Search Documents

By J. W. Cooksley

Seismic methods provide an efficient and comprehensive approach to overburden studies pertinent to mining exploration and development, and to other mining and civil engineering problems such as rock mechanics, slope stability, and foundation engineering. For the purpose of defining geologic units and structural features, these methods are generally regarded as the most accurate, but most expensive, of the commonly-used geophysical exploration methods. Although the accuracy and cost of seismic work are generally affected adversely by rugged topography and complicated geologic conditions, it is in rough terrain and complex geology that seismic methods offer important advantages in overburden investigations. For example, to find the surface of rock underlying unconsolidated overburden at depths of approximately 200 feet, a 50-foot spacing of drill holes along the profile line would be required to yield a degree of resolution and accuracy similar to that obtained from a 50-foot spacing between seismic detectors along the same line. See Figure 1. In cases similar to that shown in Figure 1, a twelve-channel recording seismic system would be used. The main components of such a system would be: 1. detectors (commonly referred to as geophones) which convert the ground movement resulting from seismic waves into an electrical signal. 2. a multi-conductor cable which connects the seismic detectors to the amplifiers. 3. ampliiiers, amplify and filter the electrical signals . 4. oscillograph, records the amplified signal. 5. the blaster and firing line. A typical layout of the seismic spread and the components of the system Is shown in Figure 2.

Jan 1, 1968

By Håkan Stille, Kjeld Boye-Møller, Lars Lundström

BACKGROUND Forsmark Power Station is a nuclear power plant under construction at the Baltic abt 120 km north of Stockholm. Investigations on the Site were started in 1969. Areas were reserved for a maximum of 6 units of which the buildings for two of them, Unit 1 and 2, were nearly finished in 1976, when the investigation for Unit [3], here presented, was carried out, cf Fig. 1. [ ]

Jan 1, 1979

By C. J. Myers, D. L. McKinnon, A. A. Dasys

In 1988, the National Institute of Occupational Health and Safety (NIOSH) published an information bulletin stating that whole diesel exhaust should be considered a probable carcinogen. Since then, regulations across Canada and the United States (Mine Safety and Health Administration, MSHA) have looked at appropriate exposure limits for underground mine workers. In Canada, an interim standard of 1.5 mg/m3 Respirable Combustible Dust (RCD) has been adopted by some provinces and is being looked at by others. MSHA is considering levels as low as 0.5 mg/m3 soot. Golden Giant, being aware of regulatory developments, decided to look at means of reducing diesel particulate on thier large production machinery. This machinery (LHDs and haulage trucks) is powered by Detroit Diesel 71N Series engines and is used to produce 3000 tonnes of ore/day with a longhole mining technique. Having looked at the various control technologies, it was decided to evaluate the potential of using diesel particulate filters with a copper-based fuel additive for regeneration (the process by which collected particulate is burned off). This paper outlines the control technology used and the results of the field evaluation indicating the benefits to the underground mine worker.

Jan 1, 1993

By William K. Burriss

Computer technology was applied to solve three problems in the selling of certain industrial minerals to the glass and foundry industries. The computer solutions provide for better service to customers and have helped increase sales. II. Summary Electronic data processing techniques were applied: 1. To automatically and continuously "trace" rail car shipments of bentonite. 2. To aid our sales people in recommending to glass plant purchasing agents which of several possible feldspathic materials is the best value at any of about 100 glass plants and to give guidance on the amount of value difference. 3. To help in locating plant sites for three blending or pre-mixing stations to serve the foundry industry at minimum cost and with maximum tonnage and maximum profitability.

Jan 1, 1968

By J. H. White

It is hypothesized that the Hotelling Valuation Principle (HVP) can determine the value of developed gold reserves using simple methods and easily obtained data. This paper reports the results of an empirical test of this hypothesis. Using publicly available data from North American gold companies, we obtained data for V, R, p, and c and ran a simple linear regression using equation (1.1) as the definition of the dependent and explanatory variables. By examining the value of the coefficients of the resulting regression equation, we can draw conclusion as to whether or not the HVP can be confident1y used as an estimator of the value of developed gold reserves.

Jan 1, 1995

By R. H. Weiland

The dewatering of flocculated clay suspensions by compression in a centrifugal field has been investigated. The results are evaluated with regard to both direct applicability to centrifugal dewatering, in solid-bowl centrifuges for example, and indirect applications to gravity sedimentation systems. It is well known that sediment consolidation under gravity depends on structural characteristics such as permeability and on the "self-weight" of overlying sediment layers. An important objective of the study has been to evaluate the self-weight effect using centrifugal forces to simulate consolidation in deep sediments. In this way, small-scale laboratory tests can be used to predict the rates and limits of sediment compression in industrial systems such as thickeners and settling ponds. Experiments have been conducted in which the sediment mass and initial structure were maintained constant while the effective sediment weight was varied by centrifuging at different speeds. The effects of initial structure have also been studied using controlled variations in flocculation conditions.

Jan 1, 1993

By Dave G. Osborne

With the growing exportation of coal from North America to the Pacific Rim countries and Europe, has come an increasing awareness of the need to determine economically optimized amounts of incombustibles (ash and moisture contents) for the shipped product. Despite the fact that demand bas caused a steady improvement in selling price, particularly for thermal coals, growing production and transportation costs have compelled producers to keep a sharp eye open for ways and means of minimizing the latter since this probably represents the greatest single potential for making savings. Consequently the Coal Industry has become acutely aware of the economic ramifications of eliminating moisture in particular, thereby producing further saving in the cost of transportation of product from the mine to the consumer. There is, however, a lower limit to which dewatering or drying can be taken and this relates to dustiness which is a function of the characteristics of the coal and the methods used for handling and storage during trans-shipment. Overdrying can lead to serious dust losses and difficulties in handling particularly if the coal contains a large proportion of fines. The ways and means for achieving this "happy medium" of optimization in moisture removal are seemingly undergoing gradual modification largely assisted by the following factors. a) Improvement in effectiveness of coal dewatering and drying equipment. b) Improvement in operational availability and utilization of the equipment. c) The development of surfactants, polymer flocculants and other agents which in many cases can be almost tailor made to suit specific applications.

Jan 1, 1982

By Robert A. Haney, David J. Atchison, Kenneth G. Fields

Mining systems with greater than a 20-foot face advance (deep cut) have become popular due to their increased productivity and safety. The face dust collection system used in many of the mines employing the deep cut systems, incorporates a machine mounted dust collector with either a blowing or exhausting line brattice and a remote control operated continuous miner. In order to characterize and quantify the parameters used to control dust with these systems, the Dust Division conducted studies on four mining sections using continuous miners with deep cut mining systems. On each section, the dust control system incorporated line brattice with a machine mounted dust collector. The remote control made it possible for the continuous mining machine to advance further while permitting the operator to remain under supported roof and away from dust generated during mining. The purpose of these studies was to evaluate the effectiveness of deep cut mining systems using dust collectors to control respirable dust exposure. This paper summarizes the results of the studies conducted. At each mine face workers were sampled to determine their full-shift dust exposure. Additionally, fixed point dust samples were collected at various locations to determine relative concentrations of dust generated from mining. Air quantities were measured at each working place to determine the amount of air delivered to the face area. Evaluations were made by comparing worker exposures to respirable dust samples taken at appropriate locations upstream and downstream of the coal faced being mined. An estimate of the amount of the respirable dust being generated at the face during mining and the amount of respirable dust being removed by the dust collectors was made by balancing the air quantities and the dust concentrations immediately upstream and downstream of the coal face. Results of the studies showed that the dust control systems, were effective for controlling workers exposure to respirable dust. Dust collector efficiencies were determined to be approximately 85 percent. While the dust collectors were effective in removing respirable dust, the success of the systems with line brattice greater than twenty feet from the face, was dependent on the use of the remote control which permitted the continuous miner operator to remain out of the high concentration dust cloud in the working face. Dilution from intake air, combined with the dust collector efficiency, maintained exposure of other section workers below applicable standards.

Jan 1, 1991

By I. H. Warren

Hydrometallurgy has a well-known and established role in the production of manganese metal (1) and manganese compounds, including battery grade manganese dioxide (2). Also, several leaching processes have been developed and applied at various times for the recovery of manganese from low grade ores (3). Recently, interest in the hydrometallurgy of manganese has been stimulated by the problems presented in the processing of sea nodules (4). Fumes and dusts from the ferro-manganese furnaces also offer a potential field for the application of manganese leaching techniques (5). In treating low grade manganese ores a major requirement of the leaching process is that it should dissolve manganese from a mixture of manganese and iron oxides. The most selective reagent for this purpose is ammonium carbamate applied after preliminary pyrometallurgical reduction of the ore (6). Since soluble carbamate complexes of the postulated type (7) are formed by both manganous and ferrous, but by neither manganic nor ferric, ions, selectivety of manganese leaching is achieved by control of the reduction operation to yield, essentially MnO and Fe304? A potential improvement to this two step process would be to simultaneously reduce and selectively leach the manganese in one hydrometallurgical operation. This possibility has been experimentally studied and the results are described below. During the preliminary study of the stability of solutions of ammonium, ferrous and manganous carbamates at elevated temperatures, it was observed, contrary to the observation of Welsh (8) at lower temperatures, that

Jan 1, 1971

By Antoon W. van der Vooren, Colin R. Phillips

A comparison of analytical models used to describe deposition in the first generation of lung bifurcations is presented. In order to allow testing of the mathematical models, experimental data were obtained from radon daughter deposition in simplified lung bifurcations. The experimental data for particles deposited by diffusional mechanisms is best described by the assumption of a thin concentration boundary layer at the entrance of a right circular tube. Other more complex models do not accurately describe the deposition of submicron particles. The angle of bifurcation was found to have a minor effect on deposition.

Jan 1, 1981

By Raymond Mancha

"Conventional" coal dryers really do not exist. What we really mean to say is that there are many and varied kinds of coal dryers -- and the "air handling problem" is really the only portion of it which has been approached for solution by conventional methods. It now appears that these conventional methods need supplementing by some new, relatively unconventional apparatus. In order to approach this matter with mutual understanding, here is a quick survey of the coal drying art. Figure #1 shows a McNally Pittsburgh Pulso Dryer, In the McNally Pulso Dryer, the coal is fed-onto the screen by a rotary feeder assuring even distribution of the coal. As the coal travels forward due to the action of the screen, it is subjected to a controlled pulsating flow of hot gases. T ese originate below the deck and are directed up through the moving bed of coal. Fines sifting through the deck are dried in the hopper below the screen as they fall through the hot gases to an evacuation screw. The coal remaining on the screen is dried to the desired degree when it reaches the discharge end. At this point, it is directed down into the evacuation screw to combine with the fines, or it may be discharged as a separate product. As the coal travel down the screen, it is subjected to intermittent upward currents of hot gases. These first distend the bed allowing the gases to come into intimate contact with the coal particles for rapid and efficient heat transfer. Then, as the flow of gas is cut off, the bed settles and the extreme fines sift through the screen preventing their being carried away into the exhaust system.

Jan 1, 1958

By Joseph G. Wargo

The purpose of this paper is to investigate trends in exploration expenditures of a selected group of mining companies for the interval 1968 through 1971. The paper also compares these trends with other financial factors that are associated with various groups of companies and comments on the implications of these trends. Although a four-year interval is hardly enough time to establish a long-range set of trends from which operating rules can be derived, the fact that the four years selected are in the immediate past gives some sense of relevance to the matter of exploration expenditures at the present time and in the near future. The sample under study here consists of 21 mining companies. Of these, 19 are listed on the New York Stock Exchange and 2 are listed on the American Exchange. Twenty are American, one is Canadian. All are fundamentally "mining companies" in that they derive the bulk of their income from the extraction, sale, and at times, fabrication of metals from their own mines. This is in contrast to companies which have mineral exploration departments but derive the bulk of their revenues from sources other than mining; for example, from oil and gas sates, Also, no companies which can be considered strictly as exploration companies are included in this study. Although this definition held up fairly well when studying this list in 1968, the strict application of this definition became more difficult through the years up to the present time. In 1971, three or four of the companies were changing their character in that they were phasing out of the mining business, and either deriving their income or planning to derive a substantial part of their income from activities other than mining. A study of

Jan 1, 1973

By F. L. Wilke

Bong Mining Co. Ltd. in Liberia, West Africa, operates an iron ore open pit some 60 miles northeast of Monrovia. The production is at present about 40,000 t/d (metric tons/day) from which about 18,500 t/d concentrate with 65.5% Fe is produced. The ore waste ratio is about 1: 1.5 to 1:2. The technical layout and the equipment are very similar to those in many modern open-pit operations as described by Jacobs and Thomson (1967). As described by Lersch in detail (1966), the deposit is a very irregular one. The quality of the ore changes within very short distances with regard to both physical conditions (hardness) and chemical properties. Very soft and very hard ore as well as high-grade and low-grade ore are found adjacent to each other. In addition, there are enclosures of sterile rocks. For the purpose of identification and production scheduling, 12 different types of ore are distinguished.

Jan 1, 1979

By G. F. Revey

Most commercial explosives contain from 70% to 94% (by weight) ammonium nitrate. When some of the explosives end up in shot rock and ore, through either spillage or incomplete detonation, ammonia and nitrates can leach into the ground water. In recent years, state and federal regulators have applied more stringent water-quality standards, particularly at new mines and development projects. When mining conditions permit, bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice. ANFO is less costly than other explosives but it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. These approaches range from controlling explosive losses to treating the mine effluents. In this paper, controlling explosive losses is addressed For both packaged and bulk explosives, guidelines to limit losses during storage, handling and use are described in detail.

Jan 1, 1997

By Richard S. Mateer

The percent ash in a coal blend is equal to the weighted average of the ash contents of the component coals. If the raw coals differ in washability characteristics, the total yield may be maximized by washing the component coals to different quality levels. A mathematical basis for blend maximization is developed and a computer program is described The program determines the component weights that maximize the yield, while meeting an individual coal-quality specification. The procedure is directly applicable to linear parameters of grade quality such as percent ash, percent sulfur and the calorific value. A transformation of variables permits program execution to meet a sulfur-compliance specification. Blends may consist of any number of component coals.

Jan 1, 1997

By H. Nakazawa

Galvanic contact, occurring between electricall y conducting minerals in flotation pulps, may affect the nature of mineral surfaces and influence their floatabilities. Rest potential and galvanic current measurements were made on an electrode combination of pyrite and pyrrhotite under nitrogen, air and oxygen aeration conditions, and the results were correlated with their oxygen-consuming characteristics and flotation behaviors. The galvanic contact improved the floatability of pyrrhotite, but adversely affected that of pyrite. Auger electron spectroscopy, x-ray photoelectron spectroscopy and scanning electron microscopy indicated that the formation of hydroxide or oxide and sulfate species of iron on pyrrhotite decreased whereas that on pyrite increased when these minerals were held in contact. An electrochemical mechanism was proposed for the observed behaviors.

Jan 1, 1985

By William T. Barrett

It is said that Thales of Miletus, 600 B.C.,1 was aware of the attraction of lodestone toward iron and highly magnetic minerals. However, the birth of magnetic concentration followed shortly after the invention of the first electromagnet by Sturgeon in 1825. Sturgeon's magnet was described in the annals of electricity.2 The first attempts to concentrate minerals by the use of magnets date back to about 18473 but the first commercial drum-concentrator was apparently invented by R. Cook in 1849. Credit must also be given to the invention of P. Righter's machine in 1867,5 and to the highly successful Wenström separator devised in Sweden in 1883.8 Since the advent of these early separators there have been virtually hundreds of patents granted covering minor modifications of drum-type magnetic separators. The more important advances from a technological viewpoint have been the design of stable power supplies for d.c. magnets, the advent of ceramic permanent magnets which are now replacing electromagnets for the concentration of ferromagnetic minerals, and advances in general magnet and machine configurations.7 One of the problems facing both the designer and the user of magnetic separators is the evaluation of the body forces acting on particles in the magnetic field of the separator. Perhaps the most elegant method of evaluating the body force associated with a drum-type magnetic separator is that recently suggested by W. F. Brown.8 Brown measures the radial component of the field intensity one-half inch from the drum surface and fits a Fourier series in the angle about the drum axis (Figure 1). Once the coefficients of the series are known, it is then possible to calculate [ ]

Jan 1, 1970

By Courtney Black, Paul F. Ziemkiewicz, Eberhard Werner, Matthew Daly, Joseph J. Donovan, Jeff Frazier

Injection of alkaline waste-lime slurry was performed at a West Virginia surface coal mine site, to attempt neutralization of acid springs by an alkaline recharge method. Deep trenching (>5 m) using an excavator yielded the most effective injection into the aquifer. Water from two springs, 90 m from the deep trench, showed 70%-80% reduction in acidity in response to injection. Neutralization persisted >170 days after treatment, with pH between 5.1-5.7 and metal acidity from 25-60 mg/L. A minor fraction of lime introduced was consumed. The sustained neutralization is attributed to reaction of acid water with subsurface lime, entrained below the wafer table by macropore infiltration. Characteristics of groundwater transport are critical in determining recharge structure location.

Jan 1, 2000

By C. C. Hatch

As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer and winter of 1975 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses and to permit study of alternative circuit configurations if desired. This paper describes the simulation methodology employed and presents the results of a computer study of the secondary crushing plant (1).

Jan 1, 1979

By Bernard P, Lhoumaud E, Gunzburger Y, Conin M, De Santis F, Kinscher J

Seismic repeaters are commonly observed in natural fault zones dominated by slow aseismic motion. The corresponding seismic signal, characterized by highly similar wave forms, is usually interpreted as the repeating ruptures of locked asperities on fault planes (“patches of higher roughness”), loaded by a-seismically slipping areas (“creeping areas”) (Chen & Lapusta 2009; Bourouis & Bernard 2007). Only very few occurrences of seismic repeaters have been reported in underground mines, where these phenomena are rather unexpected since the stress state and the seismic wave propagation continuously evolve with the advancing excavation front (Kinscher et al., 2020). A recent study based on a local seismic network installed in the underground mine of Garpenberg, Sweden, has shown that seismic repeaters and multiplets represent the main part of the total released seismic energy (magnitude of seismic events: -2 < M <1, on moment magnitude scale), with some seismic families being active during several months to years. It is suggested that repeaters are linked to aseismic slip on pre-existing talc-filled fractures, induced by the excavation, and loading of asperities. These results imply that part of redistribution of stresses in the mine is due to aseismic slip, which might explain the observed distant and delayed seismicity.

Apr 26, 2022