Search Documents

By Mel Owen, Bob Tipman

"A number of studies have identified the presence of heavy minerals in the Athabasca oil sands. A 1996 Mineral Development Agreement study into the recovery of Co-Products identified low operating costs, a simple flowsheet and access to market as key drivers in advancing interest in a viable project.Commercial bitumen extraction processes recover 50% of the titanium heavy minerals and 85% of the zircon into froth containing 1 % of the feed solids. Froth treatment tailings grade is 11.5% Ti02 and 3.6% Zr02.Processing this high grade feed in a combination of flotation, roasting, screening, gravity concentration and magnetic separation, results in concentrates of rutile, leucoxene, ilmenite, zircon and rare earths of marketable quality.A combination of high grade feed and a simple process lead to operating costs among the lowest in the industry. Low cost heavy minerals and low energy costs indicate an intriguing potential for low cost pigment production in Alberta. The production of heavy minerals from oil sands remains one of the largest untapped resources in the Province of Alberta1.0 IntroductionThis paper describes the results of an investigation into the recovery of heavy minerals from tailings produced by the major oil sands plants. The study was carried out under a Canada-Alberta Mineral Development Agreement (Alberta Chamber of Resources 1996). The MDA Co-Products Study examined the potential for the economic recovery of heavy minerals from oil sands tailings."

Jan 1, 1998

By Alan Bateman

Introduction A few years ago the name Katanga recalled, to those interested in copper, a far-off country in central Africa where deposits of huge size were beginning to pour a stream of copper into the world's markets. But no one heard of the adjacent part of northern Rhodesia as a potential copper region. It was then a bush-covered wilderness, with a few lonely, widely-spaced villages, and here and there a copper prospect that created but little outside attention. There was also one struggling mine whose development created pessimism. The low-grade carbonate outcrops of Rhodesia did not compare favourably with the rich carbonate ores of Katanga. And, since Katanga was mining only oxidized ores, it was then thought that this adjacent region likewise would contain only oxidized ores. The one mine that had been started, Bwana M'Kubwa, was working on low-grade carbonate ore at a loss. The outlook was not promising. But, a little over three years ago, the aspect changed. The vision of one far-sighted engineer embraced the possibility that here copper sulphides might underlie those low-grade carbonate croppings. His courageous associates furnished the capital; drilling commenced, and the great Roan Antelope mine rapidly emerged. In quick succession, the N'Kana, Mufulira, N'Changa, N'Changa Extension, and Chambishi mines were heard from. Prospecting and development are now proceeding apace, towns are being hewn out of the virgin bush, plants are being reared, and ramifying branch railways are being pushed out from the single line of steel that now connects Rhodesia with the coasts to the south. A great new copper-mining centre is in the making, about which the world will hear much in the future. As with most new mining camps, rumors abound regarding its ore possibilities; some are correct, some are erroneous, and reliable information unfortunately is all too scanty.

Jan 1, 1930

By Mark Weidenbach

OZ Minerals owns and operates the Prominent Hill copper-gold concentrator in South Australia, built in 2008 and commissioned in early 2009. The concentrator operates via semi autogenous grinding in a thirty four foot ThyssenKrupp Polysius mill followed by a twenty four foot Polysius ball mill in closed circuit with hydro cyclones, designed for an ore throughput of eight million tonnes per annum. The main aspects of designing the circuit are discussed along with the issues faced in the early stages of operation. A review of the optimization strategy applied to the milling circuit such as cyclone optimization, advanced process control strategy implementation and reline management to improve availability is then discussed highlighting areas of significant process improvement that have seen the plant exceed nameplate throughputs above nine million tonnes per annum.

Jan 1, 2012

By J. G. Bensley, K. S. Detheridge

"Many plants use computers for process control and most have computerized Management Information Systems but few have been able to have these systems interact with one another. Developing this system interaction is not a one-step process but requires careful planning and implementation. This paper describes two projects that were implemented to provide the bridge between the process control and management information systems of Cominco Limited. Both projects include the replacement of essentially process control systems installed in the late 1960s. These original systems provided an enhanced level of control in the form of Direct Digital Control (via computer/manual analogue control stations) and a management reporting capability of process data. The experience gained from the use of these systems over a period of fifteen years formed a basis for the evaluation and planning for the new systems. The new systems were commissioned in 1985 and 1986 and operating and further developments leading to a totally integrated process information and control system are underway. INTRODUCTIONThe concept of hierarchical control involves a control structure consisting of a number of defined levels. Each level performs a defined function with information consolidated and combined as it moves up through the hierarchical structure. The commonly accepted structure of a hierarchical control system echoes the structure of the plant which is being controlled. Referring to Figure 1:Level 0 - Sensors and ActuatorsSensors and actuators, such as thermocouples and flow control valves, interface directly to the process and are generally connected directly to the controllers or multiplexers at Level I.Level 1 - Regulatory ControlThis level provides basic PID control (proportional/integral/ derivative) typically using microprocessor based controllers and programmable controllers for digital control of motors and machines. Systems at this levelare usually segregated by plant unit, e.g, crushing, flotation, drying. Control is concentrated on achieving optimum conditions for a particular feed rate."

Jan 1, 1989

By W. Keith Buck

This paper defines the discipline of mineral economics. By example, it describes the application of the tools of economic analysis to mineral problems - to problems in the areas of: mineral resource analysis and forecasting, mineral industry activity from exploration to distribution and marketing, mineral commodity analysis, and mineral policy analysis and policy formulation - all in a regional, national or international context.

Jan 1, 1972

By I. E. Puddington, F. W. Meadus

The beneficiation of barite in mill tailings using an agglomeration technique has been demonstrated. Barite was selectively absorbed from a conditioned aqueous slurry into a collector oil by mechanically mixing slurry and oil. The resulting oil-bonded barite-containing agglomerate was washed, to remove gangue material, and further mechanically contacted with dilute H2SO4 This treatment resulted in the transfer of barite into the aqueous phase. Grades as high as '97% BaSO4, with recoveries of 80%, have been obtained using this technique.

Jan 1, 1973

By R. Salimi

Tricalcium aluminate hexahydrate (TCA) is used as filter-aid for security filtration in the Bayer alumina process. TCA is typically produced on-site by mixing Bayer liquor with slaked lime. Specific properties are required from the TCA to ensure adequate filter throughput, lifetime and importantly effective reduction of solid/colloidal impurities from the solution. The effect of reaction time on morphology and particle size distribution of tricalcium aluminate was studied for a batch experiment at simulated process conditions. It was found that reaction time plays a critical role on the morphology, crystal structure (diameter and crystallinity) and particle size distribution. In the early stages of the reaction, nucleation dominates the crystallization process followed by growth dominated by agglomeration up to a mean particle size of 10 µm. The particle morphology shifted from an irregular shape to more spherical throughout the course of the reaction.

Jan 1, 2014

By S. Parent, J. -F. Lepage, S. Glover

"Goldcorp – Eleonore’s 7 000 tonnes per day gold mill was started up in October 2014 and achieved commercial production in April 2015. During the first year, operation has faced challenges from grinding, flotation, sulfide cyanidation and tailing filtration to achieve targeted throughput, availability and recovery.The optimization of non-sulfide tails filter cloth lifetime and filter press availability had the most significant impact on ramp-up of both mill throughput and availability. A change in steel ball addition size to the grinding circuit was made to meet the targeted p80 of 65 µm. Various optimization efforts were conducted on the flotation circuit, intended to recover all sulfide-bearing minerals. The goal is to attain the environmental target of 0.12% sulfur in flotation tails (to eliminate acid mine drainage or AMD), while an average of 0.31% sulfur was obtained over the first months of 2015. Collectors, frothers, activators and hydrodynamic parameters were tested to improve the circuit desulfurization efficiency. High sulfide reactivity in pre-oxidation and cyanidation severely impacted dissolved oxygen levels and cyanide consumption. Studies were undertaken to understand the effects of mineralogy, grind size and leach conditions on gold dissolution kinetics and cyanide consumption. Efforts were focused on pre-oxidation to restore dissolved oxygen levels as well as optimizing both lead nitrate addition and pre-oxidation time.INTRODUCTIONGoldcorp Eleonore’s mill commissioning started in September 2014. It was considered to operate the mill at 3 500 tpd during design, as the mine was planning to operate at this throughput for the first year. However, with the stockpile of ore and a higher throughput from the mine, the mill was able to run at higher tonnage than initially anticipated.While increasing tonnage, a few bottlenecks were discovered and overcome in areas such as filtration and cyanide destruction. There were also recovery issues which were addressed in areas such as grind and sulfide leach. This paper focusses on the first complete year of operation ending September 30th 2015. A process description and the flowsheet are presented below and it will then go into detail about operational, metallurgical, mechanical and design issues experienced during the year."

Jan 1, 2016

By H. Hao

This paper outlines the development of a 2-D axisymmetric mathematical model to predict the evolution of temperature during the Direct Chill (DC) casting of AZ31 magnesium billets. Model predictions of temperature have been compared to measurements made on an industrial DC casting machine at Timminco Ltd, in Haley, Ontario. These measurements have been used to fine-tune the thermal boundary conditions employed in the mathematical model, The model, which is based on the commercial finite-element code ABAQUS, has been developed as part of a strategic project aimed at improving the DC casting process for light metals through a reduction in casting related defects and increased productivity.

Jan 1, 2004

By G. P. Gormley

"Future open pit metallurgical coal mines in western Canada will be developed in complex geological environments. The success of these operations will be influenced by the mine operators' ability to prepare accurate mine plans and to predict and, subsequently, 10 control both out-of-seam dilution and coal recovery. Quintette Coal Limited has been mining its tightly folded and severely faulted Mesa depo sit at annual rates of up to 9 Mt of raw coal, since October 1982. Ongoing development drilling combined with continuous utilization of blast hole information, has been required to achieve an acceptable geological data base for short range mine planning. Thrust faulting has been a primary geological cause of difficulty in selectively mining waste and coal, which has resulted in higher than expected dilution in plant feed. The same geological phenomenon has also increased reserves by 6.3% and allowed for expanded mine plans to include a lower thrust plate, ultimately doubling the mines original reserve base. This paper illustrates the geology of the Mesa deposit and the type of work involved in its interpretation. Regional GeologyThe Quintette Coal Limited (QCL) property is located in the Peace River Coal Field of northeastern British Columbia. In this area, northwesterly-trending folds of the Rocky Mountain foothills are commonly cut by multiple, low-angle thrust faults, which dip to the southwest. The Lower Cretaceous Gates Formation, of near shore continental origin, contains 5 to 7 mineable seams of medium volatile bituminous metallurgical coal (Figs. I and 2). These seams normally range in thickness between 0.75 m and 9.5 m and have an aggregate thickness of between 15 m and 22 m."

Jan 1, 1988

By D. F. Scott

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE REGION of Western Canada covered by this re-port lies between the Precambrian rocks of the Canadian Shield and the structurally deformed rocks of the eastern Cordillera, extending northward from the international border to the 60th parallel. It is some 487,000 square miles in area, with a total sedimentary fill of about 535,000 cubic miles0>. It includes parts of the prairie provinces of Manitoba, Saskatchewan and Alberta and the northeast corner of British Columbia and forms part of the geological region known as the Interior Platform, commonly referred to as the Western Canada Sedimentary Basin. The bedrock comprises carbonates and evaporites of Paleozoic age that lie on Precambrian crystalline rocks and are over-lain by a relatively thick blanket of Mesozoic and Tertiary elastic rocks. The nearly flat-lying bedrock, covered by a thick mantle of glacial drift, forms the Interior Plains physiographic province."

Jan 1, 1970

By C. H. Hopper, D. R. Derry, H. S. McGowan

"The property of Matachewan Consolidated Mines is in the Matachewan area on the west side of Montreal river. It lies in the western extension of the Kirkland Lake sedimentary belt. The first discovery of gold on the property was made by S. Otisse, in 1916. The property was taken over by Ventures, Limited, in 1933 and production commenced in late 1934. To date (December 31st, 1947) it has amounted to 2,308,800 tons, from which gold and silver to the value of $9,567,600 has been recovered. The mill is currently treating 650 tons of ore a day.GENERAL GEOLOGYThe deposits lie close to the south contact of a belt of sediments striking in a general east-west direction. The sediments, presumed to be of Timiskaming age, consist of light buff arkose and greywacke, containing small pebbles. The Keewatin volcanic rocks to the south are andesites or basalts with cuff and agglomerate bands developed especially near the contact with the sediments. The lavas and sediments are overlain by relatively flat-lying sediments of the Cobalt series to the south and west of the mine, but these later sediments are not involved in the mineralization under discussion. The Keewatin lavas and Timiskaming sediments are intruded by dykes and lenses of red syenite porphyry that have approximately the same strike and dip as the invaded rocks. Later diabase dykes, apparently post-ore, run in a north-south direction and cut all rocks except the Cobalt series.OREBODIESThe gold-bearing mineralization forms bodies of two different types: (1) Within the volcanic rocks irregular orebodies with limited vertical extent. These consist of a series of flat-dipping quartz stringers and adjacent lavas and /or cuffs fractured, bleached, and mineralized with pyrite and gold. They are higher grade than the second type (average about 0.16 oz. gold a ton) and formed the main source of ore for the first 5 years of production. They are described in more detail than can be given here in an article by C. H. Hopper (4). More recent work on deeper levels has failed so far to find orebodies of comparable grade, though low-grade mineralization of a similar type does occur on the projected rake of the main group of the 'basalt type' of orebodies."

Jan 1, 1954

By C. Yanqui

"Discontinuum Mechanics is based on two foundations: the idealization of the internal structure of substances, and the principle of the arithmetic mean value. For a linear discontinuum, the methods of Crystallography are used to describe their structure, in which nodes stands for the position of the homologous points such as molecules, grains, or any other motif. The principle of the mean value states that the value of any discrete function at a node is equal to the arithmetic average of the values of this function at the neighboring nodes. This principle leads to an elliptical linear differential equation of the second order, with coefficients given by the statistical second moments of the Cartesian components of the metric vector. As long as those coefficients are components of a symmetric second-order tensor, there are three mutually perpendicular directions, in which the variances reach their extreme values and the covariances are zero, showing that the mean value principle transforms the discontinuum into a statistically equivalent orthotropic continuum.The application of Discontinuum Mechanics to linear rock masses is simple and direct. It is sufficient to define the motif as the plane of geological discontinuity, and the metric vector as the normal vector to this plane, whose magnitude is the spacing between two consecutive planes belonging to the same set of discontinuities. Furthermore, heterogeneities of rock masses can be also included in this description by substituting the plane of discontinuity by a zone of weakness. In this way, the magnitude of the normal vector results from the product of the spacing and the RQD or the RMR. In going further in this theory, at least three conclusions show up. First, in the evaluation of rock masses, it is necessary to determine the orientation, spacing, and RMR for each set of discontinuities. Second, the conventional method of finding the principal families from the contours of equal concentration of poles on the stereographic projection excluding the spacing does not have any physical meaning. Third, any problem of rock mechanics can be solved in a rigorous and reliable way by integrating the differential equation of the mean value."

Jan 1, 2015

By R. Tipman

"In 25 years, processing of tar sand progressed from two small pilot plants to two major commercial operations owned by Syncrude and Suncor. These plants mine tar sand and extract the bitumen which is then converted into a synthetic crude oil. Considerable research on extraction of bitumen from tar sand has been undertaken by these two companies as well as other major oil producing companies, private individuals, universities and the federal and provincial governments. These studies have produced a number of alternate processing schemes which have yet to be commercialized. The producing companies are focusing their efforts on achieving increased processing efficiency, which includes improved bitumen recovery, reduced unit cost, energy conservation, and equipment reliability. In this review, the Syncrude process and examples of new process developments will be briefly described. IntroductionTwenty-five years ago, tar sand processing was limited to two pilot plants owned by Cities Service Athabasca Ltd., and Great Canadian Oil Sands. Earnest Manning was Premier of Alberta and was inviting proposals for the construction of a commercial tar sands plant. The invitations called for a much larger operation than those which had been undertaken in the past. All of the previous attempts at commercial operations up to 1960's had failed, largely because of a poor technical understanding of the process requirements, lack of suitable equipment, and lack of adequate capital. The previous record was not good. The pending new large scale plant was based on improved but not proven technology and equipment, which were developed from the pilot plant studies. In addition, the surplus of conventional oil in Alberta and low world oil prices were factors reducing the need for such a plant."

Jan 1, 1987

By B. Haneman, J. A. Gorst, W. Slabbert

"The Bayer process involves the digestion of bauxite in caustic liquors at high temperature and pressure. Typically the digestion section of the plant involves the heating of liquors up to the digestion temperature followed by flashing of the digestion product to atmospheric pressure with the flashed steam used to pre-heat the incoming cold slurry. Despite the heat recovery, the digestion process is a high consumer of energy. The application of tube digestion technology in such plants has resulted in significant improvements in refinery energy efficiency with associated benefits of process simplification and refinery flow sheet capital cost reduction. This paper reviews the potential application of this technology to other metals within the non-ferrous industry.THE BAYER PROCESSA typical Bayer flow sheet is shown in Figure 1. The raw feed material bauxite (containing aluminium hydroxide as gibbsite Al(OH)3 and boehmite AlO(OH)) is digested in caustic liquors (caustic soda is the solvent) at high temperature and pressure. This process extracts the alumina and silica and any carbon present on the ore. The slurry is then flashed down to atmospheric condition allowing for heat recovery from the flashed vapour and producing slurry supersaturated in alumina.Following the digestion process the mud is removed via thickening and then pressure filtration to remove fine particulate and produce a clarified liquor with dissolved alumina in solution. The resulting pregnant liquor is then cooled allowing the alumina in solution to precipitate as aluminium trihydrate Al(OH)3. The precipitated hydrate is then filtered and washed and classified into fine and coarse fractions. The fine material is returned to the precipitation process as seed while the coarse fraction is calcined at high temperature to produce alumina. The filtrate from the filtration process (spent liquor) is then heated by the incoming pregnant liquor before being fed to an evaporation process which produced the strong caustic liquor required in the digestion process. Finally, the mud from the thickening process is washed to recover caustic and then fed to tailings ponds. The washer overflow is then mixed with the digester product to increase super-saturation."

Jan 1, 2012

By Sh. Karimidorabati

In the construction industry, project changes constitute a major cause of delay, disruption, cost increases, poor quality and unsatisfying performance. They are also known as a main factor of litigation between the owners and constructors. Construction projects are essentially process-based, and with the critical role of Information Technology (IT) in this industry, projects, especially mega projects, are being managed remotely. The volume of data and documents, such as Requests For Information (RFIs), different types of Change Requests (CRs) and Project Change Notices (PCNs), being transferred and exchanged amongst the stakeholders of a project is considerable. The circulation of these documents amongst project stakeholders still heavily relies on two methods or levels for management of change process; Conventional (fully paper-based, Faxes, Snail mails) and Electronic or semi-automated (Email, Internet, PDF files). These two methods are dependent on human discipline to follow specified processes which often break down because of human nature. This creates serious compliance problems. It is hypothesized here that fully that automated process-based management of change can lead to better compliance, more efficient management of change, and reduction of time and cost of data exchange. An approach of doing this is presented in this paper. Ultimately, its impact should improve project performance. Conclusions are presented on time savings and improved compliance.

Aug 1, 2013

By S. A. Kenzap

Risk & Uncertainty ? Uncertainty about a situation can often indicate risk, which is the possibility of loss, damage, or any other undesirable event. Most people desire low risk, which would translate to a high probability of success, profit, or some form of gain. Risk = Likelihood x Consequence Risk is the possibility of loss, damage, or any other undesirable event.

Oct 1, 2010

By V. Shumila, T. Butler

Microseismic monitoring systems listen to a rockmass and record ground vibrations associated with brittle rock fracture. Modern systems record continuously and can identify as many as one thousand small and possibly larger magnitude events occurring each day from induced stress change and redistribution. This paper presents examples of the real time use of microseismic information in mining applications. It shows how alerts can quickly identify large magnitude events or unexpected clusters of seismicity and how seismic re-entry protocol can help to improve safety decisions. Additionally, newly developed advanced analysis techniques applied to mine seismic data sets are shown including the use of clustering methods to see into a cloud of seismic data to identify significant activity and quantify possible planar features. The use of source parameter trend analysis is shown to be a beneficial method for interpreting changes in relative stress levels. Seismic moment magnitude distributions are analyzed using the TGR (Truncated Gutenberg Richter) and TMD (Tapered Moment Distribution) methods to estimate bvalue and expected maximum magnitude. Seismic hazard analysis is shown as a useful way to simplify a dataset and highlight seismic hot spots. The rockmass response to excavation is a complicated spatial and temporal process and microseismic monitoring is a method that can be used to help understand the location and mechanics of failure occurring in the rock ultimately helping to improve safety and productivity at a mine site.

Jan 1, 2015

By Christopher Boys

"Abstract -Many water inflows in Saskatchewan potash mines are linked to salt anomalies. Potash ore and three anomalies in the PCS Cory potash mine in the Patience Lake Member of the Prairie Evaporite Formation were studied to understand the processes involved in their formation. Another goal was to find geological indicators of the proximity of anomalies. A geological model that relates the potash to the salt anomalies has been developed.Up to five post-burial facies may be recognized . These range from carbonate-mud collapse breccias to bedded sylvinite, and probably result from post-burial leaching. ln this model, the same fluids that caused widespread recrystallization and possibly enrichment of the potash salts, started by dis­ solving huge cavities in the evaporites . The effects of the leaching were highly variable, indicated by selectively preserved delicate laminae and chevron textures, to deformed and totally dissolved salt beds . ln at least two major events, Late Devonian and Cretaceous, collapse structures may have acted as conduits for overlying formation waters to cause pervasive leaching and recrystallization of the Prairie Evaporite Formation .Geological indicators of the proximity of an anomaly may include: a change in Insoluble seam color from greenish-gray to mottled brown and greenish-gray, unusual local increases in ore grade, large patches (e.g., >200 cm2) of sylvite-poor potash crosscutting units near the top of the ore zone, and drops in topography >10 m of the marker seams. Anhydrite was more common in an anomaly than in ore. The local abundance of anhydrite in ore may indicate the proximity of some salt anomalies.Once an anomaly has been encountered, indicators of a major collapse feature may include: stretched clay seams, folded beds, small collapse features (1 m to 20 m), numerous washouts, or split clay seams with injected salt. Any number, or none, of these indicators may be found close to a major collapse feature."

Jan 1, 1993

By Horace Freeman

"IN THE writer's opinion, the most important industrial re-search problems in Canada concern development of technology for the treatment and commercial utilization of the recent discoveries of v.ast quantities of easily concentrated iron ores in both eastern and western Canada. They exist in both magnetite and hematite forms. The subject is doubly important because of the lack of metallurgical coking coal in Canada. Methods for utilizing our lower grade eastern and western coals for reduction purposes must be developed. We are fortunate in our supplies of oil and gas, which can supply the heat requirements for processing or for thermal electric plants, which are now competitive with hydro-electric plants in the industrial areas. These are among the reasons which have prompted the writer to continue the development of the co-current rotary kiln direct-reduction process outlined •in his report to this Institute at the 1956 Annual Meeting ( 1) in the face of the scepticism which has surrounded the numerous costly failures in 'sponge' or 'direct' iron production. The work involved in bringing the concentrating ores of Canada to the metallic state involves, firstly, concentration of the ores; secondly, preparing the concentrates for reduction; thirdly, reduction of the 'reconstructed' ore; and finally the steel making process. These briefly will be dealt with in order, giving emphasis to the most important of these steps, the reduction process which is the main subject of this paper."

Jan 1, 1959