Search Documents

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

By Young DJ

Gold mineralisation at the Hamata prospect is related to a series of stacked pyrite and quartz-pyrite veins associated with a number of shears which strike N to NE and dip E. Mineralisation is contained entirely within the Morobe Granodiorite close to the intersection of the Upper Watut Fault and some younger NE to SW striking faults. The prospect was originally detected in 1987 by a regional stream sediment sampling programme. Subsequent mapping and sampling outlined an anomalous zone approximately 900m long by 300m wide. Drill testing has indicated a resource of 46Mt at 0.9 g/t Au.

Jan 1, 1991

By T Elms, R Beckman, M Sampson

"In today’s mining industry, the pressure of reducing costs and increasing production while maintaining high safety standards is at the forefront of operational endeavours. A combination of specific mining knowledge and technological advances has helped enable this notion. Fleet management systems have been developed to enable sites to better measure and manage production to improve operational efficiency.The integral part to managing production is having accurate, readily accessible data. This empowers key stakeholders in the management team to drive production reporting, materials tracking and budget forecasting.If a site does not run a fleet management system, manual input is heavily relied upon for production data, which introduces increased risk of human input error. Errors can drive outcomes that don’t achieve increased production at a reduced cost. Alternatively, a fleet management system can have improved accuracy but involves a high monetary investment. Such an investment is not always feasible for smaller mining operations subject to current industry cost pressures.The Emeco Operating System has been developed in alliance with sites such as the Mungari White Foil Operations by satisfying the criteria of a low intensity hardware installation, material tracking data validation processes, remote monitoring, identification of metrics to improve overall operating efficiency and providing the right information to key stakeholders.Citation:Beckman, R, Elms, T and Sampson, M, 2016. Getting Accurate Mine Information to the Right Teams to Drive Production Improvement, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 203–211 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

This paper outlines the role of commissioning in the project cycle, shows how to get organised for commissioning and describes the principal commissioning activities. Emphasis is placed on appointing key commissioning staff early in the project to coordinate the preparations for commissioning and on detailed planning and tracking to ensure that the required commissioning activities are performed satisfactorily. The management of safety during commissioning is reviewed.

Jan 1, 2005

A mineral exploration manager's prime function is to provide a frame- work within which new mine production can be achieved. As part of this framework, the manager should know his employerb future requirements, and should direct exploration towards those particular mineral commodities which indicate satisfactory growth in consumption and price. Selection of these commodities can be assisted by studies of world reserves, and long term trends in price and consumption. Exploration planning is most efficient with an assured and reasonably uniform supply of funds.

Jan 1, 1980

By M DellÆAmico, K Vining

The iron blast furnace is the most widely used and efficient producer of liquid iron; however, emissions from sintering and coking cause environmental pressure for the integrated steel works. The combustion of coke fines (breeze) during sintering contributes to greenhouse gases (GHG) (eg carbon dioxide) and is a source of SOx and NOx emissions. Coking capacity is also constrained by environmental concerns and economic factors, such as increased coke consumption, and short supply is leading to high prices. Improved coking practices, which result in reduced production of fines, are also contributing to the tight availability of breeze for sintering. This combination of factors presents an opportunity to consider alternatives to coke as a fuel for sintering. CSIRO Minerals has been investigating the use of wood biomass/char as a substitute for coke during sintering. Wood biomass, or char produced from it, is an attractive carbon source as carbon dioxide liberated during combustion can be sequestered back into growing biomass. It has great potential to reduce the emissions from integrated steelworks and improve their environmental acceptability. Harvested biomass/char is also a renewable and sustainable resource and can be integrated with good land management practices such as remediation of salinity affected land. Weeds, especially woody weeds, can also be used as a source of biomass for charcoal, and integrating char production with weed management can help address a pressing environmental issue in Australia. Previous reported preliminary testwork indicated that the use of Red Gum char as a replacement for coke resulted in a product sinter of comparable quality, improvements in productivity and significant reductions in SOx and NOx emissions. In the latest testwork, CSIRO has examined the properties of a range of potential charcoals, and has conducted a further series of granulation and small-scale sintering trials with them in simulated Japanese Steel Mill iron ore blends. Sinter fuels characterised and evaluated include industry sourced coke breeze, commercially available wood char and a charcoal from prickly acacia (acacia nilotica). Prickly acacia has been declared a noxious weed, is widespread in Australia, and is classified as a æWeed of National SignificanceÆ. The results presented in this paper support the notion that charcoal outperforms coke in many aspects of iron ore sintering and factoring in environmental considerations makes the switch to charcoal even more favourable.

Jan 1, 2005

By Marshall GA, Dickerson AW

The efficient operation of large haul trucks in large open pit mines requires an economic trade off between the haul route quality, the haul truck payloads and the level of haul truck reliability. This paper describes an investigation into the relation- ship between haul route surface quality and the level of structural reliability of a haul truck main frame. An instrumentation system for unattended recording of data on a haul truck operating normally in a mine and com- puter based analytical procedures were developed and used to identify which road segments contribute significantly to fatigue cracking at various sections of a haul truck main frame. INTRODUCTION In many open pit mines there is exten- sive use of large haul trucks to move over- burden and minerals. In most open pit hard rock mines, both the overburden and mineral ore are moved by large rear dump type haul trucks. Similar haul trucks are also widely used for coal overburden and mine site coal haulage operations in New South Wales, South Australia and Western Australia. Large bottom

Jan 1, 1982

The carbonatite-hosted apatite deposit at the Cajati open pit mine in the Jacupiranga igneous-carbonatite complex is located in south-eastern Brazil. The major styles of apatite mineralisation include veins or veinlets, small pods or patches, disseminated apatite and locally massive aggregates. The metallurgical concentration of the apatite is accomplished by grinding the carbonatite, removal of magnetite with a magnetic drum, size classification with cyclones and flotation to suppress carbonates and collect apatite. To examine the character of the apatite grains and to apply those observations to apatite beneficiation, specimens of carbonatite were collected from recent exposures in the mine and from selected drill holes. This study utilised a variety of microscopy methods, including transmitted and reflected light, cathodoluminescence (CL) and scanning electron microscopy with wavelength-dispersive spectrometers for mineral compositions. It was found that LREE, Na and Sr are the main elements replacing Ca in the apatite, with relatively low oxide contents (<0.5 per cent, but up to about one per cent for Sr). LREE and Sr contents consistently increase in the latest intrusions (C4, C5 and SP24). Chemical and morphological modifications of apatite were recognised to be related to detrimental effects on flotation recovery. Three examples illustrate this relationship: 1.  Apatite with reddish CL is fractured. Locally that apatite exhibits no CL due to CL quenching caused by iron entering the apatite structure.2.  Apatite from the xenolith-rich area exhibits abundant fine, platy silicates that appear to interfere with flotation and lower apatite recovery.3.  So called æhardÆ apatite, which is more difficult to grind, occurs in an area in the mine that was affected by hydrothermal activity. That activity is evidenced by the development of a bright, white CL rim in the apatite, and by the presence of late veins of carbonates and sulfides that fill fractures and appear to contribute to higher cohesiveness of those apatite grains.

Jan 1, 2008

By Feebrey CA, Duncan RA

The Ebor Volcano in northeastern New South Wales is an eroded example of a central-type intraplate volcanic-intrusive complex. It is of Miocene age (19-20 Ma) and has similarities to other central-type volcanoes in eastern Australia which may represent manifestations of sub-lithospheric hotspot activity. Thick lava flows are exposed around the Great Escarpment and are dominated by a tholeiitic basaltic suite, ranging from ol-tholeiite to qz-tholeiite to icelandite with ages of 19.2-19.6 Ma. On its western edge, the tholeiitic lava suite probably overlies remnants of basanite flows belonging to the Eocene (-48 Ma) Doughboy province, but elsewhere, minor alkaline basaltic lavas may be coeval with the tholeiitic suite. Several felsic bodies were emplaced into the volcano at -19.0-19.2 Ma and include subalkaline and peralkaline types. The Crescent Complex is a Miocene-age, strongly differentiated mafic to felsic intrusion in basement rocks and centrally located in pre-erosion reconstructions of the Ebor Volcano. It is interpreted to be a major feeder for the tholeiitic lavas based on age and composition. Evolution of the dominant tholeiitic suite proceeded from a parental ol-tholeiite magma, through qz-tholeiite, icelandite and small volumes of felsic rocks by fractionation of plagioclase, olivine, clinopyroxene and titanomagnetite, accompanied by enrichment of SiO2, F,FeO/MgO, alkalies and HFSE.

Jan 1, 1995

Stope filling practice on the Great Boulder Mine was described in -a paper published in Aus.I.M.M., Proceedings No. 137, in 1945. When the paper was presented the process had emerged from the experimental stage, most of the initial operating difficulties had been overcome, and it had been established that this method of filling was suitable for the working of ore bodies in the Kalgoorlie field: Since 1945, it has fulfilled its early promise, -and during 1947, the tonnage of fill placed was sufficient to cover current operating requirements as called for by the mine ore breaking programme. The object of this paper is to outline current operations. In so doing it will refer' to some ground covered by the previous paper, but will omit details of the initial experimental work. It will include, however, a description of further experimental work on the use of hydraulic filling for worked-out shrinkage stopes, arid will provide more accurate data on costs than were available previously.ESTIMATE OF TONNAGE OF FILL REQUIRED.Early in 1946, the mine ore reserves were analysed in order to estimate the relative tonnages to be mined per four-weekly period by shrinkage stope methods -and by cut and fill stope methods respectively. This analysis was extended beyond the blocks already prepared for stoping, and inclqded the majority of the major ore blocks in the mine ore reserves. It gave the following results:-For a mill tonnage of 28,000 tons per period, 6,933 tons were required from cut and fill stopes, and a possible future maximum programme of 35,000 tons per period would require...

Jan 1, 1948

By A Nixon

The Australian mining industry has changed dramatically over the past 20 years in terms of mining methods, mining equipment and human resource policies. The industryÆs approach to safety and health in terms of attitudes, style of legislation, and risk management techniques has also changed significantly. These changes have had and continue to have major impacts on the design of underground mine ventilation systems. In some areas, trends are clearly emerging. In other areas, mine ventilation planning remains very æreactiveÆ and is performing poorly in terms of providing a safe and healthy work environment at a reasonable cost. New concepts involving the role of ramps and shafts, the provision of refrigerated air, æventilation on demandÆ and newe gress and entrapment approaches are likely to be incorporated into mine planning and operating practices over the next ten years. This paper discusses these and other trends and identifies some likely future developments in the area of hardrock mine ventilation.

Jan 1, 2005

By D Thornton, R Hodson, D Sprott

Blast fragmentation size distribution and thus blast design have been found to have a direct impact on the load and haul cycle through excavator dig time and bucket payload. Previous studies have demonstrated that by reducing the excavator dig time and increasing bucket payload, significant improvements can be made in both productivity and unit cost. Simulation work reported in the literature indicates that a 20 per cent improvement in dig time may result in only a three per cent improvement in load and haul productivity and unit cost. At the same time, a ten per cent improvement in bucket payload will directly translate to a ten per cent improvement in load and haul productivity and unit cost. Based upon these findings, extensive laboratory and field work have been undertaken in the past to correlate blast fragmentation distribution to bucket payload. In contrast, the literature reports limited studies quantifying the impact of blast fragmentation on excavator dig time. Field work was conducted at Placer Dome Asia PacificÆs Granny Smith Mine (Wallaby Pit) in Western Australia, concentrating on quantifying the impact of blast fragmentation on the dig time of a Liebherr 994 hydraulic excavator (shovel attachment with 14 m3 bucket). Fragmentation was assessed for each truck load of material using the Split Desktop system, while the excavator cycle analysis was conducted manually. Measured fragmentation P80 (fragment size at which 80 per cent of material passes) values ranged from 200 mm to 1200 mm. The field study investigated the impact of various fragmentation parameters (P20, P50, P80, cumulative per cent passing 250 mm size fraction, and uniformity index) on the average and total dig times. The results indicate that the fragmentation P80 provides the best correlation to average dig time (total dig time divided by the number of bucket passes to load a truck). The total dig time was found to be dependant upon the fragmentation P80 and the number of bucket passes to fill a truck. Monte Carlo simulation results, based upon these relationships, indicate a 26 per cent improvement in average dig time and a 12 per cent to 46 per cent improvement in total dig time (bucket passes ranging from 4 to 8), with a change in fragmentation P80 from 600 mm to 200 mm.

Jan 1, 2003

By C Hall, K Williams, B Keogh, S Wong

Cannington mine is a silver lead zinc operation located in north west Queensland. The operation has been in production since 1997. Ore is primarily moved through an underground material handling system comprising of a crusher, conveyor and hoist. The underground crusher and conveyor system were sited in lower grade ore when the mine was first commissioned. As Cannington is now a mature operation, this ore is considered run of mine and stoping progressed into the crusher exclusion zone. As the stoping fronts advanced there was increased damage on the crusher chamber and infrastructure. In response to monitoring data, the crusher monitoring system was significantly upgraded in 2016. The monitoring system included rock mass and infrastructure instrumentation. It improved the understanding of stress impacts and mechanisms driving the damage within the chamber. It allowed the site geotechnical team to respond to changes utilising ground support, mining sequences and increased levels of monitoring. As stoping and damage to the rock mass continued, so did the process of responding to monitoring data. Ultimately, the monitoring system enabled a safe and controlled closure of the chamber. CITATION:Williams, K, Keogh, B, Hall, C and Wong, S, 2018. Monitoring as an input to support and sequence design, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 446–452 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Ariti J

The mineralogy and extractive metallurgy of platinum and palladium in ores and residues is examined and the relative reactivity of Pt, Pd, PtS and PdS in cyanide and chloride media at 20¦C is discussed. Electrochemical measurements establish that Pd is readily leached in chloride media but more slowly in cyanide media due to a passivating PdO film. The passivating oxide film on Pt prevents leaching in either system at ambient temperatures. The results of leaching Au, Pd and Pt from an iron oxide residue obtained from the Sherritt Gordon Process using CN/air and Cl-/H202 are compared. It appears that passivation is overcome either by roasting at ?600¦ or by leaching at >_100¦C.

Jan 1, 1991

By B Cook, M Karakus, J Light, E K. Chanda

The aim of this research is to develop a model through which the appropriate paste recipe parameters, for example solid content and cement content, can be derived given the stope specific requirements such as stope dimensions, required strength and curing time. A large number of samples and uniaxial compressive strength (UCS) tests were conducted at the Angas Zinc Mine (AZM) paste plant and testing facility. Samples were varied in tailings solids content, cement content and sand content. The results of this testing were modelled to determine the UCS relationship to each of the parameters. The output of this modelling was an easy-to-use program that outputs the design mixture given the stope dimensions and required stope backfill-curing time. This allowed flexibility within the mining schedule for curing times of cemented paste backfill stopes. The optimised schedule using the stope specific mix design, when compared to the standard 14-day curing time used previously, resulted in a smoother weekly mine production schedule. For the modelled 12-week period (one quarter) the 14-day curing time would result in an eight-day shutdown of the mill. The cost for each shutdown is in the order of $125 000/d. Due to the unique nature of each mine’s tailings, this exact outcome would not be directly applicable to another paste fill site. However, the process in this report could be followed for another site to achieve a system similar to the output of this project. This would ultimately lead to a more optimised backfill and stoping cycle and a more optimised mine.CITATION:Chanda, E K, Karakus, M, Light, J, Cook, B and Harris, A, 2014. Optimisation of the paste fill cycle at Angas Zinc Mine, Strathalbyn, South Australia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 259–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

The underground coal mining industry in Australia has, in the last 30 years, undergone a revolution in production methods, techniques and results probably unparalleled elsewhere in the world. It can lay claim not only to leading the fight against pneumoconiosis and setting high safety standards generally, but has at the same time recorded comparatively high rates of increase in output per man shift. The latter has been achieved as a result of progressively matching the latest in production and underground transportation equipment with significant changes in seam development and extraction techniques and the introduction of stress-relieving extraction methods unique to the world scene. However, the seam recovery factor is still too low. Apart from the overall objectives of maximising production and commercial returns with the greatest safety, there must be a concentration towards maximising seam recovery, particularly in high seams. The search will continue for systems which are more completely continuous mining operations than the present stop-go operations, with longwall having long term potential in this regard, but as yet not sufficiently developed to engender confidence for its more general use. Techniques developed in the last 10 years make the development and extraction of deeper seams, perhaps to 2500 feet or more, feasible with continuous miners as well as longwall. The future will see a greater use of continuous shifts at mines, larger mines with more sophisticated management organisation, extensible belts at the face, better systems of immediate roof support at the face, remote operation of face equipment, greater use of roof bolts and the longer roof cables. With commercial confidence in coal mining now virtually assured to at least the turn of the century, the stage is set for heavy capital development in the industry which will undoubtedly include major research into the whole area of mining methods and equipment. We must ensure that our contribution to such research equitably matches other coal producing countries.

Jan 1, 1975

By Kepplinger W

The KR Process is a joint development by VOEST-ALPINE, Austria and its subsidiary company KORF ENGINEERING, Germany. This new technology allows production of hot metal on the basis of non-coking coal. The KR Process is based on the idea of separating the process steps realized in the blast furnace (generation of reduction gas, reduction of iron oxide and melting of the reduced iron) and including coking of coal. These reactions are carried out in two reactors: - the melter gasifier, where non- coking coal is coked and gasified into a high quality reduction gas and hot prereduced iron is melted. - the reduction furnace, where iron oxide is reduced by the reduction gas generated in the melter gasifier and discharged in a hot state. In order to prove the process a pilot plant has been set up in Kehl/ Rhine in 1981 with a nominal capacity of 60.000 tpy.

Jan 1, 1986

By Garg R. K

Himalayan ranges on the northern border of India are source of many perennial rivers and suitable sites for large dams have been located therein. However, Himalayas are young mountains and comprise of comparatively weaker rocks having adverse geological features like shear seams, thrust zones, minor and major faults and intense jointing. Tehri dam project under construction, is located in lower Himalayas. It envisages construction of a 260.5 m high earth and rock fill dam and an underground power station of 2000 MW (Eight machines of 250 MW each, four of which will be reversible) installed capacity. This dam will be the highest and the underground complex will be the largest to be constructed in India in the Himalayas. The under- ground complex comprises of 25 km of tunnels varying in diameter from 6 m to 11 m and seven large cavities of various sizes, the biggest being 22 m in width, 194 m in length and 65 m in height. Rock formation in the power house complex belong to phyllites having various joint sets spaced from 0.5 m to 3 m. Due to the poor geological conditions and closely spaced net work of large cavities, the planning, analysis and design of the cavities is a challenging job. Many aspects have to be considered in determining the sizes, locations and orientations of the various cavities taking into account the properties and jointing pattern of rock mass, functional requirements and economics. Correct evaluation of loads and forces is necessary for economical design of supporting system for the various cavities. Rock loads on the roof of cavities and their supporting system will be assessed with the help of the latest methods. The stability of the rock mass around the cavity will be evaluated by elasto- plastic method using finite or boundary element techniques. A scheme of field investigations, laboratory tests and instrumentation for deter- mining rock properties in preconstruction stage and for monitoring behaviour of the underground cavities during and after construction is envisaged.

Jan 1, 1987

Rajor intrusion-related Cu and Au dep- osits along the Cordilleran-type central Andean margin and in the western Pacific island arcs constitute a series of discrete, linear belts which correspond to limited (414 m.y.) metall- ogenic epochs. The most important metallogenic belts, all of Cenozoic age, are inferred to have been generated during relatively shallow subduction of oceanic lithosphere beneath con- vergent margins. Geological and isotopic evid- ence suggests that magmatic rocks and associated Cu and Au mineralization were derived from asthenospheric mantle sources, which were enriched in a variety of elements (metals, alkalis, S) by dehydration of subducting oceanic crust. Where exceptionally rapid, low-angle 3ubduction took place beneath very thick (>50 km) continental crust, as in the central Andean Altiplano in the Miocene and southwestern North America during the Laramide, ore-related magmas underwent wholesale crustal contamination. However, the associated Cu-Au mineralization is the same as that developed in primitive island- arc crust. In particular, the by-product Au and So contents of porphyry Cu deposits are inde- pendent of crustal thickness and the degree of crustal contamination as determined isotopic- Ally.

Jan 1, 1987

By A Parbhakar-Fox, B G. Lottermoser, N Fox

"Determining the deportment of economic and environmentally significant elements in sulfidic mine materials (eg ore, gangue and waste) requires the use of advanced microanalytical techniques, including electron microprobe analysis (EMPA) and laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS). Sulfidic boulders were sampled from an acid rock drainage impacted ephemeral stream adjacent to historical copper-silver workings at Baal Gammon, northern Queensland. The abundance and deportment of a range of trace elements and precious metals were analysed in these samples. Whilst many of these elements represent a potential environmental risk if leached from sulfidic rocks into streams in the surficial environment, significantly some of these elements (eg In, Sb and Co) represent specialised metals that are currently considered to be in critical supply.Sulfidic waste rock material at Baal Gammon is dominated by chalcopyrite, arsenopyrite, pyrrhotite and pyrite. Microanalytical investigations revealed that chalcopyrite contains significant quantities of In, Sn, Ag and Zn either substituted directly into the crystal lattice or occurring as discrete sphalerite and stannite inclusions. Arsenopyrite, which may comprise more than 50 per cent of some boulders, is notably enriched in Sb, Co and Ni but also contains inclusions of sphalerite, chalcopyrite and stannite. In contrast, pyrrhotite contains no trace elements of economic significance, but instead represents a likely contributor to acid generation during oxidation in the surficial environment. Trace metals (eg In, Sb, Co, Ni, Zn) are liberated during sulfide oxidation of these boulders in the surficial environment, generating a metal-rich, low-pH leachate.Fe-oxides precipitated as rinds on the surface of these boulders under low pH conditions also contain abundant As, Bi, Sn, Cu and Zn. Abandoned or historical mines represent potential sources of metalliferous drainage that poses potential environmental risks to water and habitats. However, sulfide-rich historical waste rock, stockpiles and processed waste (eg tailings) at abandoned mines may also represent significant sources of critical (eg indium) or other significant metals (eg Sn) that if liberated economically could improve environmental conditions in and around abandoned and historical mines.CITATION:Fox, N, Parbhakar-Fox, A and Lottermoser, B G, 2016. Critical and Deleterious Metal Deportment in Sulfidic Waste Rocks, Baal Gammon, North Queensland, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016