Search Documents

Knowledge of coalfield geology has evolved rapidly over the past few years. Recent advances ranging between exploration, mining geology and seam variation studies have enabled application of geological techniques commensurate with technological changes in the coal industry.

Jan 1, 1969

By N Fullelove

The Renison Bell Tin Mine on the West Coast of Tasmania has recently installed a new underground ore handling system incorporating underground crushing, conveying and hoisting facilities. Contracts for the sinking of the shaft and the development of the mine were let and managed by the operator, Renison Limited. Hardcastle & Richards was responsible for the design, procurement and construction management of the fixed plant and equipment including civil, structural, mechanical, electrical and instrumentation services. The system demonstrates worldÆs best practice in design and incorporates a state-of-the-art integrated control system allowing the entire system to be controlled by a single operator located in the underground crusher chamber. A rapid construction period was achieved, despite the difficult and constrained underground environment, without affecting the ongoing operations of the mine. The mine, which was established in the mid-1960s, had previously operated by trucking ore to the surface via a decline. Truck haulage distances and costs had increased as the mine became deeper over the years. By the 1990s it had become apparent that, in order to remain economically viable, it was necessary to reduce truck haulage distances and allow the mine to go still deeper to access orebodies such as Rendeep beneath the current workings. The Internal Shaft System achieved this by eliminating approximately 5 km of truck haulage. It allows the production rate to be increased to up to 1 Mtpa compared with a limit of 628 kt per annum by direct truck haulage to surface. The access it provides to the Rendeep ore and other deep orebodies greatly increases the amount of ore which can be economically mined.

Jan 1, 1998

This paper attempts to draw together the experience of over 30 years of research and practice in the United Kingdom on the rehabilitation of abandoned metalliferous mining wastes. The reliance on water when the mines were operating has implications for water quality and the techniques used to restore sites to alleviate the principal impacts of the mines. Drivers of reclamation included concerns about human health from wind blown dust and pollution of watercourses as well as perceptions of dereliction. Techniques of reclamation used involved removal of spoil from near to surface watercourses, capping of spoil, diversion of watercourses, use of impermeable membranes, prevention of surface sinks into underground workings and the use of constructed wetlands. The issues to be dealt with in mine reclamation have become more complex and sometimes diverge. The schemes in the 1990s described have been effective in dealing with pollution from spoil heaps and small but significant adit discharges; however, significant issues, particularly those of large flows of polluted water from mine sites, still need to be dealt with. Although the paper describes the legacy of mining, which largely finished in the late 19th/early 20th century, similar issues but on a larger scale are to be found in more recent mining, for example Eastern Europe. In many of these areas minerals still remain to be won and dealing with this legacy may fall on new mining developments.

Jan 1, 2006

By Weller KR, Lim IL

The high pressure grinding rolls is one of the few new comminution devices that offer substantial savings when compared with traditional crushing and grinding circuits and with SAG milling. The machine has been well accepted in the cement industry, but mining companies have been more cautious in adopting this technology, partly because of wear and availability problems, and partly because of uncertainties in designing circuits which will deliver the power savings without complicating downstream processing. This paper addresses the latter problem by providing a model structure for predicting power draft and throughput from measurements made with small pilot scale high pressure rolls. Three existing models for predicting product size distributions are assessed and suggestions made for future work. The model structure comprises a power equation, incorporating measurements of torque and rolls speed previously used by the authors. Transport through the mill is assumed to be plug flow. Throughput is governed by the equilibrium gap between the rolls, which is determined both by machine settings and the physical properties of the feed material, including its size distribution. Therefore some form of physical testing in a model machine is required to determine throughput parameters. Results from copper and nickel ore experiments covering a wide range of machine conditions are presented and compared with model predictions. Model assumptions are discussed and directions for future work Suggested.

Jan 1, 1993

HISTORY Up until the late 1880's the mining industry acquired a considerable proportion of its capital needs from domestic sources. Exchanges were established wherever major new fields were opened and Ballarat, Bendigo, Charters Towers, Coolgardie, Kalgoorlie and Silverton all boasted active trading in mining shares. For much of the first half of this century there was only modest developments in the mining industry and its capital require- ments were correspondingly lower. RECENT EXPERIENCE The new mines of the sixties were, in many cases, characterised by their remote situation and their output of bulk commodities such as iron ore., coal and bauxite. Infra- structure costs were particularly high and the level of capital expenditure was of previously unheard of proportions.

Jan 1, 1975

By M I. Pownceby, N Karimian, J R. Manuel, M J. Peterson

The CSIRO ore classification scheme for Pilbara ores was used as a reference frame to target recognisable ore types/textures with potentially elevated phosphorus content for detailed analysis. Particles of each individual ore texture were separated from a Brockman high-P ore and each class was characterised using methods including XRF, XRD, EPMA and synchrotron-based XAS. Results were then correlated with optical microscopy and hand specimen identification to establish any relevant associated mineralogical phases and/or textures. This represents a more systematic approach to identification of high-P ore components based on particle and goethite type and texture. The information can then provide the basis for more targeted P-removal strategies factoring in the relationship between particle/ore texture and phosphorus deportment

Sep 18, 2023

By G Johnson, S Michalek, N Redman

As the modification of the 2009 Mill OperatorsÆ Conference theme from æmilling through the boomÆ to æthe boom û experience gained and lessons learnedÆ exemplifies, comminution practitioners are facing a series of challenges in the dramatically changing mining environment. One of the main problems plant managers have been facing during the boom times has been the severe metallurgy skills shortage and high staff turnover, both factors that can cause difficulties in mill liner management. Many of todayÆs mill managers are now also more than ever faced with the need for cost-cutting in order to continue operating viably. Amongst other potential target outcomes such as maximised throughput, MillMapperÖ, a tool for mill condition monitoring and mill performance optimisation, can be utilised to address these issues. This paper demonstrates how MillMapperÆs quantifying decision making tools can serve to be in control of managing mill liner and production issues, and how it can form the basis for mill cost savings without the risks normally associated with conventional methods or the lack of using any condition monitoring methods. MillMapperÖ is currently being referred to at a rate of approximately 150 surveys and associated reports per annum at processing plants in Australasia, South America and Africa. Examples throughout the paper provide insight into how the presented sample set of users have extracted benefits that could have otherwise not been safely or at all achieved.

Jan 1, 2009

By R M. Briggs, I E. Smith, P M. Black, A B, R L. Brathwaite, J L. Mauk

The Hauraki Volcanic Region of the North Island developed between 18 and 1.9 Ma. Initial andesitic volcanism from 18 to 12 Ma was followed by 12 to 1.9 Ma volcanic activity that included rhyolitic, dacitic, andesitic, and basaltic compositions, with a gradual migration of activity to the SSE. Early andesitic volcanism evolved over the course of 8 m.y. to more silicic compositions; this trend was reset and repeated by post-10 Ma andesitic volcanism. Early and later andesites are otherwise remarkably similar in trace element composition. Rhyolites have the most diverse compositions, suggesting a major role for crustal input in their formation.

Jan 1, 2007

By K J. McDonald

All commercially available zircon sands contain radioactivity sourcing from the decay of trace amounts of contained uranium (U) and thorium (Th). The fine particle size zircons of the Horsham area in the Murray Basin region of Victoria, Australia, contain significantly more (about twice) Th+U than those commercial zircon sands. The marketability of these fine-grained zircon sands is likely to rely on the removal of these radioactive impurities. CSIRO Minerals have been working for some time to develop processes for the removal of the radioactive impurities from zircon. It is generally agreed that it is quite impossible to leach U and Th from zircon, however, the Heat and Leach (HL) process, described in detail in Aral and McDonald (1999), reduces the radionuclide levels significantly. The identified (HL) process aims to leach uranium and thorium selectively from a decomposed zircon. The novelty of the process is that a large part of the leached product can be reconstituted to a low radiation zircon by a subsequent heat treatment. The HL process uses a flux mixture of sodium carbonate and calcium borate to decompose the zircon at relatively low temperatures (900 to 1150¦C) and a weak acid (0.5M HNO3; 80¦C/0.5 h; pulp density ten per cent) to leach the radionuclides selectively. The process leaves the major components (ZrO2 and SiO2) behind with little loss. The HL process for example lowers the U+Th content of a Murray Basin zircon from 1000 ppm to 400 ppm U+Th. Among the radionuclides more U progeny is removed than the Th series radionuclides. This is very significant as the radioactivity of U series is 2.5 times more that from the Th series. Therefore the reduction in the radioactivity level of zircon is more than the reduction in Th+U indicated by XRF analysis. A schematic flow sheet of the HL process is shown in Figure 1. Although the HL process successfully lowers the radionuclide levels in zircon sands, the final product contains significant amounts of sodium (up to 14 per cent Na2O) and small amounts of CaO. By comparison, the sodium content of the commercial zircon sands is in general 2O. Zircon is used mainly as an opacifier in tile glazing where the addition of ten to 15 per cent zircon to a translucent base glaze gives the sanitary white colour to the tile surface. Opacification is the result of the refractoriness of zircon particles at the glaze firing temperatures that is generally around 1050¦C.

Jan 1, 2001

By Han Kook-Nam, Lawson F

The recoveries of the three cobalt minerals in the Mount Cobalt deposit, cobaltite CoAsS, erythrite CO3(AS04)8H20, and new cobalt mineral with a composition approximating 2CoO.CaO.Fe203.2As205.11H2O were investigated using physical and surface-chemical processes.Over 80 per cent cobalt recovery was achieved by tabling a cobaltite-mineralized sample, while about 76 per cent cobalt recovery was obtained by dry feed magnetic separation of a sample containing erythrite and the new cobalt mineral. The resultant primary magnetic concentrate with a cobalt grade of 5.5 per cent, was able to be upgraded to 14.4 per cent cobalt by regrinding .and a further magnetic separation.Electrophoretic mobility - pH responses for each of the three cobalt minerals were found to be similar. Each mineral remained negative over the pH range 3 to 11 and was most negative at mildly alkaline pH values.Cobaltite was floated effectively with amyl and ethyl xanthate collectors under acidic conditions at collector concentrations of 10-2M to 10-5M. Erythrite showed a similar flotation response using 10-sM amyl xanthate. The practical application of these laboratory separations to an industrial process is suggested.

Jan 1, 1976

The stratigraphy of the Singleton Coal Measures is reviewed and a revised stratigrapixy which has been ratified by the N.S.W. Standing Committee for Coalfield geology is nominated and defined by a selected type section. Withir the type section the occurrence of repetitive phases are illustrated and described. Coal. Measure units within the Singleton Coal Mean sures, termed the Wollombi and Wittingham Coal Measures respectively, are correlated with the Newcastle and Tomago Coal Measures. In formal nomenclature the Singleton Coal Measures are designated the Singleton Super Group. The major depositional cycles within the Coal Mea- sures are outlined together with those lesser phases within the Coal bearing sequences that influence the mining conditions likely to be encountered. Both tectonic and sedimentary features of the Singleton Coal Measures are considered and the localized post depositional effects on the coal seams and roof strata in- duced by differential, compactions are emphar Sized.

Jan 1, 1972

The Elgas Underground Storage Facility at Port Botany, Sydney, is the first purpose-built cavern of its kind in Australia and provides large capacity, safe and environmentally benign storage of Liquefied Petroleum Gas (LPG). The facility will provide Elgas with the flexibility to source product at competitive prices and ensure long-term security of supply. Construction has provided Orica Australia, formerly ICI Explosives, with a unique opportunity to provide a bulk explosive delivery system specifically designed to meet the exacting demands of the site and of the project.

Jan 1, 1999

By McMahon DW

The major components of a mineral reserve estimate for project development purposes are described with respect to sampling, geology, estimation methods, mining factors, metallurgical factors, environmental factors, financial and other factors. Each of these components impact to varying degrees on the recoverable metal or product of a new mining project. The evaluation of a project is a complex process involving the best the profession can provide in terms of geological understanding, engineering ingenuity, metallurgical skills and financial evaluation.

Jan 1, 1983

With constantly rising energy costs it is ever more important that we look at ways of im- proving comminution efficiency both in terms of power consumed as well as capital costs required for purchasing and installing equipment. I intend to show that commonly used appli- cation criteria, which is presently accepted for designing crushing and screening plants, need drastic revision if it is to be used to accura- tely design, predict and refine performance in new and existing facilities. Unless we can calculate performance accurately, we cannot minimise capital investment and maximize Profitability.

Jan 1, 1978

By Hayes J. A

The satisfactory ventilation of an extensive coal mine is a subject which requires continual attention from all concerned.It must be remembered that a colliery contains many miles of workings, extending in all directions and throughout which noxious gases may be given off either naturally or by oxidation of the coal; fumes from explosives will be produced, dust will be gathered and carried in suspension, and water will be evaporated, producing a high humidity. Hence a considerable quantity of air in movement must be available to provide sufficient oxygen for men and horses, as well as to dilute and sweep away impurities, and maintain a tolerable degree of coolness.To maintain these conditions a modern colliery is divided up from the main ventilation shafts or adits (as the case may be) into a system of main airways, and in the working districts is further subdivided into district splits. To initiate the air movement, large centrifugal fans with a displacement capacity of up to 400,000 cu. ft. of air per minute are installed, generally in drifts off the upcast shaft, or adit, and at the return end of the ventilating circuit. These fans are thus exhausting fans and by producing a region of low density bring the heavier air at the other extremity of the circuit into movement to correct the difference in density, so far as it is not prevented by the frictional resistance of the airways. A flow of air is thus established, and it is obvious that to enable this volume of air to be as great as possible, the frictional resistance of the mine airways should be maintained at the lowest practicable figure. To this end, main airways should be as large as possible, have sides as smooth as practicable, and be straight, any necessary bends being of large radius.REQUIREMENTS OF THE VENTILATION SYSTEMThe New South Wales Coal Mines Regulation Act contains stringent provisions on requirements of the ventilation system. The main points are expressed in the following extracts:"In every mine which is in operation, unless a certificate of exemption from compliance with this rule has been granted by the Minister, whether any person employed therein shall be...

Jan 1, 1947

By B, J Bianchini, N Voermann, C Crowe

Operational and economic imperatives in the metallurgical industry have led to numerous advancements in furnace design. Modern furnaces provide high production rates, high percentage online time, long campaign life between rebuilds and safe operating conditions. Current trends for maximising plant efficiency include increasing the throughput of existing process vessels (often by a factor of two or more) and the use of newer, highly intense processes. In both instances, the process intensity results in the generation of higher heat fluxes to the crucible walls. High-intensity furnace operation with the objectives mentioned above has become possible with the following furnace design features: Strong sidewall cooling systems, using copper coolers, to accommodate the high heat fluxes encountered while protecting the crucible refractories; Robust, spring-loaded furnace horizontal and vertical binding systems which maintain tight brick joints through-out all stages of operation; and Well-designed, intensely cooled tapholes for metal, matte and slag. The integration of these features along with properly selected refractories, appropriate instrumentation systems and efficient water-cooling systems is also highly critical. These design features have been successfully implemented in electric smelting furnaces, flash smelting and converting furnaces (Outokumpu and INCO types) and lance injection furnaces (Mitsubishi, Ausmelt and Isasmelt types). This paper will discuss design aspects and operating results for several installations.

Jan 1, 2002

WaihiÆs Cornish Pumphouse is located on the edge of town in a dynamic and changeable area where history affects the future. As in any successful project, ingenuity and team work have been significant factors in the planning and implementation of the buildingÆs relocation.   Work around the Pumphouse site commenced circa 1900 with preparation to sink the No 5 shaft. Construction of the pumphouse and the steam driven C pump was completed by 1904 with hints of what was to come evident in 1905 as the No5 Shaft collar had sunk 350mm in four years. By 1907 surface cracking developed over the Milking Cow cave area and in 1913 200 mm was cut off the main pumping rod as the ground was sinking at a rate of 25 mm per year.   In 1913 ground around No 6 shaft had subsided 600 mm.It was also the end of an era as steam gave way to hydroelectricity and electric pumps replaced the C Pump. C Pump was maintained as a backup from 1913 to 1929 and then finally scrapped. 25 years of underground caving operations removed approximately 400 000 cubic metres of ore leaving a 7 ha collapse crater that eventually became known as the mine lake.   On the edge of town a tension zone over the Royal Lode began to develop 50 m diameter chimney collapses as large scale blocks relaxed into unfilled stopes in the old Martha underground mine. After the 1999 collapse part of the main street was closed and after the 2001 collapse Hazard Zones were declared, more streets closed and areas evacuated and retired from residential use.   By 1984 the Pumphouse has approximately one degree of tilt and in 2002 tilt on the Pumphouse accelerated briefly and then settled down. Tilt accelerated again late in 2004 and a scoping study was initiated to define protection options for the pumphouse. The Martha Mining Licence requires Newmont to 'Take whatever precautions are necessary to protect the old Cornish Pumphouse adjacent to No5 shaft' and viable solutions needed to found.   Any work on the Pumphouse comes standard with a wide range of stakeholders, governing agencies and legal framework to consider. Land Information New Zealand (LINZ) is owner and administrator of the pumphouse.

Jan 1, 2006

Between, 1980 and 1984, the demand for non- ferrous metals in the free world grew annually by 1.5 per cent for copper, 0.4 per cent for lead, 1.4 per cent for zinc, and 2.5 per cent for nickel. The growth rate decreased substantially compared to the rate experienced before 1980, and was far lower than the GNP growth during the corresponding period. The main reasons for this are considered to be 1. resource-saving efforts by industrialized countries resulting from the first and the second oil crises, 2. saturated demand for durable consumer goods, and 3. substitution of non-ferrous metals by new materials such as optical fibers.

Jan 1, 1986

The demand for minerals will grow strongly to satisfy the needs of an increasing world population for materials and energy. The technical problems involved in producing these minerals will be daunting and the engineers who will have the responsibility for designing and controlling the mineral production processes must have a high level of skills. This will place a heavy responsibility on the education system. A small number of large, well equipped university departments dedicated to mineral processing and having a close working relationship with the mineral industry, and an international orientation, will be much better placed to meet the needs than a large number of small ill-equipped departments which find it difficult to remain viable in modem universities. Courses in mineral processing must be designed to meet the scientific and technological needs of industry and full use must be made of innovative educational techniques such as video conferencing in delivering the courses. The concept of a major international network of major mineral processing departments which is designed to make best use of scarce academic resources is important and should be considered by the International Committee of the IMPC.

Jan 1, 1993

By F Melcher, M Wiedicke, A Wittenberg

Ferromanganese nodules form a specific category of widespread marine mineral deposits. The tremendous increase in metal prices during the last decade raised new economic interest in their exploration. The German Federal Institute for Geosciences and Natural Resources (BGR), which had been engaged in nodule research in the 1970s and 1980s, renewed its activities on this subject based on an exploration contract with the International Seabed Authority, signed in 2006. BGRÆs licence area û comprising 75 000 km2 û is located between the Clarion and the Clipperton Fracture Zones. In this so-called nodule belt north of the equator the sea floor reaches water depths of >4000 m. About 900 million tonnes of manganese nodules are expected there. In this study the fine-scale distribution of important elements in manganese nodules and crusts from a variety of locations was investigated. Besides 11 samples from the RV SONNE cruise SO-25, numerous samples from additional locations were included in this study for comparison. In general, the sample suite includes two genetic types of precipitates, manganese nodules and Co-rich crusts. A detailed characterisation of the distribution of major, minor and important trace elements in manganese nodules based on in situ microenergy dispersive X-ray fluorescence (¦-EDXRF) analysis is presented here. The data are compared with bulk major, minor and trace element data as well as with quantitative electron probe microanalysis (EMPA) data sets. The element distribution maps and profiles produced by ¦-EDXRF analysis with short or extended (in case of profiles) counting times, allow precise selection of æregions of interestÆ for further detailed investigation using high spatial resolution techniques (eg scanning electron microscope (SEM)-EDAX; laser ablation-inductively coupled plasma mass spectroscopy (LA-ICPMS); isotopic studies).

Jan 1, 2008