Search Documents

The investment involved in any communication system represents a considerable sum. Even though it is desirable that the system work properly each and every time it is called into use, some failures are bound to occur. Most failures, however, and especially those that occur most frequently, are due to poor installation techniques. An extra hour spent at an installation site can save many maintenance trips and many frustrating hours of system troubleshooting. Typical faults likely to cause communication outrage are Pager phone systems Poor splices aggravated by corrosion. Strain relief not provided. Drip loop not provided. Incorrect branch connections. Overloading the circuit. Poor battery connections. Improper wire size or type. Lightning strikes. Improper placement of wire runs. Carrier phones Mounting transceiver near load resistors or other sources of heat. Tracks not electrically bonded. Cable abrasion due to poor mounting location. Disconnected battery. Poor mechanical installation. Each installation should be well planned. After an installation is completed, the technician should ask the question, "What can go wrong with this unit or line?" Remember the adage, "Whatever can go wrong, will." Preventive measures taken during installation will pay off in the long run. 6.2 Pager Phone Installation The pager phones used in many underground coal mines are battery-operated, party-line telephones with provisions for loudspeaker paging. The system is usually two-wire, nonpolarized, and operated by self-contained batteries. Many of the individual units are certified as permissible. 6.2.1 Mounting Pager phones are designed to be mounted on an upright support at the desired location. For convenience, the phone should be mounted 5 feet above the floor where there is no obstruction to using the handset or removing the cabinet front cover for servicing or battery replacement. In low-coal situations, a suitable height for installation should be selected convenient to the normal operator's position at the site selected. About 12 inches of free space on each side of the phone should be provided for cabinet access. The phone should be protected against direct exposure to dripping water and should not be allowed to rest in a puddle of water. The mounting location should be convenient to a work location and have a safe, unobstructed area for a worker to stand and use the phone. The phone must be in a location where the worker will not be in the path of moving vehicles or falling debris. Each telephone is normally well insulated, but it is still good practice to provide an insulating mat or dry planking for the user to stand on.

Jan 1, 1984

By R. D. Leitch

"INTRODUCTION The general program of the investigation of coal mine drainage which the Bureau of Mines is making includes, among its many phases and objectives, a study of the fate of the acid, content of drainage after it enters natural streams, and the effect of seasonal variations on the degree of contamination of streams. Opportunity for studying these under comparatively normal conditions and variations can readily be found, but there is only a chance opportunity for studying than under extreme conditions. The unusual drought that prevailed during the summer of 1930, however, created a condition of low water favorable to a study of one of the extremes.This report gives the results of an investigation of Bennett Branch of Sinnemahoning Creek, Pa., made under this condition.ACKNOWLEDGMENTSThis work was conducted under the direction, and with the advice, of Dr. R. R. Sayers, chief, Health and. Safety Branch, and of W. p. Yant, supervising engineer, Pittsburgh Experiment Station.DESCRIPTION OF BENNETT BRANCHBennett Branch, as shown in Figure 1, is a tributary to Sinnemahoning Creek. Its source is in Huston Township, northwestern Clearfield. County, from which it flows in a general northeasterly direction through Elk County, thenceeasterly in Cameron County to Sinnoning Creek at Driftwood. The total length is about 37 miles. There are nine towns along the stream that have an average population of about 350. There is no industrial pollution other that from coal mines and very little. domestic, pollution."

Jul 1, 1931

By Jack E. Tress

The Bureau of Mines has been involved for several years in the development of processes for the recycling of solid wastes. As part of this program, a project was initiated to determine the feasibility of producing secondary pig iron from auto scrap. During the test period, 86,000 pounds of shredded auto scrap, along with petroleum coke and fluxing agents, was charged to a submerged-arc furnace of 1-ton nominal capacity. Eighty-eight thousand pounds of pig iron, with an average carbon content of 3.90 percent and an average copper content of 0.2 percent, was produced at an electrical consumption of 512 kW-hr per net ton. A cost estimate of the process showed that the pig, iron might be produced at a cost of $57 per ton.

Jan 1, 1973

By Roy H. Grau, John C. LaScola

"This Bureau of Mines report contains a tabulation of methane emissions during 1980 for all coal mines located in the United States with emissions greater than 0.1 MMcfd. Listed for each mine are methane emission quantity, location, and coalbed. The report also compares records of 1975 and 1980 and describes relationships between emissions in 1980 and the Bureau's coalbed gas content data on 11 mines.INTRODUCTIONMethane gas is a threat to safety in underground coal mines. Research by Government and industry has led to great gains in reducing methane gas ignitions and explosions. The development of advanced methane control techniques is necessary for the safe operation of more gassy mines and the implementation of rapid mining techniques.As part of this research, the Bureau of Mines has surveyed total methane emission data from underground bituminous coal mines in the United States and tabulated emissions from mines producing over 0.1 MMcfd of methane. This report is an update of similar studies previously described in Information Circulars 8733, 8659, and 8558 (2-4).3The data from 1980 were compiled from Mine Safety and Health Administration (MSHA) records of air quality-quantity inspections made quarterly at each mine. The inspections involve measuring airflow and collecting air samples in the main returns. From these data, an average methane emission is calculated and used to represent the daily mine emission for each quarter. The methane emissions given in this report are the averages of the four 1980 quarters and do not include mine emissions from other sources such as degasification projects. Since a previous Bureau study showed that emissions from mines emitting less than 0.1 MMcfd represented only 2 pct of all emissions, 0.1 MMcfd was chosen as a lower limit for data collection (4)."

Jan 1, 1982

By John Taber, JOHN B. HOPKINS

During World War II , a critical shortage of domestic abrasive corundum developed . Late in 1944 , the shortage became so acute that it was deemed advisable to investigate certain low-grade corundum prospects in Madison and Gallatin Counties , Montana . The Gallatin , the Bozeman , and the Bear Trap deposits were the principal ones investigated . The Bear Trap deposit was examined by E. W. Newman and Robert S. O'Brien , engineers of the Bureau of Mines , in August 1944. Exploration was started in October 1944. Field work was completed late in the spring of 1945 . report presents the data obtained from the exploration .

Mar 1, 1947

By Thomas M. Barczak, Ron Smith

Steel liner plates, which are bolted together to form a shell, are commonly used to provide temporary protective linings in the tunneling industry to ensure the stability of the tunnel and safety of the workers until more permanent ground reinforcement can be installed. As the ground deforms to try and close the opening, the liner plate is radially stressed, and by deforming redistributes these loads back to the surrounding insitu earth. Grouting behind the plates is done to fill any voids and ensure uniform contact to the strata around the back of the plates. Another function of the liner plate in some applications is to act as a platform or structure for the mining machine to react against in order to develop the necessary forward thrust to be able to excavate the face. In this case, the liner plates are loaded axially as a horizontal column of bolted liner plate rings, creating a jacking force against the liner plate assembly. In general, the buckling strength of the plate sections determines the jacking force capacity. Historically, the jacking force capacity of tunnel liner plates has been theoretically determined by some simplistic equations developed from tests of single liner plates. Recently, full-scale tests on a complete circular section of bolted liner plate ring segments have been conducted in the NIOSH Safety Structures Testing Laboratory using the unique Mine Roof Simulator to apply controlled loading in a manner that simulates the real world environment. Due to the unique size and capacity of the Mine Roof Simulator, these are believed to be the first full-scale tests conducted on the jacking force capability of tunnel liner plate rings. These tests indicate that the previously used theoretical equations tend to over predict the jacking force capacity of these tunnel liner plates. Unanticipated deformations in the field have been observed at loads below these theoretical design loads, therefore, a more accurate determination of the jacking force capability was needed. This report summarizes the full-scale test results, examines design parameters that impact the jacking force capability, and develops new mathematical models to improve the prediction of design loads.

By A. Viksne

A series of tests were conducted by the Bureau of Mines to determine the best means of reducing noise generated by the detonating cord that is utilized for trunklines in quarry blasting. Ten different types of detonating cord were tested and evaluated for their acoustic qualities. The results of the investigation showed that noise levels produced by "low-core-load-per-foot" detonating cord "not covered" were lower than those produced by "high-core-load-per-foot" detonating cord covered with 6 inches of unconsolidated material.

Jan 1, 1972

By G. W. Jones, F. E. Scott

"INTRODUCTION As a part of its program of promoting safety in mining and other industries, the Bureau of Mines investigates the explosion hazards of combustible Gases, vapors, and solids. It also investigates various means and methods of controlling and mitigating explosions.Dichlorodifluoromethane, CC12F2, has been found to be very efficient as a quenching agent for methane flames. 4/ This substance is a gas at ordinary temperatures and pressures and is relatively nontoxic and stable at mod rate temperatures.Tremendous quantities of dichlorodifluoromethane were used daring the late war as an expelling agent for aerosol mixtures in ""aerosol bombs."" At one time during the war the demand for Dichlorodifluoromethane became so gent that there was barely enough of it to supply the Army and Navy and virtually none for civilian needs. During this period of scarcity the Bureau of Mines, in cooperation with the Bureau of Entomology, Department of Agriculture, investigated the possibility of substituting other materials in part for the dichlorodifluoromethane. It was required that the resulting mixtures be satisfactory expellant and noninflammable under all normal conditions of use."

Jun 1, 1946

By Oliver Bowles

"In a previous report of the Bureau of Mines (Serial No. 2080 reference was made to a fatal accident from falling rock in a quarry in Utah, and ways of avoiding such accidents were pointed out. A fatal accident similar to it in some respects recently occurred in a limestone quarry in Maryland. All operators of stone quarries are desirous of reducing accidents to a minimum, and almost without exception they welcome any suggestions having in view the establishment of safer quarry practice. It is believed, therefore, that a brief outline of the cir-cumstances surrounding this later accident may be of practical advantage to quarry-men, as it may serve as a guide to them in so conducting operations that such unfortunate occurrences may be reduced in number.The quarry where the accident occurred is in form a circular pit 500 to 600 feet across an 80 to 100 feet deep. The rock is a dense limestone with the beds dipping at an angle of 35 to 45 degrees from the horizontal. Numerous erosion cavities in the form of pockets or narrow spaces following joint planes are filled with red sand and clay. They are confined largely to the upper 20 or 30 feet of the deposit. Open bedding planes are 4 to 10 feet apart toward the surface, and are spaced at wider intervals toward the base of the quarry. The open bedding planes present smooth uniform rock surfaces that dip steeply into the pit at the northeast side of the quarry opening. These smooth surfaces constitute a source of danger, as they may permit loose material to slide into the pit.In this particular instance a blast had been discharged, throwing down a mass of rock for steam-shovel loading. Three men wore employed thereafter for a period of about two days in cleaning down all loose material that might be dangerous to workmen luring the loading process. A mass of red sand and clay in which several large bowlders were embedded was left on one of these slanting surfaces, for the material seemed to be sufficiently secure to be quite safe. The lower edge of the slanting surface was about 25 feet above the quarry floor. The quarry conditions are illustrated in fig. 1, where (a) represents the quarry floor, (b) the vertical quarry (c) the slanting joint plane surface, and (d) the rock and earth resting on the surface."

Dec 1, 1921

By Michael S. Miller

In 1984, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied the 34,050-acre Cow Creek Wilderness Study Area (WSA) in order to evaluate its mineral resources. The WSA, located about 60 miles southeast of Havre, MT, contains sandstones, shales, clays, and coal of Cretaceous age. The Cretaceous rocks have been intruded by ultramafic diatremes. Quaternary glacial, stream, and landslide deposits overlie the older rocks. Claims are staked at five of seven sites favorable for diamonds within the WSA and at additional sites nearby. Although the ultramafic diatremes within and near the WSA contain minerals that are indicators for diamonds, no positive evidence of diamonds was found during this study. An abandoned coal mine, the Shellenberger, is inside the southwest boundary of the WSA. Possible petroleum and natural gas at depth are currently of interest; land within the WSA is leased or under lease application for oil and gas. The WSA contains subeconomic clays, zeolites, gold, silver, platinum group metals, and coal.

Jan 1, 1986

By Fred Turin, Kim Cornelius, Lisa Steiner

NIOSH researchers have been examining underground coal mining activities in order to evaluate work crew hazards. In 1994 a continuous mining machine operator was killed by falling roof during extended cut mining. Many aspects of the incident were used by NIOSH researchers to develop a scenario interview. The goal was to provide a realistic framework for acquiring frank and detailed insights. The interview consists of two sections. The first describes the underground mining conditions. The second recounts the fatal incident. Each section is supplemented by a diagram and a set of questions addressing relevant safety issues. The interview was administered at three mines that actively take extended cuts. Researchers found the scenario approach to be an effective interview tool as well as an effective hazard awareness and safe work practices training platform.

By L. Cheng

This Bureau of Mines report summarizes an investigation of the amount of respirable dust adhering to the surfaces of seven run-of-face broken bituminous coals. The number of respirable-size (0.9 to 10 micrometers) particles adhering to the run-of-face coal ranged from 1011 to 1012 particles per pound of coal and was approximately inversely proportional to the mean lump size of the coal sample, otherwise it did not vary significantly with the coal seam, mining method, or winning machine. Based on these results, about 16 lb of ordinary run-of-face broken coal would have enough respirable-size adhering dust to contaminate 1,000,000 ft3 of air up to the 2 mg/m3 level, if this adhering dust should become airborne. Although brief studies here suggest that a negligible amount of new respirable dust is formed due to fracture of the broken coal during dropping, dislodging of old adhering particles during secondary handling operations is a potentially dangerous source of airborne respirable dust.

Jan 1, 1973

By Thomas J. Fisher, Thomas Novak

Strong circumstantial evidence suggests that lightning has initiated methane explosions in abandoned and sealed areas of underground coal mines. The Mine Safety and Health Administration (MSHA) investigated several of these occurrences within recent years. The investigated explosions occurred at significant depths, ranging from 500 ft to 1200 ft. Data from the National Lightning Detection Network indicate a definite correlation between the times and locations of the explosions with those of specific lightning strikes. This paper addresses the question, "Can lightning cause potential differences capable of igniting methane-and-air mixtures at overburden depths at which underground coal mining occurs?" A mine depth of 600 ft was selected for this initial study. Computer simulations were performed, with and without the presence of a metal- cased borehole extending from the surface to the mine level. CDEGSTU software from Safe Engineering Services & Technologies, Ltd (SES) was used for the simulation.

By Robert E. Meredith, Thomas T. Campbell

An investigation was undertaken to examine the feasibility of employing low- temperature nonaqueous baths for electrodepositing some of the refractory metals of the ferroalloy group . To date , such metals as tungsten , molybdenum , and vanadium have been produced only by high - temperature processes that are technically difficult and sometimes cumbersome in operation . Deposition studies were performed in a wide variety of organic solvents , including amides , ammonia derivatives , ketones , polyhydroxy alcohols , and ethers . Compounds prepared and used as solutes included the chloride and bromide salts of vanadium , tungsten , and molybdenum . Studies were conducted over a temperature range of 20 ° to 200 ° C under inert atmosphere . Conductivity and current potential data were obtained for all baths that contained reasonable solute concentrations . Qualitative solubility data were obtained for compounds of ferroalloy metals in a variety of solvents . In general , all solutes showed low solubility in ethers and ketones but reasonable solubility ( in excess of 20 grams per liter ) in alcohols , amides , and ammonia derivatives . No successful metallic deposits that would encourage further study were obtained with any of the systems that were examined .

Jan 1, 1963

By Roger J. Morrell

Disk-cutter experiments were performed on five rock types ranging in compressive strength from 9,000 psi to 27,000 psi. A specially constructed testing machine called a linear-cutter apparatus (LCA) was designed to load and traverse a free-rolling disk cutter across a sawed rock surface. The LCA was instrumented to measure the vertical and horizontal forces acting on the cutter during the run.. The ability of disk cutters to fragment rock was determined for both 60--degree and 90-degree cutting-edge angles, and relationships and regression equations were developed to predict cutter performance based on rock physical properties and applied forces,

Jan 1, 1970

By E. M. SEELEY, F. S. LOTT

Expansion in total capacity of the natural-gasoline industry.to produce light products continued in 1944 and 1945. The average rate of gain, however, was reduced to about 6 percent annually from over 9 percent in the preceding 4-year period. New facilities at cycle plants again accounted for most of the increase in productive capacity. Between January 1, 1944, and January 1, 1946, the number of cycle plants increased from 32 to 37 and their total capacity from 3,278 thousand gallons daily to 4,848 thousand (48 percent). Capacity of all other plants in the industry increased in the same period from 12,735 thousand gallons daily to 13,080 thousand, or only 3 percent. The capacity of the average plant increased to 28,600 gallons a day from 24,400 gallons on January 1, 1944, continuing the established trend. The average capacity of cycle plants increased to 131,000 gallons a day from 102,400 gallons, and the average capacity of all other natural-gasoline plants increased to 22,200 gallons a day from 20,400 gallons. Although the number of plants increased in only three States in the 2-year period (Texas, Okla- homa, and Arkansas), the total capacity of plants increased in eight States. A further decline of 29 reduced the total number of plants to 626 on January 1, 1946. Compared with 10 years earlier, gasoline plants were more numerous in only 4 States: Texas (48 more), New Mexico (7 more), Arkansas (2 more), and Louisiana (1 more). The largest declines, in order, were in Oklahoma, Illinois, Pennsylvania, West Virginia, and California. The number of plants with fractionating equipment for separating the liquefied gases from heavier fractions was 202 on January 1, 1946 and 182 2 years earlier. The principal changes in number and capacity of shut-down plants were an increase in Texas and a decrease in California. Shut-down natural-gaso- line plants are usually among the smallest units in their vicinity.

Apr 1, 1947

By C. J. Thompson

This Bureau of Mines study describes the preparation of sulfur compound concentrates boiling from 225° to 400° C, and reports the sulfur types detected in these concentrates by low-voltage mass spectrometry (LVMS). Existing LVMS methods were extended; the procedures described should be generally applicable to high-boiling petroleum distillates and concentrates as a preliminary means of narrowing the number of factions to be considered for more detailed separation and identification studies. The following major sulfur compound constituents of petroleum are indicated by the data: benzothiophenes, dibenzothiophenes, naphthanothiophenes, naphthenobenzothiophenes, and homologs and isomers of these. Cyclic and chain sulfides comprise a significant portion of the gas-oil range sulfur compound types. The presence of some classes of sulfur compounds containing two sulfur atoms per molecule was indicated.

Jan 1, 1966

By C. Kwong, L. H. Rorden, T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating, boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±15% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Ti tan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 5, 1978

By John Redington

This paper describing the milling practice at the Coniaurum Mine is one of a series of papers on milling methods, practice, and costs prepared in cooperation with an published by the United States Bureau of Mines. The 500-ton will of the Coniaurum Mines (Ltd.) is located at approximately the center of the company's property and a little more than a mile from the town of Schumacher, Ontario. The main shaft through which all the ore is heisted is adjacent to the mill so that the ore hoisted in a 3-ton skip is dumped directly into a 15-ton bin at the crusher.

Jan 1, 1931

By Launa G. Mallett, Barbara Fotta

This report examines the effects of mining height on injury rates in U.S. underground nonlongwall bituminous coal mines, controlling for both the employment size of the mine and the mining methods. Using the mine-level employment and injury data reported to the Mine Safely and Health Administration, mines were stratified by average coal seam height (<43 in, 43-60 in, and >60 in) and by the average number of employees working at the mine (<20 employees, 20-49 employees, 50-99 employees, and >99 employees). To reduce the confounding effects of mining method on injury rates, mines using longwall mining methods were identified and excluded from analysis. The employment data show that as the mine size increases, the proportion of hours worked in low seams decreases substantially. Additionally, miners injured in small, low- scam mines arc, on average, younger and less experienced than those injured in large high-seam mines. Nonfatal disabling and fatal injury rates were computed within each category of employment size and seam height for the major types of accidents (ground falls, powered haulage equipment, machinery, handling materials, slips and falls, and hand tools). Our findings suggest that, regardless of the employment size, as mining height increases, miners are at increasingly higher risk of injury from accidents due to slips or falls and accidents involving shuttle cars and falls of ground. As mining height decreases, miners are at higher risk 01 injury from accidents involving roof bolting machines, load-haul-dump types of powered haulage equipment, personnel carriers, and powered haulage conveyors. On the other hand, regardless of the height of the coal seam, miners working in large underground mines had higher rates of injuries resulting from accidents involving handling materials and nonpowered hand tools, but lower rates of injury from accidents involving continuous mining machines and lower rates of fatal injuries from falls of supported and unsupported mine roof. Finally, miners working at small mines in low or medium seams are at higher risk of being fatally injured by a ljll of unsupported mine roof. These findings suggest the importance of&apos; considering the working height of the mine, as well as the employment size of the mining operation, when developing intervention strategies to reduce injury risk to underground coal miners. Results also identify the need to further explore how mining height contributes to the frequency and severity of injuries.

Jan 11, 1997