Search Documents

By F. M. Makarinsky

"This paper describes the conversion of conventional froth flotation cells to open-trough type bank cells, with 'buried' vertical metal partitions. These changes have resulted in: total froth removal along the full length of each bank of cells; extended flotation cell retention times; and has extended the life of the metal components, particularly towards the upper flotation cell areas.INTRODUCTIONOver the past twenty years, the flotation cells used at Falconbridge Limited, Sudbury operations concentrators, have gone through major physical changes. The various concentrators generally started with 100 cubic foot Denver Sub 'A' flotation cells. From these units, we progressed to 'converted' DR units, and/or Denver DR units, if purchased new. (Figures 1, 2, 3)In 1980, the Strathcona concentrator started to pay more attention to the 'front end' rougher flotation cells. Initially, the converted DR flotation cells had 'cut-outs' removed (Figure 4) at all upper vertical cell partitions, towards the ff9th lip areas, in order to get additional froth removal."

Jan 1, 1985

By William Skinner, Jim Pae Lem, Massimiano Zanin

It is well known that the specific density of minerals has adverse influence on the classification performance of a hydrocyclone, particularly when liberated high density minerals such as gold or uranium are present in sulphide ores. These liberated heavy minerals often misreport to the underflow and recirculate to the system. Such phenomena does result in serious issues in a closed-grinding circuit, such as overgrinding, leading to production of flaky particles (as in gold) or ultrafines, in addition to increased energy inefficiency. In plants which present gold liberated at coarser size, loss of gold due to cyclone inefficiency is sometimes prevented by incorporating gravity concentrators into the grinding circuit to recover the gold. The work reported in this paper looks at whether the effect of density will prevent successful rejection of liberated U-bearing minerals in the –10µm size range of a plant re-cleaner feed, which is necessary to minimize penalty U accumulation in a copper concentrator. The study was carried out using a cyclone rig with spigot diameter of 0.25 inches in combination with batch flotation. It was found that the density effect is almost negligible at particle sizes below 10µm. Consequently, the liberated U-bearing particles finer than 10 µm were successfully removed in the overflow stream as rejects and hence U grade in the copper concentrate remarkably reduced, by 16 ppm. Based on the results, de-sliming of the re-cleaner feed was recommended for plant trial and implementation.

Jan 1, 2016

By R. A. L. Drew, C. A. Rodríguez González, Caleym W. F.

This work addresses the need of new refractories for copper converters. Technological improvements and environmental regulations for chromium containing refractories have generated this need. Chemical interactions, mechanism of penetration and the effect of oxygen potential and temperature in the system Cu2S-FeS-SiO2-O2 are presented for two refractories: a burned magnesite chrome brick (typically used by the copper industry) and a chrome-free spinel direct bonded brick. The main difference determined in the refractory performance was the blister copper penetration resistance; burned magnesite chrome brick is penetrated while direct bonded brick is not. These results are very promising since blister copper penetration has been reported as the major cause of refractory wear. The results are explained in terms of refractory porosity and wetting characteristics.

Jan 1, 2004

By E. M. Timoshenko, A. V. Tarasov

The results of laboratory, bench-scale and semi-commercial investigations of a method for adding surfactant (technical-grade lignosulphonate) to the process of pressure leaching of nickel-containing pyrrhotite concentrates have been discussed. Lt has been demonstrated that feeding of technical-grade lignosulphonate distributed along the length of an autoclave ensures a reduction in its requirement by a factor of 1.5 to 2 as compared with single-point feeding; it also results in a decrease by 5% in the unit requirement of metallized iron-bearing precipitator in the process of non-ferrous metals precipitation and reduces by 0.05 to 0.1% (abs.) the nickel and copper contents in the tailings of the given process. Technical solutions have been proposed for commercial introduction of the process.

Jan 1, 2004

By L. Rahnenfuhrer

"Hoisting equipment is a vital part of the operation of most producing mines. Safety and continuation of operation necessitates ultrasonic preventive maintenance inspection on a regular basis.Ultrasonic inspection of hoist shafting, brake linkage and draw bars will contribute to a safe operation and can prevent costly unscheduled shut-down time. With little dismantling, ultrasonic testing techniques can be applied to. determine the conditions of shafting and linkage in hoisting equipment, mining equipment and other miscellaneous mining equipment."

Jan 1, 1969

By J. D. Corbett

The spatial coincidence of the seven anomalies is obvious, even though the self-potential is offset northward. Because the ratio, as an indicator of conductivity, is a relative estimate at best, concise interpretation is limited in almost every instance to the location of a conductor or conductor axis. When related to the initial phase of an exploration program, magnitudes and ratios similar to those obtained from any one of the methods described, would be sufficiently attractive to warrant further investigation. The compilation shown is an empirical comparison of actual field results and no emphasis has intentionally been placed on the relative merits of one method in respect to another. Too many additional factors, i.e., size, depth and conductivity of overburden, etc., that cannot unequivocally be answered, enter into such a comparison before a relative evaluation can be made.

Jan 1, 1961

By K. Wood, L. Duval

"The paper discusses the approach used to add a new, separate 5000 t/d copper-zinc treatment circuit to an existing, 1650 t/d copper circuit, essentially within the existing mill building. Temporary installation of new equipment allowed renovation and expansion within existing operating areas. Production in the original circuit was maintained at rated capacity throuqh0ut the construction period through close co-ordination between operating and construction groups. Downtime for circuit and service tie-ins was minimal. Both circuits are described briefly.For presentation at Canadian Mineral Processors Conference Ottawa, January, 1987.INTRODUCTIONLes Mines Selbaie is located in the Abitibi region of northwestern Quebec, in what has recently become better known as the Casa-Berardi-Joutel area. Les Mines Selbaie is operated as a joint venture project managed by Selca Division of BP Canada Inc. and owned 55% by BP Canada, 35% by Esso Minerals Canada and 10% by Trans Canada Pipelines."

Jan 1, 1987

By Real Daigneault, François Robert, J. Paul Golightly, Jean-Yves Cloutier, Jayanta Guha, Pierre Pilote

"The Casa-Berardi East, Center and West deposits, located in the Archean Abitibi, Sub province, are hosted by volcanic and sedimentary units of varying compositions, less than300 m from the Casa-Berardi fault (CBF). The CBF, a brittle structure, represents an increment in the structural evolution of a regional-scale deformation zone showing ductile-brittle behavior known as the Casa-Berardi deformation zone (CBDZ). The CBDZ is characterized by a mylonitic Sc1 foliation which is folded a.n4 deformed by a later sczfoliation in high strain zones.Four generations of quartz vein and fracture systems have been recognized within the Casa-Berardi deposits. Most economic gold mineralization, occurring in the second generation system, is found within high strain zones. This system hosts three types of mineralized structures: (1) banded quartz veins; (2) swarms of veins and mineralized host rocks; and (3) disseminated sulphides along fractures. An early carbonate hydrothermal alteration zone (pre- to syntectonic) surrounds the deposits. Alteration associated with gold mineralization is contemporaneous to late ( syn- to post-tectonic) relative to the development of progressive deformation in the CBDZ. The geological characteristics and paragenesis of the four quartz vein and fracture systems developed as an integral part of the geodynamic evolution of the Casa-Berardi deformation zone."

Jan 1, 1990

By J. G. Peacey

"Canada has a special place in non-ferrous pyrometallurgy because it is the only country in the western world that is a significant producer of all the major non-ferrous metals; aluminum, copper, lead, magnesium, nickel and zinc. This large non-ferrous pyrometallurgy industry has developed because of Canada's abundant mineral wealth and energy resources. Table I summarizes the number of primary non-ferrous production facilities in Canada and their share of western world production.Production of non-ferrous metals is a mature, capital intensive business and its basic processes have been in use for many years. Nevertheless, these processes have continued to evolve in response to changing needs and external pressures; such as the energy crisis of the early seventies; historically low metal prices in the early eighties and the continuing pressure to reduce plant emissions and improve in-plant working conditions. Canada's major metallurgical companies: Alcan, Cominco, Falconbridge, Inco and Noranda have played a leading role in pioneering new process technology and continue to meet the difficult challenge of keeping their operations competitive in the global metals market. This paper will try to give an overview of the major developments in non-ferrous pyrometallurgy, largely from the Noranda and Canadian perspectives, highlighting the current status of process technology and possible future directions.AluminumCanada has the world's second largest aluminum smelting industry and its capacity has expanded rapidly in recent years with the completion of several large projects in Quebec. The location and capacity of the Canadian aluminum smelters are given in Table 2. All these plants use the Hall-Heroult process, that was invented over a century ago but over the last twenty years considerable improvements have been made to increase productivity, reduce power requirements and emissions.The developments in aluminum cell technology can be illustrated by the experience at Noranda Aluminum. In 1971, Noranda Aluminum started its first pot line using Kaiser's P69 prebake cell, which was considered, at that time, the best available technology. The P69 cell was designed primarily for high productivity, operating at 150 000 amps and high current density to produce just over tonne Al per cell-day. The P69 cell is a simple design, typically operating at about 88070 current efficiency and 15 800 kWh/tonne Al. When Noranda Aluminum decided to expand in 1980, the Alcoa 697 cell was selected as it then represented the most proven, stateof- the-art technology. This cell is similar to that installed at Alcan's new Grande Baie and Laterriere smelters and is designed to operate at 180000 amps and 93070 current efficiency, producing about 25070 more aluminum per pot-day than the P69 cell using about 15070 less power. The 697 cell has a much more sophisticated cell design, with very good balancing of the magnetic field giving a flat metal pad and allowing efficient operation at the higher amperage. Alumina is fed via point feeders that provide an almost continuous feed allowing close control of the alumina level in the bath and the use of low-ratio bath composition, giving much higher current efficiencies."

Jan 1, 1991

By P. Rosario

"Current industry practice for HPGR assessment and sizing relies on conducting a series of tests using pilot-scale machines with roll diameters of 700 mm to 1000 mm. Substantial amounts of sample are required for such pilot test programs, typically 1 to 10 tonnes of the sample is needed depending on the level of study and complexity of the resource. Collection of large quantities of representative samples during the early stage development is challenging and expensive, thus significantly hinders the HPGR technology from being incorporated into early-stage designs. A robust and reliable laboratory test is therefore needed to allow a fair consideration of HPGR for early stage projects. With support from the Canadian Mineral Industry Research Organization (CAMIRO), the NBK Institute of Mining Engineering at the University of British Columbia (UBC) developed a suite of Piston Press bench-scale tests that correlated to pilot and full scale HPGR operating information (Davaanyam, 2015; Davaanyam et al, 2015; McClintock, 2018). The Piston Press Tests (PPTs) are capable of assessing the HPGR technology at the scoping, pre-economic analysis (PEA), and pre-feasibility (PFS) stages of project development. This paper will briefly describe the theory on which the PPTs are based, and then presents a case study conducted for a copper deposit to show how the PPTs are being used for scoping and pre-feasibility level studies. Specifically, the PPTs are being used to provide information for preliminary sizing and selection of an HPGR and to assess the effect of ore variability on HPGR performance. The results are also applied to developing HPGR circuit designs and can be incorporated in simulation so that optimum design parameters can be selected.INTRODUCTION It is widely accepted that high pressure grinding rolls (HPGRs) offer a viable energy-efficient solution for the modern comminution flowsheet design. Table 1 summarizes selected examples of HPGR applications in the hard rock mining industry. The main benefits of HPGRs are energy savings which leads to lower operating costs, and its stable operating characteristics that can better cope with variations in ore hardness when compared to the conventional SAG mill-based comminution circuits."

Jan 1, 2019

By Gobbs C., J. Lam

"The Eagle East project, accessed from the existing and operating Eagle Mine in the Upper Peninsula of Michigan, is an underground base metal project currently in execution by Lundin. This paper will provide an update on several aspects of ventilation including use of a twin-decline access, innovative airflow crossover arrangement and construction ventilation methodology. Integration into existing mine ventilation systems including construction methodology will also be covered. Performance benchmarks and lessons learned are discussed across these topics.INTRODUCTIONLundin has owned and operated the Eagle Mine since 2013. This hard rock underground mine is located in the upper peninsula of Michigan, USA. High-grade nickel ore is mined using sublevel open stoping mining methods and trucked to surface via haul ramp. The mine, having been in production for four years, is nearing the completion of the initial orebody. A satellite orebody 2,000 meters East of the current workings and approximately 900 meters below surface, was identified that could extend operations until 2023. In 2016, Lundin approved the Eagle East project and construction began in 2017 (Lundin Mining Corporation, 2017).Due to proximity to the existing mine, Eagle East will be both accessed and serviced from the existing Eagle Mine. Ventilation at the Eagle Mine uses two fresh air intakes with direct fired combustion heaters; one at the mine portal feeding fresh air into the ramp and one at a fresh air raise located near the Eagle deposit. The primary ventilation circuit is powered on the exhaust air side, with two 700 hp exhaust fans located at a single return air raise. Underground, fresh air is distributed through the main access decline and fresh air raise (FAR) to the production levels and controlled with mechanical regulators on the exhaust side. The exhaust air is collected through return air raises with a collector/transfer drift on 250 Level and then to the surface through a return air raise (RAR)."

Jan 1, 2019

By Marke Wong

? Vietnam?s economy is growing so fast that gross domestic product (GDP) growth remained above 8% in 2005 and exports are rising steadily at 25% per year. ? Demand for electricity is expected to increase 18% per year through 2010 requiring an additional estimated 7,547 MW before 2010 ? Domestic coal demand is expected to be over 45 Mt by 2010. ? The Quang Ninhcoal deposits are estimated at 6.5-7 billion tons (350m) Vietnam News Agency. Saturday, May, 6, 2006. ? National resources are now estimated at 10 billion tonnes; not including a relative new coal bed discovery estimated at 210 billion tonnesin the Red River Basin.

May 1, 2006

By Daniel Hodouin, Mélanie Proulx, Claude Bazin

"Collector and frother are commonly used to induce the floatability of valuable minerals in flotation plants. These reagents are usually distributed down a flotation bank or sometimes added in a single location at the top of the bank. A review of the literature and some experimental results obtained from laboratory and full scale trials indicate that the way flotation reagents are distributed down a flotation bank may influence the flotation response of coarse particles. The paper summarizes these observations which show that the distribution of reagents is a potential tuning variable for process optimization.IntroductionFlotation is in many cases the only way to concentrate sulphide and some oxide minerals. Flotation is a concentration process that uses particle surface composition to induce the selectivity by mean of hydrophobic reagents. The influence of particle size on flotation was firstly analyzed in the 50's1·2 and intensively investigated in the 70's, early 80's and 90's3-18. Most of the observed results show the existence of an optimum flotation size range9 whose recovery is not significantly influenced by a reduction of collector dosage""18. This result brought the idea of using a small portion of the total collector dosage at the top of a rougher bank and to distribute the remaining through the end of the bank to ensure sufficient collection of the coarse particles that need more hydrophobic coverage to attach to air bubbles and be lifted to the surface.This paper discusses the idea of using the distribution of reagents down a flotation bank to tune the operation of the process. Unlike the literature on the effect of reagents (collectors, frother...) dosage that is dense, little attention has been put on the distribution of reagents in a flotation bank. Although research on this subject has not been pushed very far, some operators have recognized the potential of a strategic addition of reagents down a flotation bank19. Except for a few exceptions, the proportions of the reagents to be distributed down a flotation bank are decided according to operator's experience instead of process analysis in relationships with particle size. This paper recalls observations made by different researchers that lead to the idea of using the distribution of reagents as a tuning variable for the flotation process. The paper does not present a detailed analysis or optimization scheme for tuning the distribution of reagents, but analyzes some plant and laboratory results with a view toward the development of a testing methodology and ultimately a validation or rejection of the idea."

Jan 1, 1998

By Fernand Dubuc

"The New Pascalis property is situated in Louvicourt and Pascalis townships, about 200 km east of Val d'Or, Quebec. It is made up of 38 claims under option to SOQUEM since August I, 1981 during which time SOQUEM has earned a 60% interest. The property is underlain by archean basaltic volcanics that have been intruded along the west boundary by the Bourlamaque batholith, and by north -trending dykes.The 1982 disco very is related to the re-evaluation of a 1931-gold showing located in the southeastern part of the property, a combination of the presence of a weak IP anomaly at the eastern end of the showing and overburden stripping at that location, resulted in the discovery of a mineralized diorite dyke.The dyke, which strikes N 20 ° Wand dips vertically , has intruded E-W striking agglomerates. The dyke contains south dipping, gold-hearing quart z-tourmaline-pyrite veins that are distributed in a ladder-type arrangement. Visible gold may he observed in drill core, and is generally associated with pyrite porphyroblasts.Diamond drilling has outlined th e dyke for a strike length of 300 11/ and a width of about 10 m, Result s of this drilling indicate, to a depth of 155 m, reserves of 834 000 metric tonnes grading 8.25 g Au/t un cut or 5.38 g Au/t cut to on e ounce. However, four deeper holes have added depth extension to 400m. Also, west of the dyke and within 150 m, other promising gold values have been intersected within quartz-tourmaline veins associated with other parallel dykes."

Jan 1, 1985

By E. Ozberk, N. Gibson, W. G. Davenport

"In the 1950s, Canada produced more than ninety-five percent of the non-communist world's nickel and achieved dominance in terms of production, technology and pricing policies.Over the past thirty years there have been dramatic changes in the nickel industry to the extent that Canadian production is now less than thirty per cent of the total.In this document we have presented statistics relevant to this transformation and reviewed the technology, particularly with regards to energy and environmental considerations.Under the new market conditions nickel producers are likely to face more difficult competition than they have encountered in the past.The economic scene and measured nickel reserves dictate that for the purpose of increasing production, new nickel smelters will not be built in Canada in the foreseeable future. However, in order to reduce sulphur dioxide emissions, Canadian nickel smelters will possibly go through some modifications or rebuilding.IntroductionThis paper presents a review of the Canadian nickel industry in relation to the world nickel industry. Major changes are described which have occurred in the characteristics of the nickel market over the last thirty years. The pre sent status of the nickel market with respect to Forecasting future trends is reviewed and attempts are made to predict what further changes will take place in the next two decades. Comparisons are made of the economics of producing nickel from sulphide ores and oxide ores and the advantages and disadvantages the Canadian nickel producers face.A brief critique of the existing and emerging nickel production technologies in Canada and the world is carried out and attempts are mad e to predict the changes which may take place in the foreseeable future."

Jan 1, 1983

By John Smith

"The RTZ Corporation PLCFrom a company's point-of-view, a good investment decision is one which results in the purchase of an asset that is worth more than it costs. Thus, in order to judge the merit of an investment opportunity, it is necessary to estimate the value of the assets to be acquired.Discounted cash flow (DCF) analysis has become widely adopted by companies in assessing potential new investments. The principle is a simple one: invest in projects which have a positive net present value, and reject those which do not. However, perhaps because of its apparent simplicity, DCF analysis is frequently misused. Good practice in the use of the technique is discussed, together with several common misconceptions.Sound analysis requires sound data; thus, the valuation process relies heavily upon a wide range of specialists to provide the basic input from which cash flow forecasts can be built up. The analyst must maintain close liaison with these specialists from the outset in order to ensure that the data provided is indeed relevant and complete.IntroductionBefore turning to the main subject of this paper ""How Companies Value Properties"", it is of interest to consider first a slightly different question ""Why do Companies value Properties""? In other words, for what purposes are such valuations prepared? Certainly the commonest, and probably the most important circumstance in which a valuation is required is when the company is considering an investment opportunity. This may be the direct purchase of a property or group of properties from a third party, but could also be the opportunity to develop a new operation or expand an existing one.A very simple objective in making any kind of investment is to make our shareholders richer than they would otherwise have been. That is, to make investments whose value to shareholders exceeds the consideration required to acquire them. Thus the investment decision focusses on the difference between an asset's value and its cost.This distinction between ""value"" and ""cost"" is an important one. Study of a company's balance sheet may tell a lot about the cost of this company's assets, but very little about their value. Then again, it is sometimes argued that a business should be bought because this will result in assets being acquired for less than their replacement cost. This merely compares one cost with another, it says nothing about value."

Jan 1, 1991

By P. Garritsen, J .. A. Blanco, M. C. Bell

"By 1994, Inco Limited will lower sulphur dioxide emissions from the Copper Cliffsmelter by 60% to 265 000 tonnes/year, primarily through implementing two key process changes. First, new milling technology will permit economic rejection of additonal pyrrhotite prior to smelting. Second, a bulk coppernickel concentrate will be oxygen flash-smelted, thereby eliminating the existing multi-hearth roasters and reverberatory furnaces . All copper will be recovered in the matte separation plant as a nickeliferous chalcocite, and will be oxygen flash-smelted for blister production. This paper outlines the development of the project and describes the process, including the flash furnaces, new sulphuric acid plant and additional oxygen plant.IntroductionInco 's SO2 Abatement Program will lower sulphur dioxide emissions at Sudbury from the current levels of 685 000 tonnes per year to 265 000 tonnes per year by 1994 as required by Ontario' s countdown on acid rain regulations.It is the high tonnage of sulphur mined that creates the magnitude of the SO2 emission problem at Sudbury. At a production rate of 240 million pounds of nickel per year, Inco mines 12 million tonnes of ore. At 10% sulphur it mines 1.2 million tonnes per year of sulphur. If Inco did not fix any of this sulphur it would be emitting 2.4 million tonnes per year of sulphur dioxide-about as much as all other Canadian emissions. Today, however, Inco is already fixing 70% of the SO2 in ore, in several ways : mostly as sulphur in pyrrhotite rejected to tailings in the milling operations; as acid from the roasting of pyrrhotite and some nickel concentrate at the Iron Ore Recovery Plant (lORP) and some as liquid S02 from the copper flash smelting furnace. By fixing 70% of the sulphur the current allowable SO2 emission levels of 685 000 tonnes per year is met. Total sulphuric acid production is currently 450 000 tonnes per year and in fact, the 10RP operation is being continued only to maintain established acid markets.Historically emissions have been reduced from the 2 000 000 tonne per year level to the current level of 685 000 tonnes per year by rejecting pyrrhotite from the smelter feed, and 70% of the SO2 containment problem at Sudbury has already been addressed.While Inco's profits are large at current nickel prices, most people have forgotten that back in 1982 Inco was losing a million dollars a day. Inco did make a dramatic response to this economic stimulus. The Ontario Division increased productivity by 65% and lowered costs to become the lowest cost nickel producer."

Jan 1, 1990

By M. Piard

Fires and explosions are not likely to originate in clean gobs above pillar faces steadily driven through a solid panel in order to effect a complete extraction. As. to the storage which such a process implies where the market is intermittent, its cost will never equal that of abandoning large pillars in a fully developed property. Much less will that cost, thanks to the big sizes obtained, ever approach that of cleaning wet and dirty crushings robbed at great expense from small pillars exposed to many years of roof pressure. Even thick seams under bad roof may be fully extracted without the help of filling material. Fatal accidents from falls of roof owing to the great height of excavations, losses in coal, and the danger from fire, have compelled operators in South Staffordshire, England, to discontinue the stall-and-pillar system at one time supreme in the district, and to successfully adopt the following plan: A retreating' longwall is run along the top coal, as the first working; the bottom coal is taken in the same manner, after the fallen roof has become sufficiently consolidated to allow the mine to be reopened. A similar plan is suggested in this paper in order to deal with the outcropping and pitching seams found in the Kootenay measures.

Jan 1, 1930

By D. H. Stonehouse

"ALTHOUGH final statistics are not yet available concerning Nova Scotia' s mineral production for 1958, it is estimated that the value will be slightly lower than that of 1957. In making this statement it is but fair to say that one year ago a reduction in mineral value was also forecast (for 1957 as compared with 1956) and final figures from the Dominion Bureau of Statistics ($68,058,743) indicated, instead, an increase of $2,000,000 over 1956. However, 1958 did bring problems to the industry which would indicate a drop in production value. The estimates figure for 1958 is $64,000,000. COAL Coal production came from 28 mines, 5 less than were operating since 1957. There were 5,269,896 tons of coal produced by 1,978,512 man-days' labour, for a tons per man-shift of 2.66 (0.05 higher than during 1957) or an increase of 1.9 per cent over the 1957 all-time high for this Province. This record has been established as a result of concentrated efforts to mechanize the coal mines of the Province, and it is hoped that it will be bettered during 1959. Collieries which showed some production for 1957 and none for 1958 were the McGregor at Stellarton, the Franklin at Sydney Mines, the MacLellan, the Rose bank No. 2 and the Rose bank No. 3 at Inverness."

Jan 1, 1959

By Ling Wu

The development of pyrometallurgical technologies has been focused on new smelting reactors, but the proposal for new converting reactors has been substantially lower. Up to today about 80% of copper matte is treated by the traditional P-S converters which have the weakness of pollutant fugitive emissions. Therefore, the continuously converting processes for treating molten matte have been studied and developed. In July 2017 the "oxygen-rich side blowing smelting + multi-lances top converting & fire refining" continuous copper treating process was commissioned. This process was designed by ENFI and YanTai GuoRun Copper Smelter. In this process, oxygen rich side blow technology is adopted for smelting, which is a new type of side blowing smelting furnace to produce high-grade copper matte. The converting adopts the horizontal multi-lances top-blowing continuously converting process, which eliminates the transportation of molten melt and the SO2 fugitive emission. The intermediate products of this process, copper matte and blister copper is fed into the furnaces respectively through launders. This new process is more advanced, more reliable and more environmentally friendly. Until now, this process in the GuoRun copper smelter is operating smoothly. An increasing number of projects which use this process are under design and construction in China. INTRODUCTION At present, there are many advanced smelting technologies for copper concentrate, such as oxygen bottom blowing smelting, flash smelting, top lance smelting (including ISA and Ausmelt furnaces smelting), side blowing smelting, Mitsubishi smelting, etc. At the same time, there are many copper matte converting technologies such as oxygen bottom blowing continuous converting, flash converting, Ausmelt top lance converting, horizontal multi-lances top blowing converting, Mitsubishi converting, P-S converter converting, etc. The final blister copper fire refining technology mostly adopts rotary anode furnace. Therefore, in the process of processing and extracting the copper from concentrate to produce anodes, there are dozens of technology combinations. Among them, the non-continuous converting technologies for molten or cold matte are often adopted in the converting process. The traditional P-S converting technology had been utilized for over one hundred years, with a mature, reliable and simple operation, also has advantages in the secondary scrap smelting of a wide range of quality. However, due to its batch operation, frequent roll in and out, poor sealing, considerable air infiltration, needs for ladles for molten phases transportation and other characteristics, the technology has a serious pollution problem due to fugitive SO2. At the same time, in the cold matte converting technology, the molten matte needs to be cooled and then processed. The sensible heat of the molten matte cannot be recovered, and the preparation process is needed in the process. Therefore, both energy consumption and investment are relatively higher.

Jan 1, 2019