Search Documents

By D. Harker, M. J. Murphy

The mechanism by which age-hardening takes .place is still not completely understood. The principal theories range from the extreme of "precipitaiion-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. Preparation of Formvae. Replicas of Metallic Specimens This section is concerned with the techniques that have roved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. it is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work—very fine polishing and etching with very dilute solutions—is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. Preparation of Metallographic Specimens The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch—to approximately the depth necessary for a micrograph at 1000 diameters—usually produces a sur-

Jan 1, 1945

By Hugh Henton

THIS paper is the result of an investigation made in association with Dr. Charles H. Fulton. Early in 1918 a search was started for methods of utilizing, in the manufacture of basic refractories, certain domestic resources in magnesites, dolomites, and magnesian limestones. Much information was collected during that year and during 1919 regarding magnesite and dolomite deposits. During 1920 and 1921 a research was made into methods of calcining dolomite and separating magnesia therefrom. Some success was attained and many new ideas were brought out in connection with the preparation and utilization of magnesia in the form of "caustic" or light-burned material as well as in the form of refractory or "dead-burned" material. Stimulated by this success, much advance has been made in manufacturing processes for the "plastic magnesia," so called, used for magnesia cement, stucco, flooring and otherwise in the structural industries.

Jan 3, 1926

By A. R. Kinkel

The Shasta copper-zinc district of northern California lies in the foothills of the Klamath Mountains at the northern end of the Sacramento Valley. It contains two main areas of base-metal ore deposits, the East Shasta and West Shasta districts shown in Fig. 1. The East Shasta includes the area from the Afterthought mine, near the settlement of Ingot on U. S. highway 299 East, to the Bully Hill mine, on the north side of the Pit River, 9 miles to the north- west. The West Shasta, a well-defined northeast- trending district about 8 miles long and 2 miles wide, west of the Sacramento River, Fig. 2, is the western part of the ore-bearing area formerly known as the Shasta copper belt. Referred to in the older writings as a copper arc, this belt was thought to form a crescent extending entirely around the head of the Sacramento Valley, the convex side to the north. Recent studies by the U. S. Geological Survey in cooperation with the California State Division of Mines show that there are two districts, one at each end of the so-called copper arc, which are distinct in geologic structure and ore occurrences, and that there is only sporadic and unconnected copper mineralization between them.

Jan 2, 1955

By David P. Hale

THE Cartersville barite district is near Cartersville, Ga., in the southeastern part of Bartow County, about 43 miles northeast of Atlanta. The area over which active mining is being done extends about six miles in a northeasterly direction and is about three miles wide. Barite production in Georgia began about 1907,1but the existence of the mineral was known much earlier. At present four companies are operating washing plants and three other plants are operating on leases from those companies. The chief impurities in the ores are silica and iron oxide. The silica is easily washed and jigged out and gives little trouble. Any gravity separation between the iron and the barite is generally poor, owing to the slight difference in specific gravity. Two operators have turned to magnetic separation as the solution to the problem and have made remarkable improvements in the finished product. By very close sizing prior to jigging, the separation between iron and barite has been greatly improved. In some localities manganese occasionally appears as an impurity, but is fairly easy to eliminate by gravity methods. A considerable percentage of iron and silica is eliminated by being broken free in crushing. Until methods for the recovery of fine ore were introduced a minimum of crushing was done, but modern methods allow more than formerly. The depression years brought about the need for increased recovery of ore handled on the part of the producers and a demand for a higher grade of product on the part of the buyers. Improvements in milling and mining practice have had a far greater effect, however, than merely the production of a better grade of ore with greater recovery. They have opened for mining large areas that a few years ago were considered noncommercial deposits because of their inaccessibility and their high iron content. It is no exaggeration to say that the new methods have more than doubled present known reserves of barite ore of economic value.

Jan 1, 1938

By Samuel L. Hoyt

Cemented tungsten carbide, a product of a branch of metallurgy which has never possessed more than a relatively minor interest and importance, has recently commanded the attention of engineers, industrialists, financiers and men of business. New methods, new opportunities, new goals, never before considered, have suddenly been brought within the scope of practical realization. It is these results that attract the interest of the world, but we, as engineers and metallurgists, will have equal interest in the product itself and in that branch of metallurgy from which it comes. It seems appropriate, therefore, to speak today on Hard Metal Carbides and Cemented Tungsten Carbide, as the latter represents one of the outstanding developments of recent date in non-ferrous metallurgy. We are interested in the hard metal carbides as a group of related metallic substances and in cemented tungsten carbide as the leading representative of the metallurgy of this group. The literature of this general field is limited, and, bearing this in mind, it seems advisable to attempt to cover the field broadly and to correlate the subject matter, rather than to present a detailed account of any one of its phases. Our annual lecture lends itself admirably to this plan. The quickened interest in cemented tungsten carbide, once its potentialities were recognized, the many sides to the problem of developing the manufacture and use of this new product, and the desire to economize as much as possible in the time of development, have brought many into this work, both in this country and abroad, notably the Osram Lamp Co. and Friedrich Krupp in Germany and the General Electric Co. in this country. It would be presuming too much to attempt to speak too broadly of the present state of the art and science of the hard metal carbides and my remarks arc guided largely by the work done in the General Electric Co., and by our associates in the Carboloy Co. Even here the activities of many in these two groups have centered around the utilization of cemented tungsten carbide, which is outside the scope of this talk. To those whose work is represented in this lecture, it is my pleasant duty to acknowledge their assistance and advice. To Dr. Zay

Jan 1, 1930

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By John Gann

THE following investigation constitutes a brief resume of the more important binary magnesium alloys from the standpoint of metallographic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn.

Jan 1, 1928

By Samuel L. Hoyt

THIS paper gives a short account of plastic deformation as observed in single crystals of zinc, zinc having been selected for the experiments described herein because the phenomena are comparatively so simple and can be studied throughout such a wide range. It is hoped that the paper will serve to show the type of information which studies of single crystals afford and will contribute toward the solution of the general problem of metallic behavior. PRODUCTION OF ZINC SINGLE CRYSTALS The method of Czochralski,1 as modified by von Gomperz,2 was used to produce the crystals studied. The equipment is shown in Fig. 1. Molten zinc is held in a crucible at a temperature which is not far above its melting point, as measured by a pyrometer. A lava disk floats on ,the melt, and is provided with a central hole about 1 mm. in diameter. A glass tube, drawn into a capillary at the lower end, is suspended from a string which is wound up by an electric drive at the speed desired. At the start, the glass capillary is let down into the melt and the hoist is started.. The capillary brings up a small quantity of molten metal with it to a point just above the lava disk. At this point, a jet of hydrogen cools it and causes it to crystallize, with the result that a small crystal forms. As the hoisting is continued, more molten metal is drawn up, in turn to be solidified by the jet of hydrogen. This additional metal continues the growth of the crystal already formed, and a long, cylindrical crystal results. The speed of hoisting used was generally between 0.1 and 0.5 mm. per sec., and the crystals were from 4 to 6 in. long and about 1 mm. in diameter. By varying the conditions, crystals of quite different orientations were obtained and were used in the study of the phenomena to be described.

Jan 1, 1927

C. N. FEnner, New York City (communication to the Secretary) : A possible explanation of some of the' phenomena of amalgamation cited by Mr. Bayliss and others has occurred to me. We know that if, to a quantity of mercury, gold and silver are added until a putty-like paste is formed, and if this mass is spread on a flat surface and pressure is applied, a more fluid portion of the mercury will be squeezed out from the rest, carrying gold and silver with it. The proportion of gold to silver will depend, I think, upon various causes and conditions—the relative chemical affinity which gold and silver have for mercury; the amount of pressure used; the presence of other metals:

Jan 1, 1898

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS. GENTLEMEN: Submitted herewith are the report of the Treasurer for the year 1941 and re¬ports for the same year of the following standing committees: Admissions, Mem¬bership, Papers and Publications, Mining and Metallurgy (Magazine), Library, and Student Relations. These reports present additional details. Membership For the fourth year in succession, mem¬bership reached a new all-time high, level as shown in Table 1. The total at the

Jan 1, 1942

By Frederick Laist, H. J. Maguire

The ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaccs, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper; this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it mas found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first- and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator produces a product that is self-fluxing; in fact, it is possible to produce a concentrate containing more iron than is necessary to flux the silica. Under these conditions, the amount of basic fluxing materials required for the smelting operations became very srnall and the converter slag lost its former value as a blast-furnace flux. For this reason, a less expensive method of recovering the copper, silver, and gold contained in it than smelting in blast furnaces had to be found. It was not feasible

Jan 1, 1921

Feb. 5. Society for Applied Spectroscopy, 6 pm, supper, Tosca's; 8 pm, meeting, Socony-Vacuum Training Center, 63 Park Row, New York. Feb. 6, AIME, Chicago Section, Chicago Bar Assn., 29 S. La Salle St., Chicago. Feb. 18-21, AIME, annual meeting, Hotel Statler, New York. Feb. 19, Michigan College of Mining and Technology, alumni reunion, Skytop Room, Hotel Statler, New York. Feb. 21, AIME, Utah Section, Newhouse Hotel, Salt Lake City. Feb. 28, Bituminous Coal Research, Inc., annual meeting, Edgewater Beach Hotel, Chicago. Mar. 3-7, ASTM, spring meeting and committee week, Hotel Statler, Cleveland. Mar. 5, AIME, Chicago Section, Ladies' Night, Chicago.

Jan 1, 1952

NEW MEMBERS. The following list comprises the names of those persons who became members during the months of July and August, 1913: Members. ALDERSON, VICTOR C., Prest. of Colorado School of Mines :.Golden, Colo. ALLEN, JOSEPH W., Secy. & Treas. International S. & R. Co;, 42 Broadway, New York, N. Y. AMMON, ROBERT, Chief Sampler B. & M. Reduction Wks., Anaconda Copper Min.Co., Great Falls, Mont. BARBER, RAYMOND J., Min. Engr 234 Newbury St., Boston, Mass. BARDWELL, EARL S., Genl. Concen rator Foreman Boston & Mont. Reduction Plant, Great Falls; Mont.

Jan 9, 1913

By R. H. Harrington

THE definition of precipitation-hardening is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening. This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.-Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheat-ing to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (1) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats.

Jan 1, 1936

By Harry L. Washburn, Robert L. Llewellyn, W. J. Halvorsen

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment. JUSTIFICATION FOR COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-range planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and nuclear energy. Coal prices for power plants are still on a Btu (British thermal unit)

Jan 1, 1981

By Charles Clayton

IN connection with certain coöperative work carried on between the Ordnance Department of the U. S. Army, the U. S. Bureau of Mines, and the U. S. Geological Survey during the year 1918, it was the writers' privilege to make metallographic examinations of a great many test bars and other pieces of nickel-steel gun forgings. The material studied came from many different steel plants throughout the country and consisted both of forgings that had been accepted by the Ordnance Department and those that had failed to pass the specified physical tests. In general, these tests require a minimum tensile strength of 95,000 lb. (42,091 kg.), an elastic limit of 65,000 lb. (29,483 kg.), an 18 per cent. elongation, and a 30 per cent. reduction in area. An average chemical composition of the steel studied is 0.38 per cent. carbon and 2.9 per cent. nickel. The steel was of both basic electric and basic open-hearth manufacture. The object of the metallographic work was two-fold: to assist in detecting defects in the steel and, if possible, to suggest remedies for the same; and to obtain as much information as possible in regard to the relation of the microstructure of the metal to its physical properties. The greater part of the investigation was devoted to defective metal that failed to pass the ordnance specifications. Many types and kinds of more or less serious defects thus came under observation, but most of these were due to the attempts by the manufacturer to meet the enormous demand for ordnance steel with more or less inadequate equipment, and were soon remedied. Two defects, the so-called "flakes" or "snowflakes" and a certain "fibrous" or "woody" fracture, were encountered so frequently and were so disastrous to the steel that the greater part of the study was devoted to them. As a result much information as to their nature and their effects

Jan 2, 1919

By Paul Giesecke

SINCE most modem metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. PRINCIPLES OF SPECTROCHEMICAL ANALYSIS In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1944

By K. J. McGrew, J. W. Murphy

Introduction Maximization of profit consistent with environmental protection is the principal goal of new applications development for any conventional or in situ mining technique. Efficient evaluation of all the parameters that contribute to mining costs and production hinges on proper design and evaluation of testing programs and data. The program discussed uses several field and laboratory procedures to estimate ore deposit characteristics and optimize lixiviant compositions. Ore characteristics and lixiviant compositions are then used in a long path leaching test (stream tube test). Stream tube test data are analyzed by mathematical models with computer assistance to predict such wellfield rate parameters as target metal production, lixiviant consumption, and restoration. When these predicted rates are combined with market values for target metals, capital expenditures, prices of lixiviant chemicals, and other economic variables (labor costs, power rates, and licensing fees), an assessment of the relative feasibility of various proposed mining plans is possible. The flowsheet in Fig. 1 illustrates this process. [ ] Field and Laboratory Procedures In general terms, the procedures followed in the evaluation of an in situ leaching application aim at accomplishing: •rapid leaching and maximum recovery of the target metal in a marketable form, •low consumption of lixiviant chemicals, •unquestionably satisfactory restoration of the mined aquifer, and •minimization of capital and operating costs for the above through development of an optimum mine plan. Keeping these goals in mind, the following minimum test program is generally recommended. Geology •Estimate of ore reserves and their variability. •Average disequilibrium value for uranium deposits. •Ore thickness, depth to ore, water level, degree of confinement, and consolidation. •Characterization of quality and quantity of other ore deposit constituents (e.g. sulfide minerals, ion exchange parameters). Hydrology •Single well pump and injectivity test. •Downhole vertical permeability test to compare flow rates of barren and mineralized formations. •Groundwater quality as it may affect licensing, hydro metallurgy, and restoration. Hydrometallurgy • Flask or autoclave tests for optimization of lixiviant parameters and determination of specific reaction rate constants. • Flask or autoclave tests for assessing amenability of lixiviant solutions with ore, consumption of lixiviant, stability of metal in solution contacting ore, and environmentally important species mobilized. • A long-path leach test for modeling the behavior of the lixiviant solution flowing through a long mineralized streamline (stream tube testing). •Metal recovery tests from lixiviant solutions (ion exchange, electrowinning, etc.). •Lixiviant regeneration tests. •Environmental restoration tests.

Jan 1, 1985

By R. D. Pehlke, J. V. Gluck

A study was made of the effect of small additions of metallic solutes on the thermodynamic activity of zinc in dilute solution with molten bismuth in the range 450o to 650°C. The experimental measurements were made in a multielectrode galvanic cell using. a fused LiCl-KCl electrolyte. The activity of zinc in binary solution exhibited a strong positive deviation from Raoult's law and obeyed Henry 's law to at least 0.050 mole fraction. The ternary addition of lead, gallium, or indium increased the activity of zinc. Cadmium or tin additions slightly decreased the zinc activity. Copper, mercury, silver, or antimony caused moderate decreases, while gold strongly decreased the zinc activity. The results are expressed in terms of Wagner's interaction parameter ejZn and a second-order cross-interaction parameter. The interactions for copper, gold, silver, and antimony showed a linear dependence with reciprocal absolute temperature, while the other interactions were essentially independent of temperature over the experimental range. Since tin and antimony decreased the zinc activity, the hypothesis of a purely periodic variation with atomic number was rejected. A semiquantitative explanation was possible with a free-electron model when relative electronegativities were used to express changes in the electron/atom ratio caused by the solute addition. Random solution and quasi-chemical models correctly predicted the majority of the interactions for which binary data were available to apply them. A knowledge of the thermodynamic interactions in liquid (and solid) metallic solutions is of considerable theoretical and experimental interest in the formulation of quantitative thermodynamic relations for metallurgical processes. The approaches to defining the interactions may be either phenomenological (i.e., "What mathematical function adequately describes observed behavior and permits extrapolation to new situations?") or theoretical, such as a specific model

Jan 1, 1968