Search Documents

By Stanley C. Herold

TWENTY-FIVE years ago no distinction was made between water wells and oil wells except in the nature of the fluid produced. Water wells usually showed no decline in their rate of production; when oil wells showed decline something in the manner of handling them was considered wrong. Both water and oil were believed to be subject to the same physical laws in their underground movement toward the wells. Today a sharp distinction is made between them. Whereas water exists alone in the porous formations at depth, oil is usually accompanied by gas. This mixture does not behave as a liquid alone. It is a frothy, seething mass of foam which approaches and enters the wells. Different physical laws come into play. Twenty-five years ago attention was directed entirely to the well itself; today the well is accepted as a mere hole in the ground, a hole to be equipped properly for efficient service, yet without any value whatever unless it is backed up by a sufficiently prolific reservoir. Then, we were concerned with wells alone, 3000 ft. in depth; now commercial wells and their reservoirs are 10.000 ft. deep. Petroleum engineering concepts have necessarily therefore undergone a change in this last quarter century. What are they today?

Jan 1, 1937

By W. H. Yarroll

This paper presents a general discussion of the utility of the statistical technique known as multiple correlation, and gives three specific examples of its application. The first demonstrates the most simple form, or straight-line, multiple correlation. The other two demonstrate multiple correlation analysis in best-fitting third-degree parabolas. With the increasing availability of digital computers, the method becomes entirely feasible where heretofore its use was impractical. The advantages of the method are discussed, and curves are presented which were developed by computerizing the regression equations developed in the examples. The method described in this paper is for use with complex systems, and the examples given are complex metallurgical systems. This subject falls under the general classification of cybernetics, which is defined' as "the science of control and communication, in the animal and the machine." Machine, in this case, can include chemical and physical processes which take place within machines and processing equipment of all kinds. The classical approach to scientific investigation has been the construction of simple models and the changing of variables one at a time. This method is wholly inadequate for obtaining useful information from the complex systems of modern technology including many of our flotation and hydrometallurgical processes. Cybernetics offers the method by which complex systems which have been implemented as an art in the past can now be analyzed with all the discipline of a science. Mathematical techniques for achieving multiple correlation analysis have decided advantages over some of the other statistical methods.2-4 Multiple correlation does not require a series of experiments that have been rigidly planned as do many of the other statistical methods. For this reason, it can be used effectively for interpretation of information from op- erating plants, where planned experiments are impractical, as well as for laboratory experiments. First-degree multiple correlation has been used for many years, and was useful, but limited to linear or nearly linear relationships. The technique described in this paper provides a method for analyzing systems which may be non-linear. This particular technique is multiple correlation analysis in best-fitting third-degree parabolas. It is quite possible that lack of reference to the technique has been due to the overwhelming mass of computations it requires even for relatively simple problems. With the advent of computers, however, its use has become entirely feasible. For the benefit of those who may not be familiar with the subject, it might be well to pause at this point to discuss multiple correlation analysis — what it is and what it achieves. To go back to the old familiar fitting of a set of points with a best-fitting straight line by the least squares procedure, it is conceded that this a good method where there is only one independent variable influencing the dependent variable under consideration, and providing that the relationship is linear. In most fields of investigation, however, there are usually a number of factors exerting important influence, and they frequently bear relationships with the dependent variable other than straight line. Under these conditions, it is easy to see how misleading a simple correlation study might be. Multiple correlation can be used for any number of variables. Within the experience of the writer, this technique has been used to establish regression equations for determination of carbon rate, burden permeability, and production rate on iron blast furnaces, production rate on open hearth steel furnaces, life of molds for steel ingots, rolled steel tensile strength and various defects in rolled products, the performance of ore dressing equipment, and optimization of extractive metallurgical process variables. The discovery of mathematical correlation does not prove, per se, true cause-and-effect relationship, but simply establishes a hypothesis. If the regression equation can be used to make successful predictions of what will happen with future arrays of independent variables, then one can feel reasonably assured that true cause-and-effect relationships have been discovered.

Jan 1, 1968

James W. Malcolmson died suddenly on Dec. 26, 1917, at Kansas City, Mo., where he had made his home for the past ten years. He was born at Dover, Kent, England, on Oct. 6, 1866. He graduated from the Royal School of Science, London, England, in 1889, and almost immediately after graduation came to Mexico, accepting a position with the Michoacan Railway and Mining Co., as mining and mechanical engineer. His work in the mining profession was carried on principally in Msxiac and the United States. • In 1888, he married Katherine Haden Krause, of Woolwich, Kent, England, and leaves, besides his wife, five sons and one daughter. During Mr. Malcolmson's long and successful career as a mining engineer, he was connected with the following companies: from 1889 to 1893, with the Michoacan Railway and Mining Co., as mining and mechanical engineer; from 1893 to 1898, in various capacities with the Kansas City Smelting & Refining Co.; after the consolidation of the Kansas City Smelting & Refining Co. with the American Smelting & Refining Co., he remained as manager of the mining department in Mexico of the American Smelting & Refining Co. until 1902. In 1902, he located in El Paso, and took up the practice of his profession as a consulting engineer. While there, he was consulting engineer for the famous and rich Pedrazzini mines at Chispas, in the State of Sonora. He was instrumental in organizing the La Republics mine in Chihuahua, and for a time acted as consulting engineer for the property. He remained in El Paso until 1907 and then moved to Kansas City and became associated with the United States & Mexican Trust Co., as consulting engineer. In 1909, he became connected with The Lucky Tiger Combination Gold Mining Co., as its consulting engineer, and continued in this connection and in the general practice of his profession as consulting engineer until his death.. His general policy in connection with the Lucky Tiger company was always a progressive one and the success of the enterprise can be largely attributed to him and his good judgment. Mr. Malcolmson contributed several articles to the Institute at different times, one of them being on the ore deposits of the Sierra Mojada Mining District, in 1901. Much of his work was in Mexico, and during his long residence in that country he acquired a very thorough knowledge of the Mexican people and their customs. During the revolution, from 1910 to 1916, this knowledge was of great value in connection with his work for the Lucky Tiger company, and often assisted greatly in keeping the property going. Mr. Malcolmson was one of the very widely known men in his profession; he was everywhere held in the very highest regard, and his position among men in the mining profession was an enviable and honorable one. At the time of his death, besides being consulting engineer for the Lucky Tiger company, he was interested in mines in the Miami zinc fields and was acting as consulting engineer for two of the operating properties there. He invested to quite an extent in real estate when he moved to Kansas City in 1907 and his investments in this line proved successful.

Jan 1, 1920

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand. The new installation employs 24 in. x 10 ft, 9-in. Simplex double-pitch spiral classifiers for feeders from the bin bottoms to the ball mill scoop boxes (fig. 1). These units are arranged with straight tanks and are driven by 5 hp motors through a U. S. Vari-Drive to provide a 4 to 1 speed ratio. Each bin discharges through a chute into the rising side of the spiral. The flushing characteristic of the material from the bottom of the bin is utilized to maintain a steady feed. A small amount of water tapped into the bottom of the bin insures uniform feed to the classifier. Excess clear water drains over the weirs. Feed rate to the mills is controlled by the variable-speed drives. The feed delivered by the spiral at a given speed setting is relatively dry, uniform, and steady, and as such is easily controlled by the operator. The classifiers are set on a pitch of 5 in. per ft and have a sand-raking capacity of from 8 to 32 tons per hr. It is believed that the solution of this problem offers possibilities for the storage of deslimed rod-mill sands and other similar products of the industry.

Jan 1, 1951

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand. The new installation employs 24 in. x 10 ft, 9-in. Simplex double-pitch spiral classifiers for feeders from the bin bottoms to the ball mill scoop boxes (fig. 1). These units are arranged with straight tanks and are driven by 5 hp motors through a U. S. Vari-Drive to provide a 4 to 1 speed ratio. Each bin discharges through a chute into the rising side of the spiral. The flushing characteristic of the material from the bottom of the bin is utilized to maintain a steady feed. A small amount of water tapped into the bottom of the bin insures uniform feed to the classifier. Excess clear water drains over the weirs. Feed rate to the mills is controlled by the variable-speed drives. The feed delivered by the spiral at a given speed setting is relatively dry, uniform, and steady, and as such is easily controlled by the operator. The classifiers are set on a pitch of 5 in. per ft and have a sand-raking capacity of from 8 to 32 tons per hr. It is believed that the solution of this problem offers possibilities for the storage of deslimed rod-mill sands and other similar products of the industry.

Jan 1, 1951

By Claudia Gasparrini

Silver occurs in nature in major, minor and variable amounts in a very large variety of minerals and in several mineral species in the same ore. Because these minerals may respond differently to the same flotation or leaching agents, detailed studies to establish the correct silver mineralogy become essential for optimum recoveries in those situations where the silver is treated as a primary product. On the other hand, fine grain sizes, which often affect gold recoveries, are not generally as critical in silver metallurgy, due to the lower market price which allows for more of the element to remain In the tailings before incurring in economical losses.

Jan 1, 1984

By P. T. Carter, A. B. Murad, H. B. Bell

N. A. Gokcen (Michigan College of Mining and Technology, Houghton, Mich.)—The activities of silica, represented in Fig. 5 for the systems MnO-SiO2 and CaO-SiO2, are in disagreement with the established binary phase diagrams. At Ns102 = 0.50 in MnO-SiO2, and at Ns102, = 0.65 in CaO-SiO2, each binary system is saturated with respect to silica at 1550°C, and therefore as102, is unity in each case. The curves for as102 (FeO-SiO2) and as102, (MnO-SiO,) should nearly co-

Jan 1, 1953

By John P. Cosgro

THE increasing use of internal furnace-boilers for mining power-plants (doubtless due to the facility with which they may be installed by reason of their portability; the fact that they require no masonry setting, cast-iron fronts, buck-stays, etc., and practically no foundation; and the successful maintenance of their claim to equal and even superior economy, as compared with boilers of other types) warrants this description of a method of remedying an injury which may occur, to such a furnace, even though it satisfies the requirements of the formula adopted by the U. S. Board of Supervising Inspectors of Steam Vessels.2 I refer to the sagging and deformation which may result from overloading the boilers for a considerable period-say, several days. This is sometimes unavoidable under the exacting conditions of continuous day-and-night service, and (in spite of all rules and precautions, the occasional careless or unskillful work of attendants. Such a trouble is by no means unknown on shipboard, where this type of boiler is so largely employed. In the case here described, two Morrison suspension-furnaces, of half-inch steel, 14 ft. long and 45 in. in mean diameter, with ? dry-back ? boilers, were necessarily operated somewhat beyond their rated -normal capacity for several months, while a third similar unit was -in process of installation, and during this period, though the boilers were kept perfectly clean, heat seems 'to have been generated slightly faster than it was absorbed by, the water in the boilers. The corrugations of this.

Mar 1, 1905

By J. D. Price, W. M. Bertholf

Making maximum possible use of available equipment and material, CF&I placed a high-efficiency, high-capacity washery unit in the existing buildings to gain simplified operation, reduced manpower requirements, raised efficiency, and boosted production. THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers. In the late 1940's it became evident that something would have to be done to keep the washery abreast of progress at Pueblo and other washeries. Coal requirements were nearly two and one-half times the original requirements of the 120 small ovens, as additional ovens had been built in 1930, 1938, and 1945, whereas no additional coal washing capacity had been added since the 1936 modifications. Much of the equipment, moreover, had seen better days. One answer to the problem was to build a new and completely up-to-the-minute plant, with sep- arate sections for coarse, medium fine, fine, and very fine coal. On the other hand, it might be financially more profitable to place a high-efficiency, high-capacity unit in the existing buildings. The washing problem at Pueblo is not unique, but it is approached differently. There are no established specifications for coke ash and sulphur. The plant is operated on the principle that if it is more economical to wash it out than to slag it out, wash it out; otherwise, send it on to the blast furnaces. With coals at the Pueblo plant costing what they do, the benefits of washing at a low gravity are questionable. Hence the primary problem is to eliminate the high-ash components and retain all the low and medium-ash components. Sulphur is no problem at all, averaging 0.6 pct in the coke. Since a good proportion of the free impurity in the coals is as large as the coal or bone or larger, it appeared that it would be safe to go to jig washing and discontinue crushing the coal before washing, as had been the practice with the tables. This would boost the throughput. It might also decrease manpower requirements and washing costs considerably. It was assumed at the start and has been demonstrated in the first year of operation that a jig will do as well on the fines as the tables had been doing. It would not be necessary to discount any gains due to increased efficiency in washing the coarse material because of incapacity to wash the fines. By washing at —2+0 mesh it would be possible to dewater, by screening, a considerable tonnage satisfactorily, for example, at —2 + % or —2 + l/4, and then crush it in a hammer mill. The —?+20 could be dewatered in centrifugal driers and the remain-

Jan 1, 1955

By Burt Hartmann

The nation's ever-expanding construction and mining activity has placed an increasing demand upon engineers and geologists to design and construct stable slopes in earth materials-soil and rock. Man's attempt to handle these slope stability problems has been based primarily on practical experience and the resulting theories formulated to explain the phenomena. Too many instances occur when man is faced with a slope stability problem that has not yet been experienced and doesn't lend itself to solution by any existing theory. At this point he must extend himself in using his engineering judgment to arrive at a reasonable and safe design. As past experience has shown, all of the "safe designs" are not really safe. Sometimes they result in embarrassing failures. Measurements provide the key to understanding and controlling natural phenomena. We cannot hope to gain control of the slope stability problem until we understand the causes of slope failure, their behavior with respect to time and their relative magnitudes. Measurements required for an adequate definition of any slope problem must be of the highest reliability because of the importance of decisions which must be based on them. For this reason, direct measurements of movement, shear strength, water pressure, etc. of the unstable mass are preferable to indirect measurements of other physical properties. Movement instruments which can be positioned inside of the slope mass (within boreholes) are among the most useful in diagnosis and/or monitoring of slope movements. The higher the sensitivity and il-measurement precision possible with borehole instruments, the quicker the required information can be obtained and the more exactly may hazardous conditions be observed. A high density of measuring points in a single drill hole is deemed essential for diagnostic purposes. Behavior gradients may thus be obtained. The Pressure Meter (Fig. 1) can be used to measure a relative strength

Jan 1, 1968

By Ervin E. Underwood

IT has been recognized for many years that dis-persed particles have great value in raising the creep resistance of metallic alloys. In fact, some of the most successful high-temperature alloys owe their superiority to this factor above all others. A recent observation by Glen1," indicates that even better high-temperature resistance to deformation results in alloys capable of two successive precipitation reactions. The ramifications of this finding are of great interest. Unfortunately, our understanding of the reasons for such notable improvements has not kept pace with technical developments. In an effort to uncover some of the basic facts governing strengthening by particles, a program was initiated at the Battelle Memorial Institute with the primary goal of comparing creep strengths in single-phase and two-phase (precipitating) alloys. The effects of precipitation from solid solution on the creep properties of alloys are generally such that the resistance to creep is increased. However, if alloys are heat treated to different degrees of hardness before creep testing, it is often found that those possessing the maximum hardness initially do not necessarily have the maximum creep resistance. Depending on the stresses and temperatures involved other structures may prove more desirable. Considerations of the above nature indicate the importance of defining the initial state of the alloy. Here, it was decided to start with quenched single- phase alloys in which precipitation and creep deformation proceed concurrently. Equipment and Experimental Procedures Preparation of the Specimens—Four 25 lb ingots were prepared from 99.999 pct Cu and 99.996 pct Al to compositions of 1, 2, 3, and 4 wt pct Cu. Spec-trographic and chemical analyses are listed in Table I. After heat treatments and intermediate reductions, the alloys were cold rolled to 1/8 in. thick sheet. The final cold reductions amounted to 50, 40, 20, and 10 pct for the 1, 2, 3, and 4 pct Cu alloys, respectively. The specimens for creep testing were machined into tensile flats 7 in. long, 3/4 in. wide (at the shoulders), and 1/8 in. thick. The reduced sections were 1/4 in. wide and 21/2 in. long. After heat treatments at 540°C to an ASTM grain size of 1 1, the specimens were quenched into water at room temperature, then electropolished in a glacial acetic acid and perchloric acid solution. The gage marks were Knoop impressions placed 2 in. apart on the reduced sections. Blanks of 1 x 1 in, were cut from the same sheets for the age hardening runs and were given the same grain size heat treatments. The specimens and blanks were stored in a refrigerator at —40°C until needed for testing. Creep Measurements—Creep tests were conducted in a constant temperature room which was maintained at 26° ±1°C. A split-type, hinged, vertical-tube furnace was mounted on a horizontal track so that the specimen could be enclosed suddenly. Thus, it took about 15 min for the specimen to come within 5°C of the test temperature. The temperature variation along the specimen was controlled to about

Jan 1, 1958

By John V. W. Reynders

Our entry into the World War suddenly brought home to us in a startling way the vital importance of manganese. Since the war, much has been written and said upon the subject of manganese and a great deal of time and money have been spent in attempts to find an adequate substitute for this metal in the manufacture of steel; none has been found. It is true that ways are known by which it is possible to make small amounts of good steel without manganese, but taking into consideration the diminishing quality of iron ores and fuels as well as the increasing exaction of specifications for finished products, it may safely be assumed that, high-grade manganese ore will be more and more a necessity in the production of steel as time goes on. Taking world resources as a whole it may be well to point out that the problem of obtaining needed supplies of manganese from a strictly commercial viewpoint is now less serious than it was before the war. Formerly it was feared that world resources of high-grade manganese ore might be exhausted in a relatively short time, but, largely as a result of the stress laid upon the importance of manganese during the war, the world's available supply of high-grade manganese ore has been greatly augmented by new discoveries and fuller development of previously known deposits. Sources of Production Russia alone, of countries producing the major part of the world's stee1, has within its geographical boundaries sufficient manganese to supply its needs. The domestic production of England is inadequate and English requirements for high-grade manganese are supplied principally from India. France also draws largely upon India, as it depends upon foreign sources of supply except with respect to a small tonnage of silico-manga-nese and silico-spiegel produced in the Hautes-Pyrénées. Germany and the United States likewise depend upon foreign sources of high-grade ore, though each possesses comparatively large reserves of ferruginous manganese ore and manganiferous iron ore. At present the world demand for high-grade manganese ore is met with ease by the production of Russia, India, Gold Coast and Brazil.

Jan 1, 1927

By BION J. ARNOLD

WE can, I think, rightfully claim, irrespective of our faults, that engineers must, in order to last as engineers, possess the qualifications of integrity, stead- fastness of purpose, ability to think straight, and to apply these qualities consistently and continually in their everyday work. All engineers know this, most of them conform, and in order to drive it home I might, if 'clothed with proper authority, preach to you at length, but I shall not take the chance. So I only want to make a suggestion or two to the young engineers. Have an ideal and work toward it. You will have your disappointments and your temptations but keep your record clean, and if anyone says you are foolish or ugly, or homely, or that you need a guardian, take the criticism with a smile, for he may be able to prove his contention; but if he attacks your integrity, strike at once and fight hard, for he has assailed not only your character but your principal asset as an engineer.

Jan 1, 1929

By Charles R. Keyes

I. Introductory,.......... 185 II. Hypotheses oF the Origin of OzaRk Ores..... 186 1. General Considerations........ 186 2. Schmidt-Leonhard and Gage View...... 187 3. Jenney Opinion.......... 187 4. Posepny Idea,.......... 188 5. Winslow-Robertson Hypothesis....... 188 6. Branner Proposition......... 189 7. Keyes Statement.......... 189 8. Van Hise-Bain Theory........ 190 III. Requirements of an Adequate WoRking-Hypothesis,... 190 IV. GeneRal Geotectonics of the OzaRk Region.... 192 1. Salient Aspects.......... 192 2. Geologic Formations......... 192 3. Character of Faulting...192 4. Extent of Flexing......... 193 5. Unconformity Inequalities....195 6. Warping of Strata...195 V. Classes of Ore-Deposits... 196 VI. Vadose ORe-ConcentRation,........ 197 VII. GeogRaphic DistRibution of the Ore-Bodies,... 199 VIII. Relation of ORe-Deposit to Geologic Structure... 201 1. General Occurrence of Ore-Bodies in Basins.... 201 2. Deposits of the Central Missouri District..... 203 3. Deposits of the Southwestern Missouri District.... 203 4. Deposits of the Northern Arkansas District... 305 5. Deposits of the Southeastern Missouri District.... 206 6. Synclinal Ore-Deposits of Other Districts.....207 7. Significance of Ore-Troughs in Prospecting... 209 8. Origin of the so-called Synclines,...210 9. Significance of the Cross-Bars of Joplin..... 213 10. Relation of Ore-Run to Ancient Relief-Features,... 215 IX. Direction of GRound-Water Circulation..... 216 X. VeRtical Range of Workable Ore-Bodies,... 218 XI. Oscillation of Ground-WateR Level...... 219 XII. Relations of Ore-Bodies to Lithoclasic Features,.. 220 XIII. PRimaRy Source of Ore-Materials,...... 220 XIV. Zone of Ore-Enrichment,......... 222

Jan 1, 1910

By Lewis E. Dr. Young

MINING engineers in the United States understand that mining conditions in the British coalfields are much more difficult than in most of the mines now being operated in the United States. We realize also that in the near future we must face some of these same difficult problems. Early Mechanization The progress made in mechanical loading in the United States is the result of a long struggle in many coalfields to mine with power tools safely and to increase output per man-shift. Attempts to use power to loosen coal and to transport broken coal in the U. S. may be said to date from the Stanly Header, or Entry-Driver brought from England in 1888. The principle of this boring machine was used in the McKinlay Entry-Driver, almost continuously used in the U. S. since 1920. Since 1888 experimental loaders, scrapers, and conveyors were installed with more or less success. Beginning in 1918, considerable progress was made with mobile loaders, and in 1920 the first wage agreement for the operation of mechanical loaders was made in Indiana. In 1923 the Pocahontas Fuel Co. loaded nearly 1 million tons of coal using 23 Coloders. Labor Policy The United Mine Workers of America have never officially opposed the Mechanization movement. On December 10, 1945, in a statement before the House of Representatives Labor Committee, John L. Lewis said, regarding the policy of the United Mine Workers of America: "We have welcomed progress; we have welcomed machines. We have told our people that they had to accept that condition; that it was the process of progress, and that they would have to take their chances." Recent Development In 1951 about 71 pct of the tonnage mined underground was mechanically loaded. Over 4000 shuttle cars are in service and it is estimated that much more than half of the tonnage loaded underground is produced by trackless mining. In 1947 roof-bolting was introduced extensively and it is estimated that more than 2 ½ million bolts are now being used per month in about 600 mines. The use of roof bolts has permitted the more effective and safer use of loaders and shuttle-cars. Continuous Mining The McKinlay Entry-Driver could have been used for continuous mining, but for many years it was used only .for entry driving. In 1946 the Silver machine was developed in Colorado, and in 1947 this was acquired by the Joy Mfg. Co. and called the Joy Continuous Miner. Other types of combination mining-loading machines which eliminate drilling and blasting operations are the Marietta Miner, the Colmol, the Lee-Norse Miner, the Junior Miner, the Goodman and the Konnerth machines. There are several other types in the process of development. Probably by January 1953 there will be about 250 continuous miners in operation in the U. S. Payment of Mine Labor One of the most important problems in mechanizing was the establishing of rates of pay that would be attractive to the best men. Prior to the installation of mobile loaders the hand loaders and cutters have been paid by the ton. It was felt that a system of a day's pay should be established and that piece and tonnage rates should be abolished completely. Without exception, all coal loaded in mines equipped with mobile loaders is prepared and loaded by men paid an hourly rate. Trends in Mining Research There are two diverse approaches in coal production research; to try to design a mining machine to fit current methods, or to adapt mining practice to take advantage of proven machines. A great deal of credit must go to the mine operators who have been enterprising and dynamic enough to use available equipment intensively and to discard it as soon as an improved or new machine is available. Effect of Changing Markets Formerly there was an important demand for lump and prepared coal in the larger sizes for domestic use. The use of bituminous coal for house heating has decreased so that not more than 19 pct of the annual tonnage goes to retail trade, only 12 pct is used by the railroads, and much of the retail and most of the railroad coal is in stoker size. As a result of this decline in the market for coarse coal most of the large mining operations have crushers installed in the tipples or preparation plants. Mass production at the face requires increased preparation facilities. Another important trend is in connection with complete seam mining with mechanical loading. In many mines where the immediate roof is apt to fall with the coal no effort is made to separate roof material from coal prior to

Jan 1, 1952

By W. H. Herrnstein, J. B. Clark, E. C. Utley, A. J. McEvily

The ratio of the endurance limit (10' cycles) to tensile strength of age-hardened aluminum alloys is approximately 0.3, whereas the ratio for annealed alloys is about 0.5. The lower value for the age-hardened alloys has been associated with the instability of coherent precipitate during cyclic loading, but it has not been definitely established whether this instability is due to overaging or reversion during cyclic loading. The results of the present investigatzon support the reversion viewpoint. In this work specimem of 2024-T4 aluminum alloy were aged for 16 hr at 150°C after cycling for 10 pct of the life at 25.000 psi. These specimens were then tested to failure and exhibzted a marked increase in fatigue life. It is proposed that during the early stages of fatigue in this alloy dislocations cut through the coherent precipitate and bring about the reversion of the precipitate. Subsequent aging at 150ºC induces reprecipitation in the precipitate-free zones so that the weakened regions are strengthened and the fatigue life is extended. It Is recognized that the fatigue strengths of precipitation hardened aluminum alloys are unusually low relative to their tensile strength.'-= This feature is illustrated in Fig. 1 where it can be seen that age-hardened alloys have lower fatigue ratios (the ratio of the fatigue strength to the tensile strength) than those in the annealed or cold worked state. Further, as shown in Fig. 2, the more an alloy is dependent upon precipitation hardening for its total strength, the lower is the ratio of the fatigue strength to the tensile strength. This state of affairs has been associated with an instability of the metastable metallurgical structure of precipitation hardened aluminum alloys during cyclic loading. Evidence2 in support of this view is that the fatigue ratio increases in these alloys as the test temperature is lowered, thereby indicating that thermo-mechanical instability, rather than some other factor such as a non-uniform distribution of precipitate, is the factor responsible for the low fatigue ratio at room temperature. Two mutually exclusive proposals have been ad- vanced to account for this instability. Hanstock has proposed that overaging takes place during cyclic loading, and in support of this view, Broom et a1.2 have indicated that an overaging process might be promoted by the large numbers of vacancies which are created during cyclic loading. The creation of vacancies by radiation4 has been shown to lead to rapid overaging. Hanstockl obtained visual evidence of overaging in an aluminum alloy after cyclic loading, but in this instance it has been pointed ou? that because of the high frequency used (60,000 cpm) the observed effect may have been due to normal high temperature precipitation around energy dissipating cracks. Efforts to discern visual evidence of overaging in this alloy at lower test frequencies were not successful.3 The alternative postulate3 is that reversion takes place during cyclic loading and leads to localized soft spots at which fatigue cracks are readily initiated. Evidence for this process has recently been provided by Polmear and Bainbridge5 who demonstrated metallographically that regions depleted of precipitate were created during cyclic loading of an aluminum alloy. Inasmuch as precipitate particles bordering the depleted region had not grown in size, it was concluded that the solute atoms which had constituted the missing particles had gone back into solution. No mechanism for the reversion process was presented. The present study was undertaken to investigate further the conditions leading to instability during cyclic loading, and to determine whether reversion or overaging had taken place as a result of cyclic loading. BACKGROUND AND TEST PROCEDURE In order to differentiate between the processes of reversion and overaging, rest periods at an elevated temperature, which ordinarily would insure additional precipitation, were used in this investigation. It was expected that after a period of cyclic loading an elevated temperature rest period would result in a decrease in the remaining life of the specimen if overaging were occurring during cyclic loading, whereas in the case of reversion, reprecipitation would occur and the fatigue life would be extended. Such an expectation is based on the assumption that the crack-nucleation phase is a significant portion of the total fatigue life, and that such a treatment is of influence in the crack-nucleation stage and is relatively unimportant thereafter.

Jan 1, 1963

By J. H. Brophy, A. L. Prill, H. W. Hayden

An error lzas been found in the conventional way of determining the time exponent of linear shrinkage for the solution-precipitation stage of liquid-phase sintering. Large amounts of shrinkage due to initial rearrangenzent result in erroneously low exponents and tni si dentification of the rate-controlling process. Two alternative, mathematically correct, methods of calculation are applied to existing data on Fe-Cu, WC-Co, and Tic-Ni-Mo. This results in reidentifi-cation of the rate-controlling process and somewhat better agreement with related data. In each case the solution-precipitation process is solution-controlled and not diffusion-controlled. THE liquid-phase sintering process has been the object of a considerable amount of research for many years. Linear shrinkage vs time data at various sintering temperatures have been used recently in an attempt to identify the prevailing mass-transport processes in a number of metallic and nonmetallic systems. There is an analytical error inherent in the methods previously used for handling data during the "solution-precipitation" stage of shrinkage which must be recognized before the correct rate-controlling processes can be determined. It is the purpose of this paper to show how the error has affected previous conclusions and to suggest corrections. A number of mechanisms have been proposed to explain experimental observations during sintering in the presence of a liquid phase. The earliest of these is due to Price, Smithells, and williamsl who attributed the observed growth of the solid phase to the simultaneous solution of smaller particles and growth of larger particles. From the work of Lenel et al.2,3 and Gurland and Norton4 has come the suggestion that the liquid-phase sintering process may be divided for analysis into three steps: 1) rearrangement upon formation of the liquid phase; 2) solution and reprecipitation of the solid phase in the liquid; and 3) "coalescence" or a final stage of sintering, characteristically slower than the solution-precipitation process. The sequence of steps is shown schematically in Fig. 1. Kingery5 presented a thermodynamic and kinetic analysis of the first two "stages" of the liquid-phase sintering process in which the functional dependence of lineal shrink- age on time at temperature was used to identify the rate-controlling mass-transport process. Table I summarizes the time dependences and processes considered by Kingery.5 This method of data presentation has been employed by Kingery and coworkers for Fe-CU,6 WC-Co, and a number of nonmetallic systems," and bv Whalen and Humenik for Tic-Ni-Mo and Fe-cu.8 In each of these studies, the rate-controlling step during the "solution-precipitation" stage was identified from the slope of the curve in that stage on a logarithmic plot such as Fig. 1. However, in all of the previous studies, at a certain composition, relatively large amounts of shrinkage due to rearrangement preceded the solution-precipitation stage. Under these conditions, the larger the amount of rearrangement shrinkage the

Jan 1, 1965

By Tell Ertl

An annual invitational address by an outstanding man in mining, geology, or geophysics who has contributed significantly to the progress of technology in these fields. IN 1954, the first year the award was conferred, Fred Searles, Jr., remarked, "The earlier years are the easiest." In this, the second year, it was easy to choose the outstanding mining engineer. Our conferee this year has been destined to mine. He comes from pioneer stock, and though a son of the American Revolution he is most proud that all four of his grandparents came to the Jordan River Valley of Utah the "first summer," which all Utahns will recognize as 1847. At the time of discovery of high-grade ore in Bingham, his grandfather, Archibald Gardner, had a crew of men getting out saw timber in the area. The first claim staked in Bingham Canyon was named the Jordan, and Bishop Gardner was the colocator of the claim as well as the man to record it. E. D. Gardner was born in West Jordan, Utah, in view of Little Cottonwood Canyon, the site of the Emma Mine. Park City in the Wasatch Mountains a few dozen miles to the east, and Tintic, not much further to the south, were developing their vast ore-bodies throughout his youth. As a boy he was near the present Midvale metallurgical area and could see the Lark and Bingham Canyon mine dumps and imagine the mining activities at Tooele, Ophir, and Mercur just over the nearby Oquirrh Range. He was 11 years old when the first car of copper ore was shipped from Bingham Canyon. It was not surprising that he attended the University of Utah and graduated with an engineer of mines degree. Five years with the Utah Apex in Bingham Canyon as chief engineer and assistant superintendent completed his training for the 44 years of unselfish and lightly rewarded service he was to give the mining industry as a Government engineer. All of us in mining are familiar with the great work he carried on and directed during the genera- tion he supervised the Southwest Experimental Station at Tucson. He has written scores of papers and books. His observations and experiments on drilling and blasting have led to the important improvements in this field during the past quarter century. Whereas those of us who consider ourselves widely informed about underground metal mining methods make hasty trips through a half dozen or dozen mines a year, our conferee has visited them all—not only the metal mines, but also coal and hundreds of nonmetallic mines, in the United States, Canada, Latin America, and overseas. His keen observations and analytical mind have resulted in an encyclopedic knowledge of mining and mines. His improvements in mining technology have been steady and predictable. His elucidation of mining problems to the many young engineers that have come under his guidance have made them grow strong and useful to his industry. When he chooses to stop, his influence will continue to expand and prosper because of the inspiration and dedication he instilled in so many of us. The profits from his ideas have been distributed throughout the mining industry. He has remained a technical man who felt that he could serve the mining industry best as a Government engineer. But he is the staunchest advocate of the belief that the public should gain from his work through private industry. This is not the first recognition E. D. Gardner has received. The Department of the Interior awarded him the coveted Medal for Distinguished Service in October 1949, and he received the Engineering & Mining Journal's Salute in March 1951. His friends who are presenting him the Daniel C. Jackling Award today know this great mining engineer simply as "Ed" Gardner.

Jan 1, 1956

By George B. Lee

During the two years in which the new reduction-works of the Copper Queen Consolidated Mining Co. have been in operation at Douglas, Ariz., there has developed a remarkable condition in regard to the corrosive action of the water used to cool the jackets of the blast-furnaces. Were it not for the many contradictory features, it might pass as one of the unavoidable troubles due to the composition of the water. This water, obtained from wells 600 ft. deep, is also used in the steam-boilers, and its composition, as shown by the following analysis, does not indicate the presence of any ingredient which would explain the corrosion: Grains Per U. S. Gal. Silica,...........0.861 Iron oxide and alumina,....... 0.223 Calcium carbonate,....... 0.261 Calcium sulphate,................. Magnesium carbonate,........... Sodium and potassium sulphates,..14.850 Sodium and potassium chlorides,.9.732 Sodium and potassium carbonate, . 6.482 32.409 The jackets are made of inner plates 0.5 in. thick and an outer plate # in. thick, with 3/8-in. stiffeners between the inner and outer plates. In from 10 to 12 months the inner plates have been reduced by corrosion to a thickness of from + to & in., while the outer plate in the same time is reduced by less than 1/16 in., and the stiffeners show very little corrosion. The plates are pitted and eaten away in some places more than in others. There is practically no scale found on the jackets, but when cleaned considerable iron oxide is found in the bottoms. With an action so marked, serious trouble would be expected in the boilers, but, on the contrary, a recent inspection by a

Jan 1, 1908

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944