Search Documents

By A. Visnapuu

The U.S. Bureau of Mines investigated the oxidation of American Iron and Steel Institute (AISI) Type 304 stainless steel (SS) during annealing in simulated combustion products from several air-CH4 fuel ratios. Atmospheres representing air-CH4 ratios of 14:1 and 18:1 contained free 02, while atmospheres representing 10:1 air-CH, ratio did not. A Cr203 layer formed on SS samples annealed in atmospheres containing free 0, while a Cr-Fe spinel layer formed in atmospheres with no free 02. The Cr203 layer was adherent and presented a protective barrier to metal diffusion, effectively limiting oxidation of the metal substrate. The Cr-Fe spinel was not protective and allowed the diffusion of Fe through the spinel to the gas-oxide interface where it was oxidized to magnetite, which spalled from the surface. This resulted in thick scale layers on samples annealed in atmospheres containing no free 02, as compared to layers formed on samples annealed in atmospheres containing free 02. These results confirmed and explained industrial operators' observations that thick, smoky (fine spalled magnetite) scales form on SS annealed in low free-02 atmospheres, while thin protective oxide layers form on sheets in atmospheres containing free 02.

Jan 1, 2010

By K. E. Stanfield

Asphalts from. Wyoming "black oils" are being studied at the Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming. These black oils are characterized by their high-asphalt, high-sulphur, and low-gasoline content and are difficult to refine by present methods into high-octane motor fuels, burning oils, and lubricants. Accordingly, their principal use, at present, is for the manufacture of road oil and asphalt. The present production of black oil could be increased to meet a greater demand. During 1937 the daily production of these crude oils in Wyoming was slightly over 13,000 barrels, while, the estimated potential production from existing wells was 56,000 barrels.

Jan 1, 1939

By Raja V. Rarnani, Robert L. Frantz

"The Generic Mineral Technology Center for Respirable Dust (GTCRD) was created at The Pennsylvania State University and West Virginia University by a congressional initiative in 1983 responding to recommendations in the 1980 National Academy of Sciences study on the Measurement and Control of Dust in Mines. Many of these recommendations dealt with the need to initiate focused fundamental research for further professional progress in dust control. Long-term, sustained support was emphasized to develop expertise in respirable dust research. In creating this Center, Penn State and West Virginia University were specifically recognized for their expertise in and facilities for research on coal mining and medicine. Today, the Center includes the Massachusetts Institute of Technology, the University of Minnesota, and the Michigan Technology University. The Respirable Dust Center is the only organization that coordinates and integrates the medical, scientific, and engineering aspects of respirable dust disease. The Center works with the U.S. Bureau of Mines (USBM), Mine Safety and Health Administration (MSHA), the National Institute for Occupational Safety and Health (NIOSH), the United Mine Workers of America (UMWA), and the U.S. coal industry in defining the research priorities for the programs of the Center to enhance research synergism.The Center's mission is to enhance the health, safety and productivity of miners by advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs to reduce the incidence and severity of respirable dust disease.All Dust Center activities are focused to be responsive to this mission, which is shared by the several federal agencies closely associated with the GTCRD. While significant progress has made mine atmospheres cleaner and healthier, respirable dust-related disease remains the nation's most pernicious industrial hazard.The goals of the GTCRD were formulated with recognition of the diverse scientific, engineering, and medical aspects of respirable dust, in addition to a need to enhance researcher interaction, as well as education and technology transfer efforts, in the respirable dust area. These goals reflect the needs of the mining industry as determined by the National Academy of Sciences Committee on Measurement and Control of Respirable Dust study done in 1980. The report of this committee encouraged the Bureau of Mines to redirect its research efforts ""...toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust."" The GTCRD's goals, detailed in chapter three of this document, were formulated to mesh with NAS recommendations."

Jan 1, 1995

By Frank W. Sansom

This paper is one of a series of articles dealing with milling methods and costs at metal mines in the United States, written in accordance with an outline prepared by engineers of the United States Bureau of Mines and published by the bureau. The Netta mine and concentrator is the largest of the plants of the Eagle-Picher Lead Co, It is located in Ottawa County, in the extreme northeast corner of Oklahoma, and in what is known as the Tri-State zinc and lead mining district, embracing the northeast corner of Oklahoma, the southwest corner of Missouri, and the southeast corner of Kansas. A majority of the production comes from the Oklahoma section, with Kansas second, and Missouri third.

Jan 1, 1930

By A. P. Grossman

'This report was prepared by Shell Oil Company, Mining Ventures Department in accordance with Cooperative Agreement No. 14-09-0070-b53 dated September 10, 1976, between the United States of America, Department of the Interior, Bureau of Mines and C(b) Shale Oil I Project, Ashland Oil Inc., Shell Oil Company, Operator. After completion of this report the Shell Oil Company withdrew from participation In the C(b) Shale Oil Project and advised the Bureau of Minus that plans for publication of this report had also been withdrawn. The Bureau of Mines acting under terms of the Cooperative Agreement hereby releases this report for general information.

Jan 1, 1976

By Emory Smith

The preface of the United States Bureau of Mines Manual of First Aid Instruction contains the following paragraphs: One of the most important inquiries that Congress has authorized the Bureau of Mines to conduct relates to health condi- tions among those engaged in the mineral industries. Investigations made early with a view to bettering these conditions demonstrated the need of prompt care of injured miners, as, under the difficulties inherent to mining and other mineral industries; wounds seemingly unimportant, if not treated promptly, may become infected and possibly cause permanent crippling or even death of the porach. In the past many seriously injured persons have been treated by fellow workers ignorant of approved means of treatment and transportation and have been handled in such a manner as to cause suffering and to accentuate injuries to such a degree as to bring about permanent disablement. Accordingly, the need of general instruction in first aid became apparent. It must be recognized that the conditions in and about the mines, mills, smelters, quarries, oil fields, etc., usually present difficulties not found in large industrial centers where experienced surgeons are available and hospitals close at hand. Many mines are isolated and, when an accident occurs several miles underground, there may be a serious lapse of time before the injured person can be brought to the surface and taken to the hospital or given attention by a sur- geon who may have to come a long distance. Under such conditions it has been frequently demonstrated that, if effective first aid is not given, the injured person may die or become permanently crippled... First-aid instruction has been found to be an excellent aid3in pre- venting accidents. In addition to the immediate relief of injured persons, it has been found that most persons while in the act of practicing dressings for

Apr 1, 1931

By John Gross

The Alaska Station of the Bureau of Mines has recently conducted tests on two tailings from black sand which had been treated previously at the Station. The results of this previous treatment have be on given in a paper entitled "Recovery of Gold from Black Sand by Classifier Concentration." The gold in these tailings was intimately united with quartz, and was so finely divided that it could not be detected with the naked eye, nor even by P&nn ing unless the material was ground. Its fineness is further shown by the assºy result, which reported only lz per cent of the gold content as "metallics", Wºorea's the assay of the original sand reported 36 per cent of the gold as "metallics." The fact that the gold was in such fine particles, closely united with quartz, precluded further recovery by amalgamation without grinding. On the other hand, the small content present, as well as the lack of grinding appliances at the placer mines of Alasia, made it necessary that the material be cheaply handled if at all. With these facts in mind the experiments described below were undertake.n.

Oct 1, 1920

By L. F. Willmott

Pulverized high-volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure-gasification pilot plant equipped for slurry feeding. The minimum ratio of water to pulverized coal that could be pumped satisfactorily as a slurry was about 1 to 1. Heating this slurry produced a suspension of coal in superheated steam having a steam-to-coal ratio greater than the 0.3 to 1 proportion that is considered optimum for pressure gasification of pulverized coal. A steam separator removed enough steam to provide ratios down to about 0.5 to 1, but a 0.3 to 1 ratio was not achieved. Gasification of Sewickley coal produced a synthesis gas containing about 36 percent H2, 46 percent CO, and 13 percent CO2, Gas output, gas composition, and coal and oxygen requirements were Virtually the same as for a pilot plant equipped for fluidized-coal feeding. Typical results from the slurry-fed plant at 300 psig were carbon gasified, 95 percent; coal requirement, 34 lb/M (thousand) std cu ft CO + H2 produced; oxygen requirement, 365 std cu ft/M std cu ft CO + H2 produced. The results showed that the two feeding methods are equally satisfactory from the standpoint of gasification. A choice between a fluidized-coal gasification process or a slurry gasification process depends on considerations relating to the coal-feeding phase itself, including capital and operating costs, manpower requirements, safety, and flexibility of operation.

Jan 1, 1962

By J. Hudy

An investigation has been made to determine the applicability of the Cendrex3 X-ray instrument for the measurement of the ash content of washed bituminous coal products. The results obtained for selected products from six preparation plants in the Appalachian region and one preparation plant in the mid-western region are described. Emphasis of the study was placed on low-ash bituminous coal products suitable for utility or metallurgical markets. There was good agreement between the results obtained by conventional ash determination methods and by ash determination using the Cendrex for all products tested.

Jan 1, 1968

By J. S. Walker

The Bureau of Mines monitored surface subsidence and water level fluctuations in 10 shallow observation wells above a series of four adjacent longwall panels in southwestern Pennsylvania, for about 4 yr. This study attempted to correlate the changes in the water levels within the observation wells to the measured vertical and horizontal ground movements associated with subsidence. Results of this study indicate that the fluctuation of the water levels appears to be a function of the well location relative to the mine layout and the proximity of mining. Wells are generally unaffected by mining of a preceding panel unless they are located within the angle of draw for that panel. Wells located at the centerline of a longwall panel exhibit the greatest fluctuation and head loss. This relationship may be related to the strain developed by the advancing longwall face. The water levels in the wells monitored fell at the greatest rate when the ground surrounding the well was in tension. The rate of the decline decreased as the dynamic development of the strains was changing from tension to compression. The water levels were found to be near the premining level before the ground was subject to maximum compressive strain. Nine of the ten wells investigated recovered to their premining water level after mining was completed.

Jan 1, 1988

By S. J. Broderick

[One phase of the general program for utilization of coal-mine waste led to the possibility of making a water softener from the material, as the waste matter contained both coal and clay and it is known that both these substances can be so activated as to exhibit distinct base-exchange properties. The carbonaceous]

Jan 1, 1941

By George S. Rice

"It is well known that the lost coal left in the ground in mining, under such conditions that recovery is practically impossible, constitutes a large proportion of the coal in the beds worked. A recent estimate, in a paper on ""The World's Fuel Supply"" presented by Prof. L. P. Breckinridge, of Yale University, before the Annual Meeting of the. American Society of Mechanical Engineers, places the average loss in bituminous coal mining as one-third left in the ground.The bald statement that there is a loss of one ton of coal for every two recovered may seem to those not familiar with coal mining to imply inexcusable and wanton waste. Perhaps a better way of expression is in terms of total recovery rather than in terms of losses. Many mine superintendents and mine owners will readily concede that their total recovery may be only 60 to 75 per cent, but to state that they are wasting 25 to 40 per cent arouses antagonism. The suggestion is of willful waste, whereas the majority of the operators try to the best of their ability to get a high recovery under the adverse and complex conditions that confront them. These involve natural, commercial, and labor conditions, and the requirement in many cases of boundary pillars under railroads and buildings, which may be called for in the deed or lease, or in the absence of specific exemption in the deed or lease, the common law requirement that a surface owner is entitled to the support of the surface."

Apr 1, 1921

By S. J. Broderick

[The authors gratefully acknowledge the assistance of O. C. Ralston, chief engineer, Nonmetals Division, Bureau of Mines, Who suggested the problem and Gave valuable aid during the course of the work. Thanks axe due also to Will H. Coghill, supervising engineer of the Southern Experiment Station, Bureau of Mines. INTRODUCTION One phase of the general program for utilization of coal-mine waste led to the possibility of making a water softener from the material, as the waste matter contained both coal and clay and. it is known that both these substances can be so activated as to exhibit distinct base-exchange properties. The carbonaceous]

Jan 1, 1941

By M. P. Ristenbatt, E. K. Holland-Moritz, K. Metzger

A new post-disaster signalling system for the Bureau o Mines, using through-the-earth EM propagation, was successfully field-tested in the Lake Lynn test mine. Successful detection at an estimated input SNR of -30dB was accomplished using a coherent integration time of 4.46 minutes. The transmitted waveform consisted of a repeating pseudonoise maximal length sequence phase modulating a 1950Hz carrier. The receiver used a sliding-window matched filter, optimal for signal known exactly except for phase and starting time, implemented via a special purpose processor. Parallel processing permits adaptive signalling, where the detection (integration) time is determined by the actual input SNR encountered. This field test demonstrates a trapped miner detection system that is about 36dB more sensitive than a current pulsed system. This increased sensitivity permits some desired combination of increased range, shorter detection time, and reduced transmitter power or antenna-size. The combination of pulse-compression-type-signal, coherent integration, parallel-processing, and output peak-detection algorithms permit implemention of an ultra-reliable detection system. The same combination is compatible with digital Pulse Position Modulation and Emitter position location strategies.

Jan 12, 1983

By N. S. Dalal, X. Shi

While it is known that vanadate and related compounds of pentavalent vanadium ( V (V)) exert potent toxic effects on a wide variety of biological systems, the underlying biochemical mechanism is still not fully understood ( 1- 3). One of the pathways is thought to involve the oxidation of NAD ( P) H. Thus, considerable effort has been devoted to finding the mechanism of NAD ( P) H oxidation by Vcvi (1-15). Erdmann et al. (5) first noted that vanadate stimulated the oxidation of NADH by plasma membranes and attributed this effect to a membrane containing NAD(P)H-dependent V(V) reductase. Later studies by Liochev and Fridovich indicated that endogenous superoxide ( 02 ) plays a central role in this reaction ( 4, 12, 13) . They proposed that NAD ( P) H dehydrogenases or oxidases produce 02, which causes VCV ) to stimulate NAD ( P) H oxidation via the following free radical chain mechanism ( 4, 12, 13) :

Mar 1, 1992

By Charles L. Kimbell

In overview, the world's mineral industry in 1989 registered gains over its 1988 performance, but these gains were by no means as pronounced as had been those of 1988. The traditional statistical measures of mineral industry performance, namely production, trade, and consumption levels, reflected significant growth in most industry sectors from crude material extraction through the gamut of down- stream processing. Growth in market economy countries generally exceeded growth in the centrally planned economy countries as a result of a variety of causes that will be covered subsequently, but even among the centrally planned countries there were some upturns. In contrast to these measures of the soundness of the industry, the situation for nonfuel mineral and metal prices was less satisfactory than in 1988, and low crude oil prices continued as a problem for the all-important petroleum sector, despite some gains during the year. The oil price situation mitigated against price increases for competitive fuels. Although this was unfavorable for fuel producers, it remained advantageous to consumers, including nonfuel mineral producers, processors, and transporters. Thus it cannot be viewed as a negative factor for the whole of the global mineral industry. Global crude mineral output value was estimated at nearly $1,420 billion in current dollars, an increase of 9% over the 1988 level, and an increase in current dollar terms for the seventh consecutive year. Measured in terms of constant dollars, however, adjusting for inflation, the increase was only 4.7% compared with the 1988 level. Despite the prolonged growth trend, the 1989 crude mineral output value level was still 3.2% below the record high set in 1980, which was $1,467 billion in terms of 1989 dollars.

Jan 1, 1992

By Leonard Obert

This report describes the development of a dynamic strain gage and a companion amplifier and recording camera -an apparatus designed to pick up and record the strain waves produced in rock by a nearby explosion. Also included in the report is a discussion of the relationships connecting the strain with the displacement, velocity, and acceleration for both plane and spherical waves. The proposed tests for which the strain gages were intended required making measurements in solid rock, a factor that necessitated the development of a gage that could be inserted and anchored in a small-diameter diamond-drill hole. The restriction on the diameter of the drill hole is required so that the presence of the hole in the medium will not influence the propagation of the strain wave. The gage should respond with fidelity to the frequencies present in a wave pulse generated by the nearby detonation of a small quantity of high-velocity explosive. Preliminary tests showed that this frequency range extends from 200 to 10,000 c.p.s. or greater. Also, the gage should be capable of measuring strains ranging from a few micro-inches per inch to several thousand micro-inches per inch. Other desirable design specifications included a low gage output impedance to permit the use of long cables, and a low gage cost, particularly in view of the fact that for the final design none of the gages can be recovered from the medium.

Jan 1, 1949

By Thomas M. Barczak

The safety of mine workers depends on the proper installation of roof supports to prevent the ground from collapsing into the working areas of an underground mine. As new support systems are developed, they need to be properly evaluated to make sure that they are capable of providing adequate roof support before they are first used in a mine. In addition to making certain that the supports meet basic safety criteria, the limitations of the support need to be fully defined in order to avoid improper application of a particular support design. The National Institute for Occupational Safety and Health (NIOSH) operates a world-class facility called the Safety Structures Testing Laboratory. This laboratory contains a unique load frame, the Mine Roof Simulator, which is capable of simulating the ground behavior in underground mines for conducting full-scale evaluations of roof support systems. Safety performance testing protocols using the unique Mine Roof Simulator have been developed for both standing roof support systems and longwall shield supports. The purpose of this paper is to describe these test procedures. The protocol for standing roof supports incorporates seven test series:( 1) uniform loading baseline tests, (2) height evaluations, (3) asymmetric loading, (4) biaxial loading, (5) load rate studies, (6) active loading determination, and (7) static loading evaluations. For longwall shields, a four-series test program that accurately simulates in-service conditions on a longwall face is proposed. This test program consists of (1) transfer of horizontal load to the caving shield-lemniscate assembly (zero-friction test),(2) point loading of shield joints due to lateral movement or rotation of the canopy, (3) evaluation of leg socketand leg cylinder integrity, and (4) face-to-waste racking of the shield. In addition, an evaluation of the shield’s hydraulic components will be conducted prior to the performance testing. These protocols will provide state-of-the-art safety performance evaluations of emerging support technologies, as well as a means to assess the safety of both new and aging longwall shields. Hence, this effort will enhance the safety of mine workers by ensuring that critical support elements are properly designed and that aging supports are retired before their support capability is jeopardized.

Jan 10, 2000

By Charles A. Seitz

This Bureau of Mines report describes an automatic and continuous transducer-drift compensator. The compensator formed a part of the instrumentation used to indicate the saturation by hydrogen of a cryogenic, adsorption column. It has a variable delayed-response characteristic and will respond only to signals having rise times faster than component drift times. Zero drift due to varying ambient conditions and component aging is nullified. Equations relating the output as a function of the input signal are given.

Jan 1, 1981

By David E. Emerson

An improved method and apparatus for determining the impurities in helium by preconcentration and subsequent analysis by mass spectrometry are described. Preconcentration of the impurities is accomplished by passing a known volume of helium, at slightly above atmospheric pressure, through a metal coil and trap assembly immersed in liquid helium. The concentrated impurities are then analyzed by mass spectrometry. This method can detect impurities in the range of 0.01 to 600 ppm with an accuracy of better than ±0.05 ppm at the 1-ppm level. One operator can analyze 15 samples in an 8-hour day.

Jan 1, 1970