Search Documents

By C. M. Flynn

The Bureau of Mines prepared and investigated xanthated sawdust adsorbents to determine their effectiveness in removing heavy metal ions from dilute aqueous solutions, mine-drainage waters, and brines. Stripping of the metal values from the metal-laden adsorbent was also investigated. The treated sawdusts had an adsorption capacity of 0.3 to 0.4 meg/g dry adsorbent for Mn, Co, Ni, Cu, Ag, Zn, Cd, Hg, or Pb from feed solutions with pH 5 to 6. The feed solutions tested included mine-drainage waters and geothermal brine. Effluent metal concentrations as low as 0.05 to 0.1 mg/l were obtained at effluent pH values of 6 to 9. The order of affinity of metals for the sawdust adsorbent is Na«Ca~Mg~Mn<Zn<Ni<Cd<Pb~Cu. The presence of Ca, Mg, or Na in concentrations as high as 2 g/l does not seriously impair the heavy-metal adsorption. Metals were desorbed from the metal-laden adsorbent by elution with dilute mineral acids, sodium cyanide, or salts of ethylenediaminetetra-acetic acid.

Jan 1, 1979

By S. J. Schatzel

In an effort to increase productivity, many longwall mining operations in the U.S. have continually increased face lengths. Unfortunately, the mining of larger panels may increase methane emissions. The National Institute for Occupational Safety and Health (NIOSH) conducted a mine safety research study to characterize and quantify the methane emissions resulting from increasing face lengths in the Pittsburgh Coal-bed. The goal of this research effort was to provide the mine operator with a method to predict the increase in methane emissions from the longer faces for incorporation of additional methane control capacity into the mine planning process, if necessary. Based on measured methane emission rates of 0.066 m3/s (140 cfm) for a 315 m (1032 ft) face, projected longwall face methane emission rates were 0.090 m3/s (191 cfm) for a 366 m (1200 ft) face, 0.106 m3/s (225 cfm) for a 426 m (1400 ft) face, and 0.124 m3/s (263 cfm) 488 m (1600 ft) face.

Jan 1, 2006

By J. M. Stuve

A novel calorimetric solution technique, recently developed at the Bureau of Mines, was tested using synthetic samples of chalcocite (CU2S) and covellite (CuS). The solution of these refractory sulfides was accomplished by oxidation with bromine in a moderately acidic, aqueous solution. The resulting values for the standard enthalpies of formation (?Hf°, 298.15) for CU2S(c) and CuS(c) were -18.1 ±1.1 kcal/mol and -13.3 ±1.1 kcal/mol, respectively. These values are in good agreement with published formation values derived from other methods of physicochemical measurement.

Jan 1, 1982

By Thomas O. Llewellyn

Laboratory semicontinuous and continuous heavy liquid cyclone separation pilot plant tests were made to determine the feasibility of producing a high-grade kyanite concentrate from a kyanite-quartz rock sample from Graves Mountain, Ga. Use of a three-stage heavy liquid cyclone circuit demonstrated that a 96.4-to 99.0-percent kyanite concentrate could be obtained with recoveries of 95.5 to 96.7 percent. The test work showed that by steam stripping with 6.9 tons of steam per ton of ore and two stages of detergent scrubbing the residual TBE content of kyanite cyclone products was 0.22 pound per ton of ore.

Jan 1, 1971

By D. E. Ingersoll

This report describes the preparation characteristics of anthracite from the Mammoth and Holmes veins in Schuylkill County, Pa., as determined by the Federal Bureau of Mines laboratory separations at specific gravities of 1.50 to 1.90. The Holmes vein anthracite contains approximately 13 percent ash, and the Mammoth vein contains about 9 percent as fed to the breaker. Crushing Broken, Egg, and Stove sizes from each vein produces Pea-size anthracite of lower ash content than that contained in Buckwheat No.1 size and smaller. The Buck-wheat No.5 size has the highest ash content of all the sizes examined. Potential recovery from a mixture of the two veins as received at the breaker, separated at 1.90 specific gravity, is approximately 64 percent of the feed at 11.0 percent ash. The same materials separated at 1.80 specific gravity yield about 61 percent with an ash content of 10.1 percent. All rejects are from the Holmes vein, because the entire Mammoth material is less than 10.0 percent ash.

Jan 1, 1960

Enhance hydraulic fragmentation technology by developing alternative grout sealing methods. Traditional grout scaling methods rely on chemical adhesion and require large contact areas to restrict high-pressure fluids. Fluid injection into rock requires economical and effective seals. With economical and effective seals, rock is easily fractured in tension by high-pressure fluid injection (fig. 1). Approach An innovative grouting technique was developed and tested by the Bureau. Slowly hydrating expanding chemicals are placed within a borehole and around a section of high-pressure tubing. Testing was conducted using 9/16-inch-OD smooth-walled injection tubes in 1.5-inch-ID holes. Seal lengths weir less than 10 inches and curing times were less than 24 hours.

Jan 1, 1989

By Mary H. Brown

The heats of formation of oxalic acid and sodium, potassium oxalates, and lithium oxalates were related by solution calorimetry to the heat of formation of (COOH)2.2H20, a value believed to be reliable as reported in the literature. The following heats of formation were determined: (COOH)2(a), -198.1±0.1; (COOH)2(ß), -197.8±0.1; UAW,, -328.7±0.4; Na2C204 -316.2±0.1; K2C204, -321.9±0.2; and K2C204-H20, -393.5±0.2 kcal/mole. The heat of the crystalline transformation (COOH)2(a) ? (COOH)2(ß) was determined to be 0.30±0.02 kcal/mole at 298.15° K.

Jan 1, 1970

By H. C. Ko

As part of the Federal Bureau of Mines effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation, the standard enthalpies of formation of a-magnesium sulfate, a-magnesium sulfate, and magnesium sulfate monohydrate were determined by hydrochloric acid solution calorimetry. The values of the standard enthalpies of formation in kcal per mole at 298.15 K are -307.95 ± 0.13 for a-MgS04, -307.03 ± 0.13 for ß-MgS04, and -384.72 ± 0.13 for MgS04 .H2O.

Jan 1, 1979

By Michael J. Brnich

Since 1991, Pittsburgh Research Center (PRC- formerly part of the Bureau of Mines) researchers have recorded extensive interviews with 30 individuals who are experts in the area of mine emergency response. These individuals, who have an average of 35 years of mining experience and 29 years of mine emergency response experience, related stories and observations from events that they experienced during their combined 850 plus years in mine emergency response. The purpose of this effort was to gather information that could be passed onto both today?s and tomorrow?s mine emergency responders to train and guide them in handling future events.

Jan 1, 1997

By D. S. Kingery

The control of coal dust on coal tipples and cleaning plants has not been given the consideration that is afforded underground dust hazards. This apparent oversight is undoubtedly due to the general opinion that coal-dust accumulation in tipples or cleaning plants does not present the same type of hazard that it does underground. That this opinion is at least in part a fallacy has been proved many times, and the Bureau of Mines has on record many examples of explosions in tipples and cleaning plants.3/ In addition to this explosion hazard, coal dust is considered by sonic authorities to be injurious to the health of individuals exposed to it.4/ Obviously, it reduces visibility and contributes materially to accident hazards and the discomfort of the employees. Several companies have recognized this dust hazard and the advantages derived from controlling it; consequently, they have installed equipment to allay and control the dust on, their cleaning plants and tipples. The object of this paper is to. Summarize briefly some of the methods new in effect.

Jan 1, 1943

By Webster S. Anderson

Two series of tests were run with planer model &apos;BB": one at the Arickaree mine of the San Francisco Chemical Co., Rich County, Utah, and one at the Roslyn No. 9 mine of the Northern Pacific Railway Co., Roslyn, Wash. The tests at the Arickaree mine were started on June 25, 1958, and continued until September 30, 1958. Prior to these tests, an electrically activated remote-control system was installed, and other modifications were made on the planer. The tests showed that the planer in general and the remote-control system worked very well; however, the various cutting tools used would not consistently penetrate and cut the phosphate rock. This indicated that the cutterhead design had to be changed before the planer would operate efficiently in phosphate beds similar to the "A" bed in the Arickaree mine.

Jan 1, 1962

By R. H. Fernald

In investigating general problems that relate to the fuel resources of this country, and in testing fuels belonging to or for the use of the Government, the Bureau of Mines has given considerable attention to the efficiency and economic value of producer-gas power plants. Government inquiries during the past eight years not only have shown a very low fuel consumption per horsepower-hour for these plants but have demonstrated conclusively the possibility of utilizing commer- cially low grades of bituminous coal, lignite, and peat in plants prop- erly designed for the use of these fuels. The anthracite plant has been recognized as a commercial possibility for several years, although the cost of the fuel used has in general restricted these plants to com- paratively small units. The commercial development of the producer-gas power plant in the United States has been largely within the past six or eight years. In 1909 the United States Geological Survey published in a bulletin entitled "Recent Development of the Producer-Gas Power Plant in the United States" a list of producer-gas power-plant installations. The data presented in that bulletin showed a strong development in this field and led to much conjecture as to the future of this type of power. Owing to the extensive introduction of the steam turbine, however, many persons predicted the almost immediate doom of the producer-gas plant. In addition to the inroads made by this formida- ble rival, the interest of the gas-engine enthusiasts became centered to such an extent in the oil engine that the gas producer was relegated to second place by many and absolutely abandoned by some. During the past three years the belief of many who were formerly firm be- lievers in the gas producer has been that this type of power has reached its height of development in this country and that from a commercial standpoint it can no longer be regarded as a complete success. This feeling of commercial decadence has become so general

Jan 1, 1913

By D. R. Tesarik, R. W. McKibbin

Material properties affecting slope stability were measured in a large 50-year-old, partially consolidated rockdump located in an active open-pit mine. Field tests included single-ring infiltration and density. In addition, a nuclear depth-moisture gauge was used to measure water content in six stainless-steel-cased drill holes on the crest and an upper bench of the rock dump. Precipitation, evaporation, wind speed and direction, and temperature data were collected at a weather station installed on the dump’s crest. Laboratory tests included particle-size distribution, specific gravity, Atterberg limits, and water content. By measuring material properties of a rock dump presumed to be stable, the safety of miners working on or at the toe of old rock dumps constructed of similar material and located in a similar climate can be assessed.

Jan 1, 1999

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface coal mining categories by state and2-year time periods during 1990–1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from Mine Safety and Health Administration (MSHA) mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and will form a basis for future fire research programs.

Jan 9, 2004

By Charles Sabine

The 27,960-acre Newberry Mountains Wilderness Study Area (WSA) is located in the Mojave Desert, 17 miles east-southeast of Barstow. In 1983, the U.S. Bureau of Mines, in conjunction with the U.S. Geological Survey, investigated mineral resources of the area as part of the wilderness review process. The Newberry Mountains are underlain by Paleozoic metamorphic rocks, Mesozoic plutonic rocks, and Tertiary volcanic rocks. Eleven mines and prospects were examined. Of the seven sites within the WSA, only the Northrup Prospect is mineralized. Only a few tons of manganese-bearing rock, containing 49% manganese oxide (MnO), are exposed, but exploration may disclose larger deposits. The Azucar Mine, a past producer of gold, is the only site examined outside the area that appears mineralized. Sample data from quartz veins exposed at the surface do not indicate that resources are present; however, the occurrence could not be fully evaluated because underground workings were not accessible. Sand, gravel, and stone are plentiful in the WSA, but alternate sources outside the WSA are available.

Jan 1, 1985

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface coal mining categories by state and 2-year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from Mine Safety and Health Administration (MSHA) mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and will form a basis for future fire research programs.

Jan 1, 2004

By R. V. Ramani

"In a 1985 seminar, we were told that over-optimism abounds in Artificial Intelligence (AI), that AI is neither a science nor a technology yet, and that we will be both exhilarated and disappointed with AI. In fact, even today, there is no single accepted definition of AI; however, certain features have been identified by AI researchers as essential to consider an entity (e.g. machine or program) to be intelligent. According .to Shank (1987), these features include communication (to be able to communicate with), internal knowledge (knowledge about itself), world knowledge (awareness and knowledge about the world outside), intentionality (knowing what one wants and a plan to seek it, ie. goal seeking behavior), and creativity (being adaptable to changing conditions). None of these figures would individually define intelligence; however, each would be a part of intelligence in its own way.The prospects for the development of entities with AI have never been as good as they are now. The combination of advancements in computer hardware and .software along with new insights into the ways in· which we store knowledge and use it for problem solving has enhanced the potential for the creation ~f intelligent entities. After some unbounded optimism of a major breakthrough in the fifties and frustrating disappointments in the two following decades, it appears now that AI has emerged from research labs to industrial practice. This is confirmed by the growing number of repeat applications of AI in business and industry to the extent that AI can now be considered a technology.AI applications are categorized into several distinct areas such as Natural Language Processing, Speech Recognition and Synthesis, Expert Systems, Robotics, Machine Vision, etc. Of these practical realizations, Expert Systems (ES) has the greatest potential for meeting the decision-making needs of the manager in the ever-growing complex scoio-technical systems. Prof. Feigenbaum, an expert and leader on expert systems, has defined Expert System as"" ... an intelligent computer program that uses knowledge and inference procedures to solve problems that are difficult enough to require significant human expertise for their solution. Knowledge necessary to perform at such a level, plus the inference procedures used, can be thought of as a model of the expertise of the best practitioners of the field."""

Jan 1, 1989

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By John Millhiser, Stephen J. Kravits

The U.S. Bureau of Mines preproduction Wireless Survey System (WSS) and its performance during an in-mine test are discussed in this report. The WSS was developed to reduce downhole surveying time in order to increase the efficiency of drilling long horizontal methane drainage boreholes in coal. Borehole survey data are electromagnetically transmitted from the WSS7s downhole guidance probe, via the drill rod, to the uph&apos;ole subsystem in less than 1 min per survey transmission, regardless of borehole depth. The WSS7s in-mine test consisted of providing borehole survey data during the directional drilling of a 2,538-ft horizontal methane drainage borehole in the Pittsburgh Coalbed. By considering available drilling time, which does not include hydraulic drill downtime and the time spent traveling portal to portal, 24 shifts were needed to complete the borehole. Of the available drilling time during the tcst, 50 pct of the time was spent drilling and 50 pct surveying and maintaining the WSS to keep it operational. Previous Bureau experience indicates drilling efficiency was increased 108 pct because of the WSS, in comparison with using a commercially available wire-run directional survey instrument at 10-ft intervals.

Jan 1, 1990

By M. M. Tilman

The Bureau of Mines conducted research to determine whether it is possible to substantially improve the fatigue resistance of lead sheet by means of surface coatings. Five types of coatings were applied to unalloyed chemical lead sheet. Flexural tests revealed that the best fatigue resistance was obtained with coatings of vacuum grease. Vacuum-grease coatings on unalloyed lead sheet resulted in fatigue resistance at least as good as that of the fatigue-resistant alloy Pb-0.04 Ca. Coated lead sheet was also tested in short-time tensile tests and in tensile creep tests. Tensile and yield strengths were increased by several of the coatings with only moderate loss of ductility. Creep resistance was also improved in varying degrees by most of the coatings. The Bureau also conducted research on the effectiveness of noise barriers by using sheet lead in combination with other materials. Noise barriers consisting of continuous-cast sheet lead with gypsum board were found to be effective and relatively inexpensive barriers.

Jan 1, 1978