Search Documents

By R. W. Huber

The successful development of a titanium prototype of the 81-mm. mortar base plate for the Army Ordnance Corps is outlined in this report. Information is presented dealing with forming, forging, and machining, welding and assembly techniques, and design changes relative to this prototype. INTRODUCTION The work of the Federal Bureau of Mines in making ductile titanium available2/ has resulted in the establishment of a new industry. Owing to its strategic importance and the combination of low density and high strength, titanium has received considerable attention as a structural metal. Titanium's favorable strength-to-weight ratio is of particular importance to the Army Ordnance for equipment that is transported by airplane or by foot soldiers.

Jan 1, 1956

By E. W. GOODWIN, V. F. Parry, J. B. Goodman, L. D. Schmidt, J. D. Davis, A. C. Fieldner, W. S. Landers, J. L. ELDER

The Heliopore process is essentially an arrangement that uses the waste heat in the exhaust gas of an internal - combustion engine to carbonize coal (noncaking ) or lignite . The gases distilled from the coal furnish fuel for the internal - combustion engine , which drives an electric generator . Thus the main products of the plant are electricity and char . A flow diagram illustrating the principles of operation of the Heliopore process is given in figure 1. The primary equipment consists of a carbonizing retort , gas cooling and scrubbing equipment, a gas storage holder, and an engine to burn the gaseous carbonization products . Coal is charged into the top of the retort while the hot gases from the engine travel upward through special ducts in the retort countercurrent to the coal flow . The hot gases never come into direct contact with the coal . Char is discharged at the bottom of the retort and hot gases at the top . The gaseous products resulting from carbonization of the coal are drawn off by an exhauster through the condensing and scrubbing equipment to take out tar and liquor , then to a gas holder , and finally are burned in a gas engine . The gas engine drives an electric generator and the engine exhaust gases are returned to the retort to carbonize coal . The entire process was intended to be continuous and self - sustaining, and to use coal as the only fuel . The plant may be said to be a large - scale pilot plant in that , although it is of full commercial size , its main purpose is to provide data for the design of others of its type . The installation tested had a daily throughput of about 4 tons of coal . Figures 2 , 3 , and 4 picture some details of the plant and equipment used in the experimental testing . Further details of the equipment and engineering drawings of the castings are shown in figures 8 to 22 in the Appendix .

Dec 1, 1943

By D. Harrington, M. W. Von Bernewitz

Sections 120 and 121 of Article XI. Fire Control, of a proposed Mine Safety Law in preparation, to be used as desired and when approved by any State, contains these provisions: After the adoption of these regulations, no mine operator shall erect any nonfireproof structure within 50 feet of any mine entrance. or airway. Every operating mine having nonfireproof structures within 50 feet of any mine entrance or airway, except headframes necessary for hoisting, shall have such structures fireproofed or removed and replaced with fireproof structures within six months of the adoption of these regulations. Before reopening, mines idle at the time of the adoption of these regulations shall have all non- fireproof structures fireproofed, removed, or replaced with fire- proof structures as required by the foregoing sentence. Upon receipt of the written statement of a mine operator that the fireproofing of existing structures is impracticable, the chief mining engineer (of the State commission) shall satisfy himself as to the abouracy of the statement. If he concurs that fireproofing is impracticable, and if at the same time he holds the opinion that adequate protection can be provided otherwise by such procedure, he shall have authority to issue a written permit for the substitution of fireproof door at or near portals of mine openings and collars: of shafts. Such doors shall fit as nearly gas-tight as possible. and shall be installed in such a way that the mouths of mine open- ings can be closed readily from outside of structures. The effec- tiveness of such permit may be made contingent upon the operator's continued compliance with any additional precautions which are necessary in the chief mining engineer's opinion to protect the lives of miners.

Mar 1, 1932

By E. J. Murphy

"INTRODUCTION This investigation is a continuation of previous work 3/4/5/ on the gaseous products of permissible explosives with and without sheaths. The range of oxygen balance of the explosives has been considerably increased. As has been shown previously, certain approximate relations exist between the volumes of gaseous products and the oxygen balance. Further systematization of the data is not feasible, since the method of theoretioal calculatln of the gaseous product is not yet satisfactorily developed. In a previously described method, 6/ it has been assumed that the explosion occurs at constant volume and that thermodynamic equilibrium is established. Apart from the presumably less important uncertainty of some of the thermodynamic data, it is not known how the confinement of the shots in the Bichel gage or the Crawshaw-Jones gage should be treated, or whether thermodynamic equilibrium is fully attained; nor can the extent to which the equilibrium composition changes during the subsequent period of expansion and cooling be judged with any reliability. Therefore, no calculations have been attempted. However, in anticipation of possible future theoretical interest and as an aid in answering practical problems, the new data are presented in the same minute detail as was done previously."

Mar 1, 1948

By Thomas M. Barczak

The effect of load rate on the load-carrying capabilities of wood cribs is investigated in this Bureau of Mines study. The modulus of deformation (stiffness) of wood crib blocks has been shown to increase with increases in rates of load application, causing larger load reactions for increases in convergence rates. Since wood cribs are tested in the laboratory at convergence rates that are orders of magnitude faster than typically would occur underground, wood cribs tested in the laboratory will react larger loads than the same cribs would react underground for the same displacement. Tests conducted in the Bureau's mine roof simulator on green wood crib blocks indicate that the increase in stiffness for increasing load rates diminishes at displacement rates beyond 0.1 in/min, making crib load nearly independent of load rate for rates faster than 0.1 in/min. Seasoned wood specimens were not as con-sistent in load-rate dependency. Some possible explanations of observed load-rate behavior on wood crib specimens are also postulated in this paper.

Jan 1, 1988

By D. Montagna

This Bureau of Mines report describes a salt-free, fluxless method for reclaiming metallic aluminum from aluminum dross. The dross is smelted under argon, nitrogen, or carbon dioxide, instead of a salt flux, in an externally heated pot furnace. Aluminum recovery, using argon, is equal to recoveries reported from commercial smelters that process dross in rotary-type furnaces This salt-free method could offer a reduction in air pollution, lower energy requirements by elimination of salts, and the production of up to 60 percent less solid waste for disposal than the salt method.

Jan 1, 1978

By R. V. Ramani, J. Qin, R. A. Jankowski

"Longwall mining is generally recognized as safer, more productive and economic when compared to room and pillar underground coal mining. There has been, however, increasing concern for the control of airborne coal dust concentrations in long wall faces. The airborne dust cloud at a longwall face is a complex aerosol system containing particles of varied size, density, shape and state of aggregation. For the development of more effective dust control practices in longwall faces, it is necessary to understand more clearly the characteristics of the longwall dust cloud.In this paper, results of a research study on dust concentration distributions along longwall faces are presented. The objective of this study is to characterize the longwall dust cloud behaviour and provide necessary fundamental data for a better understanding of the longwall dust problem. MSA personal samplers and gravimetric total dust samplers were employed to collect respirable and total airborne dust samples. The size distribution of these samples was determined by MicroTrac SPA. The instantaneous respirable airborne dust concentrations were recorded using RAM-I. The dust concentrations are related to face operations, particularly the shearer location and activities. The size distribution of airborne dust, instantaneous respirable airborne dust concentration, and air quantity distributions along longw all faces reveal a complex dust flow phenomenon. Additional fundamental studies are needed for characterizing the temporal and spatial behaviour of the dust cloud at longwall faces.IntroductionModern mechanized longwall mining was introduced in the United States in the 1960's and has become more common in the last twenty years. United States longwalls are multiple-entry retreating faces. According to a recent survey, 91 of the 102 longwall faces employ double-drum shearers (1). Several recently installed longwall faces have consistently produced over 4 000 to 5 000 tons per shift over extended periods of operation. The trend in under-ground coal mining in the U.S. certainly is toward the introduction of longwalls. This trend is true not only for new mines but also for renovation of existing mines. While longwall mining has many advantages over other mining methods, including improved safety, such as higher pro-duction. greater productivity and enhanced reserve recov-ery, it is associated with severe problems of dust control. The increase in longwall production has been accompanied by an increase in respirable dust problems which limit realizing the full potential of the longwall mining system. Despite the efforts to develop improved equipment and operational procedures to control the dust levels at longwall faces, it is still difficult to bring several double-drum shearer operations into compliance with the Federal stand¬ards of 2,0 mg/m 3 respirable dust without loss of produc¬tion. In fiscal year 1987, fifty-eight of the longwall sections were found to be in non-compliance once, and an additional 31 were cited two or more times'''. If the full potential of the longwall mining method is to be realized, new measures must be implemented to control the dust concentration to mandated levels. There is a need for detailed and extensive sampling of longwall faces to understand the dust source-sink relationships and the transient ambient concentrations. These must be related to the mining activities on the face. This paper is to characterize the longwall dust cloud behavior through a series of experiments in operating faces and provide necessary fundamental data for further studies to develop improved dust control practices."

Mar 1, 1992

By Allen D. Look, Alan A. Sharp

"Churn drills for blast-hole drilling are important to the operation of most open-pit metal mines, but certain hazards are created through their use that cause fatal and nonfatal accidents.2/ The purpose of this circular is to present a code of safe practice prepared and followed at a large Arizona open-pit copper mine, where safety is recognized as a definite operating problem. Such a code, based upon a thorough study of available published information as well as practical experience gained from accidents and near accidents, is the result of considerable effort and monetary expenditure. It is hoped that other operations using churn drills may benefit by the code presented, either in comparison with existing rules or in the preparation of new operating instructions.The code presented is in use at the Morenci Branch of the Phelps Dodge Corn., Morenci, Ariz. Similar codes are used at the New Cornelia Branch, Ajo, Ariz., and in the waste-pit operation at the United Verde Branch, Jerome, Ariz.The authors gratefully acknowledge the cooperation of the Phelps Dodge Corp., whose personnel made: possible the collection of information included in this circular. Special acknowledgment is due Paul Simmons, safety engineer, and 3. U. Larsen, general drilling and blasting foreman, Morenci Branch, Morenci, Ariz.The importance of churn drills in Arizona mining is apparent when it is realized that at all the open-pit copper mines blast holes are drilled with this equipment. At Morenci, approximately 98 percent of the ground is broken by primary blasting of churn-drill holes.There has been a growing tendency in Arizona's copper-mining industry to change from underground to open-pit mining, with consequent increase in the use of churn-drill blast holes for primary blasting.3/Thirty-three churn drills are in use at Morenci for blast-hole drilling. The drills operate with 440-volt alternating current, and trailing drill cables, in 500-foot sections, connect with the portable drill transformer station.4/ Three Diesel-driven churn drills for drilling prospect holes also are in use. About 25 churn-drill shifts are operated currently on a three-shift basis. Ordinarily, a two-man crew is assigned to each drill; however, with prospect-drill crews a third man is added to handle the sampling.Benches are carried at a uniform height of 50 feet. Churn-drill holes are 9 or 12 inches in diameter and about 60 feet deep. The holes are 18 feet apart in hard waste and 21 feet in soft waste and ore, with toes from 11 to 13 yards at the shovel grade. Both the hole spacing and the toe have been increased gradually, until they are now 2 yards longer than in 1940. The average ground broken per hole is 3,500 tons, or 60 tons of ore per foot of hole drilled. The holes are drilled 10 feet below the bench to avoid leaving hard bottom, which requires secondary drilling and blasting.Starting with a 12-inch casing, the prospect holes average 1,200 to 1,500 feet in depth and terminate with 6-inch casing; the deepest hole drilled to date went to 1,735 feet.In addition, churn-drills are used at Morenci to drill blast holes in the silica pit, limestone quarry, and the tailings dam. Other irregular applications are the drilling of holes to set trolley roles and for concrete piling in building foundations."

Jan 1, 1950

By C. H. Riggs

This report presents pertinent data on all active water-flooding projects in Washington County, Okla., and describes in detail the operation and production history of five representative floods. The flooding of partly depleted oil-bearing sands to produce petroleum that would not be recovered by other methods is becoming increasingly important to the oil industry. In 1942, two water-flooding projects in Washington County produced 35 barrels of oil daily from 90 developed acres. In March 1951, 4,000 barrels of oil was being produced daily by the injection of 58,000 barrels of water on 19 active projects covering 1,645 acres. Several projects are being extended, and new operations are being initiated. Figure 1 shows the location of the active water-flooding projects in Washington County. The yearly oil production from Washington County increased from 1,076,000 barrels in 1948 to 1,720,000 barrels in 1950, owing principally to the effects of water flooding. To March 1951, permits to flood more than 8,000 acres in Washington County had been granted by the Oklahoma Corporation Commission.

Jan 1, 1951

By Synthia N. McIntosh

The U.S. Bureau of Mines investigated the feasibility of using ammonium carbamate (NH2CO2NH4) leaching to recover manganese from steel plant slag. This investigation showed that treatment of the slag in hydrogen prior to leaching enhanced manganese extraction. Up to 80 pct of the manganese and 50 pct of the iron could be extracted from a silicon steel slag that had been pretreated in hydrogen at 700° C. Two 4-h leaching stages conducted at ambient temperature with a solution containing ammonia and carbon dioxide dissolved manganese and iron as their carbamate complexes. Heating the pregnant solution to 65° to 85° C decomposed the complexes and precipitated the metals as insoluble carbonate salts. Ammonium carbamate leaching of other slags from several steelmaking plants produced lower manganese extractions, which suggests that the method cannot be applied satisfactorily to all steelmaking slags

Jan 1, 2010

By Wesley T. Holmes II, Lloyd H. Banning

Electric - smelting studies were made on titaniferous materials obtained from the Klukwan and Snettisham , Alaska ; Choteau , Mont .; and Iron Mountain , Wyo . , deposits with the objective of determining the feasibility of producing pig iron and an enriched titania slag in one test series and pig iron alone in another test series . In addition , related studies were conducted to determine the amenability of Choteau crude ore to wet -magnetic separation and to determine the quality of steel that could be produced from the titaniferous pig iron . The continuous smelting tests were made in a three - phase , submerged - arc , electric furnace , and the laboratory steelmaking tests were made in a singlephase electric - arc furnace . A continuous , belt - type , wet - magnetic separator was used in conjunction with a ball mill and a spiral classifier in recovering titaniferous magnetite from the crude Choteau ore . Pig irons containing less than 0.05 percent phosphorus or sulfur were readily produced from the titaniferous materials ; iron recoveries ranged from 92 to 98 percent . The Choteau ore was ground to minus 65 - mesh to produce a concentrate containing 60 percent or more iron . The steel produced from the titaniferous pig iron was a high - quality product .

Jan 1, 1964

By G. R. Palmer

Preliminary studies by the Bureau of Mines were conducted to determine the feasibility of a multiple-compartment, ion-exchange (MCIX) column simulator for examining the effect of multiple-orifice plates in the column. A rectangular, five-orifice, three-compartment, MCIX simulator with a cross-sectional plate area of 0.66 ft2 was used for the investigation. Orifices with open areas of 1, 3, and 5 percent were used with various operating conditions. The study was separated into three separate sections: (1) solution flow effect, (2) fluidization effect, and (3) resin transfer effect. The solution flow and fluidization studies showed that for solution flow rates of about 3 gpm/ft2, a I-percent open area plate functioned best, while at solution flow rates of 9 and 15 gpm/ft2, the best open areas were 3 and 5 percent, respectively.

Jan 1, 1981

By W. T. Benson

The Bureau of Mines has examined selected deposits of titanium minerals throughout the United States. The titaniferous magnetite deposits in the western San Gabriel Mountains, Los Angeles County, Calif., were among those selected for study, and in 1956-58 field work was conducted to determine the extent and character of the titaniferous magnetite deposits occurring in the area. This report describes this work and summarizes earlier work in the area by the Bureau and others. The titaniferous magnetite occurs disseminated as seams and lenticular pods in an anorthosite belt 4 to 6 miles wide that trends about. N. 80° W., extending from sec. 13, T. 3 N., R. 12 W., to the west boundary of R. 14 W., at which point the titaniferous magnetite-bearing rocks disappear beneath the sediments in the Santa Clara River Valley.

Jan 1, 1962

By J. P. Capp

The Federal Bureau of Mines and the Alabama Power Company conducted an experiment in underground gasification of coal at Gorgas, Ala. involving the use of hydraulic fracturing to increase the air acceptance of a coalbed for the introduction of combustion air and removal of product gases. Air acceptance is defined as the flow rate of air which can be injected into the coalbed at 65 p.s.i.g. This was the second time the hydraulic-fracturing technique was used at Gorgas. Sand suspended in a heavy oil served as the fracturing fluid in the first experiment; in the second the sand was two to six times larger and was suspended in a water-starch gel. In addition to providing further tests of the underground-gasification process, the purpose of the second experiment was to determine the effects of the larger sand and greater volumes of a water-base fluid on (1) the extent of the fractured area, (2) the air acceptance of the coal, and (3) the rate at which a gasification path could be carbonized (linked) through the coal, and to compare these results with those of the first experiment. The coal was fractured by injecting 11,000 lb. of sand and 33,580 gal. of water and water-gel at 200 to 600 g.p.m. and 900 to 1,000 p.s.i. The fluid fractured the coal and the sand served as a propping agent to hold the cracks and crevices open. Pressures during the fracturing operation at test boreholes indicated that the fracturing fluid extended only about 150 ft. from borehole H, the point of application of the fracture. Injection of air revealed that the air acceptance of the coalbed within this e t was materially increased. On the other hand, increased air acceptance also was noted at boreholes up to 280 ft. from borehole H and at the electrolinking area 300 to 400 ft. away, indicating that the fracture effects extended considerably farther than was evident from observation. Similar effects were noted at approximately the same distances after the first hydraulic fracture.

Jan 1, 1961

By O. C. Blade

This report on the properties of motor fuels sold through service stations-in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Deparment of the Interior. It presents analytical data for 4,397 samples, representing the products of 130 companies. The samples were collected during December 1952 and January and February 1953. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past ten years is given on page 5.

Jan 1, 1953

By W. J. Crawford, P. M. Gruzensky

"Several experiments have been carried out in efforts to evaluate qualitatively a variety of electrolytes for refining bismuth. Most extensive work was done with the basic tartrate, hydrochloric acid, and hydrofluosilicic acid electrolytes. Deposits that are smooth and adherent can be obtained from these three electrolytes if low cathode current densities are employed. All three electrolytes were effective in purifying crude bismuth considerably, with additional purification indicated in each instance by a reelectrolysis step.With the basic tartrate electrolyte best results were obtained when the electrolyte was at 40° C. and contained at least 100 grams of bismuth per liter. An apparent disadvantage was depletion of bismuth from this electrolyte, causing the deposits to become spongy and nonadherent.The hydrochloric acid electrolyte had the greatest tendency to yield rough, dendritic deposits. Best deposits were obtained at cathode-current densities below 2 amperes per square decimeter. A small amount of glycerin helped to produce a smoother deposit, and adding sulfuric acid or methyl sulfuric acid retarded the deposition of impurities. Very good results were obtained in electrowinning bismuth from a bismuth trichloride-hydrochloric acid electrolyte.Smooth and adherent deposits were obtained from a hydrofluosilicic acid electrolyte, with very good refining as regards lead and silver impurities; however, higher reagent costs and slow decomposition of the electrolyte have discouraged its use.INTRODUCTIONMethods of recovering bismuth from ores and byproducts were underdeveloped for many years because of the limited uses for bismuth, the pharmaceutical industry being the chief consumer. In the past decade or so additional uses for bismuth, particularly in the metallurgical field, have brought about increased demand for the metal with the result that bismuth is being recovered from byproducts that were once discarded. In addition to such uses as low-melting alloys, solders, bearings, die setting, etc., some interest has been indicated in bismuth as a possible coolant for nuclear reactors. The advent of ductile bismuth and bismuth-alloy thermocouple wire has contributed greatly to temperature measurement, particularly in the below-zero range."

Jan 1, 1956

By N. S. Dalal, X. N. Hu, X. Shi, V. Vallyathan

"Although silicosis has been studied extensively, the mechanism is still not fully understood. Experiments do provide evidence that the actions of unique properties of silica surface on the cell membrane are the starting point of silicotic processes. This paper summarizes literature on chemical properties of silica surface, and the effect of particle size on silica toxicity. This paper also discusses the ways in which silica dusts are thought to interact with the cell membrane, with emphasis on freshness, hydrogen bonding, and free-radical interactions.INTRODUCTIONSilicosis is a debilitating pulmonary disease that afflicts persons (miners, foundry workers, ceramic workers, heavy construction workers, etc.) who chronically inhale silica-containing dusts (Schepers, 1960; Silicosis and Silicate Disease Committee, 1988). Since silica is second only to oxygen in weight percentage of the earth's crust (about 28%) and is found in an enormous diversity of minerals, it is natural that silicosis is one of the major industrial health hazards all over the world. Although silicosis has. been studied extensively, the mechanism by which the dusts exert their toxic actions on cells and the processes by which these actions progress to fibrogenesis are still poorly understood. The biological characteristics of the dusts are largely unknown, although it is suggested that the dust size, shape, surface charge, roughness, surface chemical composition, trace metal content, and crystallinity; dose of silica in the ambient air of the workplace; duration of exposure; genetic variation in exposed subjects; personal respiratory patterns; and presence of any coexisting disease (such as tuberculosis or rheumatoid arthritis) all influence the expression of silicosis (Koskinen et al., 1983; Noweir et al., 1980; Raask and Schilling, 1980; Reiser and Last, 1979; Thorne et al., 1985; Wolff et al., 1981). The actual biochemical mechanisms through which these factors operate are still unclear. However, the experiments do provide evidence that the actions of certain unique properties of silica surface on the cell membrane are the starting point of the silicotic process (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Marks, 1957; Parazzi et al., 1968; Reiser and Last, 1979; Summerton et al., 1977). This article summarizes literature on chemical properties of silica dusts and how silica dusts are thought to interact with the cell membrane, with emphasis on hydrogen bonding and free-radical interactions."

Jan 1, 1989

As part of its regular program to provide timely information on domestic mineral commodities, the Bureau of Mines conducted an engineering appraisal of more than 1,300 lode and placer gold deposits in the United States to deter-mine their gold production potential. While these deposits were estimated to contain over 400 million ounces of gold, only 9 million ounces, or slightly more than 2 percent, was found to be producible at $35 per ounce under prevailing mining and metallurgical technologies. The study revealed that any significant increase in available gold in the United States is most likely to come from the discovery of new sources, intensive exploration and development of the more promising known mineralized areas, and development of new or improved mining and metallurgical techniques.

Jan 1, 1967

By J. F. McIlwain

As part of its goal to minimize the requirements for critical materials, the Federal Bureau of Mines has investigated the consolidation of an iron-base superalloy (20 pct Cr, 5 pct each Ni and Mn, 1 pct each C, W, Mo, and Cb, and the balance Fe) and its modifications by powder metallurgy (P/M) techniques. Vacuum-atomized, prealloyed powder was used. Consolidation was by sintering of cold-pressed alloy powder, or by forging plus rolling or extrusion of canned powder. Several commercial lubricants were evaluated in the pressing operation. At 50-tsi compacting pressure with up to 3 wt-pct lubricant, green strengths did not exceed 1,000 psi. Powder sintered just below the solidus temperature attained a tensile strength of 69,000 psi and 4 pct elongation. Liquid-phase sintering produced higher densities, lower tensile strengths, and nil ductility. Canned powder was forged and rolled at 1,200° C, yielding a 100-hr rup¬ture strength of 9,800 psi at 815° C and a room-temperature tensile strength of >130,000 psi at 6 pct elongation. Heat treatment of modified P/M iron-base alloy containing 0.63 pct C resulted in a 100-hr rupture strength of 17,000 psi. Oxidation resistance at 805° to 815° C of the forged and rolled P/M iron-base alloy was similar to that of the cast iron-base alloy and supe¬rior to conventional stainless steels.

Jan 1, 1981

By E. K. Stanek

This report contains results of two major efforts related to electrical transients on mine electrical power systems. The first area concerns the use of digital computers to model mine electrical power systems and predict transients or duplicate field recordings of transients. Two existing general purpose circuit analysis programs were used. The first was the TRW Engineering System Simulator or TESS. The second was Electronic Circuit Analysis Program or ECAP. TESS proved to be superior to ECAP in several important characteristics, including system size limitations and modeling nonlinear elements. The second major topic covered in this report is the evaluation of commercially available surge suppression devices. These devices were found to be quite acceptable and guidelines for the selection and placement of surge suppressors were included. The final important item is a listing of the worst-case transients, from a design point of view, for ac and de utilization systems and ac distribution systems.

Jan 1, 1979