Search Documents

By M. Mirnezami, J. A. Finch, M. S. Hashemi A.

The surface of -30µm silica suspension (2% v/v) treated with 100 ppm Mg2+ at pH 11 was fully coated with Mg(OH)2. Under this condition, the silica is strongly positively charged (+30 mV) and the suspension is dispersed. Subsequent addition of Ca2+ promoted aggregation and reduced the surface charge. At this pH calcium is present as Ca2+ and CaOH+, i.e., positively charged ions interacted with the positive surface. Aggregation by a chemical bridging mechanism is proposed. The observation may be relevant to the widespread practice in mineral processing of adding lime to promote aggregation and settling in concentrate thickeners.

Jan 1, 2004

By Adam Jordens

Along with gravity separation and froth flotation, magnetic separation is one of the most common techniques for separating minerals. Minerals are separated by a magnetic force that is dependent on a combination of the applied magnetic field, the magnetic field gradient and the magnetic properties of the minerals themselves. Minerals may be classified as diamagnetic, paramagnetic or ferromagnetic based on the way they interact in a magnetic field. The magnetic susceptibility of a material may be determined by using a vibrating sample magnetometer to determine the magnetic moment of the material in an applied magnetic field and then converting this measured moment into the material?s magnetic susceptibility. In the case of rare earth minerals, magnetic separation is commonly used to remove ferromagnetic iron-bearing gangue minerals and to concentrate paramagnetic valuable minerals such as monazite and xenotime. These magnetic separation steps are frequently preceded by a gravity separation step as many iron oxides and rare earth minerals have specific gravities that are much larger than those of typical gangue minerals. By varying the magnetic field intensity it may be possible to use magnetic separation to selectively separate the paramagnetic and ferromagnetic minerals that report to the concentrate after gravity separation. Test work on a Canadian rare earth ore has shown that a gravity concentration step using a Knelson concentrator was able to selectively concentrate heavy magnetic minerals as evidenced by increased recoveries, relative to the Knelson tailings and fresh feed, after processing through a wet variable intensity magnetic separator. Mass pull to the Knelson concentrate was 4.5 % and the magnetic recovery of this concentrate, at 0.94 T, was approximately 40 % higher than the magnetic recovery from the Knelson tailings (70 % versus 30 %). The products of the wet high intensity magnetic separation were also analysed using a vibrating sample magnetometer to determine the magnetic susceptibilities of the various concentrate and tailings products.

Aug 1, 2013

By Jaeheon Lee

"Biooxidation of gold ores or concentrates could be a very attractive alternative to pressure oxidation (POX) or roasting to liberate the gold grains from various sulfides. Crushed heap bioleaching was successful in US and many operations using tank bioleaching of gold concentrate are currently running around the world. Many parameters need to be considered during the project of sulfidic refractory gold ore process. Capital and operation costs are among the most important ones. Run-of-mine heap biooxidation could be very inexpensive and the smaller the crush size (particle size), the more expensive the capital and operating costs for biooxidation application are expected. The capital cost of biooxidation could be a fraction of the cost for building POX plant or roaster and the operating cost could be 1/3 of POX or roasting depending on the method utilized. A new biooxidation process, Sand Farming, is introduced as an alternative to POX and tank biooxidation process. A relatively coarser particle size (P80 = 650 µm) of the process benefits the low cost of grinding against the conventional grinding size (P80 = 75 µm) for other options. The cost of Sand Farming is less than 40% of that of pressure oxidation with comparable gold recovery from the downstream process. This paper will review the laboratory scale testwork for various biooxidation process of sulfidic refractory gold ores and concentrates and provide the economic evaluation showing the biooxidation could be the most economic method without much sacrificing the overall gold recovery. INTRODUCTIONThe decreased availability and lower grade of raw materials has motivated industries to consider recovering values utilizing low cost process options. The process may treat high grade concentrates or submill grade ores that cannot be processed economically by conventional milling-flotation or leaching. Sulfidic refractory gold ores/concentrates have been economically processed by roasting, pressure oxidation, and biooxidation in stirred tank reactor. The process selection is based on a series of studies including multi-year long ore characterization and metallurgical investigations."

Jan 1, 2016

By P. H. Shipway, D. G. McCartney, H. Saghafifar

The microstructural changes during thermal ageing at 650ºC in the interfacial region of Alloy 625 weld overlay on a 2.25Cr-1Mo steel was evaluated. Optical microscopy, scanning electron microscopy in SE and BSE modes, electron probe microanalysis and hardness mapping were used to characterize as-welded microstructure and its changes during thermal ageing and precipitates of interfacial region. Carbon migration across the interface was recognised as a major issue. A region of 300 µm wide adjacent to the fusion line, which was found harder in the as-welded condition decarburized during thermal exposure. Studies revealed that this region transformed to a soft region containing large ferrite grains and micron-sized carbides. In the weld overlay, a 50 µm wide hard band (over 650 Kgf mm-2) adjacent to the fusion line formed and carbide precipitates were observed along grain boundaries. Carbide precipitation mostly occured in the 150 µm wide region close to fusion line.

Jan 1, 2017

By Nelson C. White

This paper summarizes the present state and future prospects of the potash industry, with special reference to its impact on production in Saskatchewan.

Jan 1, 1968

Red Chris Project Project Status ? Tahltan, Iskut First Nations MOU ? Bankable Feasibility Study ? BC Environmental Assessment Certificate ? CEAA (Federal Environmental) ? EPCM contracts LOI?s ? US$110 million Project Debt Financing(credit approval pending) ? 1st5 years concentrate production sold ? 99,150 m of drilling in 371 holes First Nations Participation Agreement ?Advanced stage negotiations

May 1, 2006

By Siavash Zamiran, Abdolreza Osouli

"One of the most concerns of room and pillar mining system is subsidence of the ground surface due to coal mining particularly in room and pillar mines. Subsidence of ground surface is a result of floor, pillar, or roof failure of the mine. At the same, due to many difficulties associated with surface disposal facilities of coal refuse, some mining companies are trying to use underground space as a disposal storage place. In this study, stability and subsidence analyses of an underground coal mine located in the Illinois Basin are conducted. This room and pillar mine was abandoned and later on was used as a storage place to accommodate the coal fine refuse with slurry backfilling method. The geological stratigrophy and geomechanical properties of the mine floor and roof were collected. Floor and pillar stability analyses were conducted for areas with various extraction ratios. The stability of the mine was evaluated both prior and after slurry backfilling. The floor and pillar stability analyses results of the mine due to moisture exposure after slurry backfilling are discussed. The subsidence potential due to mine failure is also evaluated.INTRODUCTIONA typical lithology of coal seams in the Illinois Basin consists of weak underclay stratum. The immediate weak underclay causes frequent floor instability problems in Illinois underground coal mines. There are two different stages in assessing floor stability of the mines where slurry backfilling is planned. The first stage is during the mining operation when weak underclay layer squeezes under pillar stress and results in punching or bearing capacity failure. The second stage is after slurry backfilling. During this stage, the slurry material soaks non-durable floor layers and causes strength reduction in floor material. Pillar stability conditions should also be taken into account during both the operational period and after the slurry backfilling."

Jan 1, 2015

By E. Ettles

This paper features some of the spectacular new advances in the fields of fluorescent penetrant inspection and magnetic particle concentration. Casting fractures in the various stages -before the repair, during the repair and in the completed repair -using the cold process method will be discussed. This cold method of repair eliminates problems of pre-heating and cooling and the stress factors that are involved in any heat repair.

Jan 1, 1971

By I. M. Masters

Iron removal and control in processes employing pressure leaching technologies developed at Dynatec Corporation are reviewed. Discussions are focused on recent developments in the processing of nickel-copper matte and copper concentrates, and on the Ambatovy laterite project in Madagascar. Iron control and its implications on flowsheet design in the pressure acid leaching (PAL) treatment of laterite ores and in the oxidative pressure leaching of mixed nickel-cobalt sulphide intermediates are also discussed.

Jan 1, 2006

By Ralph L. Rutherford

Introduction During the past twenty-five years we have seen considerable exploration for oil on the plains of southern and east-central Alberta. This exploration has to some extent gone on in cycles, with periodic starts, stops, and occasionally some reversals. Each major attempt is usually supplemented by the application of some new method of exploration and, following each period of exploration, drilling tests are made. Whereas oil-bearing horizons are the ultimate objective of these explorations, the preliminary investigation frequently aims at a discovery of structure based on the long accepted belief that accumulations of oil and gas are to a marked degree structurally controlled. At the inception of this general exploration for oil, it was natural that attention should be directed to areas where there was surface evidence of deformation of the underlying strata, but, as the programme progressed, it was found that these surface manifestations of structure were often deceptive when attempts were made to project them to depth, to involve the deeper strata. Drilling of test wells was the only satisfactory method of obtaining exact information.

Jan 1, 1946

By Aimee Williamson

Bio-mining is a cost-effective, energy efficient and potentially environmentally protective method of exploiting a variety of ore deposits, from high-grade base metal deposits of nickel to lower-grade uranium deposits such as are found in the uraniferous quartz-pebble conglomerate beds of the Quirke Syncline, Elliot Lake, Ontario, using bacterial metabolic processes are used to enhance the solubilization of the metal(s) of interest. The cost effectiveness of bio-mining in Elliot Lake depends on the bacterially-influenced dissolution metals of economic importance, as well as on the ability to suppress microbiological activity following the release to solution of the economically important elements. This poster provides an overview of elemental recovery results and release kinetics for more than 50 elements. The data is obtained using a combination of advanced spectroscopic tools (ICPAES and ICP-MS) to analyze solutions obtained from a series of environmentally controlled biologically mediated uranium ore extraction experiments. The focus will be on rare earth elements, potential environmentally toxic elements, and metals of economic importance. Furthermore, the importance of these findings will be put into an economic and geologic context for the re-development of the mining industry of the Elliot Lake Camp.

Aug 1, 2010

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By Jean-Guy L. Gauthier

"With the Ontario Ministry of the Environment stipulating that the cumulative concentration of copper, lead, zinc and nickel in mine mill effluent must be no greater than 1.0 milligram per litre, it has become necessary for the mining industry of find some form of treatment for the removal of heavy metals from effluent waters.To comply with these guidelines, it became necessary for Mattabi Mines Ltd., which is situated 50 miles Northeast of Ignace in Northwestern Ontario, to develop a compact, cost effective and technically sound treatment process to remove heavy metals from their tailings overflow. A design committee consisting of mine metallurgists, environmental engineers, a Dutch research and development team and the equipment supplier engineering staff was set up to accomplish this.Using some new and innovative wastewater treatment equipment, the guidelines established by the Ontario Ministry of the Environment can now be met. The sludge produced from the precipitated heavy metals is sent directly to the concentrator, thus eliminating the danger of re-dissolution of the metals in a landfill site, while recovering some of the valuable metals that would otherwise be wasted in a sludge landfill."

Jan 1, 1980

By L. Louis

High resolution X-ray computed tomography imaging (with voxel size 48 µm) was conducted on various sandstone samples with different initial degrees of heterogeneity. All samples were imaged intact, and some after having developed localized compaction features in conventional triaxial experiments at high confining pressure, i.e. in the shear enhanced compaction domain (Wong et al., 1997). Our analysis of heterogeneity from X-ray CT data is based on the use of the coefficient of variation d =s /µ (s being the standard deviation and µ the average value). The coefficient of variation was shown by Otani et al. (2005) to be a convenient indicator of material heterogeneity in CT images of experimentally deformed sand piles. The authors reported differences in d before and after their experiments, and interpreted these differences as the effect of grain crushing resulting in more even material distribution within the voxels, hence in lower d values. The same concept was used by Louis et al. (2006) to image contrasts in d values throughout a volume of rock that had developed compaction bands in triaxial laboratory testing, knowing that the bands that had formed could be identified by visual inspection but not on the X-ray CT images. This study resulted in a radically enhanced image of the discrete compacted zones within the CT-scan series, whereby more deformed areas showed relatively low values of coefficient of variation due to grain crushing and pore collapse, as compared to nominally undeformed areas.

May 1, 2009

By John H. Low

Introduction Despite the fact that the .association of magnetite with chrysotile asbestos in the parent producing area of the world, the Thetford Mines - Black Lake area, has been recognized since the ores of that region were first known, magnetic methods were not extensively employed in exploration for asbestos until about the beginning of 1949. Since then, large areas of Ontario, Quebec, and the eastern United States have been prospected both by aeromagnetic and conventional ground magnetic methods. Prior to 1949, a limited amount of magnetic work had been done, notably that of A.H. Miller (1, pp. 184-186), which was carried out in conjunction with the geological survey of the Thetford area by H. C. Cooke (2) in the years of 1930 to 1932. At that time, Miller pointed out that the occurrence of asbestos is associated with very large magnetic 'anomalies' and that, within the Pennington dyke, an area of asbestos- bearing peridotite could be distinguished, by the anomalies, from adjacent areas of non-asbestos ?-bearing peridotite. Since he .also observed large anomalies in what were believed to be ?barren areas, Miller concluded, however, that the magnetometer could hardly be of much or any value in the direct location of asbestos War .and post-war demands on known reserves of asbestos ore, however, stimulated the search for new deposits, and an economical and rapid method of directing speculative drilling was most desirable.

Jan 1, 1951

By M. Mahfoud

The effect of grain refinement on the tensile and fatigue crack propagation behavior of sand cast magnesium alloy AM60B has been investigated in the present study, C2Cl6 in the amount of 0,3% was used to grain refine the melt, The fracture toughness tests were conducted in laboratory air at room temperature (25°C) using a sine-wave cyclic frequency of 20Hz and a load ratio of R = 0,1, The response in the Paris's regime and the critical stress range were determined, Preliminary findings have shown that C2Cl6 has a significant effect on both the tensile properties and fatigue crack propagation of the alloy tested, Grain refinement increased both the yield and ultimate tensile strength by more than 46%, and decreased the crack growth rate from 2,7 to 1,4 MPa Vm , However, the grain size seems to have a smaller effect on threshold stress intensity factor range. The fracture surfaces of specimens were examined optically and under the scanning electron microscope (SEM) to determine the relationship between grain size and fatigue properties.

Jan 1, 2005

By C. Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in the flotation circuit were calibrated using a dynamic grinding/flotation simulator. Predicted values are multiplied by g/t ratios to calibrate reagent flow. The transfer functions are currently integrated into the distributed control system at Les Mines Selbaie.INTRODUCTIONThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970's there have been numerous publications dealing with practical applications of flotation process control. A review of that literature shows that basic feedback and feedforward controls are the two preferred strategies for flotation processes. Some advanced control schemes started to emerge (e.g. Zaragoza and Herbst, 1988). Feedforward and feedback aim at reducing the effect of the following flotation process disturbances (e.g. McKee, 1991):0 Changes in throughput;0 Changes in feed grade;0 Changes in particle floatability (size, liberation, surface oxidation ... );0 Deliberate changes of set-point;Feedforward strategy acts on manipulated variables, mainly reagent addition, to attenuate the effect of disturbances such as changes of feed rate and grade. The feedforward strategy is driven by measurements of disturbances. Feedback control acts to compensate unmeasured disturbances, such as ore floatability, and to bring process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by set-point error, caused by either a deliberate change of set-point or unaccounted disturbances.This paper proposes a way to improve feedforward control schemes by addition of a simple model of solids transportation. The feedforward strategy considered in this paper is of ratio type, i.e. the manipulated variable is changed according to a predefined ratio between this variable and the measured disturbances. A typical example is the ratioed reagent addition to mass flow of ore."

Jan 1, 1993

By M-A. Thibault, C. Gauthierand, J-P. Gagné, J-Y. Carrier, P. Rochette, G. Dufour

"Anodes consumed in the electrolytic process for the production of primary aluminium are considered consumables. They need to be replaced at regular intervals of approximately one month. The so-called anode butts which are removed from the cells contain the metal supports (rods), cast iron thimbles, crust and residual carbon material. Cleaning is required to remove the waste material before the rods are fitted with new anodes. An inspection is required to ascertain if repairs to the rods are necessary. Presently, this inspection is carried out visually. ST AS, in 2004 in collaboration with Alcoa Deschambault, initiated a project to develop an automated inspection system. The objectives were to find a technical solution to perform these functions with a very simple system. Such a system was designed around ""artificial vision"". The inspection system developed uses only one fixed camera and does not require a separate step in the process for the anode rod assembly to perform the inspection. This paper presents the initial steps of the work performed to develop the equipment and software as well as a summary of the results obtained."

Jan 1, 2006

By P. Erskine

"Hyperaccumulator plants can be utilized as ‘metal crops’ in agromining operations. This emerging technology produces ‘bio-ore’ by growing ‘metal crops’ on sub-economic ore materials, such as natural ultramafic soils. In a typical application plant material is periodically harvested, followed by air-drying and incineration to produce the bio-ore intermediate. The bio-ore is of very high grade (>15 wt. % nickel), and of high purity, and may be processed into a number of different products (including nickel metal, nickelbased catalysts and pure nickel salts). Current research efforts from our team focus on Mediterranean climate field trials (Albania, Spain) and tropical climate field trials (Malaysia, Indonesia). Field-scale demonstrations are required to provide evidence of real-life performance and of economic viability. If the trials are successful, agromining may in the near future support local livelihoods with income opportunities as an alternative type of agriculture: to farm nickel.INTRODUCTION AND BACKGROUNDHyperaccumulators, plants with the exceptional ability to uptake and concentrate trace elements in their shoots, can be utilized as ‘metal crops’ in agromining operations (Van der Ent et al., 2013a; Chaney et al., 1998; 2007; Baker et al., 2010). Agromining produces ‘bio-ore’ from harvested ‘metal crops’ grown on unconventional resources such as natural ultramafic soils (Van der Ent et al., 2015a). The bio-ore is a high purity and very high-grade (>15 wt. % nickel) product intermediate that may be turned into a range of different nickel products (nickel metal, nickel-based catalysts and pure nickel salts). The potential for agromining is greatest in tropical regions (Asia-Pacific Region: Indonesia, Malaysia, Philippines, Papua New Guinea and New Caledonia) where very large expanses of ultramafic soils exist (Van der Ent et al., 2013b). Agromine operations may replace existing marginal agriculture on poor ultramafic soils, for example oil palm plantations that require high fertilizer inputs to be profitable, or take place under a cocropping regime. The ability of ‘metal crops’ to achieve high nickel concentrations in biomass (and hence in harvested bio-ore) from soils with just <0.5 wt. % nickel, makes it possible to access non-conventional resources, not accessible by traditional mining techniques. For example, agromining could be implemented both on the large ‘halo’ around the mine leases, and as part of the progressive rehabilitation process after conventional resource extraction. As with all methods for resource extraction, agromining will be finite due to the diminishing concentrations of nickel in the zone accessible by plant roots (Chaney et al., 2014). Nevertheless, considering soil materials with 0.2 wt. % nickel and ‘metal crops’ with a yield of 100 kg nickel ha-1 the agromining venture may be sustainable for decades (Van der Ent et al., 2015a)."

Jan 1, 2016

By Kevin S. Borthwick

The subject of this paper is a facility wide Distributed Control System (DCS) upgrade being completed at a large copper and molybdenum mine. This paper will discuss the innovative hardware and software technologies employed in the new control system. This paper will also describe the planning process, migration path and simulation techniques used to ensure the success of such a large and complex DCS upgrade.

May 1, 2008