Search Documents

By J J. McEwan

Silver tarnishes readily in common atmospheres and is accelerated in humid atmospheres. Tarnish is the formation of silver sulphide on the surface of silver when it is exposed to a wide range of sulphur-containing atmospheres. Tarnish is unattractive and highly undesirable, and can be removed either with a silver polish or a chemical dip. Dips are generally only recommended when heavy black tarnish cannot be removed with a polish, and care must be taken during cleaning because these can contain aggressive chemicals and give off hazardous and unpleasant smelling fumes. Polishes work best for large areas of plain undecorated silver, and form part of a regular cleaning programme. Some polishes contain chemicals that inhibit tarnishing, but these generally only have a short life. Several methods have been developed to reduce tarnish formation on Silver; these include alloying, surface treatment, and coatings. The authors evaluated a range of self-assembled monolayer (SAM) surface treatments and coatings in earlier research. Four treatments/coatings increased the time to noticeable tarnish by more than ten fold, and the results were reported at the International Corrosion Congress (ICC) in 2005, and at the Mint Directors Conference (MDC) in 2006. SAM treatment using 95% 1-hexadecanethiol (C16H34S) was found to give good anti-tarnish performance and showed potential for the commercial treatment of Sterling silver. Therefore research was performed to optimise the methods of application of this type of coating to provide an easier, faster, and more-user friendly technique to provide an anti-tarnish treatment. Keywords: silver, tarnish resistant coatings.

Jan 1, 2006

By G. van Hout, D. Rahal

Caving is a mass mining method that is normally applied to large, low grade orebodies because of its low production cost and high capacity. However, equipment breakdown and poor draw management can cause mining costs to exceed that of all other mining methods. One way to minimize the effect of disruptions in the mining cycle is to use Mixed Integer Linear Programming (MILP) for long-term scheduling. This paper describes a MILP goal program which has the dual objectives of minimizing deviation from the ideal draw profile while achieving a production target. Schedule optimization is performed using a life of mine approach in which all production periods are optimized simultaneously. The underlying assumption being that material mixing in the short-term (between monthly optimization cycles) has a minimal effect on the long-term state of the panel. Schedule optimization is carried out using six general constraint types to model and control production. The constraint types define: deviation from ideal practice, panel state, material flow conservation, production quality, material flow capacity and production control. These constraints define production targets and drive production toward the ideal profile while maintaining correct mining practice. Application of the model using production scheduling data for a De Beers kimberlite mine. It is shown how different production control constraints regulate production from individual drawpoints as well as recovery of the ideal panel profile by implementing an optimised draw schedule.

Jan 1, 2003

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By M. C. Bhulose

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The purpose of this project was to identify constraints that could occur in the current sub-decline shaft at Turffontein Shaft should an increase in production take place. Particular attention was to be paid to the transportation of men and materials and to the broken rock and ventilation capacity of the shaft. This project is an in-depth evaluation of the logistic capacity of the sub-decline system at Turffontein Shaft in order to determine by how much production can be increased in this area to replace tonnages from the vertical shaft area, where ore reserves are rapidly becoming depleted.

Jan 1, 2004

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By B. Andresen, S. T. Johansen, H. Tveit, S. Grådahl, B. Ravary

The Norwegian ferroalloy industry has high ambitions regarding environmental standards. Basic research work has been performed to improve the fundamental understanding of ferroalloy processes and the environ-mental aspects. This paper will present work dealing with the understanding of formation and control of NOx, PAH and dioxins. During this work various techniques and methods have been applied, such as comprehensive industrial measurements, laboratory experiments, model development and application of Computational Fluid Dynamics (CFD). The main goal has been to reduce the environmental impact of ferroalloy plants, by means of improving the combustion processes done by introducing new charging routines and optimized furnace operations, instead of installing expensive gas treatment systems. The Norwegian obligations in accordance with the Gothenburg protocol are to reduce the NOx emissions by 30%, compared with the 1990 level within 2010. Measures developed in this work have resulted in 40-60%reduction in NOx emission, and major reductions in PAH and dioxins for ferrosilicon and silicon metal plants. This has been achieved by introducing semi continuous charging and improved furnace operations. Semi continuous charging and optimized furnace operations are shown to reduce the blowing activity (i.e. emission of large quantity of SiO over the charge by direct channelling from the crater zone). It also reduces variation in off-gas temperature and dust production. To understand the processes and to achieve our results we have used online equipment, with fast sample rates and response times, to measure the off-gas compositions and temperatures. Most of the measuring techniques used are based upon optical principles making use of the absorption- and emission spectrum of the gases. In addition a new prototype instrument is developed for continuous measurement of off-gas characteristics, total dust amount and off-gas temperature. The presented work is a result of a long term co-operation research and development teamwork, between the industry and the research community, and has improved both the process and reduced the emissions. The work has introduced new process design and operation standards, and has resulted in ferroalloy production with better environmental standards.

Jan 1, 2007

By I. J. Barker

Keywords: Submerged-arc furnace, plasma furnace, d.c. furnace, scale up, Søderberg electrodes, smart grid, demand side management, load shedding This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferro-alloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase a.c. electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become a more complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to get cheaper power from the organisations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of d.c. power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

The paper provides a brief review of a multivariate uniform conditioning and a localized multivariate uniform conditioning (LMUC) technique, and presents a production reconciliation case study based on a porphyry copper-gold deposit in Peru. The reconciliation study compares the longterm LMUC mineral resources model (typical of new mining projects, which are invariably based on drilling data on a relatively large grid) to the corresponding production blast-hole grade control model, as well as the final plant production.

Jan 1, 2014

By P. Lenegan, R. Masethe, R. I. L. Ferreira

Underground mining in high rock-stress environments can induce unanticipated dynamic rockmass deformation, posing a serious risk to the workforce. Data collected by seismic networks are imperative for the design-as-you-mine process. Often an inappropriate assessment of the seismic hazard is done when unnecessary data are included in analytical techniques, particularly short-term time frames. Depending on the methodology or application of data analysis and interpretation, some of the information may not be relevant and even detract from the objective. By using the spatial event clusters associated with active workplaces to define the shape and size of the polygons for data selection for subsequent analysis, a problematic subjective component can be eliminated. The mining of tabular reefs in South Africa, be they gold- or platinum group metals, is very extensive, and underground workplaces are often widespread. Production stoppages are very costly, especially for marginal mines, so there is just cause not to evacuate an entire operation’s workforce following the occurrence of a large mining-induced seismic event. A rationale based on the damaging peak particle velocities (PPV) of the past seismicity can exclude the unaffected underground personnel and allow a quick orderly withdrawal where required. Micro-deformation may precede rockbursting, which can occur on-shift close to the workface. A mine-wide array of geophones suitable for the accurate location and analysis of seismicity may not be able to detect these higher-frequency emissions. Inexpensive but fit-for-purpose accelerometers, providing real-time, continuous measurement of acoustic rockmass deformation near the workplace, integrated through underground and surface communications networks, are shown to record ‘rock-talk’, clearly distinguishable from the instrument background noise, which can be in the order of hours leading up to an imminent damaging seismic event.

Jan 12, 2025

By T. O. Hagan

Analyses of accident records show that a better understanding of very basic strata control principles and practices, by production personnel, will improve worker safety. Workers, lack of knowledge, with respect to aspects of strata control, increases their exposure to such strata control risks. The primary objective of the Safety in Mines Research Advisory Committee (SIMRAC) project 02 02 07 was to develop tools for the transfer of strata control knowledge. Four such tools were developed, three of which focused on illiterate underground mine team members who are not yet able to take advantage of the Mining Qualifications Authority (MQA) learning process (see project outcomes 2, 3 and 4 below). The tools were designed to equip these workers with sufficient knowledge and ability to work safely underground until such time as they can take advantage of the MQA system. Project outcomes: 1 A four-minute video using animation to illustrate the causes and prevention of falls of roof in South African collieries. 2 Software to demonstrate the capability of reconstructing, interactively, accident scenes and actions that have taken place underground in stopes. 3 A strata control bridging course for illiterate mine team workers. 4 Small-scale wooden models that will be used to design life-size mock-up facilities to assist with the above mentioned bridging course. 5 Workshops and presentations to demonstrate the outcomes 1to 4 above.

Jan 1, 2005

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

By D. Strachan

Installation of support in known poor ground intersections during reaming operations requires rapid access to stabilize the shaft wall and thus to prevent the loss of the shaft through scaling. This is especially relevant to shafts of long dimension where the duration from time of exposure to time of support installation is lengthy This paper deals with the innovative methodology employed at Harmony?s No. 8 Shaft 17/24 level sub ventilation shaft to rapidly support a shale intersection between 23 and 24 Level by employing a single deck stage suspended from the reamer head by means of Skyjack winches.

Jan 1, 2009

By J. Bakken, M. Th. Jonsson, G. Sævarsdottir

A typical three-phase submerged-arc furnace for production of silicon metal and ferrosilicon has arc currents ~100 kA, phase voltages ~100 V and total furnace power ~10 - 60 MW. The arcs burn in gas filled cavities or "craters", where the main atomic components of the plasma mixture are silicon, oxygen and carbon. Two quite different simulation models for high-current AC arcs have been developed: the simple Channel Arc Model (CAM), and the more sophisticated Magneto-Fluid-Dynamic Model (MFD). These models have been described extensively and results reported at INFACON-8 and INFACON-9, respectively. The coupling between the arcs and the AC power source is described by a complete three-phase Electric Circuit Model. Recent numerical modelling studies of industrial AC arcs show that the boundary conditions at the cathode and anode are critical for the simulation results. A novel Cathode/Anode Sub-Model for high-current AC arcs that treats both cathode and anode indicates a completely different cathode behaviour than previously assumed. A cathode spot which serves a high-current electric arc is shown to be dominated by the energy impact from the arc. This leads to lower cathode fall voltage than obtained from previously developed models. The anode fall voltage is negative, as the main function of the potential barrier is to repel plasma electrons. The cathode spot is diffuse in the sense that the arc in fact contracts away from the cathode. Simulation results are compared to measurements on both industrial furnaces and smaller scale pilot furnaces. An important conclusion, supported by our arc studies, is that the arc length in silicon metal and ferrosilicon furnaces does not exceed 15 cm and the arc may burn anywhere on the electrode, not necessarily beneath the electrode tip.

Jan 1, 2004

By S. L. Bell

Most Australian longwall coal mines are currently working coal faces up to nine kilometres from the surface. In the event of a mine emergency walking this sort of distance wearing breathing apparatus becomes very difficult if not impossible. Self-rescue continues to remain the focus of mines rescue in Australian coal mines and this paper describes a vehicle modification which will improve the chances of a miner rescuing himself. Existing mine personnel transport vehicles are not designed to operate in some types of atmospheres that may be present following a mine fire or explosion event. An Australian Coal Association Research program (ACARP) funded research project recently completed in Australia has developed a specification for a vehicle that is able to operate safely in some types of post emergency atmospheres. During the course of this investigation, diesel and electric vehicles were examined prior to making a final decision on vehicle suitability. Based on the fact that there are already some 1500 diesel vehicles in use in underground coal mines in Australia it was decided that modifications to existing diesel engines would be the best option. This presentation will outline the proposed specification for the vehicle and the reasons behind the decisions that were made with respect to the specification.

Jan 1, 2003

By A. D. Pienaar

The aqueous chemistry of niobium and tantalum compounds with hydrofluoric acid is a mature field of investigation. In contrast, very little attention has been paid to reactions of these compounds in non-aqueous environments. Similarly, reactions of elemental fluorine with niobium and tantalum compounds have received little more than cursory attention in literature. This work discusses the isothermal reaction kinetics derived from thermogravimetry, using a less redundant approach than is currently the standard. We also discuss the most likely kinetic models for this reaction.

Jan 1, 2012

By J. M. Galera, M. D. Rodriguez, V. Pozo, S. Cooper

"Cobre Las Cruces mine extracts copper minerals from a VMS deposit located in the well-known Iberian Pyrite Belt (IPB). As an open pit, it is distinguished geologically from other IPB mines by the presence of around 150 m of Tertiary soft marls, known locally as the Guadalquivir Blue Marls, followed by a regionally important aquifer. Below the marls and aquifer the mineralization is hosted by rocks typical of the Palaeozoic within the IPB, comprising gossan, tuffs, slates, and sulphides.This combination of a substantially soft rock and more competent, older (but still occasionally problematic) Palaeozoic lithologies constitutes a unique geological framework and presents substantial challenges in maintenance of slope stability, and therefore operational safety, at the mine site. This paper describes the fundamental design, excavation, and monitoring measures implemented at the mine to maintain safe production, and the lessons learnt during the mine development. IntroductionAs a modern Spanish mine, Las Cruces is committed to the use of best available technology and practices with the aim of guaranteeing the production of ore in a safe environment. From a practical perspective, this implies the realization of a high quality pit design, ongoing geotechnical mapping of exposed slopes to ensure conformity with design, and use of leading geotechnical surveillance technology to complement visual observations. The focus of this article is to illustrate how, at a mine site with potentially problematic soil/rock conditions, multiple advanced techniques employed from design stage analysis through to final pit configuration and vigilance, were combined to achieve an overall control of the ground conditions. In Figure 1 the layout of the pit is shown, illustrating development at the beginning of 2015."

Jul 1, 2019

By X. Q. Cao, D. S. Zhang, L. Q. Ma

To solve the support stability control problem for a coal face with large angles along both strike and dip (CLSD), the ’support-surrounding rock’ mechanical model has been developed, which takes into account the impact of the dip angle of the seam on the stability of the support in the strike direction. The mechanical relationships of the critical topple angle and critical slip angle of the support along the strike of the coal face with large dip angle and the support height, support resistance, friction coefficient, and other factors have been derived through the mechanical analysis of support stability in the strike direction of CLSDs in the free state, the operating state, and the special state. The research findings were applied to a fully mechanized CLSD in Xinji Coal Mine. The maximum underhand angle and overhand angle in strike are 42° and 25° respectively, and the maximum dip is 39°. It is calculated that during underhand mining and overhand mining, the critical support resistances for avoiding support toppling are 3723 kN and 1714 kN respectively, and the critical support resistances for avoiding slipping of the support are 7405 kN and 6606 kN respectively. Thus, the selection of type ZZ7600/18/38 hydraulic roof support for the coal face is justified. Measures to prevent sliding of the support and the installation of a limiting stop maintain the support runs in good condition and ensure safe and efficient mining of CLSD.

Jan 1, 2015

By T. J. Goff

Keywords: accurate control, matte level, smelting operations, process control, tapping, sounding bar, electromagnetic measurement [ ] Accurate control of matte levels during primary matte smelting operations is desirable in order to improve process decision-making. High matte levels in the vessel could have to disastrous consequences, particularly in the new generation of intensive smelting furnace with deep-cooled copper coolers. Knowing when to commence tapping and a better understanding of melt times can only be improved if the furnace levels are monitored correctly. At Lonmin Marikana Smelter Division it has long been understood that the matte level information being provided by the manual sounding bar is only as good as the operators? following of measurement procedure, their skill in assessing what the sounding bar is displaying, and their individual interpretation of what they are looking at. This paper sets out to show how this problem was identified as an area of major concern to the plant, how a solution was sought and how an electromagnetic measurement system was installed as an alternative measurement to the matte sounding bar system. Other areas discussed in the paper are the difficulties to be overcome when first installing new equipment and how these teething problems were solved by close co-operation between Lonmin and equipment suppliers, which led to some design modifications to the delivery system. In conclusion the paper discusses the results between the electromagnetic measurement and the manual sounding measurement and how best to integrate the generated data into the plant?s process control system for improved decision making.

Jan 1, 2011

By R. Dippenaar

The emergence of new steel grades is largely driven by the need to produce high quality steel at a competitive price. The principal aims are to attain ultra-high purity, (especially low interstitial elements) and ultra-cleanliness (by the control of the inclusion content and size). Whereas the steel used to build the Titanic contained 650 ppm sulphur, resulting in MnS stringer-inclusions 25 mm in length, modern quality requirements for arctic pipelines would only allow 10 ppm of sulphur and inclusions in ball-bearing steels must be smaller than 5µm. Most developments are aimed at hot-metal treatment before refining and ladle treatment after decarburisation. Because ferroalloys are added during or after the refining step, it is the secondary (ladle) refining production technologies that are of specific interest to the ferroalloy producer. Through ladle treatment, hydrogen and nitrogen contents are reduced, ultra-low levels of solute impurities are attained and the shapes as well as the composition of inclusions are modified. Steelmakers are concerned about the cost effectiveness of the use of ferroalloys such as consistent product analysis and delivery, improved financing arrangements and technical support. Minimal variation in product sizing is vital because it impacts on handling problems and because particle size determines the rate of particle dissolution. The required ferroalloy product quality depends on the specific use but in general sulphur, phosphorous and nitrogen contents are of concern. Apart from the presence of trace and impurity elements, ferroalloys also contain inclusions. For example, ferromanganese may contain MnO-MnS-SiO2 inclusions while high-carbon ferro-chrome may contain different kinds of Cr-Mn-spinels. The presence of these impurities and inclusions has a significant impact on steel production techniques and cost and hence, on the selection and use of ferroalloys. The interrelationship between ferroalloy quality and steel production technology is plant and product specific and hence, effective communication between ferroalloy suppliers and steel producers is essential.

Jan 1, 2004

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006