Search Documents

By Edward A. Sayre

In shaft sinking for cod mines, the cost item greatly influences the method adopted. This holds true especially when soft material must be traversed. The average life of a coal mine is short. This is due either to the limited area of the coal basin or to the great expense of maintenance and haulage underground when the entries are extended a considerable distance from the hoisting shaft. Therefore, the engineer in opening a coal mine is confronted with the fact that the cost must be kept within certain bounds else the venture will prove unprofitable. For this reason he may be prohibited from adopting certain safe, but expensive, methods that are used in sinking caissons for foundations, driving transportation tunnels, or other work of permanent construction. A common method of sinking through difficult ground employs the aid of a steel shoe pushed ahead of the shaft timbers. Another is the drop-shaft method. These two methods were used in sinking the main shaft and the air shaft of the Eagle No. 3 mine, at Des Moines, Ia., and the following data show the relative success and cost of the two methods of sinking under the same conditions. A drill log of the material to be penetrated was as follows (see Plate 1, Fig. 1): Thickness, Total Depth, Ft. In. Ft. In. Drift................................... 38 38 Sand..................................... 2 40 Drift.................................... 2 6 42 6 Jointed clay.............................. 5 6 48 Drift, firm............................... 10 6 58 6 Clay, with sand streaks.................... 3 61 6 Sand.................................... 12 73 6 Shale, with two thin beds of coal and thin strata of rock......................... 86 6 160 Rock.................................... 5 165 Coal..................................... 3 9 168 9 Main Shaft Sunk by Steel-Shoe Method This record shows the first 73 ft. to bc of drift material, the lower 12 or 15 ft. of which was sand. The remaining 92 ft. to the coal was shale and rock, and offered no trouble in sinking.

Jan 1, 1917

The officers and staff of the Petroleum Division are the servants of the members, and to the extent that the wishes of the members are made known and are practicable they will be carried out. The tentative plans outlined here are in general accord with previous custom, but modified by suggestions received recently from various members. The advice of all members is solicited, and it is hoped that the general expression on matters of policy can soon be facilitated by circulation of a questionnaire. Plans for two mid-year meetings of the Petroleum Division and for participation in the annual meeting at New York were inaugurated at the last annual meeting and are being carried forward as rapidly as possible in the belief that an early start will increase the possibility of finding the best available program material and permit the careful preparation, review, editing, and advance discussion of papers. While a number of papers have already been solicited, both members and nonmembers are hereby invited to submit additional papers, with the assurance that such papers will be given just as favorable consideration as the papers that have been requested. Mid-year meetings will be held at about the same time both in the Mid-Continent and California. The time will be selected if possible to coincide with the visits of President Lovejoy, who expects to be in California the last of September and in Texas early in October. Fort Worth, Dallas and Austin have been suggested for the Mid-Continent meeting. The Pacific Coast meeting will be held at Los Angeles. It is to be noted particularly that a Pacific Coast meeting was waived last year in favor of the annual meeting of the American Petroleum Institute, which was held at Los Angeles for the first time in nine years. It is hoped, and it was the understanding at the time among a number of individuals interested in both organizations, that in view of this action of the Petroleum Division the industry will give more than the usual support to the A.I.M.E. meeting this year. Ultimate Recovery is being considered as the keynote topic for the mid-year meetings. In view of trying financial conditions combined with an exceptionally high current potential rate of production, it is natural that the attention of the industry should be focused upon means of controlling production and reducing cost of operation. It seems that the Petroleum Division of the A.I.M.E., as a professional group, might

Jan 1, 1936

The officers and staff of the Petroleum Division are the servants of the members, and to the extent that the wishes of the members are made known and are practicable they will be carried out. The tentative plans outlined here are in general accord with previous custom, but modified by suggestions received recently from various members. The advice of all members is solicited, and it is hoped that the general expression on matters of policy can soon be facilitated by circulation of a questionnaire. Plans for two mid-year meetings of the Petroleum Division and for participation in the annual meeting at New York were inaugurated at the last annual meeting and are being carried forward as rapidly as possible in the belief that an early start will increase the possibility of finding the best available program material and permit the careful preparation, review, editing, and advance discussion of papers. While a number of papers have already been solicited, both members and nonmembers are hereby invited to submit additional papers, with the assurance that such papers will be given just as favorable consideration as the papers that have been requested. Mid-year meetings will be held at about the same time both in the Mid-Continent and California. The time will be selected if possible to coincide with the visits of President Lovejoy, who expects to be in California the last of September and in Texas early in October. Fort Worth, Dallas and Austin have been suggested for the Mid-Continent meeting. The Pacific Coast meeting will be held at Los Angeles. It is to be noted particularly that a Pacific Coast meeting was waived last year in favor of the annual meeting of the American Petroleum Institute, which was held at Los Angeles for the first time in nine years. It is hoped, and it was the understanding at the time among a number of individuals interested in both organizations, that in view of this action of the Petroleum Division the industry will give more than the usual support to the A.I.M.E. meeting this year. Ultimate Recovery is being considered as the keynote topic for the mid-year meetings. In view of trying financial conditions combined with an exceptionally high current potential rate of production, it is natural that the attention of the industry should be focused upon means of controlling production and reducing cost of operation. It seems that the Petroleum Division of the A.I.M.E., as a professional group, might

Jan 1, 1936

By David Keys

THE object of this investigation was to determine with a vertical magnetic variometer the extent of the titaniferous ore deposit that occurs not far from Ivry in Terrebonne County, Quebec, about 70 miles north of Montreal. The Ivry mine, on lots 37 and 38 of range V, Beres-ford township, Quebec, is one of the largest and most accessible to transportation of the deposits of ilmenite in Quebec. The ore consists of an aggregate of ilmenite anhedra serving as host for numerous fine plaques of hematite. No magnetite is known from any occurrence near this lot, and in this way the deposit differs from many others that contain a large percentage of magnetite with the ilmenite. The deposit at Ivry thus has much lower magnetic susceptibility than those containing abun-dant magnetite, and a sensitive magnetometer was necessary for the work, although a body of magnetite with ilmenite about a mile from the Ivry mine was successfully prospected with a dip needle. The principal orebody is exposed in a quarry known as the Ivry mine, from which about 16,000 tons of ore have been shipped. Small exposures of ilmenite isolated by drift serve to show the presence at the surface of some of the bodies indicated by the magnetometer,- but most of the hill is covered with glacial till and second growth hardwood. At the lower levels the till gives place to fluvioglacial sands and gravels from which the forest has been cleared. The increasing thickness of the sand and gravel as the hill descends makes the tracing outward of the deposits from the rocky knob of anorthosite a difficult matter. Within the orebodies too, some masses of anorthosite persist, which may account for some local irregularities. Fig. 1 is a photomicrograph, taken by reflected light, of a typical specimen of the ore. The dark patches are hematite and the light parts are ilmenite. No trace of magnetite was found. Fig. 2 is a photo-micrograph of a thin section of the country rock showing the texture of the anorthosite. The mean of four analyses quoted by Robinson1 is: titanium, 19.26 per cent; iron 45:41 per cent.

Jan 1, 1936

By Joseph Richards

PLATING iron with copper has received great attention from practical sand scientific men, but, aside from the deposit secured by immersion of iron in copper salts, by electro-plating, or by welding together thin sheets of iron and copper, these efforts have met with no success. Failure of these efforts, in the production of copper plating, has been due to the fact that the conditions normally and necessarily present in the plating operation are antagonistic to the production of copper-plated iron. In most, if not quite all of them, a bath of molten copper has been used. The-temperature of a molten copper bath is so high that the iron becomes oxidized before it can be immersed in the molten copper, and unless protective flux for the molten copper is used, the surface of the copper will become oxidized, and, in any event, the plated iron will oxidize immediately on its being withdrawn from the molten bath. I recently had the pleasure of visiting the works of The Metals Plating Co. at Elizabeth, N. J., where I witnessed the plating of iron sheets with copper by a new process.1 The plating metal is applied to the sheet in the form of a liquid mixture by means of rolls, such as inking rolls. The sheet, after being coated with the mixture, is automatically carried forward and deposited on a link-belt conveyor, which carries it through a furnace maintained at a. temperature well above that of molten copper. The basic principle involved in this method lies in the application of the plating metal to the sheet while the sheet is cold and then melting the metal in place on the sheet under conditions which are favorable to the formation of the plating.

Jan 1, 1919

By George Tryon, E. A. Barnard

The importance of the conservation of the waste heat contained in copper reverberatory furnace gases was realized very early by those in charge of operation at Anaconda. The first attempt to utilize it was in preheating the air used for combustion of the coal. This was done by forcing the air through ducts surrounding the flue-gas downtake and continued down beneath the furnace hearth to the firebox. Any small advantage gained by the heat transferred from the flue gases was more than offset by the losses sustained in cooling the hearth, therefore this process, after several trials, was soon discarded. It was first used at the Old Works as early as 1893 and again for a comparatively short time on the original furnaces at the Washoe smelter, or present works. Water-tube boilers came into general use very rapidly after 1890. Their adaptability for waste-heat steam generation, as well as the saving to be effected by the production of cheap steam from this source, was soon recognized. The first waste-heat boiler to be used in connection with a matte furnace at Anaconda was installed in September, 1900, at the "Old Lower Works." It consisted of a 100-hp. "Cook," vertical water-tube boiler. This boiler had 65 small perpendicular tubes arranged in concentric circles around a 10-in. tube in the center. These tubes were expanded into 4 ft. 4 in. inside diameter cylindrical steel top and bottom drums which served as the steam and mud drums respectively. This boiler was set in a cylindrical brick housing into which the furnace gases entered just above the mud drum and thence circulated upward around the tubes and steam drum to the stack. This installation proved unsatisfactory, presumably on account of difficulty with dust, and was soon abandoned. However, the possibilities for steam generation were undoubtedly encouraging for shortly afterwards (December, 1900) a 300-hp. Stirling boiler was installed, to be followed by two more in the spring of 1901. The choice of the Stirling type of boiler for application to copper reverberatory furnaces was particularly fortunate, as the arrangement of the tubes appears to combine to a great extent the maximum contact of the gases with the heating surfaces of the boiler and at the same time

Jan 1, 1934

By George W. Maynard

In the course of an examination of some of the California hydraulic mines in November last, I visited the property of the Gold Run Ditch and Mining Company, near Dutch Flat, Placer County. This is one of the most important and extensively worked mines in the district. The gold occurs in the characteristic blue gravel, which averages 175 feet in thickness, the lower 40-60 feet being made rip of cement gravel, which resists the action of water, and can only he loosened by blasting. The specimen which I have the pleasure of laying before the members was presented to me by Mr. I. L. Gould, the intelligent superintendent of the mines, who informs me that he found it in the old river channel, about twelve feet above the bedrock. The flattened water-worn nugget of gold, about the size of a kidney-bean, is imbedded in blue cement gravel, around which quartz has crystallized. When found the projecting portion of the nugget was enveloped in quartz, the core of gravel and gold having only been discovered after breaking the lump of quartz. On the quartz there is a shell of cement. The specimen is a remarkable confirmation of the theory of the deposition of quartz from solution. DISCUSSION. Dr. T. STERRY HUNT, in commenting upon this occurrence, remarked that it is in accordance with what we already know of the recency of some of the quartz of this region, and cited the microscopic

Jan 1, 1880

By A. J. Bowie

The discovery of the auriferous cement gravel deposits in and near Deadwood Gulch, Lawrence County, Dakota Territory, in 1876, created a mining excitement, and rush to the Black Hills. Numerous ten and twenty-stamp mills were built on Deadwood Gulch; Central City and the town of Deadwood sprang into existence, and became the centres of the mining industry of the Hills. Gold quartz deposits were subsequently discovered and located on a so-called mineral belt, extending from Whitewood Creek on the south, to Deadwood Gulch on the north. A northerly group of these quartz locations was purchased in December, 1877, by parties in San Francisco, who formed a company, incorporated under the name of the Father de Smet Consolidated Gold Mining Company. This company immediately commenced the work of exploration The deposits were proved to be extensive, and easily mined, but it was found that the ore, on an average, would not yield more than $10.00 per ton* of 2000 pounds. • At this trine the cost of supplies and materials in the Hills was high. Miners' wages were $3.50 per diem, and custom mills charged $6.00 per ton. The successful working of mines on "the belt" necessitated cheap milling. The ores being of so low grade,f this could be accomplished only with large and economically running mills. To insure the greatest possible economy, the Father de Smet mill

Jan 1, 1882

By E. L. Bruce

The district of Patricia, in the province of Ontario, lies northwest of the Albany River and extends northward to Hudson Bay. Formerly this was the unorganized district of Keewatin, the southern part of which was divided in 1912 between the provinces of Manitoba and Ontario. The interprovincial boundary now runs north from Lake of the Woods for 275 miles and thence northeast 375 miles to Hudson Bay. This district is comparable in size to all the older part of Ontario south of the Canadian Pacific Railway east of Lake Huron—thus it is roughly one-third of the whole of the present provincial area. The central part of this great triangle is one of the least accessible parts of Canada. From it streams flow southward to the English River, southeastward to the Albany, northward to Hudson Bay and the Hayes River, and westward to Lake Winnipeg. None of the streams is large and canoe travel is not easy. The only industry it has ever had is the trade in furs. Until the development of the airplane on a commercial basis, the only means of travel was by canoe or dog-train. There is not a mile of railway in the whole district. The two areas to be dealt with lie in the southwestern part of Patricia. Red Lake is 50 miles east of the Manitoba boundary and 75 miles north of the transcontinental railway from Cochrane to Winnipeg. Woman Lake is 50 miles farther east and slightly farther north. The late Dr. D. B. Dowling, of the Geological Survey of Canada, visited Red Lake and spent some time there during his exploration survey from Lac Seul to Berens River in 1893. He also visited the Woman Lake basin during the same journey, but his examination of it was much less detailed, the great area covered by him during the one field season making it impossible to make more than a hurried reconnaissance. Some prospecting in the Red Lake district followed Dowling's exploration, but the distance from railway was too great for any systematic work to be done. In 1922, following the usual plan, the Ontario Department of Mines made a geological reconnaissance of the English River, following :in instrumental survey of that river and its lakes by the Department of Lands. A side trip was taken to examine the rocks of Red Lake described

Jan 1, 1928

By Milton E. Wadsworth, R. Ted Wimber

Cobalt sulfate solutions containing ammonium acetate and chloroplatinic acid were reduced by hydrogen in a pyrex-glass lined autoclave in the temperature range of 170o to 232°C and hydrogen partial pressure range of 115 to 830 psia. The reduction rate was directly proportional to the hydrogen partial pressure and surface area of the pyrex glass and was independent of the quantity of chloroplatinic acid added initially. Experiments involving the variation of the relative concentration of ammonium acetate indicated that the reducible cobalt complex was probably the diacetate complex of cobalt, Co(AC)4H20, or a new mononcetate complex Co Ac, which was in solubility equilibrium with a pink precipitate of CO(AC)-4HzO. THE reaction in which a metal is dissolved by an acid to produce gaseous hydrogen and a salt solution was discovered early in the history of chemistry. In 1859 Beketoff found experimentally that this reaction could be reversed; i.e., a salt solution could be reduced by gaseous hydrogen to produce a metal and an acid. A review of work done on this phenomenon since that time may be found elsewhere., The hydrogen reduction of a cobalt salt solution is facilitated by complexing the cobalt ion. An ammonia complex of cobalt has been reduced commercially in the recovery of cobalt metal. A new reducible complex of cobalt was discovered5 when it was found that a co-baltous sulfate solution containing ammonium acetate could be reduced by hydrogen at temperatures in the region of 200°C. When a cobalt sulfate-ammonium acetate solution was heated to a temperature below its normal boiling point, a violet color became apparent, indicating complex formation. The nature of this complex was investigated5 by the addition of NH4Ac to a CoSO4 solution maintained at 85o. During the first additions of NH, Ac, the pH of the solution remained fairly constant at about 5.85. However, as the ratio of NH,Ac to CoSO, approached two, the pH rose and then leveled off at about 6.05. The absorption spectra of a Co(Ac), solution and a CoSO,, NH Ac solution were obtained at 85°C and were compared and found to be the same. These findings suggested that the diacetate complex of cobalt, Co(Ac),.4H20, was formed at 85°C. When a cobalt sulfate-ammonium acetate solution was heated to a temperature above about 165o, a finely divided pink precipitate appeared. The X-ray diffraction pattern of this precipitate indicated that it was Co(Ac), - 4H,O. In addition, it was discovered that when chloroplatinic acid, H,PtCl;, was added initially to the cobalt sulfate-ammonium acetate solution, a faster reduction was obtained. The roles of the solution complex, pink precipitate and chloroplatinic acid in the reduction process were then investigated. APPARATUS The experimental work was carried out in a two-liter stainless-steel autoclave. Adetailed description of the autoclave and the auxiliary equipment used in maintaining constant temperature and pressure may be found elsewhere.= Because the stainless steel was corroded, and also because it acted as a hydrogena-tion catalyst, an all-glass liner was fabricated such that the solution came only into contact with flame-polished pyrex glass. EXPERIMENTAL PROCEDURE The solutions used in the experimental work were prepared by dissolving reagent grade chemicals in distilled water. Although variation of the brand of ammonium acetate appeared to have no effect on the experimental results, CoSO, 7H O from the J. T. Baker Chemical Co. of Phillipsburg, N. J.,was found to give faster reductions than that prepared by Allied Chemical and Dye Corp., N. Y. The former was used throughout the course of the experimental work and was weighed up at the outset of each experiment. The ammonium acetate was dissolved to form a 6M stock solution, which was stored under refrigeration. A 10 pct solution of chloroplatinic acid (J. T. Baker Chemical Co.) was diluted to a 1.15 x 1Q2 M stock solution, which was standardized by precipitation of K,PtCl, as outlined by Scott. The appropriate volume of the chloroplatinic acid, H,PtCl,, solution was pipetted into the clean, dry glass liner. The cobalt sulfate-ammonium acetate solution, which had previously been saturated with

Jan 1, 1962

By R. F. Frantz, T. P. McNulty

The upper-level mineralization of the din Buttes, Arizona copper orebody consists primarily of dilute copper silicate impregnation in fault clay and throughout the altered limestone hostrock. Cuprite and native copper are minor with true chrysocolla rare. Owing to the high calcium carbonate and to the hydrogen ion exchange capacity of the clays, acid leaching would be economical only with cheap acid available. Leaching of the silicate copper with reagents other than sulfuric acid is slow and incomplete unless the ore is first heated to disorder the mineralized grains and to reduce partially the contained copper. Following heat treatment, 70 to 90 percent of the nonsulfide copper can be dissolved in aqueous anrmonium carbonate. Recovery of a pregnant solution by counter-current decantation is effective provided ammonium carbonate solution is added to the washing stages in order to oppose adsorption of dissolved copper by clays in the residue. Thermal stripping of the pregnant solution permits recovery of ammonia and carbon dioxide while precipitating copper either as oxide or carbonate. The research program was carried from batch tests through continuous miniplant operation to a five-month campaign in a 20 TPD continuous pilot plant. Pilot plant results, the relationships among key varibles, and a detailed flowsheet are given.

Jan 1, 1973

By A. Eilers

A MARKED peculiarity of most of the smelting-works of the Far West is the looseness with which accounts of the operations are kept. Indeed, probably over half of the works do not keep any detailed accounts at all, the yearly gross statement of profit or loss being considered sufficient for all purposes. The reasons for this must apparently be sought in the as yet unsettled state of all business relations, and in the deplorable fact that only in isolated cases educated metallurgists are in charge of the smelting-works. Continual and regular assays of the ores, by-products, and slags, are almost unknown, so that it is impracticable to ascertain, even approximately, the losses in the smelting processes. Of cases where regular accounts are kept of the quantities of ore smelted, of the composition of charges, and of the fuel consumed, I know only two or three. Under these circumstances it is extremely difficult to collect figures which cover the operations for a considerable length of time, and which are so valuable for the metallurgist, who wishes to get an insight into the economy of smelting operations, as shown by practice. Figures obtained by personal observation, which can of course cover only the brief space of the visit of the travelling metallurgist, must, therefore, be made to replace the more valuable data. The writer has had occasion, during the last and the preceding summer, to visit the larger number of the Western lead-smelting works, and offers, in the following pages, such data relating to the economy of lead-smelting in the blast furnace at various works, as he has been able to obtain. The only object in doing so is to place these figures on record, so that they may be from time to time supplemented with other data, which are now wanting. I. EUREKA CONSOLIDATED COMPANY'S SMELTING-WORKS. These works smelt the ores from the mines of the same company on Ruby Hill, Eureka, Nevada. The supply is almost unlimited,

THE Annual Fall Meeting held in Chicago in conjunction with the celebration of a Centennial of Engineering brought forth a round of field trips and symposiums which did much to add to the store of information of the 240 who registered for the gathering. Instead of a scattered program, technical papers were grouped together in organized symposiums, where the particular importance of each report was enhanced by presentation in context. Despite the heavy accent on technical papers and informative field trips, those attending the meeting had ample time to enjoy the benefits of a visit to Chicago. The AIME dinner dance was held at the Palmer House, in the Red Lacquer Room. The Chicago Section played host Friday evening at dinner. The MBD held four sessions at the meeting headquarters, the Palmer House, September 4 and 5. Featuring the meetings was a review of taconite concentration and new theories on comminution. The first session opened with a paper on the Structural Features Which Effect the Concentration of Iron Formations, presented by F. J. Tolonen. The paper was centered upon the various members of the low grade iron formations of the separate Michigan districts. The study correlated macrostructure, microstructure, and concentration tests. [ ] Beneficiation Characteristics of Michigan Low Grade Iron Ores, presented by F. X. Tartaron, cochairman of the session, reviewed the work of his laboratory on the beneficiation of low grade ore taken from various strata of a deep shaft on the Marquette Range. The paper included data on flotation, gravity separation, magnetic separation, and combinations of these processes. The economics of low grade ore treatment generated great interest. Ty. Maki offered a compilation and correlation of field results with magnetic separators in ferrosilicon and magnetite medium recovery circuits. Following the morning session, 130 persons attended a luncheon, followed by a brief business meeting. Later, a film illustrating the grinding, separation, and pelletizing steps investigated by the Mines Experiment Bureau, was presented by H. H. Wade. T. E. Ban, and L. J. Erck gave a report on pelletizing which evoked much discussion. R. A. Limons presented a paper on the Mineralogy of Blast Furnace Sinter, for its author, H. M. Kraner. Friday sessions featured a new hypothesis for high speed drill rod milling and a new technical approach to comminution. Jack Myers commented that Consolidated's large rod mill was a hammer mill turned inside out. Steve Erickson described the use of Cyclones for Heavy Media Concentration of Iron Ore Fines. Bob Meaders gave a Progress Report on the Aerofall Mill. Shiou-Chuan Sun described an improved high frequency analyzer for studying the conductivity of suspensions of various minerals. L. A. Roe discussed a magnetic reflux condensor which enabled him to determine the degree of liberation of magnetic iron ores. Roy A. Johnson described a function of the hydroscilator in which the fan rake was eliminated in favor of a conical bottom. The Industrial Minerals Division sessions held September 5 and 6 and were well attended. The Friday morning session was particularly concerned with developments and advances in industrial minerals with special emphasis on the Chicago area. The first two papers dealt with transportation on the Great Lakes and fuel movement into the Chicago area. The third paper proved to be of great interest, turning the spotlight on the fairly new hydraulic mining methods introduced by a silica company in the Ottawa, Ill. field.

Jan 1, 1952

By Alfred R. Powell

LATE in 1944 a group of petroleum and coal technologists was organized in Wash¬ington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Technical Oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. Since oil-production facilities in Ger¬many and the occupied countries con¬trolled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Industrial Intelligence Com¬mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined, mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A sum¬mary of the more important information gained by this combined British and American mission is presented below. GERMAN OIL PRODUCTION The oil available to Germany, both natural and synthetic, and including pro¬duction from occupied countries, reached a peak in late 1943 and early 1944. Pro¬duction at this time was at the rate of 1,200,000 metric tons per month, equiva¬lent to i00,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, 50 per cent was crude oil from Romania and Hungary, 12 per cent was crude oil from Germany itself, including Austria, 9 per cent com¬prised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of war¬time production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syn¬thetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per cent of the peak quantity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1946

By John V. Beall, William F. Haddon

A long the mighty Andean Cordillera, there is splendor beyond imagination-in the natural beauty of the mountains and in daring engineering and lavish investment in the mines. This is the story of the great copper mines of Chile and Peru. Each mine has a special quality which has tested the physical and spiritual resources of the founder. In the early days of the older mines, the mining engineer of song and story was more the rule than the exception. He was physically tough, ingenious and a leader of men. In the current political and social environment of Chile and Peru, the foreign contract mining engineer is still needed; but he must be a different type of man. To John J. Selters at Cerro's Rio Blanco, the principal ingredient is still "toughness," but it is "toughness of mind" that is needed. "He probably should be a teacher." The copper mines are not new. They were, almost without exception, worked by Indians (La Exotica might prove the rule), and later by the intrepid Spaniards. Modern mining began after the turn of the century. In Chile, the first of the big ones was the Braden Copper Co. founded on the El Teniente deposit. This development was followed by Chile Exploration Co. at Chuquicamata and Andes Copper at Potrerillos. These properties have been developed over the years by vast expenditures of money and a monumental amount of labor. None was free of technical problems-metallurgy at Chuqui, marginal grade of the old mine at Andes, avalanches and the great fire at El Teniente. The evolution which has brought the established mines of Chile, and the new ones coming on stream, to their present state of development is in reality the work of wonders of input-money, engineering and responsible management in an atmosphere of political stability. Without any one of these, the result would have been failure.

Jan 11, 1969

ONE of the interesting-though not unnatural-features of the whole Porphyry Copper development is the way in which the history of each property dovetails with that of one or more of the others. The same names keep cropping up as one digs into the accounts of events from 1900 to 1915. J. Parke Channing made examinations of Nevada, Ray, and Inspiration, as well as of Miami. Henry Krumb did important work in the early stages of the exploitation of Utah, Nevada, Ray, Braden, and Inspiration. Pope Yeatman was favorably impressed with the Braden property before he had ever visited it, when he saw a batch of Braden ore sent to the United States for testing. It reminded him immediately of Nevada Consolidated ore: indeed, he was unwilling at first to believe that it came from South America. And it was while working on the examination at Utah Copper that Philip Wiseman became enthused with the possibilities of the Ray mines. In 1905, Mr. Krumb, under the general direction of A. Chester Beatty, was strenuously engaged at Bingham, Utah, in arriving at an answer to this question: Should or should not the Guggenheim interests back Jackling to the tune of several million dollars to build the big concentrators at Gafield? Seeley W. Mudd was the Guggenheim engineer on the Pacific coast and in that capacity was indirectly responsible for the work at Bingham. At his suggestion Wiseman came up from Los Angeles as one of Krumb's assistants-at $5 per day, incidentally. A little later Mr. Mudd, in Utah on one of his visits, went down to Bingham. That evening in the old Hills Hotel in Markham Gulch he was going over reports with Mr. Krumb. Wiseman and some of the other engineers on Krumb's staff were present. During a breathing spell, Mudd expressed

Jan 1, 1933

By Eugene McAuliffe

IT is not possible to include in this paper, limited as it is in scope, the many diverse steps toward the reduction of mine accidents that are taken in the mines that produce the nation's coal. Every coal-producing state has enacted laws covering proper mining practices, and the major portion of these are directly related to the safety of the mine employees. The United States Bureau of Mines, the American Institute of Mining and Metallurgical Engineers, The American Mining Congress, a number of national, regional and state organizations, as well as the coal technical press, have covered time and time again all of the "do" and "don't" phases of mine operation that bear on the important question of mine and employee safety. Within the past 15 years The Union Pacific Coal Co. has attempted to put into practice in its mines in southern Wyoming these many good recommendations, finding some value in all, and yet, to secure substantial results, the management found it necessary to resort in the end to what might be referred to as "extra-territorial" methods. It is the writer's purpose to show in this paper that marked and even extraordinary betterment can be brought about when employer and employee work together with due sincerity. In presenting our own experience, one that has been duplicated in so far as results are concerned on numerous other properties, no theory of perfection of management exists; on the other hand, our organization feels that as long as our record of accidents remains as shown by even our latest and best performance we still have far to go. It is the writer's purpose to show in this paper that marked and even extraordinary betterment can be brought about when employer and employee work together with due sincerity. In presenting our own experience, one that has been duplicated in so far as results are concerned on numerous other properties, no theory of perfection of management exists; on the other hand, our organization feels that as long as our record of accidents remains as shown by even our latest and best performance we still have far to go.

Jan 1, 1938

By H. S. Geismer

INTRODUCTION. THERE are three general methods available for obtaining commercial brown iron-ore : hand-screening; washing; and washing and concentrating. Hand-screening has produced a large tonnage of ore in the past, but is rapidly falling into disuse, except as a preliminary step, largely because modern furnace-practice requires all foreign material to be separated from ores before they are delivered to the furnace, and hand-screened ores can rarely be made to fulfill that requirement. Another argument against hand-screening is, that the waste-pile often contains as much ore as the screen recovers. The operation known as hand-screening consists of throwing the ore-bearing material against a stationary inclined screen of 0.5- to 0.75-in. mesh, similar in construction to the screens employed in sand-pits. The recently-prospected brown-ore deposits of Cuba seem to offer possibilities for hand-screening not possessed by the average American deposit, since these ores are not associated with worthless clays. Washing, and washing and concentrating, may be discussed together, since concentrating is never practical on brown iron-ore, except to treat ores that have already been washed. (Strictly speaking, washing might be classed as concentrating, but it is never so designated by brown-ore men.) The various steps of removing ore-bearing material and converting it into ore suitable for blast-furnace use, may be grouped under five heads: loading for transportation ; transporting ; feeding into the washer; washing; and concentrating. These five subjects will be considered in consecutive order. Each of these successive steps may be accomplished in a number of different ways, the choice depending entirely upon the character of the ore-bearing material to be treated.

Aug 1, 1911

By H. Merton Ruth

THE northern anthracite fields, although facing the same economic problems as the southern fields, are confronted with the additional problem of fast dwindling reserves of anthracite which can be conventionally and economically won. The mining of coal which remains in thin beds and the recovery of pillars from areas heretofore considered unrecoverable, either by reason of cost or surface restriction, pose problems of in- creasing importance to the economic life of the northern field operations. Successful approaches have Been made to this problem and other work is being performed that holds promise. There exists in the northern anthracite field millions of tons of solid coal, the recovery of which has not been too successful due to the following inherent operating faults: inability to concentrate producing areas; the great quantities of rock to be cut and handled, lack of consideration of proper sequence and speed of second mining, and the continued use of the mine car as the basis of payment. A mining system that has successfully solved these major problems has been in operation in the Scranton area since 1944. Over 1% million tons have been produced from veins varying from 3 to 4% ft thick by this method, which is known as the multiple panel-triangular system-conveyor mining.

Jan 1, 1950

By Theodore Swann

DURING recent years, there has been a material increase in the use of ferrophosphorus in the steel industry. It has been observed, when rolling sheets, that those made of Southern iron did not have to be rolled at as high a temperature as the others and, consequently, did not stick together. The reason was found to be the phosphorus content of Southern iron. It was therefore thought that an addition of phosphorus to sheet steel of other than Southern origin would give the same result as the use of Southern iron. At first, this addition was made by intro¬ducing phosphate rock in the blast furnace and reducing it together with the iron ore; but, because of the necessity for only small quantities of this grade of iron, the process was not satisfactory. The manufacture of ferrophosphorus was then introduced, so that additions might be made to the open-hearth furnace or ladle. Ferrophosphorus was first manufactured in the blast furnace. This method, however, can only economically produce a grade of product up to about 20 per cent. To produce a higher grade, it would be necessary to charge a larger proportion of phosphate-bearing material; and as the rate of absorption by the iron is low, there would be an increased loss of phosphorus oxides. This feature makes the production of a higher grade ferrophosphorus in the blast furnace uneconomical. The use of high-grade ferrophosphorus in the steel requires a smaller addition and involves, besides the economies in handling, an additional economy in transportation. The alloy with a higher percentage than 20 per cent. can be made only in the electric furnace. In the ordinary operation of the electric furnace in the production of ferrophosphorus, an alloy may be produced containing 26 per cent. phosphorus; this is the limit, for it does not seem possible to produce a higher phosphorus alloy even if large excesses of phosphatic materials are used. The reasons for the difficulty in raising this percentage of phosphorus are not known. The compounds Fe3P, containing 15.6 per cent., and Fe2P, containing 21.7 per cent. phosphorus, have been studied and it appears as if the alloy produced, containing percentages of

Jan 10, 1924