Search Documents

By Julian Vigil

Mountain bumps have been a problem in the coal-mining industry since the 1920's. The problem became severe in the late 40's and early 50's with the introduction of mechanized mining. Fatalities and serious injuries resulted from mountain bumps during this period. Mountain bumps again caused fatalities in the 80 's. Interviews were conducted mostly with retired coal miners having experience in bump conditions with five different coal companies. These men held positions as president, general manager, roof-control specialist, mining engineer, inspector, superintendent, mine foreman, shift foreman, section foreman, miner operator, electrician, and general laborer. Together, their comments give a good idea of the things tried to mitigate mountain bumps in the Appalachian Coal Fields.

Jan 1, 1991

By John S. Berber

Bureau of Mines research on the production of phthalic anhydride by vapor phase oxidation of hydrocarbons began at Morgantown, W. Va., in October 1960. For these preliminary studies, a known solution containing naphthalene and 1-methylnaphthalene was used. In another series of tests, pure naphthalene was dissolved in different solvents. A series of investigations was conducted with the neutral oil fraction (210° to 270° C) of a low-temperature tar obtained from the Texas Power and Light Company's low-temperature carbonization unit. The neutral oil fraction was first dealkylated, and then the product was distilled into 210° to 250° C and 250° to 270° C fractions. These two fractions were then subjected to catalytic vapor phase oxidation. Although a number of catalysts was tested, most of the experiments were made using 9 percent vanadium pentoxide on inert alumina. The activity of this catalyst did not decrease after 162 hours at 1,030° F. Studies were conducted over a temperature range from 610° to 1,180° F. An operating temperature of 1,030° F yielded 47.50 percent of phthalic anhydride from a synthetic mixture of naphthalene and 1-methylnaphthalene. The highest yield (84.40 percent phthalic anhydride) was obtained with naphthalene dissolved in toluene and also with naphthalene dissolved in methyl ethyl ketone. With a 210° to 250° C fraction the highest yield of phthalic anhydride obtained was 12.32 percent at a temperature of 900° F, and, with a 250° to 270° C fraction, it was 15.80 percent at a temperature of 875° F.

Jan 1, 1963

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

During the 1990s, the former U.S. Bureau of Mines conducted a number of field studies in which the performance of different types of roof bolts were evaluated in different geologic environments. The studies used a standard suite of measurements, including multipoint extensometers, strain-gauged roof bolts, and roof bolt load cells. The sites were chosen to investigate the effect of a variety of parameters, including installed tension, bolt capacity, grout annulus, and horizontal stress orientation. Although not fully successful, the measurements provided valuable insights into each of these issues. They also showed that instrumentation and monitoring have important advantages over observational methods for comparing the performance of different roof bolting systems.

Jan 10, 2000

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

By RUDULF KUDLICH

Pennsylvania anthracite coal is almost universally recognized to be the solid fuel best suited for domestic use when cleanliness , convenience and cost are considered . At various times and in various localities , however, conditions so affect the supply that it becomes insufficient or is too high in price and recourse must be had to other fuels as substitutes . In practically every district in the United States where anthracite has been the common domestic fuel , some other fuel is available as a substitute . In even the most severe climates such fuels are used either as emergency substitutes for anthracite , or as the ordinary domestic fuel . There may be some drawback to the use of such fuel , such as the need of more frequent attention to the furnace , smoke , soot and dust , in the case of solid fuels lower in price than anthracite , but these inconveniences must be accepted as necessary accompaniments to a decreased fuel bill . The cleanliness and ease of handling anthracite in the house must be considered in the light of a luxury and a higher cost of heating with this fuel must be expected . That a growing number of people are willing to pay for such added convenience is evident from the increasing mumber of heating installations using oil , gas and electricity , all of which are more convenient and usually more expensive even than anthracite .

Aug 1, 1923

By Samuel W. McNary

In August 1984 the U.S. Bureau of Mines conducted a study of the mineral resource development potential of the Badger Canyon-Antelope Creek area, within the Boulder-Pioneer wilderness study area, about 5 miles northeast of Ketchum, 10. The purpose of this study was to investigate in greater detail an area which was designated by the U.S. Geological Survey (USGS) and the Bureau as having a moderate mineral resource potential for zinc, molybdenum, lead, and silver, and a low potential for copper. One hundred twenty-eight soil samples were taken along a 6,2S0-ft traverse on the ridge separating Badger Canyon and Antelope Creek. 5 Five rock samples were collected from old prospect pits and mineralized outcrops. All samples were analyzed for gold. Silver, copper, lead, zinc, molybdenum, arsenic, antimony, vanadium, and mercury. The metal concentrations in the soil samples along the traverse are irregularly distributed. Samples collected near old prospect pits tend to be high in lead and zinc, undoubtedly a reflection of underlying galena-and sphalerite-bearing quartz veins. All of the copper and mercury values in the soils are less than the detection limit, as are most of the lead, molybdenum, and antimony values. Except for lead and zinc values, the metal concentrations in the rock samples are low. Galena and sphalerite were observed in quartz vein samples collected at the old prospects. The results of the study indicate that the galena-sphalerite-bearing quartz veins and veinlets are too narrow, widely-spaced, and low in metal values to be economic. Low concentrations of metals in the soil and rock samples, combined with the lack of major mining activity in the past, indicate that the area has a low likelihood for economic development.

Jan 1, 1986

By T. J. Ballard, Austin B. Clayton

"INTRODUCTION The Conrad Hill mine was first opened as a gold mine about 1832 and has been operated at various times since then.The Bureau of Mines, as part of the strategic minerals program, mapped and sampled the accessible mine workings.The: work failed to reveal appreciable copper values or evidence of additional ore deposits.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the and that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The field work embodied in this report was under the direction of Austin B. Clayton. The final report was prepared by T. J. Ballard uncle,- the general supervision of Mitchell H. Kline, chief, Raleigh, N. C., Branch, Mining Division. Analyses of samples and beneficiation tests were made by the Metallurgical Division. ACCESS AND OWNERSHIPThe property is 6 miles southeast of Lexington, N. C., and can be reached by U. S. Highway 64, turning off at Hedrick Grove Church, and is 1 mile north from the highway on the county road. The mine is in Davidson County at approximately 35° 47' latitude and 80° 10' longitude (fig. 1).The property comprises 471 acres and is owned (1943) by the McKeeMining Co., 512 Fifth Avenue, New York City. The property was optioned to Woodrow McKay of Lexington, N. C., in 1943, who in turn subleased the property to the Robert G. Lassiter interests of Raleigh, N. C."

May 1, 1948

By Michael D. Fenton

The modest mineral industry of Afghanistan continued to suffer adversely from internal disorders that were essentially the result of the continued presence of elements of the armed forces of the U.S.S.R. Despite press reports near yearend intimating that the Soviets might reduce troop strength in Afghanistan, there were no indications of any significant numeric reductions. Indeed, there were clear demonstrations of heightened military actions along the Afghani-Pakistani border, including bombing raids on settlement sites for Afghanis within the territorial limits of Pakistan, actions hardly demonstrative of conditions indicative of Soviet withdrawal.

Jan 1, 1988

By Harry G. Dosh

Sillimanite, kyanite, and andalusite are aluminum silicates having the same chemical composition (Al2SiO5) and are used in the ceramics industry for the manufacture of high-grade refractories. Natural sillimanite with added corundum or other alumina to just short of mullite (3Al2O3 -2SiO2) proportions is unequalled for jobs wherein strength at high temperatures, resistance to spalling, and resistance to slagging by acid slags are desired. High-grade porcelain ware also requires these minerals. At the same cost, sillimanite would be preferred for most uses, but the lack of any large source of sillimanite bas given economic preference to kyanite or andalusite for special refractories and high-grade porcelain wares. Sillimanite-bearing schists were observed in Spartanburg County, S. C.; as early as 1937 by D. Hoye Eargle, geologist with the U. S. Soil Conservation Service. The mineral was not identified until 1942, when Miss Jewell Glass, of the U. S. Geological Survey, examined several of the deposits. This identification was confirmed in 1943 by Dr. Laurence L. Smith, of the University of South Carolina, when he examined the Spartanburg County deposits and found numerous additional occurrences of sillimanite schist in Greenville County. Subsequent work by the Bureau of Mines and the South Carolina Geological Survey has been responsible for the location of additional sillimanite-rich schist deposits in Spartanburg County. Between October 1, 1948, and November 21, 1948, the Bureau of Mines conducted an exploratory diamond-drilling project on the John Gideon property in the southeastern section of Spartanburg County (fig. 1) and drilled a total of 681.7 feet in six holes. Drilling indicated that the deposit is relatively shallow, as no ore was cut below the zone of weathering.

Jan 1, 1950

Only limited work has been reported in the literature about the use of latex in soil. Unisol 91 2,3 (a 9:l oil-latex emulsion made b International Synthetic Rubber Company) and Phil1ips Petroset4 geotechnic emulsions are surface soil stabilizers which penetrate a maximum of two inches, but do not reduce permeability. Diamond Alkali 5 found that styrene-butadiene rubber latex as a one percent latex-soil mixture reduced permeability to 0.7 from 21 feet per year under a head of twenty feet of brine. We have found no literature reference for use of latex as sealant at depth in the soil, although asphalt has been applied at depth using civil engineering methods6,7. Most of the materials investigated as soil sealants in the present work were latexes, although some studies were also conducted with a variety of inorganic and organic chemicals. Of the latexes tested, most were rubber but a few were plastic, e.g. polyvinyl chloride. Sealants examined in this investigation are listed individually in Table I with supplier, code number, and other pertinent information. The materials consisted of the following general classes with additional details as indicated: 1.Anionic latexes: a. styrene-butadiene copolymers and terpolymers (SBR) b. butadiene-acrylonitrile copolymer (Paracrils®) c. polyvinyl chloride homopolymers and copolymers (WC) d. ethylene-propylene terpolymer e. vinyl acetate homopolymers and copolymers (VA) f. acrylics (acrylate copolymers) g. 2-chlorobutadiene homopolymer (chloroprene) (prepared specially as cationic material coagulated by soil). 2. Water Soluble polymers: a. polyvinyl ether b. methylcellulose c. polyethyleneimines d. polyacrylic acid homopolymer e. copolymers and terpolymers with acrylic acid types (water soluble as sodium or ammonium salts) f. alginates g. monomers (for polymerization in soil, e.g. acrylamide)

Jan 1, 1972

By Jr. Schnakenberg

The National Institute for Occupational Safety and Health (NIOSH) has been working with diesel emissions control technology and the underground mining industry for a number of years. Underground isolated zone studies provided the emissions reduction performance of all of the alternative technologies currently available. A NIOSH/MSHA guide is available which provides mines with information and a process for selecting diesel particulate filters (DPF). Recent NIOSH experience suggests that more attention may be needed in managing the issues associated with diesel emissions and their control. The author argues that a holistic approach is needed which involves several key mine operations departments or disciplines by positing that workplace air can be considered as the product of a complex manufacturing process and examining how that process could be managed.

By A. T. Coumbe

The Bureau of Mines has compiled pipeline mileage every 5 years since 1926, with the exception of the war period 1941 to 1949. The present survey has been made to reflect the progress under mobilization of the petroleum pipeline industry where efforts have been made by the government to stimulate construction of those facilities that would best equip the nation for a possible major emergency. This report summarizes the total mileage change 1n petroleum pipelines for 1950 through 1952. In order to increase the value of the information gathered the reporting companies were requested for the first time to report not only the net change in mileage as formerly, but also all new and used pipe laid and the total taken up. This new information permits effective appraisal of the construction effort of the industry and relates it to steel requirements.

Jan 1, 1953

By Maria I. De Rosa

Table 28 and figure 10 show the number of fires and fire injuries for coal preparation plants by state during 1990-1999. Table 28 also shows the risk rates, employees' working hours, and lost workdays by state. For coal preparation plants, 91 fires occurred in 1 1 states during 1990- 1999. Twenty-three of those fires caused 25 injuries (the yearly average was 9.1 fires and 2.5 injuries). Ten fires and eight injuries involved contractors. The Ewhr value was 24 1 x 10' hr (Irr = 0.02 l), and the LWD value was 198. Pennsylvania had the most fires (24 fires and 4 injuries), whereas West Virginia (22 fires and 7 injuries) and Kentucky (22 fires and 7 injuries) had the most fire injuries. Among these states, Kentucky had the highest injury risk rate value (Irr = 0.025). Table 29, partly illustrated in figure 11, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires decreased during most of the periods (an increase is seen only during the last period). The number of fire injuries show a decrease followed by an increase during the periods, accompanied by a decline in employees' working hours throughout the periods. The Irr values follow patterns similar to those shown by the injury values (see table 29 and figure 11). Tables 30-35 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 12 shows the major variables during 1990-1999. Table 36 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Harold L. Gibbs

The purpose of this paper is to encourage petrographers to prepare thin sections, as the demand for microscopic examination of rocks, ores, and metallurgical products is becoming more general in .the mining metallurgical-fields. This paper has been written with the knowledge that the successful thin-section methods and the several new techniques herein described will be helpful to all engaged in this field of work. Detailed instructions for making thin sections by methods developed at the Salt Lake-City laboratory of the Bureau of' Mines are given in this paper. Several new techniques are described for making thin sections of loose grains and fine sands and for making good thin sections of highly altered and friable rocks. The methods described insure superior bonding of the rock to the glass slide, thus virtually eliminating any failures due to parting of the section from the glass slide, and permit fast mounting, grinding, and finishing, thereby materially lessening the time required to prepare thin sections.

Jan 1, 1950

By Leonard Obert

[Tng occasional. rock noises in a nice caured by brc,*ing and ripping of the back, settling, and other cailscr, are well-known tc~ a11 mining en- gineers. These noises oftcn prececte certnin tpes of rock failure as such are used to e certain event a; w:,rnlngs. Senides t5ese audible rock noisee t'nere are, l?o\;evpr, even Iprger nw.iber of' s;Lba.J^;li5le rock mis~s, which must; be piclcell UT with sole type of vi-urr,tion rnicroyhoce and qli- fied in order tnnt :hey n;ny e heard. It v:zs s~v;,yestec" Ir, an evlier ? ,I a.ldible noises Ifureau of I.lines s~zb:ic;et.iod that n stud:r of t!ler;c! *- t mig!!t be useful ir. de temining roc^ movemrnt 3 preceding failure.]

Jan 1, 1941

By J. W. Thompson

ORE CONCENTRATION PROCESS-PATENT OIL FLOTATION PROCESS. The invention of the patent issued to Sullman, Picard & Ballot November 6, 1906 (United States Letters Patent No. 835120), is based upon the discovery of an wholly unexplained phenomenon arising from the agitation of ore pulp containing oil and air in certain proportions. This was a discovery in an art in which it was well known that the elements of oil, air, and agitation possessed certain characteristics and produced certain results. As early as 1860 a British patent first suggested the use of oil in water concentration of ores by pointing out the affinity which oils have for metallic sub- stances in preference to gangue. Subsequently many patentees employed the known affinity of oil for metal in ore concentration proc- esses by using oil in proportions varying from 2 per cent to 300 per cent of the ore and recovering the oil-coated metal particles by causing them to rise to the top or sink to the bottom of the pulp. In these processes the agitation was either gentle or thorough but never great, and though always employed to produce thorough oiling of the metal it was used in different degrees for the sole pur- pose of causing the metal particles to rise or sink. In the prior art the oil was used for its known selective affinity for metal, agitation was em- ployed to mix the oil with the metal, and air was introduced to supple- ment the buoyancy of oil in raising oil-coated metal particles to the surface. To this extent had the art of oil flotation advanced when the patentee entered it, having reached the commercial stage in only two processes, representing respectively metal-flotation and metal-sinking processes, and having reached the stage of success in none. In the line of experiments by the patentee when the proportion of oil to ore was reduced to 1.5 per cent a "float" appeared; at 1.04 per cent still more "float" appeared; at 0.32 per cent the "float" again vastly in- creased; at 0.1 per cent the "float" again vastly increased. It thus developed that in using oil at 0.1 per cent or even at 0.05 per cent of the ore and after violently agitating the pulp from 24 to 10 minutes, there arose to the surface when the pulp was brought to rest, a thick froth or foam of oil-coated air bubbles carrying oil-coated metal particles to the extent of about 90 per cent of the metal con- tent, the foam being sufficiently stable to permit removal and metal recoveries. This was a new result based upon phenomenon then unknown and still unexplained and constituted discovery and promised a change in the art of oil flotation from laboratory experi- ments and mill failures to commercial success. The patent referred to covering the points mentioned has been sustained by the District and the Circuit Courts of Appeals and by the Supreme Court. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, pp. 754-757. ORE CONCENTRATION PROCESS-OIL FLOTATION-INFRINGEMENT. The Miami Copper Co. in its process of concentrating ores by the oil flotation process used three distinct processes that were either the processes included and covered by the Sullman, Picard & Ballot patent or their fair equivalent and which were clearly an infringe- ment of the patent, and the company can not escape liability for such infringement by taking an additional step, although such additional step if taken alone would not constitute an infringement of the Sullman, Picard & Ballot patent. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, p. 768. ORE CONCENTRATION PROCESS-VALIDITY OF GREENWAY PATENT. The patent issued to H. Greenway, June 9, 1914 (Letters Patent No. 1999699), is valid. The process disclosed in this patent was a substantial departure from processes of the prior art. The heating of water is a matter of large moment and the use of acids is a matter of constant and considerable expense. By wholly dispensing with both by the use of a minute quantity of hydroxy compounds, the patentee has disclosed an original and novel plan which has broad- ened and made more simple the agitation process of air flotation. The novelty and inventive character of Greenway's discovery is patentable.

Jan 1, 1918

By Thomas J. Fisher, John J. Sammarco

This report (System Safety 2.1) is the second in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 [IEC 1998a,b,c,d,e,f,g] and other recognized standards. The scope is “surface and underground safety mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system.

Jan 4, 2001

By Ronald S. Conti

This paper describes technology and training that has been identified for underground emergency responders. Historically, underground mine rescue teams have only received training in the course of actual emergencies, or in simulated mine environments, usually on the surface, with placards to identify objects and hazards. Also, while U.S. Federal Regulations require all underground miners to walk escapeways and conduct fie drills every 90 days in a smoke-free environment, this does not fully prepare them for the conditions that will be encountered in real escape situations. Therefore, it is extremely important that miners are provided with adequate technology and that training simulations are conducted in a realistic manner. A series of mine rescue training and mine emergency response development (MERD) exercises, and in-mine smoke training was developed, conducted, and evaluated by state and company teams, and by National Institute For Occupational Safety and Health (NIOSH) personnel. The training exercises were held at NIOSH's Lake Lynn Laboratory (LLL) and operating mines during the past several years. This training resulted in improved technology and training for mine rescue teams, fire brigades, first responders, and miners in general. For example, existing technologies were identified to help responders during exploration and recovery operations. These included various chemical light shapes, strobe lights, light vests, and laser pointers to identify team members. Most of these devices may be used to mark underground areas and certain mine materials. Strobe lights were used for mapping out escapeways and lasers were used to negotiate travel through smoke. Thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, and allows the user to easily locate missing or trapped personnel and heated areas. A hands-free communication system showed potential for enhanced communications between team members, the fresh air base, and command center. A new team lighted-lifeline allows for flexibility in movements of team members during routine tasks and allows them to easily find their fixed position on the lifeline. Of all the technology evaluated by underground personnel, laser lights and lifelines were most beneficial in leading personnel to safety and out of the mine in smoke-filled passageways. A positive-pressure inflatable escape device (IED)/airlock, was used to isolate the "hazardous" environment from fresh air and allow rescue team members to traverse through. An inflatable feed- tube partition that can rapidly block large openings such as underground passageways or tunnels and simultaneously provide a feed-tube for high-expansion foam generators was also deployed during the simulations. These technological advancements have improved the state of readiness for rescue personnel and have increased the chances of survival for all personnel escaping from underground emergencies.

By Maria I. De Rosa

During 1990-2001, a total of 518 fires occurred in all metal/ nonmetal mining categories; 296 of those fires caused 308 injuries and 4 fatalities. Surface operations had the most fires and the highest injury risk rate values. Forty-five fires destroyed or heavily damaged facilities and equipment (including 19 pieces of mobile equipment) because of failure of firefighting methods, late fire detection, undetected fires, or fire size. In the future, many of these fires and injuries might be prevented or detected and extinguished at their earliest stage by improving current fire safety procedures, adopting existing/ improved fire detection and suppression technologies, and/or developing new technologies. Several strategies for reducing and/or preventing the number of fires and fire injuries follow. I. Increase vigilance, improve safety procedures, and develop new technologies in order to prevent fires and injuries caused by fame cutting and welding operations. 2. Improve equipment hydraulic/fuel/electrical systems inspection programs; adopt fire-resistant hydraulic fluids and electrically powered motors for use in underground mines; develop new technologies (equipment/cab rapid fire detection/ prevention/suppression systems, emergency line drainage systems, and fire barriers); adopt an optimal ground level location for the activation of emergency systems; improve operator's fire preparedness training programs; and develop effective and rapid local firefighting response capabilities. 3. Adopt existing/improved systems for continuous and early detection of combustion gases and smoke along beltlines. 4. Adopt existing/improved technologies for monitoring equipment (beltlines) operational functions. 5. Increase vigilance and adopt improved safety procedures for handling f amenable liquids and refueling fuel in the vicinity of heat sources.

Jan 1, 2004

By Mark S. Sanders

The purpose of this work was to develop and field test improved knee protection for underground coal miners working in low seam mines. In a previous phase of this contract (Sanders, 1982), experimental knee pads were developed and field tested. The field test revealed several design deficiencies with the knee pads, and suggestions for improving the design were made. The work summarized in this report, therefore, consists of modifying the design and method of fabrication of the knee pads originally describes by Sanders (1982), and of field testing the improved design. The new prototype was shorter and wider than the original design, and used a neoprene pass-through strap design rather than a cloth strap molded into the pad itself. The new prototype was constructed by slush molding a hollow bladder that was then filled with foam. Initial reactions to the pads in the field test were very positive. However, after two months, the opinions about the new prototype became less positive. They were judged, generally, to be no better or worse than the pads usually worn by the field-test participants. Problems were encountered in the field with respect to durability. Water seeped into the inner cavity of many of the pads and caused the foam to deteriorate. It was concluded that it would not be cost-effective or feasible to significantly improve upon current commercially available knee pad designs.

Jan 1, 1986