Search Documents

Edwin H. MessiteR, New Pork City (communication to the Secretary*):—Under the heading " Flues," Mr. Edwards refers to the Bee-hive construction, a cross-section of which is shown in Fig. 4 of his paper. A flue similar to this was designed by me about six years ago,' in which the walls though much thinner than those described by Mr. Edwards gave entire satisfaction. These walls, from 2.25 in. thick throughout in the smaller flues, to 3.25 in. in the larger, were built by plastering the cement mortar on expanded-metal lath without the use of any forms, or cribs, whatever, at a cost of labor generally less then $1 per sq. yd. of wall. Of course, where plasterers cannot be obtained on reasonable terms, the cement can be molded between wooden forms, though it is difficult to see how it can be done with an interior core only as stated by Mr. Edwards. In regard to the effect of sulphur dioxide and furnace-gases on the cement, I have found that, in certain cases, this is a matter which must be given very careful attention. Where there is sufficient heat to prevent the existence of condensed moisture inside of the flue, there is apparently no action whatever on the cement, but if the concrete is wet, it is rapidly affected by these gases. At points near the furnaces there is generally sufficient heat not only to prevent internal condensation of the aqueous vapor always present in the gases, but also to evaporate water from rain or snow falling on the outside of the flue. Further along, a point is reached where rain-water will percolate through minute cracks caused by expansion and contraction, and reach the interior, even though internal condensation does not occur there in dry weather. From this point to the end of the flue the roof must be coated on the outside with asphalt paint or other impervious material. In very long flues a point may be reached where moisture will condense on the inside of the malls in cold weather. From this point to

Jan 1, 1905

By W. V. Vietti, E. P. Hayes

OpeRations on the Texas Gulf Coast during 1936 increased materially over 1935. A number of new fields were discovered and a few of the older fields were extended, both by the discovery of deeper pay sands and by lateral expansion of the known producing horizons. Twenty-seven new fields have been discovered, of which 25 are oil fields and the others are gas fields that have every indication of becoming oil-producing areas. Amelia, Anahuac, Bay City, North Pettus, Placedo, Pickett Ridge and Tomoconnor have had major extensions. Production for 1936 amounted to 91,224,844 bbl., an increase of 21,627,033 bbl., or 31 per cent, over the 1935 production of 69,597,811 bbl. The number of producing wells at the end of 1936 was 6727, as compared with 4851 at the end of 1935. Proration has continued in force, thus decreasing the rate of depletion and the number of abandonments normally expected. New Fields A brief discussion of the new fields follows, in addition to Tables 1 and 2, which contain the general data on these fields. Aransas (McCampbell).-Buckingham and McCampbell No. 1 McCampbell was drilled to 7501 ft., then plugged back to 6560 ft. and completed in the Marginulina for a 100-bbl. flowing well on July 18. Bee County.—The Voss field, discovered by Swiger and Devonian's No. 1 Voss, and the Holzmark field, discovered by Miller and Donzis on the Holzmark farm, are both of the same type structurally and are caused by folding against a fault, one field being on one side of a fault and the other on the opposite side of the same fault. Brooks County.—-Standard Oil Company of Texas Garcia No. 1, the discovery well in the Alta Mew field, and Dick Young's Singer No. 1, the discovery well of Alta Verde, appear to indicate small fields. Garcia No. 1 was drilled to 8022 ft. and plugged back to 2485 ft., at which depth the well made 189 barrels. Lockridge.—This gas field was discovered by Gulf Production Company's Fairfield No. 1, in Brazoria County. It was originally drilled to

Jan 1, 1937

H. W. NICHOLS, Secretary-Treasurer, Field Museum of Natural History, Chicago, Ill. , R. S. BONSIB, H. B. PULSIFER, . HORACE H. CLARK, H. T. WALSH. Seventy-four members of' the two organizations attended a three-day joint field meeting of the Chicago Section and the Illinois Mining Institute at La Salle, Ill., on May 17, 18 and 19. The meeting began with a technical session in the rooms of the Illinois

Jan 7, 1917

By H. O. Hoffman, C. D. Demond

There are two methods of determining the fusibility or refractoriness of fire-clays, the theoretical and the experimental. In the former, conclusions are drawn from the chemical composition; in the latter, from the changes which the clay undergoes when subjeoted to intense heat. It is well to use both methods, beginning with the actual heat-test and explaining the results obtained from this by the help of the chemical analysis. In discussing the subject, however, it is better to reverse this order. I. The Theoretical Method.* Leaving out the hygroscopic and combined waters and any organic matter, as not directly affecting the fire-resisting property, the refractory constituents of fire-clay are alumina and silica, and the fluxing constituents magnesia, lime, soda, potash and ferric oxide. According to Bischof,† alumina is the least fusible component, and silica follows close upon it. If, however, a mixture of the two be heated, it will be found that its melting-point is much lower than that of alumina, as a silicate will then have been formed. The way in which silica affects the refractoriness of alumina has been strikingly presented by Seger 1 in a diagram reproduced in Fig. 1. The abscissæ represent the melting-points of Seger cones Nos. 26 to 36 (see p. 55); the ordinates, the relative amounts of alumina and

Jan 1, 1895

SOUTHERN CALIFORNIA SECTION Executive Committee SEELEY W. MUDD, Chairman. C. COLCOCK JONES, Vice-Chairman. FREDERICK J. H. MERRILL, Secretary-Treasurer, 631 Higgins. Bldg., Los Angeles, Cal. RALPH ARNOLD A. B. CARPENTER A. B. W. HODGES WILLIAM F. STAUNTON The third meeting of this winter season tool: place in a private dining room of the Sierra Madre Club in Los Angeles on Feb. 1, 1916, at 6:30 p.m., 22 members and guests being present. In the absence of the Chairman, S. W. Mudd, the Vice-Chairman, C. Colcock Jones, presided. After an enjoyable dinner the meeting was called to order, and the first paper by Ralph Arnold on Conservation of Oil and Gas in the Americas was read by the Secretary. W. F. Staunton then read an important paper on The Influence of California Oil on the Mining Industry of the West. In this he touched upon the uses of oil as a fuel for generating power, especially in connection with the Diesel engine. This paper was discussed it some length by J. F. Mitchell-Roberts, R. B. Moran, F. H. Asbury and L. D. Godshall. The Chair then introduced Robert B. Moran of the California State Mining Bureau, Deputy Supervisor of Gas and Oil, for the' Los Angeles . District, who addressed the meeting on the work of his department. The meeting concluded with A. B. Carpenter's reading of a paper on The California Gasoline Industry by W. R.. Hamilton, Manager of the Ventura Refining Co. F. J. H. MERRILL, Secretary. ,

Jan 4, 1916

SOUTHERN CALIFORNIA LOCAL SECTION Executive Committee THEODORE B. COMSTOCK, Chairman SEELEY W. MUDD, Vice-Chairman FREDERICK J. H. MERRILL, Secretary-Treasurer, 631 Higgins Bldg., Los Angeles, Cal. A. B. CARPENTER C. COLCOCK JONES A meeting of the Southern California Local Section, in honor of the presence of Secretary Bradley Stoughton, was held at luncheon in a private dining room of the Sierra Madre Club on Friday, May 21, 1915, 27 members and guests being present. In the absence, through illness, of the Chairman, Dr. Comstock, the vice-Chairman, Seeley W. Mudd, presided. After the luncheon, Secretary Stoughton made a short address on the activities of the Institute. George S. Rice, of the U. S. Bureau of Mines, who was present, then spoke on the activities of his Bureau. Local Secretary F. J. H. Merrill gave a description of the activities of the Southern California Section and its progress, and reported the latter as substantial and its condition as very good. After some informal remarks by other members present the meeting adjourned. F. J. H. MERRILL, Secretary.

Jan 7, 1915

By Geoffrey Gilbert

A study of specimens shows that the key to both oxidation and enrichment at Duck-town is the behavior of pyrrhotite, which is in part dissolved and in part replaced by marcasite. Enrichment takes place chiefly at the expense of marcasite. THE material that forms the basis of this paper was collected in the spring of 1922, during a ten-day visit to Ducktown by the writer in the company of Prof. L. C. Graton. The time available for the work was far too short to allow anything like a thorough study of the deposits, and structural and stratigraphic questions, though they have an important bearing on the origin of the primary ores, were necessarily left untouched. Attention was focussed on the zone of oxidation and enrichment; and by devoting most of our time to the upper levels, open pits, and old workings, and examining the deeper levels only thoroughly enough to obtain a fair idea of the nature of the primary sulfide ore, we were able to make a reasonably complete survey of the various orebodies. With this field work for a background, the writer later made a study, in the Harvard laboratories, of the specimens obtained during the visit. As some of the facts brought to light by this study appear to be new, it seems worth while to set forth the outstanding features and a proposed explanation of them. Much of the Ducktown material that is obviously of greatest significance, as regards oxidation and enrichment, is soft and crumbly. Notwithstanding the desirability of gaining from such material all possible information as to its mineral composition and textural relationships, but little has heretofore been learned regarding it; but, by suitable preparation of this material in connection with the present study, it has been possible to examine it under the microscope without any disturbance of its texture and about as satisfactorily as if it were hard, fresh ore. The information thus gained has contributed measurably to the results set forth in this paper.

Jan 3, 1924

The Ural Mountains, which were formerly the dividing line between Asia and Siberia, area chain of low mountains, the highest peaks reaching only a little over 5000 ft. The country has been much eroded and the mountains now appear as rounded hills. In the central and northern parts turf swamps abound. The range is covered with forests except at the extreme southern end. The trees are mostly pine. Birch grows on cut-over areas, but never to large size. The rivers are small or the fall is slight, so no large water powers are available. A series of rivers with a north and south course, and which are navigable for long distances, furnish cheap transportation during the summer months. Railroad communications are very insufficient. The first active exploitation of the mineral wealth was initiated by Peter the Great, who sought iron and copper for use in his wars against the Swedes. He selected a blacksmith named Demidoff to supervise operations and gave him rights to most of the Ural and to the Altai. The Nijni Tagil Estates are still in the possession of the Demidoff family. The original large grant was subsequently subdivided through inheritance and marriage, but the Ural is still a country of very large estates, some of them held as leases only and some of them by actual ownership.

Jan 6, 1919

By Vince Poxleitner, John Delaney

Introduction In the mining industry, comminution typically begins in the mine with a blast of explosive to break rock so that it can be handled by the avail- able equipment. Though the breaking of the rock is essential for material handling in the mine and plant, this is not the only reason for ore reduction in the mineral industry. Comminution is primarily required to liberate minerals from ore so that they can be concentrated into valuable products or to prepare minerals, such as talc, for market as mined. The size of the equipment used for comminution ranges from small to massive. Regardless of equipment size, the power required to reduce the rock is a major expense. Years ago, mineral deposits could be mined more selectively and required less grinding to produce saleable products. However, as richer deposits were depleted, it has become necessary to mine low-grade deposits, with the valuables dispersed throughout the rock. Comminution equipment evolved in physical size and capacities to meet the new mine and process requirements. A modern, modestly sized mining operation, with a capacity of 25.000 TPD may use crushers two stories high weighing over a million pounds, SAG mills 36 feet in diameter driven by dual motors putting out 10.000 horse- power, and ball mills over 16 feet in diameter . Because of the increasing size and weight of modern equipment, the builder is faced with the problems of erecting massive foundations and field assembling equipment on these foundations. As equipment costs and plant construction costs increase, builders are finding that owners are asking for more detailed progress and cost data. Comminution construction projects are generally classified as grass roots plants or expansions or modifications to existing plants. It is estimated that 60-702 of the jobs involve existing plants. Today ' s costs for construction of small, new comminution plants can reach tens of millions of dollars; larger plants can cost hundreds of millions of dollars. Modifications, on the other hand, usually run from a few thousand to several million dollars. Though many problems are common to the construction of both new plants

Jan 1, 1982

By Laurence Delisle, Arron Finger

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Arron Finger, Laurence Delisle

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

PENNSYLVANIA ANTHRACITE SECTION Executive Committee R. V. NORRIS, Chairman. CHARLES F. HUBER, Vice-Chairman, W. J. RICHARDS, Vice-Chairman, EDWIN LUDLOW, Vice-Chairman, ARTHUR H. STORRS, Vice-Chairman. CHARLES ENZIAN, Secretary-Treasurer, U. S. Bureau of Mines, Wilkes-Barre, Pa. DOUGLAS BUNTING, FRANK A. HILL, ALBERT B. JESSUP, RUFUS J. FOSTER, JOHN M. HUMPHREY, ROBERT A. QUIN. The Pennsylvania Anthracite Section held its second regular meeting at the Pottsville Club House, Pottsville, Pa., July 25,1914. The meeting was attended by more than 90 members and guests. Vice-Chairman W. J. Richards presided. Following an informal dinner, W. G. Whildin, Mining Superintendent, Lehigh Coal & Navigation Co., Lansford, Pa., presented a. paper on Steep Pitch Mining of Thick Coal Seams, illustrated by numerous drawings. This paper will be printed in the November number of the Bulletin. A lively discussion followed the reading of the paper.

Jan 10, 1914

By JOHN R. SUMAN

IT appears now that the conflict with the totalitarian states will be a long-drawn-out struggle. The course of this war up to now indicates that this may well be the first major conflict where man power has not been the vital and determining factor. Mechanized warfare has made it possible for relatively small, well-equipped groups to outmaneuver and defeat large armies which lack the necessary modern equipment. Under these circumstances, ultimate victory becomes a matter of resources and productive ability. The important question is not how many soldiers can he put into the field, but the volume and speed in producing the armaments essential to ensure a victory. The resources available to the opposing nations and the efficiency of their systems of enterprise and production will be primary factors in determining the ultimate outcome. Germany had a head start of eight years in the armament race, and it is not easy to overcome such an advantage overnight.

Jan 1, 1942

By K. P. Gupta, A. K. Pal, L. Chandrasekaran, U. P. Singh

The Mn-Sn binary system, investigated at the high-manganese end and between 500° and 1000° C, shows four phases at temperatures below 727"C, namely the u Mn, the p Mn, the Mn3 Sn, and the Mn, Sn phases, while at higher temperatures only the last three phases remain stable. The solubility of tin in a Mn is very small and the maximum solubility of tin in P Mn phase appears to be abollt 10 at. pct Sn. The solubility range of the Mn,Sn and the Mn, Sn phases is 23.0 to 26.0 and 37.0 to 40.0 at. pct Sn, respectively. The lattice parameter of the 13 Mn phase increases with increasing tin content. The Mn, Sn thase is hexagonal with and appears to be basically of the Ni3 Sn type structure except that for quite a few X-ray diffraction lines the calculated and observed relative intensities do not agree well. The Mn-Sn binary system has been studied by several investigators.''~ Their results indicate that three intermediate phases, namely, the Mn3Sn, Mn,Sn, and MnSn, phases, exist at high concentrations of tin. However, so far the proper phase equilibrium has not been established at the manganese-rich end and very little data is available for the composition range between pure manganese and Mn3Sn. Moreover, earlier investigators differ in their opinion about the exact composition range at which the Mn3Sn and Mn,Sn phases appear and some doubt has been cast by some investigators3 regarding the structure of Mn3Sn phase which has been reported to be isotypic with Ni3Sn (Mgscd type) structure. In this investigation an attempt has been made to establish the proper phase equilibrium between pure manganese and Mn + 50 at. pct Sn composition in the temperature range of 500" to 1000°C. PROCEDURE The raw materials used were from three different sources. For exploratory work five alloys containing 5, 10, 15, 20, and 25 at. pct Sn were prepared using 99.9 pct pure manganese and tin supplied by E. Merck & Co., Germany. The rest of the alloys and one more 25 at. pct Sn alloy were prepared using 99.9 pct Mn supplied by Gallard Schlesinger Chemical Mfg. Corp., U.S.A., and 99.999 pct Sn supplied by Semi Elements Inc., U.S.A. Weighed amounts of manganese and tin were melted in recrystallized alumina crucibles in an inert gas (argon) high-frequency induction melting furnace. By careful control of temperature and time of melting the losses were reduced to below 0.2 pct in all cases. Since the losses were very small, no attempt was made here to analyze the samples chemically. Alloys were wrapped in molybdenum foil and sealed in small evacuated fused silica capsules. The alloys were annealed at different temperatures, controlled within + l°C, for sufficiently long periods to attain proper phase equilibrium, and subsequently quenched in cold tap water. The annealing periods used at different temperatures were 15 days at 500°C, 7 days at 600°C, 5 days at 700" and 750°C, 3 days at 800°, 850°, and 900°C, 2 days at 968"C, and two alloys annealed at 968°C were reannealed for 10 hr at 1000° C. From each annealed specimen, a part was utilized for metallographic study while another piece was used for X-ray diffraction study. 1.0 pct HNO, solution and oxalic acid solutions of concentrations 0.05 to 1.0 pct were used for etching Mn-Sn alloys above and below the MnsSn composition, respectively. Since all alloys were brittle, X-ray specimens were prepared using the as-crushed -325 mesh alloy powders. Only one 25 at. pct Sn alloy powder was reannealed in an evacuated silica capsule at 800°C for 5 min and water-quenched. X-ray diffraction patterns . for the Mn3Sn phase with the as-crushed and the reannealed powders did not show appreciable change. Un-filtered iron radiation at 25 kv, 15 ma was used with either Norelco 114.6-mm-diam Debye Scherrer Camera (for phase identification) or Norelco 12-cm-diam symmetrical focusing camera (for lattice parameter determination of the 6 Mn phase). The estimated accuracy of lattice parameter determination for the focusing camera was * 0.001A. RESULTS AND DISCUSSIONS The results of metallographic and X-ray diffraction study made with different alloys are shown in Fig. 1. The variations in lattice parameter with composition for the p Mn and the Mn3Sn phases are given in Tables I and 11, respectively, and the lattice parameter as a function of composition for the p Mn phase is shown in Fig. 2. The lattice parameter of the p Mn phase increases with increasing tin content while for the Mn,Sn phase the data obtained from two two-phase alloys and one single-phase alloy indicate increase in a,, and decrease in c, parameters with increasing tin content. The results, Fig. 1, indicate that the solubility of

Jan 1, 1969

By Charles C. Goddard

Since discovery of silver-gold lode deposits in 1864, the Butte district has produced more than $2.25 billion worth of copper, zinc, manganese, silver, and gold, an unprecedented value in the mining world. Exhaustion of the gold placer deposits along Silver Bow Creek, southwest of Butte, forced the early-day placer miners to turn their attention to the bold out- crops of the many veins exposed on the hillsides above the placer diggings. These outcrops bore silver and gold, and enough so that many lode claims were located. Such famous silver mines as the Alice, Moulton, Magna Carta, Nettie, and Blue Bird were developed. These and many smaller operations contributed to making Montana the leading silver-producing state in the 1880's. As depth was gained in the silver mines in certain parts of the district, occurrence of zinc minerals became troublesome. Zinc was not recoverable at the time, and in the chloridizing, roasting, and amalgamation of the ores, silver and gold recovery was greatly reduced. A period of active silver mining continued until 1892, when a decline in the price of silver brought the silver mining period to a close. Elsewhere in the district it was discovered that while some of the veins contained silver ores in the oxidized portions, the predominant minerals that were deeper were copper-bearing. Marcus Daly exposed rich copper ore on the 300 level of the Anaconda mine in 1891, and mining in the district disclosed that copper was destined to be developed in abundance. Early copper ore shipments were made to Swansea, Wales.

Jan 3, 1959

By S. S. Arentz

An organized safety program has reduced accidents at Pioche because effort is first devoted to arousing and maintaining interest in safety, followed by training in accident prevention, assigning responsibility for the detection and removal of safety hazards, and finally, by keeping score through an adequate system of records. A health program is intergrated with the safety program.

Jan 1, 1950

BOSTON LOCAL SECTION Executive Committee HENRY L. SMYTH, Chairman ALFRED C. LANE, Vice-Chairman AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS ALBERT SAUVEUR Meets on the first Monday evening of each winter month Twenty-fourth Meeting The Twenty-fourth meeting of the Boston Local Section was held at the Exeter Street Theater, Boston, Monday, Jan. 4, 1915. The Chairman, Henry L. Smyth, introduced Mr. S. Le Fevre, of Mineville, N. Y., who presented an exhibit of moving pictures, illustrating the various operations of mining and milling iron ore as carried out at Mineville. Mr. Le Fevre pointed out, as the pictures were run off, the dangers of the various operations, and the precautions that should be taken to avoid or minimize these dangers. . After the exhibition of pictures, the members adjourned to the University Club, where dinner was served. At the close of the dinner and an impromptu recital by Mr. Weeks, the meeting was adjourned. AUGUSTUS H. EUSTIS, Secretary.

Jan 2, 1915

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with low ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the size range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for vari¬ous reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully.

Jan 1, 1953

By Willard P. Ward

Having been engaged during the past year in the manufacture of ferro-manganese in a blast furnace, I have imagined that some further information on this subject might be of interest to that large number of members of the Institute who are engaged in the iron and steel industries. The great question of the economical production of good steel, ingot metal, or homogeneous iron (we scarcely know now what to call it) from good materials, and at reasonable prices, has, thanks to the intelligence and energy of a few American engineers, been successfully solved in this country. Nearly all first-class railroads, and many that would not rank so high, have adopted the Bessemer rail. Martin boiler-plates are rapidly gaining ground, in competition with

By R. C. Mahon

Operators concerned with the destruction of their piping by acid mine waters will be interested in the method by which this problem was solved at the Cardiff mine of the Homer group. Rubber lined, or acid resisting metal pipes were found too expensive. Casting concrete lining in pipe would have required a minimum thickness of one inch, thus excessively reducing the pipe's diameter, as well as taking twenty four hours per length of pipe. The Naylor Pipe Co. of Chicago, having experimented with centrifugal lining of pipe with concrete, provided information which eventually solved the problem. An experimental plant was constructed as shown, and the following procedure developed : (1) Kerosene is used to remove the interior oil coating of new pipe. Closed with blank flanges, the pipe is revolved for eight minutes at varying speeds. Stopping and starting the motor achieves a good washing action. The kerosene is then drained off, and similar washing action with caustic soda removes any excess. Swabbing in done with burlap fastened to a 1/2-in. pipe. (2) The aggregate, made of one. part quick-setting cement and two

Jan 1, 1949