Search Documents

By S. D. Sanders

Goals of the Bureau of Mines include utilizing readily available minerals as substitutes for scarce mineral commodities and minimizing occupational hazards associated with mineral processing occupations. Therefore, the Tuscaloosa Research Center investigated using rapid-set cement as a suitable molding sand binder for small ferrous castings; currently petroleum-based binders are used. Substitution of a rapid-set cement would eliminate organic vapors associated with the petroleum-based binders; these vapors constitute occupational hazards and environmental pollutants. A binder containing 60 percent white portland cement (WPC) and 40 percent calcium aluminate (CA) would be an acceptable and economic substitute for petroleum-based binders where the foundry requirements are compatible with its limitations. It produced a set time and a pattern strip time of less than 1 hour. Cement, sand, and water mixtures developed compressive strengths from about 40 to 75 psi after 2 hours and from 120 to 130 psi after 24 hours. Tensile strengths of 18 to 22 psi were obtained after 2 hours, increasing to 30 to 35 psi after 24 hours. The addition of about 1 percent polyphosphate to the sand-cement-water mixture doubled the compressive strength and increased the tensile strength about 50 percent after 4 hours, but also increased the set time from 30 minutes to 1 to 1-1/2 hours. Po1yvinylacetate (PVA) resin latex additions resulted in rapid strength development. When castings were poured into the cement-bonded molds, the surface finish was fair to good on gray iron castings, but some areas of burn-on were present on steel castings. Using a graphite wash on the cement-bonded molds produced good surfaces on gray iron castings.

Jan 1, 1979

By Roy L. Wilfong

Infrared reference spectra are presented of compounds of importance in lead sulfide flotation research. Included are the spectra of several short chain alkyl xanthates of lead and zinc, the corresponding dixanthogen compounds, and the common oxidation products of lead sulfide and their sodium analogs. The spectra of several frequently used industrial flotation reagent xanthates are also presented. A thorough, well-documented discussion is given of the various corrections made to correct the as recorded absorption band data to near absolute values.

Jan 1, 1974

By R. A. Guidotti

The Federal Bureau of Mines has studied the reaction of oxides of columbium, vanadium, and tantalum with ammonia in vertical, gas-solids reactors at temperatures ranging from 300° to 1,300° C with the goal of preparing nitride intermediates for subsequent preparation of the metals by a thermal-decomposition step. The best nitride conversions were obtained in nonmetal reactors. With Cb205, V2O3, and V205 , low-temperature maxima in reaction rates occurred at 800°,800°, and 450° C, respectively, during oxynitride formation (in A1203) at 1 atm of pure ammonia. Conversion of the oxynitride, in a second step, to the mononitride was optimum at 1,200° C for columbium and 1,050° C for vanadium. In the case of Ta205, the rate of reaction to form Ta3N5 (in a single step) was highest at 900° C, where the presence of up to 5 percent methane was found to be beneficial; improved results were obtained by conducting the nitriding in a rotary kiln. Optimum space velocities (in the vertical Al203 reactor) ranged from 5,280 hr-1 for Cba205 to 7,950 hr-1 for V203. Oxide particle size had little effect upon reaction rates. Under fully optimized conditions, products containing less than 1 percent oxygen were readily obtained in under 6 hours.

Jan 1, 1975

By Donald A. Wilson

As part of a continuing effort to maximize metal recovery from domestic secondary resources, the Bureau of Mines investigated a process for recovering the metallic portion of scrap alkaline batteries. A pyrometallurgical method for recovering nickel and cadmium from Ni-Cd scrap batteries previously developed on a laboratory scale, was scaled up to 25-and 43-pound charges. The method employed reduction and/or decomposition in a retort using a minimum of 2.5 percent carbon as a reductant. Metallic cadmium was distilled at atmospheric pressure and a minimum of 900° C. Purity of the recovered cadmium was 99.8 percent minimum and the nickel-iron residue contained less than 0.02 percent cadmium.

Jan 1, 1981

By H. R. Batchelder

Much information on oxygen production and the manufacture of synthetic liquid fuels has been published during the past several years. From time to tine the investment and operating cost of oxygen plants of various sizes has been estimated. Surveys have been made so that the various processes by which oxygen is produced commercially might be compared. The gas-making processes in which oxygen is employed, which wore used in Germany during the war, have been described in T.O.M. reels, and this information has been published. Descriptions of pilot-scale or proposed commercial plants for the production of synthesis gas or hydrogen and their conversion to synthetic liquid fuels also have been published. In general, each of these publications has dealt with a particular phase of the over-all problem. The present paper will discuss the relationship between these phases: The factors that affect oxygen manufacture and costs, the methods for the use of oxygen and for the production of synthetic liquid fuels, and, to some extent, the economic factors that must be considered.

Jan 1, 1951

By Paul Biggs

This Bureau of Mines report provides information on 138 waterflood projects in Wyoming. Injection was in 25 producing zones and 65 fields. Specific data presented include field location, discovery and development, water supply and injection, oil and water production, estimates of oil in place, and oil recoveries by primary and secondary methods. The 138 projects studied will, if successful, recover about 800 million barrels of secondary oil. Almost all of the injection water is from deep water wells.

Jan 1, 1970

By Thomas R. Bur

Symmetry theory, based on ground work established in the study of single crystals and experimental procedures utilizing ultrasonic pulse velocities of spherical specimens plotted on equal area polar projections, enables the direct identification of a material's elastic symmetry system and the determination of its orientation, as well as the position of the elastic coordinate axes. The method is especially useful for elasticity studies of polycrystalline and amorphous materials for which this knowledge of symmetry is a prerequisite in determining the independent elastic constants. Projections based on theoretically derived velocities are given for a single crystal from each of the major crystallographic symmetry systems except the triclinic. Projections based on experimentally derived velocities are given for one brass and several rock spheres.

Jan 1, 1969

By Raymond B. Ladoo

The uses of talc are many but are not, in general well known or fully developed within the last decade several companies have realized the possibilities of greatly increased use and have intelligently proceeded to develop some of the fields which seemed most promising. This has had a tendency to lift talc from the obscurity in which it had existed for years, but the work is only started and much remains to be done. Considerably more attention has been paid to the technology and utilization of talc in Germany and Austria than in this country, despite the fact that the United States produces 65 of the world's talc and Germany and Austria combined but 5.4%. In the "Bericht,uber die tatigkeit des verbends der talcum-interessenten in Oesterreich-Ungarn" (Proceedings of the Austro-Hungarian Talc Association), for the years 1912 and 1913, many notes upon new uses appeared, together with suggestions as to further development of old uses. Aside from a few notes on the use of tar in paper, little has been published in the English language upon this subject. By recent action of the Talc and Soapstone Producers Association (U.S.A.) funds for research into the properties and uses of talc have been made Available and it is hoped that markets will be materially broadened a a result of this work.

May 1, 1920

By Miklos D. G. Salamon, Jim M. Galvin, Bruce K. Hebblewhite

A series of mine design accidents in the late 1980s resulted in a major research program at the University of New South Wales, Australia, aimed at developing pillar and mine design guidelines. A database of both failed and unfailed Australian underground coal mine pillar case studies was compiled. A procedure was developed to enable the effective width of rectangular pillars to be taken into account. The database was analyzed statistically using the maximum likelihood method, both independently and as a combined data set with the more extensive South African database. Probabilities of failure were correlated to factors of safety. It was found that there was less than a 4% variance in pillar design extraction ratios resulting from each of these approaches. There is a remarkable consistency between the design formulas developed from back-analysis of the two separate national pillar databases containing many different coal seams and geological environments.

Jan 5, 1999

By William J. Wiehagen

This is the third in a series of four articles that discuss underground fire-fighting preparedness. As with the first two articles, it is based on interviews with 214 miners conducted at 7 underground coal mines (referred to as Mines ?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996]. In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. The second article discussed miners? preparedness to evacuate a fire and their experience with incipient fires. In this article, we describe miners? experience in fighting underground mine fires and present their perceptions of training and readiness for fire-fighting.

Jan 1, 1997

By R. H. Nafziger

As part of its program to help decrease the dependency of the United States on foreign imports of nonfuel minerals and to devise technology for the efficient and economic use of domestic resources, the Bureau of Mines smelted and sulfation-leached an ilmenite from northern Minnesota. The objective was to assess the feasibility of preparing chlorination-grade titanium feedstock. The concentrate was smelted with woodchips, coke, and soda ash in 91-kg-and 1-metric ton (mt)-capacity electric arc furnaces to form Ti-rich slag and commercial-grade pig iron. The slag contained from 67 to 77 wt pct titanium oxides and from 1.8 to 7.2 wt pct iron. Sulfation occurred in a 4.5-kg/h moving-bed reactor using S02-air mixtures at temperatures of 8000 to 8500 C to form soluble salts of the Ca, Mg, Mn,and Na impurities, which cause plugging of fluidized-bed chlorinators. Subsequently, the sulfated slag was leached in acid to remove the soluble sulfates. The final product from small-scale testing contained up to 95.5 wt pct Ti02, a minimum of 0.6 wt pct Fe, and a minimum total of 0.3 wt pct of the four impurities of interest. The final product meets charge specifications for chlorination. However, more large-scale testing is necessary.

Jan 1, 1987

By B. S. Covino

The Bureau of Mines has conducted a laboratory and field corrosion test¬ing program to determine materials of construction for the leaching and gas-sparging crystallization environments of the clay-HC1 process in order to more fully utilize the alumina from domestically available kaolinitic clays. Laboratory tests were used to determine the corrosion rates of 22 metals and alloys by weight-loss measurements in these two environments of the process. The results of this laboratory study were used both to suggest metals and alloys for field testing and to determine the effect of the individual solution components on the corrosion behavior of the metals and alloys. Results from the field tests were used to recommend Ta, Ta-2.5W, and Ta-10W for con¬struction of the agitators for the leaching process. The metals and alloys recommended for construction of the gas-sparging crystallizer heat exchangers were Ta, Ta-2.5W, Ta-10W, Nb, Nb-1Zr, Nb-3Zr, Nb-28Ta-10W-1Zr, Nb-10Hf-1Ti, and Zr for the first stage and Ta, Ta-2.5W, Ta-10W, Nb-28Ta-10W-1Zr, Nb, Nb-10Hf-1Ti, and Zr for the second stage.

Jan 1, 1981

By Donald N. H. Chi

The unsteady, one-dimensional, compressible-flow equations have been solved numerically for a deflagration propagating through a gallery of finite length closed at the ignition end and open at the opposite end. These equations were solved for two situations wherein (1) the propagating flame was extinguished after 0.1 sec or before the return of aerodynamic disturbances reflected from the open end, and (2) the flame was allowed to propagate a full 0.8 sec until it was extinguished. It was found that the process of sudden flame extinguishment creates rarefaction waves that, upon entering the burned zone, produce resonance within the burned cavity. For the relatively small value of the product of the expansion ratio (8.5) and the effective burning velocities of 7.4 m sec-1 for the first experiment and 4.9 m sec-1 for the second experiment, it was found that the acoustic approximation provides an adequate estimate of the pressures developed ahead of the flame during the system's early history.

Jan 1, 1974

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United States and publishes economic data on the industry, based upon reports from producers. This publication lists all producers that reported commercial production to the Bureau for 1959. The companies named herein represent virtually all commercial producers of peat. A few companies, however, may not have been canvassed or failed to respond, as tine survey is voluntary For producers, arid the industry has many small operations that operate intermittently. No consideration was given to the quantities of peat produced and output of the various companies listed ranged from less than 100 tons to more than 50,000 tons, Peat is included in the Bureau's annual surveys of the mineral industries because, technically, peat is a fuel. Although none is used for fuel in the United States, peat is a potential source of energy and one of our large mineral resources. The domestic peat industry produces peat chiefly for use as a soil amendment. The industry has expanded rapidly during the past decade with active operations increasing from 45 in 1947-49 4/ to 105 in 1959. Output during this period has increased 218 percent, rising from 131,782 net tons to 419,460 net tons.

Jan 1, 1960

By R. E. Perry

In connection with a program of coal research at the Southern Experiment Station the Bureau of Mines, in cooperation with the University of Alabama and the various coal operators, conducts washability studies of coal from beds in Alabama and other Southern States in which commercially important deposits occur. One of the main objectives of a washability study is to obtain technically and commercially important data necessary for determining the best methods for preparing and utilizing the Nation's limited reserves of coking coal. Such information is important to conservation because it facilitates selection of preparation methods that will provide maximum yields of coal with low ash and sulfur contents.

Jan 1, 1958

By V. E. Erwin, W. W. Adams

"INTRODUCTION This report presents statistics of accidents at coke ovens in the United States during the calendar years as 1933, the twenty-first year for which data of this kind are available, 1913 being the first year for which accident reports were collected from the operating companies by the Bureau of Mines. The present report is presented in mimeograph form because insufficient funds are available for printing it. The first report of the Bureau of Mines that contained statistics of accidents for the coke-mining industry in the United States covered the two calendar years, 1913 and 1914. While the figures presented therein related both to beehive and by-product ovens, the original returns from the operating companies were not classified so as to permit the presentation of accident statistics for each class of ovens separately. Beginning with 1915, the accident reports from the operating companies have shown the general type of ovens to which the reports related; therefore, since that year, separate statistics for each of the two classes of ovens have been given in the Bureau's yearly reports of accidents at coke ovens.The coke-making industry in the United States established a safety record in 1933 almost equal in merit to that which it achieved in 1932, when the accident-frequency rate was the lowest and therefore the most favorable that the industry has known. Credit for the achievement is due almost entirely to companies operating byproduct ovens. (See table 8.)"

Mar 1, 1935

By B. Dimitriades

The Bureau of Mines measured the reactivities of 19 hydrocarbons known to be prominently present in automotive exhaust and ambient air in a smog chamber. Results agreed well with those obtained using two other smog chambers. Reactivity scales were developed for hydrocarbons and aldehydes using the results of this work and those of a previous study. Application of the reactivity scales to automotive exhaust samples gave fair agreement between predicted and observed rate-of-N02-formation values; however, predicted and observed ozone yields were neither in agreement nor did they correlate well. This lack of correlation for ozone yield was attributed to the inappropriateness of (1) the individual component reactivity data, (2) the reactivity classification scheme used, and (3) the linear summation method. In seeking to understand this problem and to develop more appropriate reactivity scales, the data were examined from a reaction mechanism standpoint, and further studies were suggested.

Jan 1, 1975

By Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine seals can be remotely constructed in underground coal mines, through vertical boreholes, when direct access to a fire is impossible or considered to be too dangerous. This method has great merit because boreholes can be drilled to specific mine areas and seals can be positioned close to a fire zone. The technology however, can be largely ineffective if the constructed seals do not provide effective barriers to airflow or cannot be used to impound water and other inert materials. Unfortunately, no viable alternatives exist to sealing the entire mine at the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Lake Lynn Laboratory (LLL). Under this effort, Howard Concrete Pumping Company and GAI Consultants, Inc. have joined forces to evaluate a potentially significant improvement to the current state-of-the-art. This paper will cover development of novel technology for remote mine seal construction, evaluation of the materials used, construction practice, and follow-up testing.

By A. Gene Collins

The Bureau of Mines conducted a research study of the geochemistry of the Smackover Formation to determine what geochemical relationships are useful in exploration for and production of oil and gas. Samples of oil, gas, brine, and rock were collected and analyzed. The oilfied brines were analyzed by methods recommended by the American Petroleum Institute and by tentative methods of the American Society for Testing and Materials. The crude oils were analyzed by Bureau of Mines methods; the gas, by Bureau of Mines methods; and the rocks, by wet-chemical, atomic absorption, and neutron activation methods. The results were correlated and interpreted, and several geochemical relationships useful in exploration and production were found. These include the type and class of brine, organic constituents in the brine, redox potential, in situ temperature and pressure of brine, degree of sulfate and carbonate saturation of brine, and halide concentrations in the brine.

Jan 1, 1974

By Andrew J. Fergus

A study of the flotation characteristics of columbium-tantalum minerals was made by contact-angle and microflotation methods, and the findings were confirmed by flotation of two natural ores. In the contact-angle study conditions for collection of columbite, pyrochlore, and tantalite were determined for (1) sodium oleate with a sulfonate; (2) sodium isooctyl phosphate; (3) a short-chain primary amine; (4) a long-chain primary amine; and (5) a quaternary amine. These conditions were confirmed in microflotation tests. Information about collector action on common gangue minerals was also obtained by these two methods. In batch flotation tests on a pyrochlore ore and a columbite ore, it was demonstrated that collectors selected on the basis of contact-angle and micro-flotation studies would float columbium minerals from a complex natural ore. However, multiple cleaner and scavenger flotation steps will be necessary to produce commercial concentrates. From a pyrochlore ore containing 0.54 percent Cb2O5, a 44.4 percent Cb2O5 concentrate was made containing 36.4 percent of the total Cb2O5. For a columbite are the corresponding values were: 4.35, 54.6, and 67.1 percent. During the batch flotation study, wetting agents were found to aid in the gangue-ore mineral separations.

Jan 1, 1968