Search Documents

Better quality at lower cost is today's formula for remaining competitive in a world market. For an integrated steel company, high quality low cost steel production must originate before the blast furnace. In 1979, when U.S. Steel initiated a Quality Management Program throughout its steelmaking operations, efforts began at the coal, ore and flux mines. The objective was to improve the quality and reduce the variability of the critical parameters for steelmaking raw materials, to get the blast furnaces, and subsequently the melt shops, under optimum control. The general details of U.S. Steel's Quality Management Program are discussed and how it was used to promote the desired improvements in steelmaking raw materials. Some of the outstanding results obtained by the cooperative efforts between the mines and the steel plants are reported. The lessons learned by U.S. Steel were through upgrading existing operations and facilities. These principles should now be applied to new projects and the benefits of good quality management should commence from the time new projects are Commissioned.

Jan 1, 1986

By M Xu and, P F. Wells, A N. Kerr, Y Shields

Triethylene tetramine (TETA) has been used in combination with sodium sulfite (sulfite) for pyrrhotite depression at Clarabelle Mill since 1998. This combination has been highly successful at reducing pyrrhotite levels in the bulk (Ni/Cu) concentrate. Although highly effective, the roles of TETA and sulfite are not well understood. Treating bulk samples of the circuit feeds through the miniplant enabled the effects of circuit configuration on the performance of the pyrrhotite rejection circuits at Clarabelle to be determined. Reasons for the different performance of the non-magnetic pyrrhotite rejection circuit in the miniplant were investigated and tested in the laboratory. The effect of different grinding environments in the laboratory was examined to better understand the depressing mechanisms of TETA/sulfite. Modification of the grinding chemistry improved the selectivity of pentlandite over pyrrhotite in the presence of TETA/sulfite at current plant dosages.

Jan 1, 2005

By Dorricott M. G, McAllister J

This paper is concerned with the application of a probabilistic approach to the risk assessment of mining projects.In current practice, sensitivity analysis is the most commonly used deterministic approach of accounting for the uncertainties involved in mining project evaluation, while Monte Carlo simulation is considered to be the best probabilistic method available for the same purpose. The methodology of the approach proposed in this paper is as simple as that of sensitivity analysis. However, the results obtained can be more comprehensive than those obtained from Monte Carlo simulation. Various important statistical features, such as correlation and skewness, of the basic random parameters can be easily taken into account by the proposed approach. Example studies are demonstrated. Lotus 123 was employed for the associated probabilistic calculations.

Jan 1, 1992

By I R. F MacCulloch

Bacterial oxidation of sulfide minerals is a familiar and commercially available process to enhance gold recovery with problem ores. Pintail Systems, a Colorado, USA based company had developed bio-processes for gold recovery based on natural mineral formation and transformation in a global mineral cycle. The biological recovery of precious metals from ore involves a number of mechanisms that are dependent on the metal-mineralogical association. These processes include: partial bio-oxidation of sulfide ores; oxidation of gangue minerals exposing gold to leaching; surfactant properties of bacteria/nutrient solutions that improve wettability of ores and solution contact with leachable gold and silver; and microbial production and excretion of trace amounts of gold lixiviants, and bio-fracturing or biological alteration of ore minerals. Pintail has demonstrated enhanced recovery of precious metals during cyanide detoxification of spent heaps at the end of mine life. Biological recovery processes also have the potential to be applied to in situ mining technologies. The in situ process application could recover gold from subgrade deposits, small deposits or those ore bodies with uneconomic stripping ratios for conventional mining. In situ biomining can be accomplished at a fraction of the cost of conventional mining and leaching and does not have the environmental liabilities associated with many conventional gold lixiviants.

Jan 1, 2004

By Dyson NF

Nickel sulphide precipitated from waste liquors at the Yabulu plant of Queensland Nickel Pty Ltd was pressure leached under various conditions. Leaching at 130¦C and 700 kPa of air dissolved 95 per cent of the nickel as the sulphate in less than 2 h. Leaching at 130¦C and 350 kPa of oxygen dis- solved 95 per cent of the nickel in less than 1 h. Dissolution was faster with oxygen than with the equivalent pressure of air. Crystallization of hydrated nickel sul- phate from the resulting clarified leachate is readily achieved. Because the sulphide pre- cipitate also contains minor amounts of iron, copper and cobalt, the crystallization product contains these metals in excess of the amounts required for electrolytic-grade nickel sul- phate. This grade of product could only be produced if the contaminants were removed prior to crystallization. Alternatively, the "crude" nickel sulphate could find a market as a feed for the electrolytic production of Ni-Fe coatings.

Jan 1, 1984

By K Esmaeili, S Aziznejad

Impact-induced rock fragmentation is a mechanism that is commonly used for rock breakage in drilling and crushing. Additionally, rock fragmentation by blasting is frequently used in rock excavation operations. Experience shows that the presence of discontinuities can significantly influence the impact-induced damage and fragmentation of rock. Quantification of the response of jointed rock masses to impact loads is complicated by the fact that the available laboratory tests are mainly designed for aggregates or intact rocks. It can be argued that neither of these tests adequately represent a jointed rock mass. This paper presents the results of a series of numerical simulations used to investigate the influence of pre-existing discontinuities on the impact-induced fragmentation of rock masses. The methodology includes determination of the static and dynamic mechanical properties of a rock unit by conducting a series of laboratory tests on intact rock samples collected from a quarry in Canada. A 2D distinct element code, Particle Flow Code, was used to generate a bonded particle model in order to simulate both static mechanical properties (uniaxial compressive strength, elastic modulus, Poisson’s ratio and indirect tensile strength) and dynamic mechanical property (drop weight tensile strength) of the intact rock. The calibrated numerical model was then used to construct large-scale synthetic rock mass samples by incorporating discontinuity networks of different intensity into the bonded particle model. Finally, the impact-induced fragmentation inflicted by a rigid projectile particle on the jointed rock mass samples, simulated by a synthetic rock mass model, was determined. More fragmentation was observed for the rock mass samples with higher joint intensity.CITATION:Aziznejad, S and Esmaeili, K, 2015. Effects of joint intensity on rock fragmentation by impact, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Ostrea AM

Aqueous oxidation in an autoclave at ele- vated temperatures and oxygen partial pres- sures is applied to Philippine gold-bearing sulfide ores and concentrates which respond poorly to conventional cyanidation. The gold concentrates are recovered from ores and tail- ings material using the patented OMLI Process (the OMLI Process is able to upgrade tailings material analyzing 0.50 g/t Au to a concen- trate with a grade of 5 g/t Au or better). The results show that with aqueous pre- oxidation of the concentrates ahead of cyani- dation a four-fold increase in gold recovery is obtained compared with straight cyanida- tion. The observed differences in response to the pre-treatment step between various mate- rials are correlated with their mineralogical composition. The chemistry of aqueous oxida- tion is also presented.

Jan 1, 1986

The high cost of sampling systems is largely due to the fact that indiv- idual mechanical type sampling units must be installed at the discharge end of ore/pulp pipelines, that is, at points where the pipeline discharges into pump sumps or the like. A considerable economic advantage may be obtained in the use of a samp- ling device that can be installed at any point in the path of the trans- porting pipe line. Initial tests on a vertical line with an injection sampler using iron ore concentrates reveal the validity of this type sample versus that taken with a mechanical sampler. A descrip- tion of the injection sampler shows its simplicity of installation, requir- ing minimum downtime on existing lines.

Jan 1, 1976

By M A. Harrington-Baker, J M. Trudnowski

Sulfate-reducing bacteria (SRB) have the ability to immobilise dissolved metals by precipitating them as sulfides, provided that a favourable biochemical environment is created. Such an environment includes the presence of sulfate, anaerobic conditions and the availability of organic carbon. If such conditions are engineered within a reactive barrier or field-bioreactor, most metals can be effectively removed. To demonstrate this concept, three passive SRB field-bioreactors were constructed in 1998 at an abandoned mine site in the vicinity of Butte, Montana, USA to treat acid mine drainage with characteristic elevated concentration of metals and low pH. Performance of the field-bioreactors, using aqueous samples, was monitored over 32 months until the project was terminated, field-bioreactors were decommissioned and solid matrix sampling of the reactive matter was performed. The most important analytical results are presented in this paper together with conclusions regarding the appropriateness of the field-bioreactors construction features. Only Zn, Cu, and Cd were being removed as sulfides due to SRB activities. Changes in concentrations of other metals (Fe, Mn, Al, As), which do not necessarily precipitate as sulfide, seemed to be affected by SRB only in an indirect manner by responding to increased pH caused by SRB activity. An innovative cellular containment system used for placing organic matter worked very well in preventing settling of the organic matter and ensuring uniform flow of AMD throughout the entire cross-section of the organic carbon with no preferential flow paths This demonstration was funded by the US EPA and was jointly administered by the EPA and the US DOE under DOE contract number DE-AC22-96EW96405. The project was implemented by MSE Technology Applications, Inc, Butte, Montana, USA.

Jan 1, 2003

By M E. Trim, J J. Johnson, W Cranston

The Brightwater conveyance system is located near Seattle, Washington in the north-western United States. The East Contract portion of the system consists of a 4.3 km long, 5.9 m diameter tunnel in soft ground and two large shafts constructed in challenging soil conditions. The two shafts are situated side-by-side in an urban valley. One will house an influent structure to direct incoming sewage and outgoing treated effluent, while the other will house a 645 megalitre per day (ML/d) influent pump station. The tunnel contains four pipelines: two force mains to convey untreated wastewater eastward from the new pump station to a new treatment plant, one gravity-pressure pipeline to convey treated effluent westward to a new outfall in Puget Sound, and one high-pressure pipeline to convey reclaimed water from the treatment plant to downstream distribution points. The shafts and the tunnel presented many design challenges. Groundwater is near the surface in the area surrounding the shafts, and compressible peat and clay soils preclude dewatering during construction. These and other challenges were encountered during design of the pump station shaft and multiple-pipe tunnel. The challenges were addressed by a design that includes a dual intersecting circular cell shaft (referred to as æthe peanutÆ) and a single tunnel into which stacked pipes will be æstuffedÆ. This paper discusses the design approach and design details for both elements.

Jan 1, 2008

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

By H Bleuler

A new portal and access drift was constructed by Concrete Constructions for BHPÆs Elouera Colliery, south of Wollongong.The portal area at the base of the Illawarra Escarpment is in soft colluvium material, underlain by highly to moderately weathered sandstone. The area has a well documented history of slope movement or slope creep and one of the main criteria for the design was to minimise disturbance to the unstable slope by limiting the excavation for the portal establishment. This was achieved by incorporating a sloped headwall and gabion wingwalls to accommodate the anticipated creep and groundwater seepage.Main features of the design process also included the provision of both primary and secondary support in a single shell application and the use of canopy tubes to provide support ahead of the tunnel face.The active involvement of the designer during the construction phase and the flexibility of the design concept allowed changes to the support methodology to be carried out as excavation proceeded.This paper describes the design process undertaken for portal establishment and access drift to cater for the variability of the exposed ground conditions along the drift alignment.

Jan 1, 1999

By N Eriksson

BolidenÆs Aitik mine, located 100 km north of the Arctic Circle in northern Sweden, is one of EuropeÆs largest copper mines. This operation produces 18 Mt of ore per year and 99 per cent of this tonnage needs to be deposited as tailings. The tailings pond currently covers 1140 ha but at closure it will hold around 760 Mt of tailings and occupy an area of 1400 ha. The tailings contain less than one per cent sulfur and only 0.03 per cent copper. The carbonate content is as low as 0.25 per cent but silicates, with substantial accumulated buffering and metal adsorption capacity, are abundant. A programme of comprehensive material characterisation and investigations has been undertaken in order to design a decommissioning strategy that meets the regulatory requirements and secures long-term physical and chemical stability of the deposited tailings. The main concern has been the potential generation of acid rock drainage (ARD). Standard tests using acid base accounting (ABA) and humidity cell tests during 15 weeks were not conclusive regarding the ARD generation potential. The accuracy of the results was considered to be unsatisfactory, therefore the humidity cell tests were gradually extended in time. In total, almost four years of humidity cell tests were conducted on various sets of samples which were selected in order to cover the variation in sulfide content existing on site and in various points of the milling process. The laboratory results were subject to detailed geochemical evaluation in order to fully understand the interaction between acid-producing reactions, driven by weathering of sulfides, and acid-consuming reactions by dissolution of carbonates and alumino-silicates. The laboratory tests were followed by both pilot tests and field measurements in order to estimate the scale dependency between the laboratory and the field results. It was found that sulfide weathering rates in the field were considerably lower than those measured in the laboratory. However, it could not be verified that the tailings top layer would maintain a neutral pH in the long term even under field conditions. Thus, a reviewed tailings management plan, including de-pyritisation of the tailings during the last years of operation, is considered.

Jan 1, 2003

ABSTRACT' The first references to gold in New Guinea were by the Portuguese in 1525. The first significant discovery and gold rush was on Sudest Island in 1888 and was a natural extension of the rush that surged up Australia's eastern coast and ended at cook- town. Prospectors made a series of minor discoveries in coastal regions before the first large discovery at Wau/Edie Creek/Bulolo in 1925. Major post war gold discoveries were made at Bougainville, Frieda River, Porgera and Ok Tedi. On Misima Island a large bulk low grade deposit has been recognised surrounding old gold workings. Gold exploration has increased drama- tically since the lifting of a 3 year moritorium on new exploration areas in Noverrber 1982. A new bulk low grade gold discovery has been made on Lihir Island, north of Bougainville and a number of other promising areas are being drilled. Gold production is also expanding dramatically from current levels of 600,000 ounces to an anticipated 1.3 million ounces in 1985 with the opening of Ok Tedi. Other potential developments are likely to increase output above 2 million ounces by 1990. Papua New Guinea's world ranking as a producer is likely to move from 9th to 7th in 1985 reflecting the favourable geological potential, stable political environment and attractive development terms offered by the Government.

Jan 1, 1984

The high maintenance of load-haul-dumps (LHDs) and front end loaders in hard rock affects mine planning with reduced availability and productivity. Intensive study of maintenance costs and availability of machines related to machine age and life provide the basis for planning from available operational alternatives.Derived programmes and experiences have led to the beginnings of unmanned operation and automation through reduction of manual diesel units and spreading electrification and use of radio. But electrification has obvious layout limitations. This approach to the present has resulted in better utilisation, costs and safety and the computerised monitoring and control provides continuous awareness of machine and work conditions with the promise of future improvements.

Jan 1, 1991

By S Basu, S L. A Gowravaram

CaF2 has been a common constituent in a wide variety of welding fluxes, including those used for submerged arc welding (SAW). The widespread use of CaF2 stems from its role in lowering the liquidus temperature as well as the viscosity of the molten slag that covers the weld pool. However, the harmful effect of fluoride evaporation from molten flux, on the environment as well as the health of the users is becoming increasingly evident over the years. This has led to increasing attention towards reducing the CaF2 concentration in the fluxes. The fluoride-free formulations face the challenging requirement to maintain the thermo-physical properties (viscosity, liquidus temperature etc) like those observed in fluoride-containing fluxes. In the present work, three fluxes with compositions in the CaO-MnO-SiO2-Al2O3 system have been identified as promising alternatives to the CaF2-rich fluxes. However, the thermo-physical properties of any such flux need to be comparable to CaF2-based commercial SAW fluxes before it can be adopted for regular use. The single hot thermocouple technique (SHTT) has been used by several researchers in the past as a tool for observing the melting and solidification characteristics of fluxes. This device has been developed in the present work and is used to characterise the melting behaviour of the fluxes. The measured solidus and liquidus temperatures from SHTT were compared with the results from differential thermal analysis (DTA) and simulations using the FactSage™ software for a comprehensive understanding. In spite of having a slight deviation in the measured values from the multiple techniques, the results obtained from these multiple methods show that the selected compositions could be potential CaF2 free alternative welding fluxes.

Jun 19, 2024

By Gyasi-Agyei Y

In recent years rapid advances have been made in the technology used for hydrology and erosion modelling of rural catchments. These advances have been driven by the growing availability of digital terrain maps that can be used to automatically define catchment properties that previously had to be manually extracted from contour maps. In addition, these models have, in principle at least, more powerful predictive capability. The author is involved in a number of projects to migrate and further develop these models for application to mine rehabilitation assessment. Current technologies for hydrology and erosion assessment (eg CREAMS, ANSWERS) are reviewed, underlying principles highlighted and deficiencies in the context of mine rehabilitation design assessment addressed. The advantages and disadvantages of the new digital terrain map tools (eg WEPP, SIBERIA) are discussed. Current work integrating these new models with existing rehabilitation design tools (eg ACIRL's ARGUS computer package) highlights the advantages of an integrated approach using digital terrain maps; cheaper, faster, lower impact and more flexible rehabilitation design. The use of novel visualisation tools to aid the design process is discussed. The paper is illustrated by applications to mine sites in Queensland and the Northern Territory.

Jan 1, 1995

The Newmont Waihi Operations are centred on the Martha mine at Waihi, New Zealand. The mine has produced over 6.6 million ounces of gold from both openpit and underground sources since operations began in 1878. The current open pit operations commenced in 1988 and in the year to 30 June 2002 produced 129,790 ounces of gold at a cash cost of USD122 per ounce. This paper provides an overview of current operations and future directions.

Jan 1, 2002

By I Gipps

The mining industry has come through a period of major change in community expectations regarding safety and environmental impact and these changes can be expected to continue in the future. These changes are ultimately reflected in Government regulations and industry safety standards and form the basis of the ælicense to operateÆ. Equally, advances in technology have made possible new equipment and processes either available now, or close to completion, that will allow mines to meet these more stringent expectations if properly introduced. Changes in technology provide opportunities for mine management to introduce new systems that will remove people from hazardous areas and lead to improvements in the ætriple bottom lineÆ. In a longer time frame of five to ten years, novel and advanced technologies that are currently being developed will deliver new mining methods and conversion of presently uneconomic resources to ore. This is consistent with the time frame required to develop a new mine from discovery. Strategic decisions can be taken now by mine designers to enable the introduction of these major technology changes. Examples of both practical and strategic opportunities are drawn from the integration of rock cutting/blasting, automation, electronic communications and new mining methods. This paper discusses emerging industry trends, changes to legislative framework and some practical choices for existing and imminent technology.

Jan 1, 2003

In Mount Isa voltage and frequency fluctuations caused. by haulage shaft operation gave considerable difficulties with the initial application of Atomic Absorption Spectro-photometry.The methods used to stabilise the various units ' have been described.- Some other difficulties and the means used to eliminate or reduce them together with a-modified burner design are also discussed.

Jan 1, 1963