed at reducing overflows of combined stormwater and sewage into the Potomac River during storm events. A major piece of the project is a 12-foot internal diameter tunnel of approximately 12,000 feet length lined with a single-pass precast concrete segmental liner and excavated by an Earth-Pressure Balanced Shield TBM. The tunnel lies between 120 to 140 feet below grade in the clays of the Upper Potomac Formation with occasional dips of more granular, saturated soils of the Terrace Formation and the Alluvium. The TBM is launched from a figure-8 configuration Pumping/Screening Shaft located within AlexRenew’s operational Water Resource Recovery Facility. This paper discusses the challenges encountered during the launch of the TBM in short mode within a highly congested site and from narrow deep shafts.

Jun 13, 2023

By B. T. Field

Pyroprocessing systems range from low temperature dryers to high temperature reactors. The materials and process requirements cover a broad spectrum. It is not the intent of this paper to do a detailed examination of individual processes and equipment, since that can be found in a multitude of other sources; rather it is the intent of this paper to examine the key process variables and offer empirical guidelines to assist in a user?s overall evaluation.

Jan 1, 1998