Search Documents

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By Colleagues from Process and Operation departments, Guy Chevalier

"QCM's pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented.This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.INTRODUCTIONAt the Québec Cartier Mining pellet plant, continuous improvement programs are aimed at increasing levels of consistency and improved chemical, physical and metallurgical properties. This is being accomplished while still maintaining pellet plant production volumes to satisfy market demands.QCM produces three types of pellets for blast furnace use: acid pellets, designated as ""BHF"", fluxed pellets, designated as ""BAF"", and low silica fluxed pellets, designated as ""BSA"". For direct reduction, a low silica acid pellet or DR pellet, designated as ""BBS"" is produced. This low silica DR pellet is used in Midrex and HyL shaft furnaces.The demand for DR pellets has been increasing during the last few years and is believed to continue so in the future. Wanting to be present in this growing market QCM found that it would be essential to work at improving its DR pellets quality. Efforts have been focused on improvements in three areas: SiO2 reduction, elimination of sticking and increasing reducibility. Improvement programs have begun with laboratory research followed by plant trials and full-scale implementation as a cooperative effort among QCM, COREM, and key customers."

Jan 1, 2002

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018

By John Clancy, Andrew J. Freyman

"Trends in world coal markets indicate that the next twenty years could be a period of intensive development for British Columbia's coal resource. This paper examines demand projections for metallurgical, thermal and chemical feedstock coals, with particular reference to domestic and Pacific Rim markets. Supply possibilities, from the point of view of British Columbia's competitive position, are explored, with emphasis on the interaction of such factors as capital, labour, port and transportation requirements.The paper concludes with an examination of British Columbia's strategies in light of the foregoing, and comments on the government's role in ensuring that development of the coal resource be attained in a manner consistent with over-all provincial goals and objectives.IntroductionFor the purposes of this paper the Pacific Rim is defined as including, in addition to Canada, the following: Japan, Korea, the People 's Republic of China, Hong Kong, Taiwan, the countries of the Indonesian Archipelago, Australia, New Zealand and the Pacific-bordering countries of South America and Mexico. The United States has been excluded in this definition in order to better illustrate the economic growth potential for British Columbia coal in the Pacific Rim economies.In the past decade, the Pacific Rim economies have grown faster than most other economies in the rest of the world; economic growth rates of 10 per cent were common in the region prior to the 1974 slowdown and the average rate of economic expansion in the mid-1970s has exceeded 6 per cent. Rapid expansion of international trade in the region has been a major stimulus in this process. By 1979, Pacific Rim two-way trade has reached an estimated $550 billion-about 20 per cent of world trade."

Jan 1, 1982

By B. K. Mishra, Avijit Biswal, B. C. Tripathy, Abhijeet Singh, K. Sanjay, T. Subbaiah

We studied theeffect of anode substrates such as pure lead (Pb), lead antimony (Pb-Sb), and lead-silver (Pb-Ag) on the structural and electrochemical properties of electrolytic manganese dioxide (EMD). X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and chemical analyses were used to determine the structural and chemical characteristics of the EMD samples. The charge-discharge profile was studied in 9 M KOH using a galvanostatic charge-discharge unit. In all the substrates the current efficiencies were more than 99% except with Pb-Sb where it was 90%. Results revealed the nature of the substrate strongly affected the morphology of the deposited material which in turn affected the electrochemical properties of the EMD samples. XRD analyses revealed that the nature of the anode did not affect the crystal structure of the deposited EMD and all the samples were predominantly ?-MnO2, which is electrochemically active for energy storage applications. The EMD deposited on lead substrate showed superior discharge capacity of 245 mAhg-1 when compared with other substrates.

Jan 1, 2014

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016

By Niels Verbaan, Ernesto Bourricaudy, Ronald Molnar, James Brown, Sunil Jayasekera

"SGS Minerals commissioned an internal R&D program to develop in-house expertise to design, set up and operate REE separation pilot campaigns at its Lakefield, Canada site. A team approach was used that included expert consultants in the field of REE separation as well as in-house expertise supported by the on-site Analytical Laboratories.A mini pilot scale SX circuit was designed and constructed consisting of several modular banks of 30 stages each. About 80 stages of mixer-settlers were used to separate Pr and Nd from La and Ce contained in a synthetic REE chloride stream simulating the raffinate from an initial La-Nd|Sm-Lu+Y separation.Two pilot campaigns were operated totalling 25 days of 24/7 operation with 99.4% plant availability in the final 20 day campaign. Purities of > 99.9% in the Pr-Nd strip liquor and > 99% in the La- Ce raffinate were achieved and simultaneously sustained in the second campaign for prolonged operating periods. Key to controlling and adjusting the circuit was the rapid assay turnaround (as low as 2 hours) provided by the on-site SGS analytical lab. This permitted the operating team to modify conditions and observe the effect of changes relatively quickly considering the large number of stages. A portable XRF analyser was also used to track evolving assay trends in the circuit. The small physical size of the circuit enabled longer operation with a limited amount of sample.This paper discusses the design of the circuit, operating conditions, some of the key operating factors and controls and results obtained.INTRODUCTIONSGS Minerals commissioned the design of and built a solvent extraction (SX) pilot plant for the separation of rare earth elements (REE). The plant consists of a battery of 120 mixer-settlers set up in a dedicated piloting facility.The purpose of the programme was to develop capabilities and in-house expertise in REE SX separation technology. The program aimed to establish operating procedures, sampling regimes, and analytical methodologies and protocols for this type of process/plant. A team comprised of SGS personnel and several external consultants with prior industrial and REE separation piloting experience was assembled to achieve these objectives."

Jan 1, 2016

By A. A. Iranzadeh

The performance of a tunnel boring machine (TBM) depends on the efficiency of the cutters, which can be influenced by geological conditions and rock mass properties. In this study, a three-dimensional numerical model, based on a discrete element method, was used to evaluate the effects of joint orientation and its spacing on the fragmentation process by a TBM cutter. Several models were constructed to study the effects of variable orientation; these models incorporated different spacing, variable spacing, different orientations on the fragmentation process, and different sections of the block model. Three parameters, consisting of induced tensile stress, induced shear stress and maximum displacement, were calculated. The stress in each section that forms chips was considered as critical stress; critical joint spacing and orientation in each section were determined. Results show that the critical orientation was in the range of 45 to 60º, where there was a possibility to achieve the maximum penetration rate. The critical joint spacing was 200 mm and, by increasing joint spacing, the value of critical stress decreased significantly. Furthermore, joint orientation could influence more than joint spacing in the rock cutting process.

Jan 1, 2009

By J. J. Jonas, G. R. Stewart, A. M. Elwazri

Two important parameters for dynamic recrystallization can be derived from the changes in the strain hardening rate: the critical strain for initiation of dynamic recrystallization and the point of maximum softening. In this work, these values are determined from the flow stress-strain data obtained in continuous compression testing in the range 900-1100°C. The resulting strains are used to calculate a kinetic model of dynamic recrystallization for two materials: 304 austenitic stainless steel and a hypereutectoid plain carbon steel. The mechanical parameters used to define the proposed model are confirmed with quantitative metallographic analysis of the recrystallized microstructure.

Jan 1, 2004

By R. Lovat, J. A. Hunter

"The design, development, and verification of the Lovat 7.6metre diameter full-face tunnel-boring machine is reviewed. Programmatic and technical challenges are outlined with a review of the specifications and the design to meet these requirements. Subsystem designs are presented for the waste material removal, ventilation, cutter head, structural support, advance technique, water removal, and interfaces with the Donkin-Morien Mine. The techniques used to verify that the design meets the requirements is by testing in the Lovat factory and in the field. Certification of the machine for use in a methane environment is discussed.IntroductionStudies have concluded that the average annual worldwide tunnel construction is 500 kilometres at an estimated average co st of $3,400 U.S . per linear metre. The total market value of the tunnelling industry is estimated as approximately $1.7 billion U.S. per annum. Of this, the current market for tunnelboring machine excavation is approximately $270 million U.S. per annum worldwide with a further potential of $250 million if more contractors are convinced that Tunnel-Boring Machines (TBM) are more suitable than conventional techniques. The worldwide civil tunnelling market has the potential to double each year in the next 5 to 15 years. Growth has been identified in the energy and mineral resources sectors of the economies of many nations and a significant volume of machine tunnelling studies and trials are presently underway for the extraction of coal, uranium , heavy oil or oil sand fuels, metallic and non-metallic industrial minerals and base metal or rare earth ores. Further tunnel projects for regional transportation, waterpower, irrigation , high density urban transportation, storm water sewers and water supply purposes are continually being implemented with new concepts like military security facilities and underground storage schemes being considered.Lo vat Tunnel Equipment of Rexdale, Ontario, the only Canadian manufacturer of TBMs was incorporated in 1973 to manufacture so ft ground tunnel-boring machines to satisfy this growing market demand. Lovat has produced an average of 5 machines per annum during the period 1972 - 1982 and has established an international reputation for competitive costs, quality of construction, after-sales service, and reliability. As of June 1982 Lovat TBM's have been used to tunnel over 240 km in projects throughout the world."

Jan 1, 1984

By E. N. Gilje

"IntroductionDURING the past five years, over two miles of shaft sinking have been completed at Falconbridge. As sinking has continued, we have improved our equipment and technique with a resulting increase in efficiency. Throughout this period, all sinking has been done by contracting firms, under our direction and to our equipment specifications, with highly satisfactory results. Since 1949, Riddell shaft mucking machines have been successfully used in conjunction with the •benching method of sinking. Our most recent practice can best be illustrated by describing the method used in sinking No. 1 shaft at the Fecunis Lake mine.No. 1 Shaft, Fecunis Lake MineNo. 1 shaft, consisting of six compartments and measuring 13 ft. 11 l/2 in. by 19 ft. 9 3/8 in., outside timber (Figure 1), will be sunk to a depth of 4,170 feet. It was designed to accommodate two 10-ft.diam. Koepe hoists."

Jan 1, 1955

By Kevin Bell

About Beltek Inc. For more than a decade Beltek, Inc. has been working with national and international organizations to harness and deliver solutions which gain real ebusiness advantages in today's world. Our objectives are to partner with our customers to achieve maximum results, while reducing costs. At Beltek, we provide a commitment to you and your organization's needs. Whether that be delivered by ensuring our services and products are state of the art or by providing a level of personalized service, which makes you feel like the center of attention, Beltek is about adding value to every job we work on. The individuals who work at Beltek quickly become your friends because we share your passion and enthusiasm for the business we are in. That's why every person is a leader in his or her respective fields. Having these individuals as apart of our business ensures you get the best out of our equipment, receive the very latest in advise, problem solving and support. We also pride ourselves on our ability to remain flexible at all times because we know deadlines and schedules can change quickly, so we always go the extra mile to deliver exactly what you need.

May 1, 2004

By H. D. B. Wilson

THIS PAPER has resulted from a preliminary draft of a background paper prepared anonymously for the Science Council's Special Study of the Solid-Earth Sciences in Canada. The draft was circulated to eighty-four Canadian geologists; forty-eight of these responded with criticisms of the draft. All critical re-marks were considered carefully and most have been incorporated in the final paper in an attempt to balance the author's bias, although this bias undoubtedly still appears. Indications of support for a particular statement or section were also helpful, because many of these contradicted criticisms and enabled the author to judge the consensus. Thus, all criticism could not be incorporated because the referees did not agree. It is interesting that some remarks were con-sidered overstatements by some and too bland by others. The most perplexing critical comment was one which suggested a new author was needed, and went on to name the existing author as the most likely candidate.

Jan 1, 1970

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

By D. J. Houlahan

ABSTRACT Sorting has the potential to massively improve the pro?tability of mining base metal, hard-rock ores. However, several barriers to the increased application of sorting have been identi?ed, including a lack of mineral-speci?c sensors available to the industry. This paper presents the outcomes of acollaborative project to develop an induction-balance sensor speci?cally for low-grade copper and nickelores. A review of the basic principles of induction-balance sensing and of the sensor-rock interaction is presented. Early development and testing of the sensor on ores from the Thompson nickel belt in northern Manitoba is discussed. Shortcomings of the prototype identi?ed in early testing have now been over-come, leading to improvements in design and construction, as well as sensor accuracy. The improve dsensor has now been tested on additional ores from the Sudbury Basin, with good results. A discussion of potential applications is presented and recommendations for future development are made.

Jan 1, 2010

By W. B. Boggs

Part 1 Originally, the copper produced at the Noranda ?smelter was shipped in the form of blister bars to the Laurel Hill refinery of the Nichols Copper Co., New York. In 1930 a refinery was built at Montreal East for the purpose of refining Noranda copper and copper from the Hudson Bay Mining and Smelting Co., at Flin Flon. After investigation of the probable costs of making anodes at Noranda and at Montreal, it was decided to make them at Noranda rather than to continue to make blister bars there. Fuel is a major item of expense in making anodes: and since less fuel would be required in making anodes from molten copper than in making them from blister bars, a lower anode furnace cost could be expected at Noranda than at Montreal. Further, the expense connected with making blister bars at Noranda would be eliminated. The cost of treating anode and wire bar furnace slags is a serious item in a refinery, and it was found that the cheapest method would be to ship such slags back to Noranda. With the anode furnace at Noranda, much less anode furnace slag would be made at the refinery. Against these savings which would be effected by making anodes at Noranda must be set the high operating cost of an anode furnace at Montreal, using only tank-room scrap and the Flin Flon copper. This furnace would be handling a comparatively small tonnage and would have a high cost per ton. The usual equipment for making anodes from. liquid copper consists of either a stationary reverberatory furnace or a tilting Tacoma-type furnace together with an anode wheel of the Clark or Walker type. The reverberatory type of furnace has been developed from the furnace used in the old Welsh process of smelting and refining copper, while the tilting furnace is a development of the holding furnace, which is essentially a Peirce Smith converter without tuyeres and provided with burners.

Jan 1, 1932

By J. C. Gilbert

"IntroductionTHE PURPOSE of this paper is to discuss in a general way the heavy oil situation in Western Canada, and particularly to acquaint those in the oil industry who have not participated in the heavy oil end of the business with past and current developments. The author has covered •briefly the location of the heavy •and asphalt-base oil fields, their geology, current drilling and production practice, the location of the •refineries capable of handling heavy crude, their products and markets, and the problems and future prospects of the industry.Location and Description of FieldsThe term heavy oil is generally used to denote crude of 20.9° gravity and under. Since the products from heavy oil are also to a lesser extent obtained from asphalt-base crudes of higher gravity, some mention will be made here of the latter; but in general the emphasis of the paper is on heavy oil as such.In the order of their production to date, the heavy oil fields and those light oil fields which produce asphalt-base crudes are : Lloydminster, Taber, Vermilion, Conrad, Princess, and Wainwright.The Lloydminster oil field has not only produced most of the heavy oil, but also is currently the largest producer, supplying at the present time about 80 per cent of the heavy and asphalt-base crudes produced in Western Canada."

Jan 1, 1952

By F. C. Robles Hernandez

This paper presents the results of the electromagnetic semi-solid treatment of the 319 aluminum foundry alloy, Various levels of structure modification were achieved controlling the AC current used to create the Electromagnetic Field, thus manipulating the intensity of the field, The level of grain refinement, partial modification of the Al-Si eutectic, as well as cellular dendrites were observed, A quantitative analysis of the structure was performed using Image Analysis (IA) techniques. In addition a novel Thermal Analysis methodology was developed for the on-line determination of the microstructure modification level.

Jan 1, 2004

By Sunil S. Gandhi

Magmatic-hydrothermal deposits rich in magnetite and/or hematite form a broad group that includes monometallic Fe deposits and polymetallic (mainly Cu and Au) deposits. They show a considerable variation in deposit characteristics, but share the genetic processes of magmatic differentiation and related hydrothermal activity in intermediate to felsic melts, and in some cases involve brines and/or meteoric waters during mineralization. They include several world-class deposits. They range in age from Proterozoic to Recent, and form important metallogenic districts in Scandinavian, Canadian, Brazilian and Australian Shields, Circum-Pacific regions, and in China, Iran and Turkey. Monometallic deposits have been important sources of iron in the past and still contain significant resources of the metal, e.g., the Kiirunavaara deposit in Sweden. The giant Olympic Dam Cu-Au-Ag-U-REE deposit was discovered in 1975, and since then explorationists have focussed on search for analogues worldwide. This has brought to light a number of economically important new deposits and prospects, including examples in Canada. The discoveries have in turn prompted considerable research on individual deposits and the group as a whole. This short paper is an attempt to summarize the main aspects of the group from the literature cited in Gandhi and Bell (1996), and from the papers published recently in two milestone volumes on these deposits, edited by Porter (2000 and 2002).

May 1, 2003

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015