Search Documents

By Cleghorn JH

Underground mining operations on Kalgoorlie's Golden Mile were suspended in 1976, suffering the combined effects of low gold prices and grades. A subsequent substantial increase in the gold price led to the decision by Kalgoorlie Mining Associates to reopen their mines in 1979. The two shafts selected for access required excessive maintenance. The geological assessment and development parameters prescribed have been successfully used to establish reserves to maintain production at a 390 000 tonnes per annum rate. While ore reserve grade is being maintained from primary stoping sources, supplementary lower grade ore is drawn from remnant pillars and stopes at lower cost.Performance by the workforce has reached levels previously attained and a record tonnage was hoisted in the fourth year after recommencement.Keywords : Golden Mile lodes, geological research, payruns, cut and fill, mill holes, gold price, ore grade, amalgamation.

Jan 1, 1984

By Duncan GR

Having passed through a number of previous phases the best longwall results in Australia have shown a significant increase in the last two years. The results expected from a longwall face can be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the utilisation, and the available operating hours. Back analysis of the results achieved suggests that, on average, recent improvements arise from the higher capacity equipment recently installed; the utilisation has in fact reduced slightly. Review of the constraints which limit the longwall results, i.e. shearer speed, AFC capacity, support, advance rate, and man travel speed, shows that little improvement can be expected in the ideal production rate in thinner seams. In thicker seams the AFC often proves the overriding constraint and further increase in equipment size could lead to increased future ideal production rates and is expected. In all cases a concerted effort to increase the utilisation achieved is likely. For deep mines with thin to medium seams this offers the most viable path to improvement; by contrast thick seams with highwall/shallow access may benefit from further increase in equipment size.

Jan 1, 1988

In any strip coal mining operation the aosL important single operating unit is the dragline. Because the capital and operating costs of a dragline are high, it is desirable to operate these machines at their maximum efficiency. Thiess Bros. Pty. Limited operate a Bucyrus-Erie 1350 Walking dragline at their Callide coal mine. The operating conditions at the Callide Mine are different from those of other coal mines situated in Central Queens ,nd. The topography is rugged, the coal seam is thick, and the overburden is hard and inter- HH,inded. Several different operating techniques for a large dragline working under these con- ditinns arc discrossmd it tt

Jan 1, 1978

The development of the Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves is a significan step towards informing the financial community and the public about the future profitability and risks of investing in resource companies. The Code is also important from the accountants' point of view because it provides them with a well-defined bash for assigning costs or attributing value to the assets of resource companies and hence improving their financial reports. Although reporting to the public is ultimately the responsibility of management, accountants, like geologists, are frequently required to provide information for inclusion in these reports. Jr the last ten years, there has been a considerable refinement in the reporting of mineral resources which can be attributed mainly tc the progress made towards developing the Code. It seems tha the classification and terminology that the geologists have developed are widely used in the annual reports. However, little progress has been made by accountants in improving the financia information. The purpose of this paper is twofold: (a) to outline briefl) some of the major problems in accounting and reporting fo; mining companies and; (b) to examine the potential contribution of the Code in solving those problems.

Jan 1, 1990

By Parsons A. E

The application of known pelletizing tech- nology was successful in the agglomeration of zinc concentrate into pellets of minus 6mm siz- ing using fine zinc calcine and sulphuric acid as binder. Subsequent roasting trials conducted in a 0.3 m diameter fluid bed reactor, showed that the pellets satisfactorily withstood hot physical abrasion during fluidization. Fines generation was low and the pellet calcine was hard, possessing excellent handling properties. Results of laboratory scale static pellet sinter- ing tests showed conclusively that the deterior- ation in sinter physical quality experienced with fine calcine was not apparent when the calcine was added to the mix in pellet form. Based on the results of small scale exper- imental work, a one tonne per hour pilot plant was constructed and operated. Several thousand tonne of pellets were produced-for fluid bed roasting in Badische Analin and Soda Fabrik (B.A.S.F.) turbulent layer (T.L.) roasters previously designed for roasting iron pyrite concentrate. Continuity of the T.L. fluid bed roasting operations was achieved when the waste heat boilers were replaced with atmospheric coolers and thus eliminated the problems of gas flow restrictions. Sinter plant trials were conducted over a period of two weeks with the addition of pellet calcine to the sinter feed. Results showed a marked improvement in sinter plant performance, and as a result of better bed permeability, increased sinter production was achieved, with- out significant deterioration in sinter quality.

Jan 1, 1974

By S H. Sie, R Seetharam, K Naito, T Takagi

Tin-polymetallic vein type deposits are one of the major source of metal producers in the Circum Pacific Belt. This type of deposit is of great importance for the modem electronics and medical industries because of their high content of rare metals (especially indium and bismuth). We have studied two representatives, Tosham of India (Cu-In-Bi-Sn-W-Ag-Au), and Mount Pleasant of Canada (Zn-Cu-In-Bi-Sn-W), using proton and electron microprobes in order to delineate the distribution of medicallhigh-tech rare metals. The electron microprobe study showed that major indium carrier in such type of deposit are roquesite (CulnS2), sphalerite, stannite and a Cu-Zn-Fe-In-Sn-S mineral; and that indium is incorporated in sulfides by coupled substitution like Cu + In = 2(Zn + Fe). The proton microprobe showed that indium at trace levels is also present in chalcopyrite and pyrite. In addition, zinc, copper, arsenic, antimony, selenium, tin, and bismuth are common in chalcopyrite and pyrite. Arsenopyrite contains nickel, copper, zinc, silver, tin, antimony and bismuth. In chalcopyrite and pyrite, zinc, arsenic, indium, bismuth and lead are higher in Mount Pleasant ore, but silver is higher at Tosham. Also thallium and gold were found only in Tosham pyrite. The Tosham deposit is genetically related to S-type magma, while the Mount Pleasant deposit is related to A-type granite. Tosham ore contains zinc-bearing biotites that coexist with chalcopyrite in ore bodies but Mount Pleasant ore lacks such biotite. We propose that the difference in elemental abundance between the two deposits are caused by the different character of source magma and different mineral associations of the ore body.

Jan 1, 1995

THE filter-press, which has done so much for the successful-treatment of the sulpho-telluride ores of Kalgoorlie, has a serious rival in the vacuum process, and this paper is written with a view to arousing more interest in the cheaper working of the press, it being doubtful whether its efficiency in extraction can be improved upon. Before proceeding with the actual working of the press, it may be as well to make brief mention of the character of the ore treated at the Associated Northern Blocks, where these notes were compiled. A sample from several weeks' run was taken of the raw ore, with the following analysis...

Jan 1, 1911

By Fuller P. G, Miller D. R

Hydraulic fill using surface sand deposits or cycloned tailings has been used in underground mining for at least fifty years. Current technology requires a permeable fill and high cement additions for strong fill. Shortages in quantities of acceptable fill with finely ground ore may require rockfill or aggregate to be introduced as a supplement and these usually incur additional distribution costs. Alternative approaches to the problem are now being developed whereby the pulp density of the fill is raised so that it is delivered either as a dense slurry or as a paste. These regimes of fill behaviour are defined together with the plant and pumping techniques required to prepare and deliver the materials. Test techniques to define the different regimes of behaviour are identified and the variation in material properties for fills with varying pulp densities are outlined. The results indicate that high pulp density fills are stronger and have less permeability restrictions than conventional fills and that aggregate can be carried with the pulp. Thus the disadvantage of finer materials can be turned into an economic advantage. Criteria are developed for defining the type of operation suited to this Technology.

Jan 1, 1986

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988

Thermal Processing of Petroleum Fly Ash for Vanadium Recovery

Sep 13, 2010

By Gillies A. D S, Just G. D

Coal washability data can be used for assessing coal quality. However, the techniques of using these data to solve quality problems differ from one mine to another and certain problems may never really be investigated due to limitations of the available techniques. One promising way to overcome these limitations is by correct application of geostatistics.A geostatistical study on coal washability data was undertaken based on a data set of closely spaced in-pit bore cores. These bore cores were analysed consistently over a relatively simple geological area. The average distance between the drill holes was about lOOm. There were 78 drill holes available for the area after deleting the erroneous bore cores. During the study, nine extra closely spaced drill holes were drilled within a single mining block.A procedure to construct two coal quality models, a kriging or cokriging model and a simulation model, was proposed. The modelling results for the data above are discussed and results of a mine scheduling exercise based on the models developed are included.

Jan 1, 1992

By Aziz NI, Guo H

Most of the existing models of the mechanisms of drilling and cutting processes are oversimplified in both stress state and failure criterion. On the other hand numerical modelling techniques are a more versatile method with great potential for development. In reviewing drillability and predicting performance of excavation machines the empirical tests, which simulate the physical breakage action in excavating processes are seen to be the best in terms of penetration rate predictability. Future methods of determination of drillability should concern the breakage characteristics and rock abrasivity involved in the two basic types of attack, i.e., percussive and rotary drilling.

Jan 1, 1988

By Schonert K

The throughput of a HP-roller mill is determined by the acceleration of the feed material within acceleration zone and introduction into the compression zone. Both processes depend on the internal friction and the friction of the material on the roller surface which is influenced by the surface structure and adhering of material. The particle motion in the acceleration zone has been investigated with high speed videos showing the effect of the centrifugal force and the slip on the roller surface. The throughput is discussed in the term of the specific throughput which can be approximated by a linear function characterised by the throughput number and the throughput elasticity. The throughput number is a helpful measure for investigating the influence of the feed material and the surface structure. The experimental results give some guidance for chosing an optimum corrugation profile.

Jan 1, 1993

By Wilkinson LR

The object of this paper is to present a brief overview of applications of radioisotopes in mineral processing. The emphasis is towards on-line applications, and is to present the broad picture rather than become involved in the details of particular applications. For a more detailed and comprehensive coverage, the reader is referred to the International Atomic Energy Agency International Symposium on Nuclear Techniques in Exploration, Extraction and Pro- cessing of Mineral Resources, held in Vienna 7-11 March, 1977. Because of space limitations here, we have inmost cases restricted coverage to those applications of radioisotopes within the direct experience of Amdel and Australian research bodies. Radioisotopes spontaneously emit energy in tiie Form of a and S particles, and electromag- netic radiation. The electromagnetic radiation is generally referred to as y-radiation when it originates from the nucleus, and X-radiation when originating from the electrons orbiting the nucleus. X-ray and y-ray energies overlap, with X-rays extending from a few electron volts (%') up to about 100 keV. Gamma rays in the useful energy range extend from a few keV up to .feV.

Jan 1, 1978

It is a privilege for me to participate in this vitally important discussion of The Role of Governments in the Management of Resources. The distinction of my fellow participants is evidence that this event is a matter of extreme importance and attracts international attention. In the management of natural resources, government and private enterprise share awesome responsibilities for the economic well-being of nations. Mining and its relation to the prosperity of nations is almost as old as recorded history. Copper was being mined and extractive metal- lurgy practised at Timna in Israel's southern desert as far back as 4000 B.C., and the rich mines of Laurium not only saved the Greeks from Persian domination 2500 years ago, but also provided Athens with a monopoly of silver in the Mediterranean world. This bolstered the economic power of Athens and led to the golden age of Greek commerce and culture.

Jan 1, 1978

Total extraction is a misnomer and invariably some coal losses occur in the mining of pillars. "Fulls" pillar extraction is by the pocket and fender method, the splitting method or the open end method, with extraction in the pillar, and in rows of pillars in planned sequence, using combinations of coal and timber and roof-bolts for support. Where circumstances dictate, partial extraction is used, leaving behind portions of pillars in large blocks for support. The use of such extraction plans and supports as minimum guidelines has contributed greatly to safety in United States Coal Mines.

Jan 1, 1974

By Alwan M

At Binebase mineralisation is hosted within an andesitic Neogene volcaniclastic succession on Sangihe Island, Indonesia. Two major alteration types occur; an initial widespread phyllic assemblage of quartz -illite with chlorite, smectite, gypsum and pyrite, and a superimposed quartz - barite - sulphide assemblage. The phyllic alteration arose from a neutral to weakly acidic hydrothermal solution of greater than 200 degrees C, and the quartz - barite - sulphide assemblage arose from a cooler slightly more acidic fluid. This second alteration event is interpreted to have selectively replaced permeable volcaniclastic breccias and coarse lithic tuffs within the altered sequence. Gold and silver mineralisation is associated with the latter alteration, and is locally controlled by the degree of silicification and sulphide abundance. The sulphides present are pyrite, covellite and chalcopyrite. The sulphides are very fine grained with colloform and framboidal textures and were deposited contemporaneously with the bulk silicification of the coarse sediments. A large portion of the mineralised rock has been oxidised to a quartz - barite -limonite - goethite - jarosite assemblage.Coincident gold, silver and antimony geochemical soil anomalies gave the best correlation with anomalous gold and silver grades in bedrock as identified by drilling. Resistivity proved a reliable geophysical method for delineating zones of silicification.

Jan 1, 1990

By Pietrobon M. C, Ralston J, Smart St C R

In an on-going study of the chemistry of base metal sulphide flotation, the effect of the inclusion of cyanide in the reagents suite has been studied, with special reference to ore from Pasminco Mining's Elura mine. Cyanide has been variously described as an iron sulphide depressant, a preventor of sphalerite activation and as an activator of galena. In the case described here, the cyanide appeared to act as an enhancer of the galena flotation performance, raising the lead recoveries by 25 per cent but leaving the sphalerite and pyrite responses unaffected. The lead rougher flotation performance with and without cyanide was investigated over a wide range of redox potentials (0 mV to 400 mV SHE). In all cases, the inclusion of the cyanide brought about an increase in the galena recovery and was responsible for a faster rate of galena flotation during the initial stages of the beneficiation. A surface characterisation study (XPS) of the lead flotation stage, with and without cyanide, indicated that the reagent interacted specifically with the galena and pyrite minerals. It was possible to correlate the surface absorption of the cyanide on the lead and iron sulphides with improvements to the flotation performance using the combination of surface spectroscopy and laboratory flotation Testwork.

Jan 1, 1991

Roof bolting with resin bonded bolts has been developed extensively in French coal mines. There are three aspects of this development: 1. The reason for and the care used in the development of roof bolting from use as a reinforcement in a classical arched roadway to use as the only support in roadways in ad- vance of the working face (the roadway being reinforced behind the face); 2. The problems encountered and studied, such as choice of boltable roadways and determination of the technical data in designing a roof bolting pattern; 3. Only because roof bolting has been controlled by safety rules, and especially by accurate measurement of strata behaviour, has this system of support been expanded aapidly in France since 1967.

Jan 1, 1971

By Moxon N. T, Berndt J. R

BHP-Utah Coal Limited's Peak Downs Mine is located in Cen- tral Queensland, approximately 200 km south west of Mackay. The annual raw coal production of the mine is over 8 million tpa, requiring the removal of about 40 million cubic metres of prime overburden. This is achieved through the use of five large draglines. The large depths of overburden (up to 55 metres) encountered over half the strike length of the mine enables cast blasting to be carried out in conjunction with draglines employ- ing the chopping method of digging. The objective of cast blast- ing is to use explosive energy to move as much material directly into spoil as possible. The additional costs of drilling and blast- ing are offset by reducing dragline rehandle. Two factors which are of primary importance to the design of cast blasts are initiation control and material velocity. High speed motion picture photography is a powerful diagnostic tool to quantify these aspects of blasting (Winzer, Montenyohl and Ritter, 1979; Chiappetta et al., 1983; Anon., 1983). The objec- tives of such analysis are to: 1. Determine the burden velocity, 2. Determine the time to initial movement (that is, the inter- val between a face hole firing and the initial movement of the burden), 3. Check the accuracy of the initiation sequence. BHP Central Research Laboratories (CRL) and Peak Downs Mine monitored a cast blast in the mine's Winchester Pit on 18 August, 1988. The objectives of this exercise were to: 1. Quantify current cast blast performance, providing a base case for comparison with modified blast design. 2. Compare two orientations of angled holes within the blast. 3. Assess the effectiveness of cast blasting utilising an air-deck. 4. Check blast timing with respect to burden movement times.

Jan 1, 1989