Search Documents

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By M. S. Moats, F. Elnathan

"The effect of current reversal on two commercially manufactured electrodes (RuO2-TiO2 and IrO2-Ta2O5 coated Ti) in a chloride bearing electrolyte was evaluated. Accelerated lifetimes were found to decrease with increasing current density and increasing reversal frequency. Ru: Ti coated electrodes exhibited longer lifetimes than Ir: Ta coated electrodes even though they had one-third as much precious metal content. Chloride concentration did not affect lifetime in the range examined. Using energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS), the failure mode of the electrodes was determined to be coating dissolution leading ultimately to passivation by the presumed growth of a highly resistive oxide at the coating/substrate interface.INTRODUCTIONCatalytic titanium anodes (CTAs) were developed in the 1960’s to replace graphite anodes in chlor-alkali cells. CTAs exhibited much better dimensional stability than graphite leading to lower operating potentials by promoting smaller electrode gaps and better operational efficiencies as they had to be replaced less often. CTAs are simply Ti substrates coated with precious metal oxides (such as IrO2 and RuO2) mixed with other components (such as TiO2 and TasO5) (Trasatti, 2000).CTAs are used in many other electrochemical industries, including water disinfection, wastewater treatment, cathodic protection and metal plating. RuO2 based coatings are typically used for chlorine evolution. IrO2 based coatings are for the most part utilized for oxygen evolution (Comninellis & Nerini, 1991; Forti, Olive, & De Andrade, 2001; Kotz, Stucki & Carcer, 1991; Trasatti & Lodi, 1981)"

Jan 1, 2016

By T. A. Apelt, B. J. Elliot

"In September 1993, the flash furnace at Kalgoorlie Nickel Smelter, KNS, was brought off line after almost 12 years of operation. This is a record campaign life for a flash furnace. The furnace was' totally rebuilt and the capacity of the plant increased from 540 000 tpo to 750 000 tpa of concentrate throughput. The throughput increase was' achieved through the construction of a 525 t/day oxygen plant and upgrading of various plant ancillaries. A number of significant design modifications were also built into the flash furnace and oxygen enrichment was implemented in the operation of the Peirce-Smith converters.This paper discusses the rebuilding of the flash furnace and design modifications made to furnace equipment and ancillary plant. Some preliminary post-startup operating data are presented.IntroductionIn September 1993, Campaign 6 of the flash furnace was concluded and the furnace brought off line for rebuilding. The campaign length was almost 12 years and set a new record for campaign length. Planning for the rebuild took place over the last five years of the campaign. A number of modifications to the design of the furnace and the ancillary plant were planned to coincide with the furnace rebuild. The furnace was rebuilt and recommissioned in 70 days. The increased plant capacity of 750000 tpa has been achieved by the construction of a 525 t/day oxygen plant and modifications made to ancillary plant which centred around increased p~ control, efficiency and hygiene. This paper examines the development and implementation of the modifications made to the furnace and ancillary plant. Preliminary post-shutdown performance data are presented."

Jan 1, 1995

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (An5-10); chessboard albite (An0-10); ""irregular albite "" (An0Ab100 to Ab90Or10); untwinned ""anoralbite"" (Ab90Or10 – Ab70Or30); and orthoclase (Ab40Or60 - Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (Ab5-10); chessboard albite (An0-10) "" irregular albite "" (An0Ab100 to Ab90r10); untwinned "" anoralbite"" (Ab90Or-Ab70Or30); and orthoclase (Ab440Or60-Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By Horace Freeman

Introduction In the aggregate, directly and ?indirectly, the pulp and paper industry ? consumes very large quantities of a variety of minerals, or compounds prepared from minerals. This is especially true in the manufacture of news-print, but fine papers, also, account for some of this consumption, in the processes of loading, coating, and otherwise improving the finish. The more important of the minerals used in the industry in Canada are briefly dealt with in the following pages. The list is by no means exhaustive, however. Thus, barite, lithopone, zinc oxide, zinc sulphide, and titanium oxide are used in small quantities in Canada in filling and coating paper. Up to the present time, however, the quantities of these materials used in the paper industry have not sufficed to encourage their manufacture in Canada. In the case of barite (barium sulphate)-or of witherite (barium carbonate)-it may be said that, should deposits of commercial size be discovered in Canada, the ore would have considerable export value, for use in the paper and other industries. China-Clay (Kaolin) Considerable quantities of china-clay are used for brightening and improving the finish of paper, and there is a growing tendency to use larger amounts of this material in newsprint manufacture. No china-clay suitable for paper manufacture is at present produced in Canada, but samples have been forthcoming recently from a deposit near St. Remi d'Amherst, Labelle county, Que., about thirty miles north of the Ottawa river and approximately midway between Montreal and Ottawa, and plans are under way to conduct large-scale tests with this material. Present sources of supply are the United States, England, and Russia.

Jan 1, 1934

By E. A. Collins

I TAKE it that the papers presented tonight on the subject of Reconstruction, as regards both gold and base-metals, are intended primarily to stimulate discussion of this important subject and, in regard to base-metals in particular, cannot in any manner be considered as a policy or plan to be followed as a panacea for all the ills which are bound to beset the industry when peace is declared. A famous cook-book written by a Mrs. Beeton contained a recipe for jugged hare which began with the instruction, "First catch your hare". To date, we have not caught the hare of victory and it may seem to many that any thought, energy, or effort devoted to the problem of reconstruction which will in any way impede the acceleration of the chase after victory will leave us open to the charge of being derelict in our duty as citizens. Much of our present trouble is due, however, to our lack of preparation for war in time of peace, and it follows that it is of equal importance in our national economy to prepare for peace in time of war. Most of us here tonight have vivid and sad memories of the chaos in the metal mining industry following the Great War of 1914-1918. In our own industry, mining, smelting and refining of nickel and copper, it was not a problem of absorbing the men who returned. There were only some three hundred who came back to the Mining and Smelting Division, and these men were all given their former jobs without any apparent difficulty. They were rehabilitated gradually due to the fact: that some of these men did not return for a year after the Armistice was signed. The numbers of men involved in the present conflict are much greater. We have to date in the armed forces upwards of 3,000 men enlisted from our employ.

Jan 1, 1943

By L. Torres, C. S. R. Rondestvedt, M. Bustos

In February 2010, Teck’s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

By P. A. Christopher, R. H. Pinsent

"The Adanac molybdenum porphyry deposit near Atlin, in northwestern British Columbia, was discovered in 1905. It was explored extensively between 1967 and 1980.The deposit is within a complex, multi-phase, quartz monzonite stock that is a satellite of the post-accretionary, Surprise Lake Batholith. Biotite K-Ar dates range from 703 ± 2.4 Ma to 71.6 ± 2.1 Ma, indicating a Late Cretaceous age of emplacement.The deposit comprises an irregular-shaped ring or halo peripheral to a quartz monzonite porphyry dome, or ""cupola': The shape of the ring, and of a smal~ fine-grained quartz monzonite intrusion, and the presence of higher-grade mineralimtion on the eastern flank of the cupola, suggest partial control by a preminera/ structure. The deposit is truncated by a steep, northwesterly dipping, normal fault (Adera Fault) that down-dropped the northern half of the deposit by a minimum of 100 mThe deposit lacks strong zonal alteration but there are narrow envelopes of potassic alteration around some veins and local zones of intense wall-rock silicification. There is considerable retrograde alteration along postminera/ faults and fractures.Molybdenite occurs in veins and fractures, many of which are relatively flat-lying. They occur in all phases of quartz monzonite. Molybdenum is the only element of economic significance. There are vein and skarn occurrences with tungsten, tin, lead, zinc and precious metals peripheral to the deposit.In 1981, Placer Development Limited reported an ""undiluted mineable mineral reserve"" of 151 971 000 tonnes grading 0.063% Mo at a cutoff grade of 0.04% Mo and a strip ratio of 1.5:1."

Jan 1, 1995

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973

By W. L. Strand, D. N. Madge

"Experimental and pilot operations in bituminous sand processing require due care and attention in the design and analysis of measurement programs. This paper deals with a case study in experimental design and data analysis for a series of experimental campaigns that have been conducted over the past five years by Kilborn Western Inc., acting on behalf of Bitmin Resources. Beginning with the design of the experiment and following into the use of linear and nonlinear regression models, the phenomenology of bitumen extraction is illustrated. The final testing program tested 13 oil sand types as well as a wide range of process variables for all the unit operations of the complete process.The program was successful in developing process fundamentals and scale-up criteria. Several phenomenological models were proposed and tested. Their range of applicability was explored. This paper illustrates the range of applicability of these models and discusses the development of alternative models.IntroductionOver the past five years Kilborn has conducted a series of bench scale and pilot scale experiments designed to explore the phenomenolgy of a new concept in medium temperature processing of bituminous ores. These experiments at feed rates ranging from .1 to 24 t/h were conducted on water wet sands from the .Athabasca region near Fort McMurray. They were based on experimental designs chosen to provide a systematic means of identifying the response surfaces of the process over a range of conceptual designs. The following diagram shows the experimental arrangement:"

Jan 1, 1998

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By J. Farrell

The Canadian government ratified the Kyoto Protocol in December 2002 and, prior to ratification, committed to equitable distribution of the burden of implementation. The Federal government's Large Final Emitters group is working with industry to develop covenants that will consider the unique nature of the company's operations and not unreasonably burden any one sector or company. Ensuring equitable distribution must consider local, national and international issues. From a Canadian iron ore producers perspective, the fact that most of the iron ore production in the world is in countries that have no Kyoto commitment is a critical issue. Another issue unique to this sector is the increased addition of fluxing agents in iron ore pellet production which has shifted some process related greenhouse gas emissions from steel producers to iron ore producers. While the objectives of the Kyoto Protocol are primarily environmental, the economic implications for Canadian industry are not trivial. For decades Canadian companies have been actively improving energy efficiency and reducing greenhouse gas emissions to maintain a global competitive position. Production of iron ore pellets is an energy intensive process and the Iron Ore Company of Canada (IOCC) is the largest Canadian producer. In 2002 IOCC identified energy and Kyoto Protocol implementation as critical risk factors for their organization and appointed a full time Energy Manager. In January 2003, IOCC initiated a comprehensive process for identifying energy cost reduction opportunities and established an Energy Master plan. This process included:

Jan 1, 2004

By John C. Loretto

"Answers to some of the problems ofRecovery and Metallurgical AccountingIn Gold and Silver Hydrometallurgical PlantsThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the Metallurgical Test work figures and secondly, the Metallurgical Accounting figures do not balance.The plant results not agreeing with testwork figures are mainly due to:a) The testwork samples were not representative of the eventual plantfeed;b) Misinterpretation or misunderstanding of testwork;c) Plant losses;d) Plant design not allowing testwork results to be achieved;e) Operating deficiencies.a} The testwork samples being dissimilar to the plant feed occurs on a very high proportion of projects. The effects of this can beccr.ie exaggerated because the upper levels of the mining company often regard the original testwork figures as sacred and therefore base their judgement of current plant performance on these figures.Frequently the test work samples represent only a minor part of the orebody or alternatively a single composite of the whole ore body is used for the testwork long before it has been determined that all of the potentially different ore zones behave in the same manner. These errors can be compensated for by repeating the ""testwork tests 11 on current plant feed on a routine basis and using these tests to determine whether or not the plant is operating satisfactorily."

Jan 1, 1982

By A. C. Moerman, C. W. Pelley, K. R. Notley

"The software package described in this paper facilitates the handling of diamond drilling information in the creation and maintenance of a geological information database. Once entered, the drilling information is stored in a direct access file for rapid retrieval. The drill data are sorted into vertical cross sections and interpretation is performed using on-screen menus to define areas of common rock type and outline the mineralized zones. Intersections of individual zones can then be examined and outlined in the longitudinal dimension at a graphics terminal.With the aid of surface-fitting routines, the digitized information can be used to generate three-dimensional models of each zone. From these models intermediate cross sections and level plans can be obtained. Several interpretations are possible and plotter drawings can be obtained. An output file for use by ore reserve estimation software can also be created.Future work will tie this software to geostatistics and mine planning programs and will be aimed at converting mainframe software to run on microcomputers. IntroductionComputer applications in underground mine planning and geology are not new. Operations such as Sherritt Gordono and Kidd Creek have been using software developed about a decade ago for handling geological information and designing stoping blocks. However, general use of such systems has been limited mainly due to the cost of hardware which was affordable only to large corporations. Software to perform the work was usually developed on site and was largely unavailable for use by others, being site-specific, or too expensive for other organizations to purchase.The increasing power of microcomputers and mini-computers, and their relatively low cost compared to the mainframe computers which were previously used, has led to the increased use of computers at mining operations of all sizes. Sources of software for use in geological interpretation and mine planning have increased in number with the proliferation of the use of microcomputers."

Jan 1, 1988

By M. Korchynsky

"The key words which characterize vanadium are: unlimited availability, versatility of applications and price stability. The supply of vanadium is assured by diversified sources, distributed all over the globe. The inexhaustible raw materials base is complemented by a strong vanadium industry. Both the fully integrated vanadium producers and converters of vanadium oxide or vanadium-containing slags or residues guarantee an adequate supply, commensurate with the steady growing demand.The major share of the world's vanadium output is being consumed by the steel industry. As an additive to steel, the versatility of vanadium is particularly impressive. A few hundreds of one per cent of vanadium convert plain carbon steel into high-strength, low-alloy steel with more than double strength. On the other extreme, high-speed steels made via the powder metallurgy route show superior performance with vanadium additions as high as 6 or 8 percent. Vanadium is used as a cost-effective alloying addition in steels for high-temperature service, fully alloyed heat-treatable steels, new dual-phase steels for automotive components, rail steels, etc., to mention only a few applications. Vanadium is also an established essential addition for titanium alloys. The chemical industry is relying on vanadium compounds as important catalysts.In spite of a wide diversity of applications and continual growth in consumption, vanadium has exhibited, over the past several decades, a remarkable price stability, free of conjunctural fluctuations. Because of its availability and versatility, it will continue to be one of the key metallic elements for future technologies.Key Features of VanadiumIn attempting to single out the key features of the metallic element vanadium, three descriptive characteristics come to mind: availability, versatility and price stability."

Jan 1, 1982

By Giles St. Pierre

"The purpose of this paper is to report in a general way on the use of the Portaspec X Ray Spectrograph.At Manitou Barvue, we are milling two types of ores, copper and zinc. The control assay practice was to take grab samples at 4 hour intervals. These samples were dried in the mill, then taken over to the Assay Office where two operators would process them. Three hours later results were available at almost the same time as the operator was ready to take his set of grabs again, leaving no time for adjustments, if any were needed.After a reduction of personnel, there were no assays available on night shift. This practice was slow and inadequate, and a new way of doing control assays was investigated.After investigation the Portaspec was found suitable for the type of operation that we had in mind. The Portaspec is a conventional dispersive type of X Ray spectrograph. The instrument consists of three parts:The Power Supply The Spectrographic Head The Digital ScalerIn our case, where dried powder samples are analyzed, the instrument was provided with a two sample holder using one for the standard and the other for the sample. The operation of the instrment does not require any degree of skill or knowledge of chemistry or spectrography.Previous to buying the instrument, six sets of six to ten samples were sent to the supplier along with the assay for each sample. These samples were Cu. HDS., Cu. Conc., Cu. tls, - Zn. HDS., Zn. Conc., Zn. tls. A definite pattern was observed. For example - six Cu. HDS. samples ranging from .40 to .90 gave 10400 counts for the lowest to 16.040 counts for the highest. The number of counts were then plotted to give percentages."

Jan 1, 1971

By Craig Ford

Inmet Mining is committed to implementing the highest corporate responsibility standards in its mining operations worldwide. Inmet is 100% owner of Minera Panama, a world-class copper project that is currently in the feasibility phase in north-central Panama. Panama has limited experience with modern mining, limited mining capacity, and the project context involves significant social, environmental and political complexity. The Project area is remote with recent in-migration of latino and indigenous people, informal and small-scale mining, local subsistence populations and considerable biodiversity value, coupled with a complex jurisdictional setting. In short, it is increasingly the kind of project mining companies are taking on because the easy projects have already been developed. With such challenging conditions, anticipating and managing social risks is critical to effective project management. To this end, between August 2007 and the third quarter of 2009 Inmet seconded Monkey Forest Consulting Ltd to the project to assist Minera Panama in building and implementing an effective, early phase external relations strategy. The team was also tasked to find and develop a locally based team that could sustain success through project development and into operations. Today?s presentation was created by Inmet and Monkey Forest and describes some of the lessons learned in implementing an effective early phase process for managing social issues.

May 1, 2010

By I. R. Muirhead

"One approach to making new technology available is to demonstrate its value under full-scale operating conditions. Studies were undertaken to assess the feasibility of this approach to introducing a longwall mining system to the western Canadian coalfields.The longwall method of mining coal is described, world and Canadian usage is reviewed, and the merits of the system in comparison 10 other coal mining methods are discussed.The rationale for a longwall demonstration in western Canada is presented, along with a proposed organization for the design, operation and dissemination of the findings from such a trial. The factors which must be considered in the design of the demonstration, and in the assessment of a potential site are highlighted. It is concluded that a demonstration of this technology is both timely and essential to prepare the way for the western Canadian coal industry of future prospects for coal.IntroductionFor many years CANMET has encouraged research work organized on a cooperative basis. This requires that a working consensus must be negotiated by researchers and operators at the beginning of the project and continuously refined as work proceeds. The result is usually a more relevant selection of research problems, improved direct ion and con duct of experiment al work and often a validation phase in which research concepts are tested in an opera ting environment. All this tends to narrow the gap between obtaining research results and applying them.Even under the best of circumstances cooperative projects require a good deal of coordination and enthusiasm to maintain focus and the pace of work. The working perspective of a research scientist in a government laboratory is substantially different from that of a mine operator at a producing mine, and a common ground must be found. This is difficult to do and cooperative projects typically evolve over several years as experimental results progressively define the potential solutions to mining problems."

Jan 1, 1985

By Masafumi Maeda

Metal recycling and waste treatment have become common issues in various metal industries, notably, the iron and steelmaking industry and the nonferrous industry. The former tends to treat mass wastes such as municipal wastes or plastics. However, volatile compounds are condensed in dusts of their incineration processes and they should also be treated, likely by the nonferrous industry. Those "end-of-life" products contain heavy metals that might be harmful to mankind and should be handled by the non-ferrous industry. Not only revenue derived from regeneration of metals from the secondary materials but also the revenue generated from the treatment charges is a strong attraction for nonferrous industry to process secondary materials. The present study presents some statistical data of the Japanese corporations in the iron and steelmaking industry as well as the nonferrous industry on their revenues generated from processing of secondary materials. Some of the companies are now concentrating their business resources on new areas of the market. Although the quantity of waste or recyclable material is still small at present, the quantity will increase in the near future, and it is anticipated that international collaboration is required to handle the greater variety and the larger quantity of secondary materials.

Jan 1, 2004