Search Documents

By D. Nikols, G. Caraghiaur, P. C. Roxburgh

"IntroductionThe Highvale Mine is located 70 km west of Edmonton , Alberta on the south side of Lake Wabamun. It has been developed by TransAlta Utilities Corporation as a captive mine to supply fuel to two genera ting power plant s. The mine is owned by TransAlta and operated under contract by Manalta Coal. Within the mine permit area, TransAlta own s the right to mine 80% of the recoverable surface mineable coal.The planning process starts with the annually produced 25-year energy forecast which is provided by the Electric Utility Planning Council (EUPC). A 1983 forecast predicts an average annual increase in energy requirements of 4% over the next 25 years. Put another way, the requirement will double before the end of the century. A lar ge part of the base load generation of the Province of Alberta is provided by th e plants fueled from Highvale Mine. The Highvale Mine is therefore expected to maintain a high output over a long period of time.Mine PlanningMine planning is an ongoing, interative process that draws from many sources. All levels of planning draw from the same sources but du e to the different processes and objectives of each planning class, the degree of influence may differ. The planner becomes then a coordinator bringing together data and excerpts from several disciplines in groups. Generally, there are four classes of mining plan s; these are all used at the Highvale Mine (Table I)."

Jan 1, 1986

By Y. Prevost, D. Verhelst

"A computer-assisted process control system for the Noranda Process Reactor Wa5 installed at the Home smelter in 1991. Operating as an advisory tool for the furnace operators, and using a flexible oxygen balance as the basic building block of the computer program, the new control system has helped to reduce the variability in the grade of the matte produced by 50% . The smelter is currently operating at a 72% copper matte, with a standard deviation of between 1.0 and 1.3, while treating a wide range of concentrates, secondary materials and scrap. Enhanced process control has allowed for longer reactor campaigns, and improved stability of the converting operation.This paper reviews the feed classification and blending practice used at the smelter, outlines the strategy of the new computer control system, and summarizes the benefits realized since the implementation of the system in early 1990.IntroductionUntil 1989 the Noranda Home smelter operated as a multi furnace smelter, at one time having three hot-charge reverberatory furnaces, and finally operating with one wet-charge reverberatory furnace and one Noranda Process Reactor. In 1989 the final reverberatory furnace was closed and the Reactor became the sole smelting vessel, treating around 750 000 tonnes of concentrate, secondary materials, and scrap per year. At the time of the start-up of theNoranda Reactor in 1973, the vessel was capable of treating 750tonnes per day of a heterogeneous mixture of copper concentrates, fluxes and secondary materials to produce copper in one operation. Through process improvements, and the introduction of additional oxygen in 1982(pannell and Mackey, 1988), the daily tonnage increased to 1800 tonnes by 1988. The operation had also been changed to produce a high-grade matte instead of copper. Figure1 illustrates the main features of the reactor, a cylindrical vessel which is charged at one end and tapped at the other. The matteis subsequently processed through Peirce-Smith converters and anode furnaces before being cast into copper anodes. Figure 2 outlines the progressive increase in the furnace smelting capacity. Over this period the percentage of secondary materials, and scrap feeds also increased to approximately 110 000 tonnes per year, or 15% of the total new feed input (Bedard et al., 1991). Now operating wholly as a custom feed operation, the Home smelter can treat over 2200tonnes per day of new metal-bearing material."

Jan 1, 1993

By A. Alfantazi, E. Asselin

"The corrosion of commercially pure titanium (CP-Ti) was studied from room temperature up to medium temperature (~160°C) under conditions relevant to medium temperature chalcopyrite leaching processes. The corrosion rates were measured by immersion and electrochemical tests in sulfuric acid. The influences of chloride, cupric and ferric ions on the corrosion rate and behavior were also investigated. Corrosion of the CP-Ti did not account for the total current density measured by linear polarization tests. The corrosion rates of CP-Ti under medium temperature leaching conditions were surprisingly high. The corrosion rate measured in ferric containing solution at 160°C was approximately 20 mm/yr.INTRODUCTIONTitanium exhibits excellent corrosion resistance in many aggressive environments because of the formation of a very chemically stable, highly adherent, and protective oxide film on its surface (Mitsuo et al., 2002). Because titanium is the only metal available at a reasonable cost that resists the high temperature corrosive slurries in many leaching processes, it is often chosen as autoclave liner material where it is subjected to severe conditions of acidity, temperature and pressure (Grauman and Say, 2000).A number of distinctly different hydrometallurgical processes for the pressure leaching of chalcopyrite have been developed and patented by various companies and they can be classified into low, medium and high temperature regimes (McDonald and Muir, 2007). For example, chalcopyrite concentrate may be processed at medium temperatures (115-175°C) and pressures of 800-2200 kPa (Dreisinger, D., 2006; Sahu and Asselin, 2011). The lixiviant may contain 20 to 55 g/L sulfuric acid, 8 to 12 g/L chloride ions, 10-25 g/L Cu2+ (Jones, 1995, 1997, 1999), and less than 1 g/L Fe3+ (Defreyne et al., 2005). The amount of these additions is determined by the grade of the ores and details are shown in Table 1."

Jan 1, 2012

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By M. Leahy

"Very little is known about the large scale fluid dynamics and associated distribution of copper in an operating electrowinning cell, yet they will have a major influence on mass transfer and plating quality. The CFD model in this work is used to simulate an entire EW cell with 60 cathodes and 61 anodes, or 121 anode–cathode pairs, elucidating for the first time the three-dimensional (3D) flow and copper distribution in an industrial cell. Two methods for the distribution of electrolyte are modelled:1. Downcomer method: electrolyte is fed by a downcomer at one end of the cell, overflowing at the opposite end.2. Manifold method: a horizontal manifold pipe runs the whole length of the cell and feeds electrolyte via small holes in the top of the manifold pipe.The recirculation that develops within each anode-cathode pair, driven by oxygen bubble generation on the anode, is similar to that seen previously in two-dimensional models of single anode–cathode gaps. However a more complex 3D flow recirculation is established, which involves flow of electrolyte down the side gaps (being a path of low resistance for return flow) as well as the usual return flow down the cathode side of each pair gap. The bubble-driven flow is not influenced by the mode of electrolyte distribution.The electrolyte flow due to the manifold and downcomer is somewhat secondary to the bubble driven flow. In the case of the downcomer distribution mode, the high injection velocity causes a very turbulent flow in the first 1–2 m down the cell from the downcomer, with several large vortices developing. This may lead to some sludge particles being entrained into the bulk of the cell.In the manifold pipe case, the jet from each hole is dissipated very quickly, within the first 10–20 cm. The jets are directed into the downward flowing zone of the bubble-driven recirculation, which leads to unstable and periodic behaviour on a large spatial scale.In both the manifold and downcomer cases, there is a marked two-zone vertical stratification in copper concentration."

Jan 1, 2016

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By T. H. Patching, M. W. Mikhail

"Data from a standardized procedure for measuring methane desorption rates from samples of Western Canadian coals gave a good correlation (0.994) with the percentage of fines (-0.6 mm) found in the corresponding run-of-mine coal. The correlation was independent of the mining method and the top size of the samples. It is suggested that both methane desorption rate and the production of fine coal sizes are functions of the fissuration of the coal being mined.This relationship, in conjunction with established data of degradation by unit process equipment, may be useful in predicting the amount of fines that will be produced from new seams of coal and by planned new washeries. It also could be a valuable guide in modifying existing washery processes to minimize production of fines."

Jan 1, 1980

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By R. Kaibyshev, I. Zuiko

"The effect of thermomechanical processing (TMP) including cold working by tension or rolling before aging on mechanical properties and a dispersion of secondary phase particles of an AA2519 alloy (Al–5.64Cu–0.33Mn–0.23Mg–0.15Zr–0.11Ti–0.09V–0.08Fe–0.01Si (wt. %)) was examined. It was shown that the use of tension to impart pre-strain =10% in the alloy provides the best combination of properties in peak aging condition of the material. The AA2519T87 alloy processed by tension exhibits the yield stress, ultimate tensile strength and elongation to failure of 425.4±2.4, 475±2.4, 12.1±0.4, respectively. The one pass rolling leads to -5% decreases in yield stress and –20% decreases in ductility. Dislocations serve as heterogeneous nucleation sites for ?'-phase precipitation. The positive effect of tension is attributed to the formation of more homogeneous dislocation structure, uniform distribution of ?'-phase particles with higher aspect ratio. Precipitation of the O–phase plates on {111}a habit plane was detected. In addition it was shown that the low angle boundaries are heterogeneous nucleation sites for ?' and O particles.INTRODUCTION Precipitation-hardened alloys are a commercially important group of the materials because their mechanical properties can be modified by treating and changing the microstructure. Age-hardenable aluminum alloys belonging to the Al–Cu–Mg system are widely used due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance attributed to the highly efficient strengthening by the ?'-phase (Palmer, StJohn, Nie, & Qian, 2017). An AA2519 alloy exhibiting superior mechanical properties among high-strength Al–Cu alloys (2XXX-serie) due to minor Mg additives. It is known that, in alloys with high Cu/Mg ratio (=5.6) the classic precipitation sequence (Palmer et al., 2017; Wang & Starink, 2005; Wang et al., 2010) of supersaturated solid solution (SSSS) decomposition occurs: SSSS ? GP zones (Al3Cu) ? ?? (Al3Cu) ? ?' (Al2Cu) ? ? (Al2Cu) (1)"

Jan 1, 2018

By Shengwu Song, Xuemin Feng

Jinping I hydropower station is located in Sichuan Province in Southwest China. It is built on the Yalong River as a controlling cascade hydropower station in the middle and lower reaches, with power generation as its major function. Jinping I arch dam concerns many engineering issues and has attracted worldwide attentions due to its huge scale and unique settings. It is one of the most challenging projects in China with its 305 meters high arch dam and complex geological conditions for construction, including large-scale tectonic faults, intensively unloaded rock masses and geological asymmetry in its foundation. At present, the concrete arch dam construction has been completed and preliminarily impounded, most of the foundation treatments have been implemented, and four of six generator units had been put into operation in July 2014. In this paper, the analytical methods, design concepts, treatment measures and technical features of strengthening the geological defects in the dam foundation will be presented. Upon geological investigation into the dam foundation, a few large-scale weak discontinuities are observed. The rock masses in the left dam foundation are intensively unloaded, approximately to the horizontal depth of 150–300 m. These serious geological defects lead to a geological asymmetry on the left and right banks, and thus some major difficulties of dam construction are encountered. The influences of geological defects on the dam construction and safety are analyzed comprehensively, followed by the concepts and methods of treatment design. Based on this, the treatment methods of the weak rock masses and discontinuities are carefully determined by numerical analysis and scheme optimization, including the concrete cushion, concrete replacement grids, drainage system, anti-seepage curtains and consolidation grouting, which work together to enhance the strength and integrity of the dam foundation. Evaluations and calibrations through geo-mechanical model tests in combination with field monitoring results in early impoundment period show that the arch dam and its foundation are generally stable and function normally, which suggests that the research methods and treatment design schemes are reasonable and effective. The proposed treatment methods and concepts in the context are helpful for similar complex rock projects.

Jan 1, 2015

By D. Houghton

"I am very pleased to be a member on this panel today because abrasion and wear in mills has been part of my life over the past forty years. My presentation will deal with the role Ni-Hard has played in combating wear and abrasion in mills. Before Ni-Hard came along, unalloyed white iron was used in ball mills and one of the most popular types of white iron liners was the pocket liner. Slide #1 illustrates the design of the pocket liner used at Dome Mines in their 5' x 22' pebble mills. The pockets filled with grinding media and it was on this that the wear took place. The concept is not unlike the new magnetic liner which utilizes the ore and grinding media to form the wearing surface. In this slide please note the tapered pocket type of cored bolt holes. If cored bolt holes do not fill with grinding media there could be excessive grooving or wear at that area. Therefore all cored bolt holes should be tapered in this manner.Before Inco patented the name Ni-Hard several foundries were making the alloy iron under different brand names such as Diamond Alloy, Mitchelloy and Specialloy. In the early days some of the Ni-Hard was poor quality. Inco provided foundries with technical knowhow and provided assistance to licence them to sell under the name of Ni-Hard. This was in the late 1920's. The material we are discussing is Ni-Hard type I with the following analysis (slide #2). It is a martensitic white iron with BHN of 550 - 600 and is a relatively easy alloy to produce in either a cupola or electric furnace. The annual average production of Ni-Hard in North America is 90,000 tons with mill liners making up 25,000 tons and grinding media 30,000 tons, according to Warren Spear of Inco."

Jan 1, 1983

By Brian Hart, Stamen S. Dimov

"The naturally occurring carbonaceous material (CM) in gold bearing ores often exhibits strong-preg-robbing properties. It can adversely affect the process of gold recovery during the cyanidation due to its ability to adsorb, or preg-rob gold from the cyanide leach solution.Treatments of carbonaceous ores with chemical surfactants as blinding agents to limit preg-robbing have shown promising results but at the same time have demonstrated that, if not properly used, could have a strong detrimental effect on the gold recovery process. High dosages of surfactants used as passivating agents for carbonaceous matter could lead to unwanted partial passivation of the activated carbon added during the CIL process and severely impact the gold recovery. Optimal dosage for various surfactants would strongly depend on the ore mineralogy and the parameters of the pulp (temperature, pH, surface area and maturity of the carbonaceous material, etc).This paper describes an experimental study on the effectiveness of various commercially available blinding agents used to minimize the preg-robbing capacity of naturally occurring carbonaceous matter. The scope of the study was to: i) establish the optimum addition of blanking agent (surfactant) to minimize the preg-robbing capacity of the CM in the ore, and ii) establish maximum threshold amounts of blanking agents to be used before it negatively impacts the preg-robbing capacity of the activated carbon used in the CIL process. The study procedure involves standardized doping tests to evaluate the maximum preg-robbing capacity of treated CM, coupled with surface analysis with ToF-SIMS to monitor the presence and the degree of loading of these chemical surfactants on both the naturally occurring CM and the added activated carbon.INTRODUCTIONNaturally occurring carbonaceous material (CM) in gold bearing ores often exhibits strong-preg-robbing properties. Thus, it can adversely affect the process of gold recovery during cyanidation due to its ability to adsorb, or preg-rob gold from the cyanide leach solution. The preg-robbing properties of this naturally occurring carbonaceous matter can vary widely between ores, and within a single ore body (Dunne et al.,2013;Helm et al.,2009;Miller et al.,2005). The degree of preg-robbing related to the CM within an ore is defined by several parameters: total organic carbon (TOC) content, surface area, maturity (i.e., crystallinity) of the CM and the presence of various functional groups on the surface of the CM. Preg-robbing gold ores continue to be a significant challenge because of the lack of a single or universal solutions."

Jan 1, 2016

By Alexander Burns, David Dreisinger

The kinetics of the oxidation of uranium(IV) by oxygen gas in aqueous systems is dependent on acid concentration, oxygen partial pressure, and temperature. In order to better understand the relationship between these variables and the speed of oxidation, a series of experiments have been conducted where each parameter has been varied in turn. Data were collected continuously using UVVis spectroscopy, allowing for a detailed examination of the reaction rate over the course of each experiment. The data fit an overall apparent rate law that is 1.5order in uranium(IV), -2order in H+, first order in oxygen, and unaffected by uranium(VI). This relationship does not appear to hold for solutions with <0.2 mol/L initial acid, where a different kinetic mechanism appears to be dominant.

Jan 1, 2014

By William H. Pomroy, Kenneth E. Hjelmstad

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. A fire emergency plan includes a means of warning miners of the existence of a fire, and the need to evacuate or retreat to a place of refuge. The warning alarm must be fast and must reach all miners, regardless of their location or work activity. Means of fire warning are varied, and include such methods as stench, flashing lights, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. Stench can be slow and seldom achieves total mine coverage, especially in high-back room-and-pillar mines with low ventilation velocity. Telephones are effective only where personnel are close enough to hear the phone ring. A novel fire warning alarm system has been developed by the U.S. Bureau of Mines which enables instantaneous warning of all underground personnel. The warning alarm is sent by an electromagnetic signal which penetrates through mine rock from a transmitter to small person-wearable receivers. Each miner&apos;s cap lamp battery could be equipped with a small receiver and when a fire or other emergency occurs the miner could be alerted to the danger by a blinking of the cap lamp. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This paper describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, design of the prototype transmitter and receiver, test results, and status of commercial development of systems utilizing this technology.

Jan 1, 1994

By Y. Jin, H. You, H. Pang, B. Lin

Successful application of steam assisted gravity drainage (SAGD) on the recovery of land facies ultra-heavy oil in Xinjiang oilfield depends largely on shortening the preheating period with the aid of the micro-fracturing technology, which is conducted through controlled water injection to a pair of horizontal wells to create homogenously distributed microcracks in the zone between the two wells. The numerical simulation of this mechanical process is yet to be investigated. Up to date, there has been research work on rock mechanics during the SAGD production period of marine deposited ultra-heavy oilsands, but the counterpart research on land facies ultra-heavy oilsands of Xinjiang oilfield is left undone. In this regard, this study is attempted to perform numerical simulation of the fracturing process on land facies unconsolidated oilsands. With this objective, the study first investigates geological and physical identification of the field collected cores, then carries out mechanical analysis on laboratory triaixal test results, based on which numerical simulation of the fractured zone is performed. The simulation is applied through a finite element platform adopting extended Drucker-Prager constitutive model, with the parameters determined by experimental work. It is verified that hydraulic fracturing of unconsolidated oilsands generates a microcrack feature in terms of a dilative zone instead of linear apertures. The extent to which the fractured zone propagates is visually demonstrated based on the magnitude distribution of equivalent plastic strain or volumetric dilation. Evaluation of the connection of injection and production wells can possibly be determined by the expansion of the saturated region around each well. Finally, the implications on the efficiency of hydraulic fracturing in stimulation of the pay zone are investigated.

Jan 1, 2015

By Gilles Bonin

Structures and serpentinization patterns in the Thetford Mines peridotites are important characteristics indicating the necessary geological conditions which led to the development of chrysotile orebodies in Early Ordovician limes. These structures and serpentinization patterns are reviewed in this paper using the geology of LAB Chrysotile orebodies as a model. Structural aspects include parallel and transverse faults, parallel and transverse granite slabs, and orebodies, some of which trend clearly north-westward parallel to the accretionarymovement. Serpentinization patterns in the peridotite belt, particularly in the harzburgite, include primary pervasive mass serpentinization and secondary complete serpentinization. Listwaenites layers appeared along some faults and along some granite slabs as a result of hydrothermal alteration of the serpentine, following the emplacement of the devonian plutons to the south. These plutons as we/1 as other important lineaments, align with the structural pattern of Thetford Mines ophiolites. It is believed that these plutons are part of a heavy magma tic corridor resembling the Pilote-Mont-Louis corridor in the Gaspe (Doyon and Berger, 1997), and the Buchans' structure in Newfoundland (Hutchinson, 1984), both intersecting the Brompton-Baie Verte line.

Jan 1, 2001

By Deborah McCombe

"and Bill Roscoe, Consulting Geologist and Principal with Scott Wilson Roscoe Postle AssociatesMineral property valuations are carried out for a variety of reasons, such as mergers and acquisitions, non-arm’s length transactions, initial public offerings of stocks, support of audited financial statements, fairness opinions, determination of vendor considerations, litigation, expropriation, income tax matters and insurance claims.The CIMVal Committee was formed in 1999 to review and advise on approaches to the valuation of mineral properties. CIMVal is a special committee of CIM formed on the recommendation of the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission.After solicitation of views and consultation with various interested parties, the CIMVal Draft Standards and Guidelines for Valuation of Mineral Properties were released for comment in February 2002 and were finalized in February 2003. CIMVal’s objective was for the standards to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges. To that end, the standards contain many of the definitions and concepts of National Instrument 43-101, Standards of Disclosure for Mineral Projects, which came into force in February 2001.The intent of the CIMVal Standards and Guidelines is that mineral property valuations be carried out by appropriately qualified individuals and that all relevant information be fully disclosed. It consists of two parts: standards, which are mandatory in the valuation of mineral properties, and guidelines, which elaborate on the standards and provide guidance and recommendations for the valuation process and for reporting."

Jan 1, 2003

By A. C. Bonnier

"INTRODUCTIONI have been asked to make available our method of determining the ""Live Inventory"" within a gravity type thickener. The ""Live Inventory"" being that tonnage compatible with the optimum underflow density that satisfies the process requirements.One prerequisite of the calculations is the proper determination of the final pumpable underflow density. A further requirement is that, prior to shutdown, the thickener has been operated properly, particularly that it has not been operated for storage capacity.Until recently I had few chances to check the method. However, I was most fortunate to have had a recent opportunity covering several months on a 300 ft diameter thickener at a plant in the U.S.A., wherein the method was tested and verified many times. The method proved accurate in that our calculated tonnage checked with the actual dried physical inventory of the drying facility.At the precise moment that the feed to the thickener was shut down, a per cent solid determination was made at the critical place and the tonnage in ""Live Inventory"" determined. Let us say that at the moment the thickener U&apos; Flow solids was 20%. The thickener then was allowed to cperate until the U&apos; Flow solids dropped below 20%, at which time the thickener was deemed to be relieved. Anything much less than 20% was not suitable to the subsequent centrifuge operation.Most large metallurgical thickeners have a configuration of three slopes at the thickener ""bed"". These slopes are dictated by the raking blades and are shown on the manufacturers&apos; erection drawings. The first slope is from the outer periphery and generally takes up a distance of about 60% of the radius, the second slope generally taking up the remaining 40%. Within this 40% area, there is usually another slope taken up by the cone on ""B"" type thickeners or an actual steeper inner slope on ""C"" type thickeners."

Jan 1, 1989