Search Documents

By S. J. Page, W. E. Wallace, P. Bolsaitis, D. Eppelsheimer, M. J. Keane, J. Poston, J. Harrison

"Respirable-sized dust particles from a clay mine and mill were examined for aluminium and silicon content by scanning electron microscopy-energy dispersive X-ray analysis at incident electron energies of 5--20 keV. Most of the high silica content particles, those which had a silicon to silicon plus aluminium signal fraction, measured at 20 ke V, of0.9 or greater, showed a decrease in the silicon fraction of signal with decreasing incident electron energy, down to values of between 0.6 and 0,8 at 5 keV: this decrease was a function of particle size and composition. Simple models for silicon fractiol) of signal vs incident electron voltage suggest this behavour is due to a heterogeneous particle structure in which an aluminosilicate coating occludes the surface of a silica particle core. The coating survives incubation in a major component of pulmonary surfactant.INTRODUCTIONMINING and some other dusty workplace atmospheres are monitored for respirable dust and quartz dust for purposes of occupational health protection, respirable quartz dust being a known cause of pulmonary disease. Respirable quartz exposure data are acquired also for epidemiological research on the correlation of pulmonary disease prevalence with respirable dust composition and concentration. For these purposes quartz content often is measured on collected dust samples by X-ray diffraction or in spectroscopy. Scanning electron microscopy-energy dispersive X-ray analysis spectrometry (SEM-EDX) is also used. The first two methods measure the bulk composition of a multi-particle dust sample; SEM-EDX measures the elemental composition of single ·particles. These methods as typically applied, including SEM-EDX with a 20-30 kilo-electron volt (keV) electron beam accelerating potential, do not distinguish homogeneous distribution of impurities in a particle from possible heterogeneous surface distribution. These measurements of quartz content are not always accurate predictors of the prevalence of dust-induced disease (ROBOCK and BAUER, 1990), which implies that the biologically available quartz surface may not be equivalent to conventionally measured quartz content of respirable dust in some exposure settings. Using a minor modification of conventional scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) protocols on samples of settled and airborne dust from a clay mine and mill we have detected heterogeneity with depth for aluminium impurity in high silica content particles, indicating that some of the quartz or 'free silica' respirable particles of the dust are aluminosilicate occluded. Coatings were not removed by incubation of the dust in a surrogate pulmonary hypophase surfactant fluid."

Jan 1, 1990

By Timothy J. Orr, Michael J. Beus, Frank T. Duda

The technology to enhance safety and control features for mine shaft hoists is being investigated by researchers at the U.S. Bureau of Mines (USBM). The objective of the research is to prevent injuries and fatalities related to hoist and elevator operations. Monitoring and controlling mine hoisting operations will allow hoist operators, inspectors, and maintenance personnel to increase their awareness of potentially dangerous situations and provide controls for safer operations. Process simulation and visualization software, real-time data sensing, and advanced programming techniques are being applied to this problem. Development of reliable and cost-effective sensors and data acquisition interfaces to monitor hoist loads and detect slack rope conditions is underway. Three-dimensional design software was used to visualize mine hoisting to enhance understanding of hoist operations. Quick Basic and Visual Basic (an object-oriented Windows interface) are being used for acquiring and processing hoisting data. Testing and evaluation of components are underway at USBM testing facilities. The resulting system will allow hoist personnel to assess critical operating parameters, such as hoist position, speed, acceleration, conveyance load, and rope tension.

By R. P. Beyer

As part of its thermodynamic investigations of mineral compounds, the Bureau of Mines has written an algorithm based on Newton's method for solving for the characteristic Debye temperature of a compound, from heat capacity and temperature data. A listing of a FORTRAN IV program based on this algorithm, for calculating Debye temperatures given heat capacities or for calculating heat capacities given Debye temperatures, is available from the author upon request.

Jan 1, 1981

By Bruce K. Cantrell, Stephen W. Stein, David Hassel, Harvey Patashnick

The Mine Safety and Health Administration. Department of Labor, requires coal mine operators to measure compliance with federal re¬spirable dust exposure standards periodically using approved gravi¬metric samplers. However, the gravimetric approach, with its inher¬ent delays, cannot provide dust concentration data quickly enough to allow on-site correction of inadequate dust control strategies or re¬moval of personnel from harmful environments. Furthermore, alleged tampering with dust samples collected to determine compliance with standards prompted the Secretary of Labor to appoint a special Respirable Dust Task Group to study options to improve monitoring and control of respirable coal mine dust. The Mine Safety and Health Administration's Task Group recommended that the U.S. Bureau of Mines develop a fixed-site monitor that would provide continuous information to the mine worker and mine operator regarding dust levels and the status of compliance with the applicable respirable dust standard. In response to the Mine Safety and Health Administration's request, the U.S. Bureau of Mines is investigating several sensor tech¬nologies for continuously monitoring respirable coal mine dust. One of these technologies is the Rupprecht and Patashnick Co. tapered element, oscillating microbalance. The bureau is in the process of investigating the suitability of using this sensor in the high humidity and vibration environment of underground coal mines. Laboratory tests have indicated that, with modification, the sensor can meet the humidity and vibration requirements for underground coal mine use. Currently, the bureau is developing

By H. G. Lucas

A feeder screw supplied at constant pressure by a hopper-orifice arrangement was developed for feeding solids in size ranges up to several hundred micrometers at constant flow rates. Performance of the feeder was evaluated by measuring the flow rates obtained with 3-to 7-micrometer coal ash, 70 percent through 200-mesh coal, and minus 325-plus 400-mesh coal ash. Constant feed rates within a few percent of set values were achieved for half-hour periods for the larger particles and for 5-minute periods for the finer particles. Suggestions are given for feedstock preparation and feeder operation for optimum performance.

Jan 1, 1974

By Jennifer A. Slatnick

The U.S. Bureau of Mines estimated the potential availability of titanium from 39 mines and deposits in 12 market economy countries. The evaluated properties account for 76 pet of the market economy country demonstrated resources, which total 603 Mt of contained titanium dioxide (Ti02) in the minerals rutile, ilmenite, leucoxene, and anatase, and represent 95 pct of current production. Approximately 250 Mt of contained Ti02 could be economically recovered from evaluated titanium operations at January 1992 market prices. In terms of mineral concentrates, this equals approximately 19 Mt of rutile concentrate, 110 Mt of ilmenite concentrate, 47 Mt of synthetic rutile concentrate (in addition to the ilmenite), and 160 Mt of titanium slag that could be recovered. Over the past decade, the titanium minerals industry has adapted to the changing market. In the 1980's, titanium producers expanded production because of the rising demand for titanium products. Today, the titanium industry is in a state of overcapacity, and byproduct revenues, such as that from zircon, have become essential in keeping operations profitable. The industry has also witnessed a greater dependence on upgraded ilmenite products, such as titanium slag and synthetic rutile, because of the expense of rutile and the lower wastes emitted from these upgraded products. As a result of this dependence on upgraded ilmenite products, South Africa has become a leading titanium producing country and has displaced Australian production.

Jan 1, 1994

Remotely monitor overburden response to longwall mining using time domain reflectometry (TDR) and a combination of hardware and software, as part of the U.S. Bureau of Mines (USBM) program to characterize subsidence. Background TDR was developed in the 1960's as a method to locate, discontinuities in coaxial transmission cables. In this method, voltage pulses sent along a cable are reflected by cable defects. The pulse reflections are used to determine the type and magnitude of the defects. The TDR concept was extended to material property measurement by embedding cables into particular materials and evaluating the cable's dielectric behavior as material properties were modified. This technique was adapted by the USBM in 1978 for use in monitoring rock movement during underground mining. The same concept is utilized today. A coaxial cable is grouted into a rock mass that is expected to deform. Progressive rock movement causes the cable to deform, as shown in figure 1, and changes to occur in the cable's electrical properties, which then produce changes in TDR reflection signatures. The technology has advanced to the point where it is now possible to distinguish shear deformation from tensile deformation and to quantify rock mass displacements by analyzing the TDR signatures.

Jan 1, 1995

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.

By C. L. Severy

On the Pacific coast during World War II, a tremendous ship-building industry was developed, Early in the war it became impossible to obtain in- got or steel scrap for ship ballast. Magnetite, an oxide of iron, was sub- stituted as it fulfilled the requirements of weight for available space in the ships. Consequently, a new use for the western magnetite was rapidly developed.

Jan 1, 1948

Design and test a high-production coal mining machine that generates less respirable dust. Background Current coal cutting systems generate excessive amounts of airborne respirable dust and fines during the mining process. Dust control technologies, including dust dilution by ventilation and suppression by water sprays, are not always able to reduce dust levels sufficiently. The U.S. Bureau of Mines (USBM) has designed a cutting system that reduces respirable dust generated by the cutting action of the drum. This cutting system, based on geometric principles developed in the 1500's, makes use of a constant depth, linear cut to remove coal at deeper cut depths and at lower rotary speeds than a conventional rotary drum. A comparison of the linear and rotary cut paths is shown in figure 1. Approach A full-scale prototype of the linear cutting concept was valuated under laboratory conditions to determine its performance relative to standard rotary drums. Results of these evaluations show production of fewer fines, or more uniform product size, a significant reduction in the amount of airborne dust, and reduced torque and power requirements (figure 2). On the basis of these results, a contract effort was undertaken by McCracken and Associates of Bristol, TN, to design a linear cutting head for underground testing.

Jan 1, 1995

By R. V. Ramani, V. T. Burgos, J. A. McClay

Summary Cost models have, long been confined to the accumulation and analysis of static-data.. While historical and time study data are valuable for control of existing operations, for new systems and equipment, and for projections, they need to be adjusted or modified. The availability of computer-oriented systems simulators provide yet another method for costing these systems and equipment. This investigation has introduced a concept whereby continuous, variable data can be assimilated and analyzed through the combination of an economic analysis model, which includes a direct costing capability, with a systems simulator. This tandem operation permits increased flexibility and greater atten¬tion to detail in the evaluation of mining systems. The direct costing process is carried throughout the majority of the model operations. Labor and capital costs may be computed directly, even in the absence of the systems simulator, while operating costs re¬quire input parameters, at present, from the subsystems of the Master Design Simulator. Since the costs computed are based on the perfor¬mance of each individual machine unit, the model may be used to evaluate equipment compatibility, system interaction at the mining face, and the effect of system elements on total mining costs. Additional applications of the cost model include the following: 1. Complete mining systems may be evaluated, over their economic life, to determine the feasibility of a profitable operation. 2. Costs associated with mining various segments of the coal deposit may be computed as a guide to planning the mine layout and scheduling the sequence of operations or acquisition of new

Jan 1, 1975

By A. W. Maynard

Simple chemical spot tests for the identification of major alloying elements in aluminum-base alloys are described. The tests are suitable for use by nontechnical personnel working outside a laboratory. Tests for zinc, copper, manganese, and magnesium employ electrographic sampling methods and sample papers. Use of electrographic sampling in a test for magnesium in aluminum is made possible by using glass fiber filter paper. Differentiations between magnesium and magnesium-silicon alloys of aluminum and between aluminum-base and magnesium-base alloys are made by direct chemical solution tests. Description of a device for obtaining reliable electrographic samples is included. A sequence of testing for identification by alloy groups is given.

Jan 1, 1971

Provide a low-maintenance, reliable means of generating bubbles and controlling bubble size for column flotation. Approach Commercial sparger systems used in flotation columns to process minerals provide only limited means of controlling the size of bubbles generated and the rate of air injection. Generally, these limitations are a detriment to flotation performance, particularly in recovering coarse or fine mineral particles. In addition, conventional bubble generation systems require frequent maintenance, often requiring shut-down of the column itself for repairs. To permit greater control of the bubble size generated in the flotation column and to eliminate the counter-productive problems associated with the operation of current air sparger systems, the Bureau of Mines investigated alternative methods for generating bubbles. Based on the investigation, an external bubble generation system was designed, developed, and laboratory and commercially tested.

Jan 1, 1987

Establish a procedure for reliably determining cation exchange parameters at an in situ mining site. The Problem Predicting the movement rates of pollutants from waste disposal sites requires reliable measurements of cation exchange parameters since cation exchange can retard pollutant movement. Reliable measurements of these parameters are also required for predicting the length of time needed to restore groundwater quality after in situ mining. Cation exchange is otten the controlling mechanism for the replacement of leach solution cations by the cations in the returning ground-water. Unfortunately, laboratory measurements using core samples are of minimal reliability. The uneven clay distribution at most sites produces a high variability in laboratory results. In addition the flow pattern in the laboratory tests is different from that in the field. Approach Bureau of Mines research has developed a field-test procedure that is quick and yields reliable and representative data. A corresponding data analysis procedure was also established in order to verify the' applicability of the computer simulation model of cation exchange used in the analysis, and of the general analysis procedure, with actual field data.

Jan 1, 1986

Locating subsurface conductive solutions is important for many applications, including in situ mining and environmental protection. Drilling boreholes for sampling is expensive and can increase contamination by mixing water from different aquifers. Various noninvasive geophysical methods are available, but previous comparisons were hampered by different methods being used at different sites or at different times. The U.S. Bureau of Mines (USBM) compared methods at one site using the same conductive solution to improve the reliability of the comparisons. Locating deep (> 100 m) solutions is most difficult, SO the USBM selected methods applicable for such depths. Objective Improve the ability to locate subsurface conductive solutions by evaluating and comparing applicable geophysical methods. Approach The experiment was performed cooperatively with other agencies to increase the number of methods studied. The USBM, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in detecting salt water brine of conductivity 3.6 S/m collecting at the water table, 157 m subsurface. The brine was injected through two boreholes. The test site was the University's San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetics (TEM); surface controlled-source audiofrequency magnetotellurics (CSAMT); surface magnetic field ellipticity, surface-borehole, frequency-domain electromagnetics (FEM); and crosshole FEM were conducted before and during brine injection. A total of 110,000 I. of brine was injected over one week, but the effective target volume of brine was much smaller because of mixing with ground water and dispersion.

Jan 1, 1994

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

By A. D. Mah

Thermodynamic data on compounds of arsenic and sulfur were critically evaluated by the Bureau of Mines. Changes of standard enthalpy and Gibbs energy, and logarithms of the equilibrium constants were tabulated as a function of temperature for reactions involving these compounds.

Jan 1, 1982

By R. Karl Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model, and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed that allows the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

Jan 5, 2007

By Sarkis G. Ampian

The Bureau of Mines has developed a method for identifying fine particles of beryl in mineral samples by preferentially staining the beryl grains. The sample is first subjected to a heated sodium hydroxide solution to etch the beryl particles, which are subsequently stained an intense blue color in a boiling alkaline solution of quinalizarin. Positive identification of beryl grains permits quantitative analyses by microscopic techniques. INTRODUCTION Beryl, a beryllium aluminum Silicate, is the principal ore mineral of beryllium. The only known commercial concentrations of this mineral are found in pegmatite dikes of granitic composition. Normally beryl is associated with muscovite mica, quartz, and the sodium-and potassium-bearing feldspars (orthoclase, microcline, and albite). Other beryllium-bearing minerals which are found occasionally in minor amounts with beryl are phenacite, a beryllium silicate, and chrysoberyl, a beryllium aluminate.

Jan 1, 1962

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990