Search Documents

By N. Patel

Many factors, from engineering and design to supply, installation, and operation affect the service lifespan of cast refractory linings. If a shortcoming occurs at any of these stages, the lining lifespan can be drastically reduced. Although not every aspect that can affect a cast refractory lining?s lifespan is outlined here, a few key points are highlighted, with an emphasis on the various installation parameters. Keywords cast linings, refractory lifespan, lining engineering and design, lining supply, lining installation, curing, dry-out.

Aug 1, 2013

By W. Gabryk

A large new underground platinum mining project required that all different mining options were investigated during an option study before proceeding to the prefeasibility stage of the project. The capital project team identified 21 different options requiring investigation. These options considered 10 different access methods and 4 different mining methods. Each of the 21 options required a mine design, a valid production schedule, and the associated economics in order to facilitate a comparison on project Net Present Value (NPV) and other metrics. The project sponsors required this work to be completed in 3 months and therefore the project team decided to adopt an object-oriented modelling approach as implemented by Cyest Corporation. This would allow all 21 options to be valuated within the tight time frame due to the generation and re-use of templates. Standard objects were configured into templates containing the mine layout, design, and scheduling logic. These templates could then be assembled into a model to represent the option being investigated. The adoption of rules-based design and production scheduling then allowed for the rapid generation of a valid production schedule for each option with different iterations of varying production ramp-up and mining efficiency assumptions. The activity-based operating costs, labour, and capital were also linked to the standard templates such as a half level or barrel, which were then replicated to represent the overall mine structure for each option under consideration. Using this approach for each option, a full production schedule was produced per mining activity, the operating costs were calculated using activity-based costing, an infrastructure capital expenditure estimate was determined, the development capital requirements costed, and an overall NPV determined. This options study was completed in an unprecedented 10 weeks and a recommendation was put through to the Business to take three of the options to the next study phase.

Jan 1, 2012

By J. R. Percival, L. Ip, M. D. Piggott, S. J. Neethling

Component wear due to particle-laden flow is a significant challenge in the minerals processing industry in the handling and transportation of abrasive mineral slurries. Studying wear through experimentation is time-consuming and expensive; therefore possessing the ability to accurately simulate, understand and predict wear in these complex environments is highly desirable. The ability to predict wear is important in both the design of equipment in order to maximise the performance over the wear life of the components, as well in minimising potentially costly and dangerous failures and unscheduled maintenance.. Particle-induced wear is a complex problem, requring an understanding of coupled fluid-solid motion, geometry deformation in response to fluid-solid behaviour, moving geometries and wear modelling. Although the literature demonstrates that rebounding particles and changes to surface profiles can have a significant effect on subsequent wear rates and patterns, the challenge of implementing a model to account for this effect in complex geometries has been addressed by only a few authors in the literature. This paper describes a new wear simulator, leveraging fluidity, an open-source, massively parallel, finite element based CFD simulator capable of unstructured adaptive meshing. The wear simulator includes the ability to model particle-laden flow using representative Lagrangian particles and dynamic remeshing of geometry in response to wear and component movement. These capabilities are demonstrated using wear and the associated dynamically deforming boundaries within a Coriolis tester arm, with the results comparing favourably with the experimentally observed wear patterns. Keywords: CFD, wear, two-phase flows, anisotropic mesh adaptivity, boundary deformation

Jan 1, 2020

There are presently no suitable underground mine production scheduling optimisation models available for application to sublevel stope mining. Scheduling underground production for maximum return is therefore still a manual process, which generally involves scheduling production from the next available highest cash flow stope within the operational constraints of the project. In most mining operations, the scheduling problem is too large and complex to guarantee truly optimal results through manual scheduling. This paper reviews some general optimisation studies that have been proposed for underground hard rock mining. Furthermore, an example of a mixed integer programming model is presented for a small conceptual sublevel stoping operation. Comparative results of a schedule generated by a mixed integer programming (MIP) production scheduling model and a manually generated model on a nine stope example is presented. Results indicate that the potential benefits of the MIP production scheduling model for the purpose of maximising NPV are significant. Finally, a new constraint was formulated to limit multiple exposures of fill masses for use in an existing MIP production scheduling model. Testing of the formulation took place on the central stope of the nine stope example, which showed that the formulation performed its task without breaking other operational constraints.

Jan 1, 2007

By R. C. More O’Ferrall

The author mentions some of the problems he has encountered, together with their solutions. These include the stoping of isolated pillars, the reduction of the size of shaft pillars, the stoping of a new horizon above or below a horizon that has already been stoped out, and the mining of thick bands of reef left behind in the footwall or hanging wall.

Jan 1, 1981

By J. E. Dickinson, J. L. Sutherland, J. Zhou, M. J. Cole, K. P. Galvin

Interest in early gangue rejection has grown substantially in the minerals industry to reduce energy and water consumption arising from excessive comminution. Recent developments in coarse-particle flotation have proven successful by promoting a quiescent hydrodynamic environment to limit particlebubble detachment and by helping to convey more buoyant particles to the overflow. Current approaches also benefit from upstream classification to remove the finer particles ahead of the coarse-particle flotation. In this study, coarse-particle flotation was investigated experimentally using a novel hybrid gravity-flotation system called CoarseAIR™ that exploits the hydrodynamic advantages of the Reflux® Classifier. The system consists of a lower fluidised bed housing, with a system of inclined channels above. The inclined channels enhance the segregation and hence rejection of intermediate through to relatively coarse particles containing little or no surface liberation. This approach overcomes the need for pre-classification, while offering strong transport of coarse particles made buoyant through their attachment to air bubbles. The paper explores the strong relationship between the solids transport to the overflow and the input gas flux, showing firstly the potential for significant mass rejection at the relatively low gas fluxes, and robust performance in terms of recovery across the full range of gas fluxes. Keywords: Flotation, inclined channels, coarse particle flotation, Reflux Classifier

Jan 1, 2020

By A. W. Bryson, J. D. le Roux, B. D. Young

Several rate models for the adsorption of gold cyanide from aqueous solution onto activated carbon are given in the literature. The purpose of this study is to critically examine their ability to simulate the adsorption process over a wide range of conditions. An account is given of a comprehensive set of experimental work on the kinetics of gold adsorption onto a coconut shell- based activated carbon. Equilibrium isotherms were also determined. It is concluded that the homogeneous surface-diffusion model fits the experimental data reasonably well and provides a good balance between simplicity and descriptive accuracy. The model contains two parameters: the extra-particle mass-transfer coefficient and an effective intraparticle surface-diffusion coefficient. Both can be evaluated readily from simple adsorption experiments.

Jan 1, 1991

By E. T. Boome, A. C. Schmidt

P .E.R. T. and how P .E.R. T. techniques can be used in modern mine management by E. T. Boome and A. C. Schmidt Published in the Journal, December 1972 DISCUSSION A. E.W. FLETCHER A.c.S.A.* In making this contribution to the authors paper, I should first like to congratulate them on the clear and yet detailed way in which they have illustrated their subject. I should also like this contribution to be linked with Mr Hazell's paper "Mine Management by Objectives".

By Marthie Kotze, Jacolien Wyethe, Bert Van Hege, Richard Bell

Base metal refinery effluent streams may contain low metal concentrations that cannot be recovered by precipitation. Although the concentration is low, the total mass of unrecovered metal can have significant value because of the volumes of effluent generated. This metal may be recovered with high efficiency using selective ion exchange resins. Three process schemes are considered, viz., fixed bed column ion exchange, continuous countercurrent resin-in pulp, and continuous carousel resin-in-pulp. Each of these has different requirements in terms of equipment, resin inventory, capital and operating costs, and different limitations on feed conditions. Bateman and Mintek recently developed a model which allows an upfront economical evaluation of ion exchange options. The model evaluates the capital and operating costs for each process scheme for various base metals. This provides a general guideline for selecting the appropriate process arrangement for a given process stream.

Jan 1, 2005

By P. Jordan

The practice of ilmenite smelting in electric arc furnaces has been researched and published over the last few decades. An issue that has not been addressed is the understanding of the properties of ilmenite smelting reductants, and linking these properties to the subsequent smelting behaviour in the furnace. The reduction mechanism of ilmenite smelting is not fully understood, but it is believed that the Boudouard reaction plays a role. This paper investigates the behaviour of a number of reductants when reacted with CO2 at different temperatures. Keywords Boudouard reaction, carbon reactivity, reductants, ilmenite smelting.

Jan 1, 2011

By D. D. Marsden, L. E. Kun

Although a regulation is in force that all water used underground shall be free of bacterial contamination, in practice it is often very difficult to accomplish this. The standard method of disinfection m South African mines IS treatment with calcium hypochlorite, although liquid sodium hypochlorite is used at a few sites. Primarily because the process depends on human control for the addition of the hypochlorite and the regulation of its now, it is frequently found difficult to disinfect mine water adequately and continuously. In many marine environments, chlorine generated by the electrolysis of seawater in its passage through an electric cell is used for disinfection. The generation procedure is continuous and needs no human control except for occasional checking of the equipment. This paper describes the successful implementation of the process, suitably .modified, .at four underground sites. After severe scaling problems had been overcome, a procedure resulted that chlorinates considerably more effectively than the previous system (dosing with calcium hypochlorite), and that has a lower amortized operating cost.

Jan 1, 1981

By B. M. Van Vliet

SYNOPSIS This paper outlines the principles involved in the regeneration of activated carbon for renewed use in the recovery of precious metals or the purification of water. While chemical methods are effective in restoring the activity of spent activated carbon containing only single or defined adsorbates, thermal methods have to be used when the spent carbon is loaded with a heterogeneous mixture of adsorbates such as those normally present in industrial process streams or effluents. The steps involved in thermal regeneration are described, together with the operating conditions that can be controlled to give the required degree of activation. Finally, an account is given of the structural changes that occur in a new or spent activated carbon during thermal treatment.

Jan 1, 1991

By A E. Paterson

General aluminium corrosion charts based on 1100 alloy listing product and temperature have been developed by AFSA, mainly from available sources. The categories of corrosion expectation are fairly wide. As a result the charts are more useful in indicating what is not suited as distinct from what is. The question of how to develop useful information is assessed. Having discarded improbable options one is left with the need to refine the possible. Within each alloy group corrosion potential differs. From an engineering application point of view, the corrosion resisting marine alloys, the 5xxx series show increasing corrosion as the percentage of Magnesium increases. An important issue is that as the welding filler used for 5xxx series is Mg rich (to avoid hot cracking), the filler is likely to show the weakest resistance. In addition, when subjected to fatigue loading, the preference for critical joints is to dress the joint to the level of the base material. Overheating of the weld extends the HAZ zone and weakens the material as Mg moves to the grain boundaries. Indicator chart refinement approaches suited to aluminium use in commercial transport are discussed.

Jan 1, 2006

By Yuandong Qiao, Erdong Li, Chao Lv, Junjian Ye

The gas-based CO reduction of Panzhihua vanadium titanomagnetite concentrate from 1100°C- 1250°C was investigated in this paper. The reduction degree increased with increasing temperature and increasing reduction time. At a temperature of 1250°C and a reduction time of 20 minutes, the metallisation degree reached 92%. The iron-titanium oxide phase transformation during reduction process was Fe2.75Ti0.25O5→Fe2.5Ti0.5O4→FeTiO3→FeTi2O5 according to the X-ray diffraction analysis. The SEM and map scan by energy spectrum of results of reduced samples at different temperatures indicated that the metallic iron particle size increased gradually as the reduction temperature increased. These results can serve as a reference for the reduction of vanadium titanomagnetite by CO. Keywords: Vanadium titanomagnetite concentrate, CO reduction, phase transformation, reaction mechanism

Jan 1, 2020

By J Taguta, B. McFadzean, P. E. Ngoepe, M. G. Mulaudzi

Computational modelling methods and isothermal titration calorimetry (ITC) were employed to investigate the interaction of a pyrite surface with thiol collectors. Modelling work was conducted in the presence and absence of water. Microcalorimetry was employed to investigate the resultant energy of interaction pyrite as a result of mineral-collector interactions. Sodium ethyl xanthate (SEX), diethyldithiocarbamate (DTC) and diethyl dithiophosphate (DTP) were investigated in this study. The results showed that the calculated surface energies and morphologies for FeS2 showed that (100) and (111) are the most stable surfaces. The morphology also indicated the appearance of the (100) and (111) surface facets and no presence of others. The calculated adsorption energies between thiol collectors and the pyrite surface were always more exothermic than the experimentally determined ones. When comparing different ligand types with the same alkyl chain length, the heat of adsorption of diethyl-DTC was greater than that of ethyl xanthate and diethyl-DTP for pyrite. Experimentally, the diethyl DTP barely adsorbed onto the pyrite surface and this may be due to a different mechanism of action. In computational calculations, water adsorption was found to reduce the reactivity of the Fe atom for the interaction with thiol collectors, and bring the adsorption energies closer to the magnitude of the experimental values. Keywords: Computational modelling, microcalorimetry, experimental and thiol collectors, adsorption energies

Jan 1, 2020

By L. S. Belyayeva, A. S. Chumak, N. N. Boyko, A. V. Bondarenko

Analysis of results of many years concerned study of the fire hazard parameters of the material of the mine conveyor belts come in for use at the mines of the Ukraine in 1984-2002 that was carried out in the laboratories of the Scientific-Research Institute of Mine-Rescue Work is adduced in the paper. The basic tendencies on raising the fire safety of the conveyor belts that are retraced in their world production are shown.

Jan 1, 2003

By S. W. Jacobsz, E. P. Kearsley, N. K. Schoeman

A physical modelling approach was adopted to simulate the process of cave mining propagation at various horizontal to vertical stress state ratios, and image data was captured and used to characterize the resulting failure mechanisms. Image processing was integrated into the study to determine minor principal strains in models to identify where critical extensional strains had been exceeded relative to crack propagation. The study exhibited a scale factor magnitude of 119 using a calculated critical extensional strain value of 0.014% for the modelling material used. It was perceived that cave propagation occurred through successive parallel extensional ‘fracture bands’ in all cases, as noticed in models of prior studies, deviating from that described by the Duplancic model. Cracks tended to bisect regions of minor principal strain equal to the critical extensional strain, which suggests ‘fracture banding’ is an acceptable failure mode for brittle, rock-like materials. Moreover, it was found that models with lower horizontal to vertical stress ratios (K ratios) showed a greater degree of vertical development of the caving mechanism (at similar vertical stresses), while the vertical extent of the cave was suppressed in models with higher K ratios. Models subjected to larger vertical stresses experienced slower cave formation in latter time-steps. These models exhibited larger two-dimensional caved perimeters and areas, respectively.

Nov 30, 2022

By K. G. Lomberg

The integration of various highly sophisticated IT applications has been implemented at Bafokeng Rasimone Platinum Mine, a new platinum mine in the Anglo Platinum Group. This system is required to assist with compiling the necessary geological and grade information together with safety, environmental, ventilation, rock engineering and logistical constraints, to allow the design of the appropriate mining layout, to schedule this design, provide the necessary output for technical review and costing as well as budgeting to allow medium- and long-term business planning. In addition the production management and short-term planning needs must be met. This includes the plotting of all underground and surface infrastructure and excavations, giving the necessary mining and best cut instructions, daily production management, ore reserve and grade management as well as assisting with budgetary management. In addition all safety, health, environment and risk assessment requirements and legal requirements have to be met. The system at Bafokeng Rasimone Platinum Mine has met these criteria. Keywords: Platinum, Bushveld Complex, Mine Planning, Production Management

Jan 1, 2003

By W. F. Heinz

The efficient and effective handling and logistics of materials for underground support is an important part of mine mechanization and automation. Support systems based on backfill material or grout slurries and pastes transported underground through pipelines (ranges) lend themselves to a large degree of mechanization. In contrast the installation of conventional support systems such as props, timber packs, brick packs etc., requires more handling and hence is labour intensive and more costly. RODIO/ROSOND has developed and improved significantly its high density slurry/low density paste conveyance system on surface and underground during recent years. The surface batching and pumping stations are computer controlled and operate with a minimum labour complement. The RODIO/ROSOND grout pack support system has some unique features such as the use of relay stations, which result in the following distinct advantages and benefits to mining operations: • No interference with shaft operations • No grout ranges under high pressure in shaft • Efficient reticulation from underground relay stations • Low capital cost • Better control of quality of materials (high density slurry/low density paste) placed • Proximity of the working place to the relay station facilitates control of installation. These specific characteristics of RODIO/ROSOND’s grout pack support system have resulted in more economical support for several mines in South Africa and Australia.

Sep 1, 2001

By M. H. Tyeb, C. Banerjee, A. K. Majumder

The primary requirement from a hydrocyclone is the classification of the feed solid particles. Particle classification occurs inside a hydrocyclone by virtue of the relative radial distribution of the suspended particles, based on their size and specific gravity. The particle classification behaviour in a hydrocyclone is experimentally studied in this paper. The phenomenological features of the air core at different feed solid concentrations and the distribution of the solid concentrations in the hydrocyclone are also analysed by the theoretical study of flow features in a steady Rankine vortex. Semi-empirical models for predicting the hydrocyclone performance in terms of flow split ratio, and cut size have been developed using the background knowledge of convoluted hydrodynamics. In addition, to validate the classification performance of a smaller diameter hydrocyclone, the potential of the present model is extended for envisaging the same for larger diameter hydrocyclones. A comparison between the model predicted values and the measurement data shows a good match. Keywords: Hydrocyclone, classification, Rankine-vortex, air core, modelling

Jan 1, 2020