Search Documents

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Wymer DG

The concept of hydro power in deep mines is based on the exploitation of the hydrostatic head that can be gained as refrigerated cooling water descends in shaft pipe columns from the surface, to provide hydraulic power for machines at the working face. This paper describes the work done on two important aspects of the controlled distribu-tion of the high pressure water within a mine, namely the control of pressure under normal operating conditions, and the control of flow in an emergency situation following a pipe breakage. Suitable methods of control have been determined using theoretical techniques to model the steady and unsteady flow behaviour of the water in the pipeline, and taking into consideration the environmental constraints on the types of control devices that can be used. The preferred approach is one in which the high pressure water itself is used as the control medium. The control valves themselves can be fairly conventional in design, but in the case of pipe break protection it is shown that a less conventional approach based on the use of a hydraulic fuse gives improved control performance.

Jan 1, 1985

It is a great pleasure to accept the invitation to open this Joint Conference of The Australasian Institute of Mining and Metallurgy and the American Institute of Mining, Metallurgical and Petroleum Engineers. It is the second invita- tion to participate in the Conference that I have accepted. When it was being planned, the President wrote to me to invite me to be one of the speakers in one of the technical sessions. I wrote accepting the invitation, and when my present appointment was announced, there was a nice question about the earlier commitment. The upshot of it all is revealed by the present arrange-., ment: you get me as opener and the more sub- k stantial speech is to be given by Professor Rupert Myers, my friend and former colleague who will not only be able to contribute from the standpoint of an experienced University admini- strator, but will also speak from a professional training and experience much more closely relat- ed to the concerns of this Conference than I possess. Though it is a joint meeting and the speakers will include distinguished figures from North America, I hope that since the venue is Australia, I may be permitted to speak with an Australian emphasis. I have recently had a brief glimpse of part of the Australian mining industry. In the course of a journey through the Northern Terri- tory we-my wife and I-visited Gove, Groote Eylandt, and Tennant Creek. At Gove we saw the remarkable Nabalco development in bauxite and alumina and the very impressive town plan- ning development at Nhulunby, the major man- ganese enterprise at Groote Eylandt, and the gold mining activity at Tennant Creek. For lay people like us, a gold pour was arranged at Tennant Creek and that was a spectacular sight. On earlier occasions, and before my present appoint- ment, I had visited Mount Isa and the Utah fields, and Queensland Alumina at Gladstone. I have not seen the cradle of the modern mining industry, using cradle perhaps loosely, at Broken Hill, nor have I seen the great Pilbara develop- ment, nor Weipa. This is not for want of generous invitations and it is my hope that within the not too far distant future this will be rectified. Then there is the Australian petroleum industry and the great industries which make their products from the minerals mined which I have yet to See.

Jan 1, 1978

The need to schedule ore production to make maximum use of the strength gained by cem- ented fill during curing is discussed, to show how cement content and hence fill cost can be kept down for any particular operation. Results from laboratory testwork on Isa Mine fill conducted by the author while employed by Mount Isa Mines Limited form the basis of the Discussion

Jan 1, 1973

By Wright G. A

The objective of refining in steelmaking is to reduce the concentration of impurity atoms, e.g. sulphur, phosphorus, from an initially high level to a specified low concentration. A two-film theory of refining is presented in which the rate of

Jan 1, 1980

Structural assemblages of veins, shear zones, and wallrock alteration zones arising from fault-valve action on steep reverse fault systems are reviewed using observations from mesothermal gold-quartz lodes in the Archean Yellowknife, Abitibi, and Yilgarn greenstone belts of Canada and Western Australia, the Cretaceous Mother Lode system in the Foothills Metamorphic Belt of the western Sierra Nevada, California and the Victorian goldfield hosted in a folded quartz-turbidite succession of Paleozoic age in Australia. Despite differences in the host rock assemblages, the deposits have many structural characteristics in common. These form a useful exploration guide when re-evaluating comparable, but poorly described gold-quartz vein systems such as those in the Reefton area of New Zealand.

Jan 1, 1992

The Marvel Loch Operations (MLO) plant was treating ores from up to six MLO sources and in addition needed to blend externally sourced ores with its own ores. This presented a metallurgical accounting dilemma, which was subsequently addressed by the design, implementation and testing of an automatic sampling system. The MLO automatic sampler was well designed and has been the subject of previous internal and external reviews. The sampling action is fully automated and the unit is essentially self cleaning particularly when sampling primary ores. The purpose of this paper is to document the rationale behind the design, the specific details of the sampling station, its use for ore purchase purposes and an assessment of the sampling system to meet the needs of the operator.

Mar 1, 2010

Over the past 12 years screening of materials has undergone a dramatic change in both the types and materials used in screen mats and the quality requirements of the finished product. With the main thrust now on quality and a cleaner product a different approach was needed in the operation of sizing screens. New screen mats with many different aperture configurations have been developed using rubber and plastics.to replace the traditional screen mat of woven wire or punched plate.

Jan 1, 1984

By G Swayn, J Harpley

Spent Pot Lining (SPL) is an unavoidable waste product of the electrolytic process in the smelting of aluminium. SPL is considered to be a hazardous waste in various countries because it contains significant quantities of absorbed fluoride along with traces of cyanide. The disposal of SPL has been primarily in landfill because of difficulties in the development of a successful techno-economic SPL treatment process. Increasing concern about SPL landfilling practices is resulting in regulations in some countries to ban this form of disposal. As a consequence stock piling of SPL is occurring in an increasing number of countries pending the development of a successful treatment process. In 1992 Portland Aluminium investigated a SPL treatment process based on pyrometallurgical technology and approached a company called Ausmelt in Dandenong, Victoria, Australia, to ascertain if their submerged lance technology furnace process would be suitable to treat SPL. This approach resulted in Portland Aluminium, Alcoa and Ausmelt personnel working together on trials during 1992 - 1994 in Ausmelt's demonstration furnace to produce a slag and off gases containing hydrogen and sodium fluoride. The trials also evaluated the effect of oxygen enrichment to increase the concentration of hydrogen fluoride and the ability to recycle sodium fluoride particulate produced as the furnace off gases cooled. Other separate developmental work by Portland Aluminium, using CSIRO, resulted in the production of aluminium fluoride from the offgases from the pyrometallurgical process. The results of these projects influenced Portland Aluminium and Alcoa to authorise up to $A26 400 000 in December 1995 to construct a Research and Development processing facility to treat SPL at Portland. The Portland Aluminium unique gas treatment process converts hydrogen fluoride in the furnace offgases to aluminium fluoride in a multistage fluidised bed reactor, designed by Portland Aluminium. The aluminium fluoride produced in the reactor has been trialed successfully in Alcoa's aluminium smelting process as a replacement for imported aluminium fluoride. The installation in mid-2001 of a slag granulation system has enabled the production of a granulated vitreous slag having leachability qualities that conform to Victorian EPA criteria for the unrestricted use of the granulated vitreous slag from 'The Alcoa Portland SPL Process'. The unrestricted use of the granulated slag successfully completes 'The Alcoa Portland SPL Process' which treats the hazardous waste material SPL and converts it into non hazardous useful products.

Jan 1, 2002

By E Yurakov, D J. Ashelford, M I. Slate

The push for increasing coal production rates continues to place increasing demands on mine management to safely and effectively control seam gas. Gas drainage strategies applied vary in both effectiveness and form. Methods employed are a function of assessed risk, gas reservoir characteristics, surface and underground access, budgetary constraints and gas utilisation potential. With the aim of establishing and optimising the effectiveness and efficiency of gas drainage systems, Australian coal miners in cooperation with gas management specialists are embracing the use of gas reservoir simulators and gas emission models. This paper discusses the evolution of gas drainage practices in Australian underground coal mines and the role of gas reservoir assessment methods in optimising gas drainage systems and gas production forecasts.

Jan 1, 2005

By D Alexander

For nearly 100 years, the flotation plant metallurgist has often wondered what is happening æbeneath the frothÆ. To assist in unravelling this mystery, new technology has been developed as part of the Australian Mineral Industries Research Association (AMIRA) P9 project, to measure gas dispersion characteristics (such as gas hold-up, superficial gas velocity and bubble size) in industrial flotation cells. These measurements have been conducted in a large number of cells of different types and sizes by researchers from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. A large database has been developed and the contents of this database are described in this paper. Typical cell characterisation measurements show a wide spread in values, even in the same cell types and sizes performing similar duties. In conventional flotation cells, the typical gas hold-up values range from 3 - 20 per cent, bubble sizes range between 1 and 2 mm, and superficial gas velocity ranges from 1 to 2.5 cm/s. The ranges of cell characterisation measurements given in this paper will enable plant personnel to compare their operation to other similar types of operations from around Australia and the rest of the world, giving opportunities for further improvement to flotation plant operations.

Jan 1, 2005

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

Lithocaps are potentially voluminous zones of advanced argillic and associated argillic alteration located above the subvolcanic intrusive environment. They constitute exploration objectives for epithermal and porphyry-type deposits. High-sulphidation epithermal deposits may be sought within lithocaps, whereas low-sulphidation deposits may exist on their edges. Porphyry Cu-Au/Au deposits may be accessible beneath lithocaps if systems are telescoped sufficiently. Oxidation of the basal, pyritic parts of lithocaps may promote supergene sulphide enrichment under appropriate tectonic and climatic conditions.

Jan 1, 1995

By C Berglin

Is the Northern Territory different? Certainly it is more remote, has less people and relies more heavily on two or three industries for its survival. On the other hand, its mining industry is governed by Acts not dissimilar to those of the major States - a Mining Act provides the basis for acquisition of tenure, a Mine Management Act provides regulatory control, a Mineral Royally Act collects revenue in return for the right to utilise the land's bounties, an Environmental Assessment Act provides the public face to rehabilitation and environmental safety, and the Aboriginal Land Rights (NT) Act purports to give development criteria for inalienable land use. With the exception of the latter, at least until the advent of Mabo, all these are simply variations on a theme, and are common to most States. This paper will show how the Department of Mines and Energy works in relation to the Northern Territory mining industry.

Jan 1, 1994

By A Horn

Mineral processing is characterised by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high-grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customer’s requirement for product purity and consistent quality increases.Over recent years beneficiation techniques for iron ore fines have become more important in order to achieve a maximised utilisation of ore resources and to produce competitive products according to international standards.Many high capacity iron ore beneficiation plants that target the production of fines focus on gravity separation processes using fluidised bed classifiers and spirals or wet high intensity magnetic separators as an alternative. This paper demonstrates the suitability of utilising the allflux® two-stage fluidised bed classifiers to treat iron ore particles up to 2 mm in size as well as showing how the high capacity gaustec® wet high intensity magnetic separation (WHIMS) technology offers several advantages compared to other WHIMS technology.The combination of the allflux® and gaustec® technologies offer the following benefits:The two-stage fluidised bed classification extracts a significant amount of concentrate from the feed. This in turn reduces the feed capacity required for the gaustec® WHIMS located downstream.The second classification stage produces a -0.5 + 0.1 mm product and a -0.1 mm product. The efficiency of the magnetic separation on these classifi ed products is high due to optimised settings for each size fraction.

Jul 11, 2011

By J Wen, P Hou, W Yu, M Hu, Z Jiang, C Bai

Vanadium titano-magnetite (VTM) is one of the important iron ore resources in the world. High viscosity and low fluidity are the basic characteristics of hot metal containing vanadium and titanium during the ironmaking process. Clarifying the influencing mechanism of the melt viscosity would be a significant issue for the high efficiency smelting of VTM. In this paper, a self-developed melt viscometer based on the principle of torsional vibration theory was employed to measure the viscosity of hot metal accurately. Simultaneously, the thermodynamic calculations and some modern detection methods were also used to investigate the precipitation behaviour of high-melting-point phases in hot metal containing vanadium and titanium. The measuring results show that the viscosity of molten iron gradually increases with the increase of titanium content when the mass fraction of titanium is between 0.09 wt per cent – 0.50 wt per cent. Meanwhile, the viscosity of the hot metal was affected significantly by the vanadium content. When the vanadium mass fraction was higher than 0.30 wt per cent, the viscosity of hot metal increased sharply, which will have a serious impact on the fluidity of the hot metal. Furthermore, it was revealed by thermodynamic calculations that an increase in titanium and vanadium content would result in the precipitation of high melting point phases such as TiC, TiN, VC, and VN in the molten iron, ultimately resulting in a decrease in its fluidity. Meanwhile, it was confirmed by Scanning Electron Microscope (SEM) observation that the precipitates in the hot metal were compounds consisting of V, Ti, C, and N elements, which agrees well with the thermodynamic analysis results.

Aug 21, 2024

By Hayba DO

Metal-rich slurries discharged from excess-enthalpy geothermal wells at Kawerau (NZ) indicate that an efficient ore precipitation mechanism operates in some feedzones. In our conceptual model, which takes into account the relative permeabilities of liquid and gas phases in boiling fluids, a metal-precipitating liquid phase is effectively immobilised along boiling fronts, leading to the formation of highly concentrated ore. Chemical equilibrium and heat/mass transport modeling demonstrate the general applicability of this conceptual model to hydrothermal eruption environments.

Jan 1, 1995

By G Byrne

Long-term water management is typically ignored in mine closure planning. A review of 73 mine closure plans dating from 2007 to 2013 shows that, on average, relinquishment is proposed to be achieved in 11 years. A separate review of 57 mines in actual closure shows that only five have so far achieved relinquishment with an average closure period of 14 years after production cessation. The remaining 91 per cent of sites in closure have an average closure duration to date of 21 years - and still going.A common issue among those sites in closure is water management, with a further common issue being acid and metaliferous drainage (AMD). Of the closure plans that were reviewed only one site had allowance for long-term (>50 years) of water treatment. Of the sites in actual closure 25 per cent have reported that they expect such long-term water treatment, with many acknowledging that in perpetuity treatment is probable.Clearly there is a gap between what is being allowed in closure plans and the reality of closure. There are a number of factors leading to the optimism of the closure plans, including unrealistic assumptions, pressures to reduce closure cost provisions and the technical complexity of many AMD issues.Long-term water management is a reality that needs to be acknowledged and addressed. If addressed early in the mine life cycle the impacts for mining companies can be reduced.CITATION:Byrne, G, 2013. Long-term water management - the forgotten legacy of mine closure, in Proceedings Water in Mining 2013 , pp 163-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Nine case studies are presented to illustrate how risks can be, minimised or quantified during pit optimisation, utilising Whittle Four-D software. Each case study covers a specific problem that has been encountered from a wide variety of pit optimisations. Case A: Maximising profits when the tenement owner is paid a royalty on tonnes processed. Case B: Allocating product prices, rather than a single commodity price during optimisation. Case C: Quantifying processing costs that are affected by penalty elements in the ore. Case D: Exploration expenditures below current pits can be quantified through the use of simulation techniques. Case E: Alternative strategies can be quantified when pits are restricted by tenement boundaries. Case F: Relocation of mine infrastructure that requires large capital expenditures, can be simulated by allocating costs to an area during optimisation. Case G: Evaluating alternative corporate strategies during pit optimisation. Case H: Sensitivity analysis for price, processing cost and mining cost. Case I: Quantifying the advantages of using additional mining capacity during the early periods of mining.

Jan 1, 1994

By E Kasai, D Maruoka, Y Konno, T Murakami

The iron ore sintering process produces approximately three per cent of carbon dioxide emission in Japan because a large amount of coke breeze is used as the main agglomeration agent. Therefore, its suppression has been required. A promising method is to replace the coke breeze with biomass char and iron-bearing materials. In this study, the effect of the utilisation of metallic iron with coke or palm kernel shell char (PKS char) as an agglomeration agent on its oxidation behaviour was examined by a series of experiments using a sintering simulator. The use of PKS char leads to a larger decrease in the pressure drop difference of the sintering bed compared to the case using coke. Furthermore, the oxidation rate of metallic iron was larger in the case using PKS char together than that using coke. It was considered that the oxidation of metallic iron was promoted because the bed-temperature increased at a faster rate and achieved a higher temperature.

Nov 8, 2021