Search Documents

By David B. Reger

Extensive drilling for gas and increased pipe-line building were the major petroleum activities in West Virginia during 1937. According to the West Virginia Department of Mines, 1034 permits to drill were issued. A running account of operations from trade journals and other reports shows that 1041 wells were drilled, resulting in 193 oil wells with 1238 bbl. of daily production; 680 gas wells with 1,048,057,000 cu. ft. of daily open flow; and 168 dry holes. The new oil-well average is 6.4 bbl. per well per day; the gas-well average is 1,541,260 cu. ft. per well per day; the ratio of dry holes to completions is 16.13 per cent. Very little attempt was made to develop new supplies of oil. Because of the continued low price, operators evidently considered it good business to leave oil in the ground rather than to produce it at a loss or on a small profit basis. The principal oil wells completed, by counties, are: Calhoun, 16; Clay, 10; Pleasants, 17; Ritchie, 42; Roane, 16; Tyler, 13; Wetzel, 11; Wirt, 14; Wood, 13. The leading counties in gas, with the number of successful wells in each, are: Boone, 54; Braxton, 31; Cabell, 48; Calhoun, 46; Gilmer, 82; Kanawha, 134; Lincoln, 44; Ritchie, 56; and Wayne, 26. General State of the Industry In Table 1 will be found an approximate summary of oil and gas territory and reserves, oil and gas production and number of oil and gas wells. The amount of land under lease is an approximation, because the exact figures are not available through any public or private agency. The proved land and reserves represent the opinion of the writer. The oil production for 1937 is subject to revision, and the gas production for the same year is only an estimate, based on demand and supply. The number of oil and gas wells now active is also an approximation, based on previous studies, and revised for completions and abandonments. Principal, Areas of Activity In Boone County, 62 wells were drilled in various localities, resulting in 4 oil wells and 54 gas wells with 18,170,000 cu. ft. of new production.

Jan 1, 1938

By Stanley F. French, Bruno F. Koch

Although the amount of dust that will be actually recovered in the six main dust-control systems cannot be accurately stated until the tests mentioned previously are carried out, it is estimated that the average air entering the wet collectors will contain around 5 grains of dust particles per cubic foot. This means that the six systems handling a total of about 133,000 cu.ft. of air per minute will return about 68 1/2 tons of dust to the concentrator per day and since the copper in this dust will average around 2 per cent, the total recovery is approximately 1.37 tons of copper every 24 hours. This important copper recovery is not due entirely to the dust-control system since in a plant without control only the duct that is dispersed to the atmosphere represents a loss. A conservative estimate of the recovery of copper solely due to the dust control system would be about half of the total or approximately 0.70 tons of copper per day.

Jan 1, 1942

By John Chipman, Theodore B. Winkler

IN order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chipman,3 dealt with the simplest possible slag system that would resemble those found in the basic open hearth-the slag system consisting of CaO-MgO-SiO2-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemistry of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, Si02, FeO, Fe203, P205, MnO, A1203 and CaF2, but not all of the slag samples contained all of these components at one time. REVIEW OF LITERATURE Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Brings4' von Samson-Himmelstjerna,5 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution ratios

Jan 1, 1946

By Reuel A. Cochrane, Harry H. Angst

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By R. D. Begley, A. W. Khair

Introduction The technique being investigated here uses a physical mine model which consists of a plexiglass room-and-pillar model 11.4 x 11.4 cm (4.5 x 4.5 in.). It is placed at the bottom of a larger plexiglass box 25.4 x 30.5cm (10 x 12 in.). The box is then filled with a model material representing geologic overburden. Sand has been selected because of its deformability under gravitational forces. The mine model is capable of creating a cavity and induces movement on the surface of the model material. This surface disturbance can be measured using a photographic technique called holographic interferometry. This paper discusses results of an investigation of the possibility of generating subsidence criteria using physical mine models and laser holographic interferometry. Problem Statement Subsidence appears to be widespread in two states - Pennsylvania and Illinois - although serious subsidence is found in localized areas of numerous other states (HRB Singer Inc., 1977). The US Bureau of Mines estimates that more than 1618 km2 (400,000 acres) of urban areas are threatened by subsidence. Pennsylvania and West Virginia contain 57% of these threatened areas, with the remainder being spread out over 16 states (Johnson and Miller, 1979). Events of subsidence have been reported in urban areas, including Pennsylvania (Gray et al., 1977) and Illinois (Mahar and Marino, 1981). One location has observed three episodes of subsidence beginning in 1950 (Bruhn et al., 1981). These subsidence events all occurred over abandoned room-and-pillar mines. Some mines have been abandoned more than 50 years (Bauer and Hunt,1981) . Available research does not offer much on the problem related to time dependent subsidence, especially those associated with the failure of remnant coal pillars. The physical modeling technique developed at West Virginia University is capable of measuring both instantaneous and time delayed subsidence. Laser Holographic Interferometry Laser holographic interferometry, or holometry, uses the interference properties of laser light to measure small movements of objects. The object requires only optical access and no surface instrumentation. This technique is closely related to photoelasticity. Both techniques rely on the uniqueness of the light reflected off or through an object in any given state of stress. The entire measurement process is done remotely without any surface instrumentation and without using a camera. The interferogram is constructed and visual observation will yield fringes on all areas that yielded or moved. The displacement represented by one fringe was determined by Wilson et al. (1977) and is given by the relationship: [d ='1(1) 2 cos 8 where d = displacement of one fringe 6 = incident angle of laser light A = wavelength of light (632.8 x 10-9 meters for Helium-Neon lasers)] In summary, holometry is capable of detecting very small movements of objects under study. It is a very sensitive process that requires laser light and vibration free experiments. Experimental Program Lab Facilities The primary components of the facilities were the laser and the optical table. The light source was 50 milli-watt, Helium-Neon laser. The optical table was a granite slab weighing nearly one ton. All experiments were performed on the optical table. It consists of a large table sitting on air cells similar to car innertubes. Six air cells were placed on top of two layers of wood and Styrofoam. Figure 1 is a schematic diagram of the vibration free table. Even with these precautions, the experiments still had to be performed at night to reduce potential traffic related vibrations. Room-and-pillar mine models consisting of three different pillar sizes were constructed out of plexiglass. The models were designed to represent three different extraction ratios. Figure 2 shows the models. The extraction ratios were determined by the tributary loading concept (Peng, 1978). These models were the primary component of a seam extraction simulator. A schematic of this simulation device is shown in Fig. 3.

Jan 1, 1986

By Charles H. Morgan

THE case of Henry Cort comprises: (1) the nature of Cort's inventions;, (2) their value to England and to mankind,; (3) the remuneration received therefor by him or his family; and (4) the suitable permanent record and recognition of his services by the representatives of the art lie founded-a debt long over-due, and still unpaid. I. CORT'S INVENTIONS. Under this head, it is unnecessary here to enter into details. The facts have been repeatedly published, and a brief outline of them will be sufficient for my present purpose. . Henry Cort, born in 1740 at Lancaster, England, became a navy broker in. London about 1765, and gained from that business in about ten years. something more than £20,000, which lie devoted to perfecting the manufacture of iron, building a mill at Fontley, near Portsmouth, and prosecuting, between 1777 and 1783, the experiments which culminated in .his two patents, one for puddling iron and the other for shaping it by rolling between grooved rolls.: Careful study of the contemporary evidence, including Cort's specifications, the testimony (in act as well as word) of his business rivals, the public declarations of eminent authorities, and the history of the times, leaves no possible doubt that Cort was the real inventor, of

Mar 1, 1905

By John T. Thorndyke

MOST important of the naturalcalcium silicates is the meta¬silicate, CaSi03, known as wollastonite, after W. H. Wollaston. A large deposit of this mineral was dis¬covered some seven years ago near Code Siding, Rademacher mining dis¬trict, Kern County, Calif., the deposit being some 7500 ft. long and of an average width of 300 ft. It consists of a series of small domes striking north¬erly and southerly and with a dip of 81 ° to the south. This deposit was opened up by a series of small quarries showing a potential tonnage of 12,000,¬000 tons, allowing of cheap mining and transportation, the Southern Pa¬cific R.R. spur track being one mile north of the workings. Numerous sam¬ples taken from different points on the deposit, tested by Mr. Brinker, of the California Testing Laboratories, Los Angeles, showed an average as fol¬lows: Per Cent Silica (SiO2) 47.12 Lime (CaO) 41.72 Magnesia (MgO) 2.72 Alkalies (R,0) Trace Iron (Fe.,O,) 1.60 whereas the theoretical composition of of wollastonite, as given by William Shirley Bayley, is as follows: Silica 51.75 Lime 45.25 The tonnage and purity of this de¬posit led to investigations into its com¬mercial development. Early work es¬tablished the fact that wollastonite was ideal for the manufacture of a tough, almost unbreakable, glass similar to Pyrex. It also established the fact that wollastonite was particularly adapted for use in the manufacture of mineral wool, towards which further research was then directed. Briefly, the prin¬cipal advantages were the substantially unvarying chemical composition of the naturally occurring mineral and its characteristic of being relatively flexi¬ble and highly resilient when fused into a glass. A mineral wool produced therefrom is thus not only of highly uniform composition and color but is most desirable because of the high mechanical strength and length of the individual fibers constituting the wool. It is well known that mineral wool may be prepared by melting a suitable charge of raw material and then intro¬ducing a stream of a suitable fluid, such as air or steam, into a stream of the molten raw material. By this means the molten material is blown into threads or fibers, which are collected in a suitable chamber similar to a tun¬nel, from which they are removed from time to time or continuously. Com¬mercial manufacture of mineral wool has been carried on for only about 50 years, but volcanoes, specifically Kilauea in the Hawaiian Islands, have

Jan 1, 1936

By E. Miller, K. L. Komarek

Equatiorzs have been derived which related maximum solid solubilities in semicondcting compounds having retvograde solidus curves with 1iqllidus data. Liquidus curves in Lke Pb-Te, Pb-Se, ard PB-S systetris have been defermined by thertrzal aralyses. Fvotrz expevimental maximum solibilities ia CdTe, PbTe, uxd PbS vetvograde tetrperatures hale beep1 calculated. TIze resllts support the concept that under certaiz conditiots pronounced itjlections in the liquidis curves arc indzcatiz:e of retropade solidus curves and that the tenlperatltre of the lmaximum solid solubility will be close to the temperature of the point of inflection in the liquidus curve. The maximum solid solihility within a gvoup of homologous cottrpoods SeetlLs to increase with increasing flatness ol the liquidus curvres. The phenomenon of retrograde solubility in metals, i.e., maximum solubility in a solid terminal phase in equilibrium with a liquid phase, has been theoretically predicted by Van aar' in his calculations of hypothetical binary phase diagrams. It was not until 1926, however, that retrograde solubility was experimentally verified in the Zn-Cd system.' Since then many sys- tems with retrograde solubility have been found, so that at present approximately fifty binary diagrams with a retrograde solidus curve are known.3 Meijering4 has critically appraised the accumulated data and has presented calculations which alloy predictions as to whether or not a solidus line will be retrograde. Interest in retrograde solubility increased when it was found that the solidus curves of germanium and silicon alloyed with a great many doping elements are retrrade. The problem was treated thermody-namically by odkinson,% d all available data on solid solutions in germanium and silicon were summarized by Trumbore.7 Although it is to be expected that intermetallic compounds will also exhibit retrograde solubility, experimental evidence is much more limited. Until now retrograde solidus curves have been reported for the compounds de,' be, Ps:" ne," SnSe," and SnS.13 All these compounds are semiconductors, and the solidus curves were usually obtained by determining the carrier concentration at room temperature of samples equilibrated at elevated temperatures and then quenched. It has been hown,'' however, that it is not always possible to quench in the equilibrium compositions from above a certain temperature. Theoretical discussions have either explicitly excluded intermetallic compounds4 or not treated them with respect to retrograde slubilit.j In the following a thermodynamic treatment of retrograde solu-

Jan 1, 1967

By M. Metzger, L. E. Hendrickson

Grain boundary attack in 16 pct HCl was found to be substantially the same at low penetrations in zone-refined aluminum (individual impurities 0.1 at. ppm), superior electrolytically refined aluminum (51 at. ppm), and aluminum with various impurities at much higher levels. It was concluded that impurity atom segregation affecting corrosion would have been detected and that the corrosion susceptibility did not originate in this segregation but in the structure of the boundary. It was pointed out that the significance of most previous studies in this system had been obscured by an unrecognized autocatalytic copper reaction. Although general corrosion rate was also impurity-insensitive , there was shallow pitting attributed to iron seg-regation and a hillocked surface texture associated with copper; these were interpreted as due to cathodic damage affecting- cathode distribution. THE grain boundary corrosion suffered by high-purity aluminum in hydrochloric acid has been the object of some interest (the earlier work is summarized in Ref. 1). The central metallurgical question here is whether the corrosion susceptibility of a boundary originates in its structure or in impurity atom segregation. An attempt to study this question revealed large catalytic effects associated with small quantities of the copper impurity in the aluminum, 220 ppm, or in the corrodent, and these magnified the preferential boundary attack and obscured the intrinsic susceptibility question.' After the catalytic effects had been examined,"' test conditions could be designed to avoid them and methods developed for studying the shallow boundary penetrations prevailing when they were absent.= It then became possible to determine whether intrinsic boundary corrosion in aluminum involves impurity segregation. The older work provided no firm information on grain boundary segregation of specific solutes influencing corrosion although several studies suggested iron segregates.4,5 perryman4 found in 10 pct HC1 that the slowly developing (microns per month) grain boundary grooves were deeper in material of higher iron content (range 10 to 550 ppm, with 5 to 80 pprn Cu) but he did not measure the depths of general corrosion, which were probably several times greater, and his reference surfaces may have varied more than did the groove depths. Metzger and Intrater's results for 20 pct HC~,' which yielded higher time-average rates (mm per month) and deeper penetrations, suggested that boundary segregation of iron (range 4 to 230 ppm, with 22 pprn Cu) decreased the penetration rate. However. in the stronger acid the autocatalytic l.E. HENDRICKSON, Student Member AIME ,and M. METZGER, Member AIME, are Research Assistant and Professor of Physical Metallurgy, respectively, Department of Mining, Metallurgy and Petroleum Engineering, University of Illinois, Urbana, Ill. Manuscript submitted March 11, 1968. IMD effect of the copper impurity is greater1,2 and it is now evident that their corrosion rates had been much magnified by this effect and did not provide a proper basis for the analysis of segregation. In exploratory studies of other solutes (made under the same conditions), 1000 ppm additions of Mg, Mn, or Si or 100 ppm Ca were without effect.1 Montariol6 noted that boundary attack in 22 pct HC1 persisted after zone refining although with fewer deep fissures (ranges 0.06 to 4 ppm Cu, 4 to 23 ppm Fe). Autocatalytic effects may have influenced these results also and those of Perryman.4 The present objective was, as a first step, to see whether quantitative tests designed to exclude autocatalytic influences would indicate the existence of low-level impurity effects on intrinsic boundary corrosion. Comparison of electrolytically refined with zone-refined aluminum of lower copper and iron contents revealed no differences in boundary corrosion, but certain impurity-sensitive differences in general corrosion morphology were noted and investigated further at higher impurity levels. I) EXPERIMENTAL PROCEDURE A) Material. A selection from commercially available material was made with the cooperation of several producers. An electrolytically refined lot (III-A, 1 ppm Cu, 2.4 ppm Fe) studied previously3 provided a starting point. Since material of substantially higher copper content could not be used if the autocatalytic corrosion reaction were to be avoided,2,3 a lot (III-B) of about the same purity was added as a check, two zone-refined lots (I-A and I-B) with copper and iron an order of magnitude lower were selected for comparison, and an intermediate lot (11) was included. Analytical data are given in Table I. For copper in I-B and iron in I-A and I-B, the actual concentration is thought to be near the limit given, i.e., about 0.1 ppm. For titanium, vanadium, and chromium in III-B, the actual amounts are thought to be, like those in III-A, substantially lower than in the zone-refined lots (these elements concentrate in the solid on freezing). Data are given later for some additional lots surveved. B) Specimen Preparation and Procedure. one by 3 cm blanks with a notched stem were cut from 1-mm cold-rolled sheet, annealed 24 hr in air at 650°C, and quenched in an air stream (42°C per sec initial cooling rate, 100 sec to cool to 100°C). The high annealing temperature maximized diffusivities and approach to equilibrium impurity distributions. A water quench, in principle more efficient in preserving the distribution established, was undesirable because the boundaries were almost plane and they tended to shear and migrate during the quench and thus to be separated from any existing impurity atmosphere. Test procedures, previously described,3 involved electropolish-ing, etching 2 min in 10 pct HF at 24.0°C, and expos-

Jan 1, 1969

Jan 1, 1929

By J. H. L. Vogt

TABLE OF CONTENTS. PAGE Introduction,...........125 I. The Original Source of the Heavy Metals of Ore-DepoBits,. 126 Distribution of Elementary Substances in the Earth's Crust,. . 128 11. The Relation between Eruptive Processes and the Formation of Ore-Deposits, Especially Buch AS have been Produced by Eruptive After-Actions,........ Ore-Deposits Formed by Magmatic Segregation,..... Ore-Deposits Formed by Eruptive After-Actions,..... Cassiterite-Veins and Apatite-Veins,...... Ore-Deposits of Contact-Metamorphic Origin,.... Pyritic Deposits,.......... Veins of Gold, Silver and Lead-Ore,......142 Conclusions,........... 111. The Nature of the Ore-Solutions in Vein-Fissures, and the Metasomatic Alterations along the Ore-Veins,. .. 147 The Association of Vein-Minerals,.......147 Deposition of the Vein-Minemls,........148 Alteration of the Country-Rock,........ Classification of Metasomatic Alterations,...... 149 Additional Observations,......... Kaolinization,..........150 Comparison between Cassiterite-Veins and Lead-Sulphide Veins,. 154 Comparison between Formation of Greisen, etc., and Propylitiza tion, etc.,........... Conclusions,........... IV. Differences of Depth in the Original Positions of EPIGENETIC Deposits ; and the Secondary Alterations of Deposits,. . 158 Original Differences of Depth,. .. .. .. . Gecondary Altemtions of Ore-Deposits,......, Introduction. In the latter part of November, 1900,I received through the Secretary of the Institute the papers of Messrs. Van Hise, Emmons, Lindgren and Weed, presented at the Washington meeting of February in that year, with the request (urged also by Mr. Emmons) that I would furnish for the Richmond meet-

Jan 1, 1902

By Carl Scholz

Discussion of the paper of Carl Scholz, published in Bi-monthly Bulletin, No. 22, July, 1908, pp. 551 to 559. HOWARD N. EAVENSON, Gary, W. Va. (communication to the Secretary*) :-For some time before the publication of Mr. Scholz's paper, I had been collecting data bearing upon its subject, and I now take pleasure in presenting my results to the Institute in the form of a discussion. It has long been a matter of common opinion among mining-men that mice-explosions are, more frequent during the colder, or winter months, than during the warmer ones, and it is a matter of common knowledge among them that the air-ways and road-ways in most mines are much drier and are more in¬clined to be dusty during the winter than during the summer. In many mines, places which are wet and sloppy in the summer are dry and sometimes dusty during the winter. These changes, of course, can only be due to atmospheric conditions, and are caused by differences in temperature and humidity. Until recently, however, very little attention has been paid to the part that atmospheric conditions may play in mine-explosions, or, rather, to the effect they may have in rendering mine-conditions peculiarly dangerous, and in spreading and rendering more disastrous the effects of what would otherwise probably have been .small explosions. To show the difference in mine-conditions during sunnier .and winter months, I have tabulated in Table I. the results of 24 observations of hygrometric conditions in several different mines at different times of the year. Mines Nos. 1, 2, and 6 are located in the Pocahontas.coal -region, in McDowell couuty, W.Va., the first one being a shaft-mine shaft mine and the others drift. Mines 1A and 2A are drift-mines located in Logan county, W. Va. All of these are mines of fair size, but none of them has been in operation more than six years,

Jun 1, 1909

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

The effect of such variables as feed size, particle shape, cleavage, and hardness on the relative proportion of impact, abrasion, and chipping events in a tumbling mill is demonstrated. The concept of an average event, which is a combination of the three comminution mechanisms, is introduced. It is postulated that the average event in a particular mill determines not only the size distribution but also the energy-size reduction relationship for the comminution process. Fragmentation of particles in tumbling mills appears to result from a combination of impact, abrasion, and chipping grinding.' The relative rates of size reduction attributable to any of the basic grinding mechanisms must depend upon a number of variables, such as feed size, particle shape, hardness, and the number and kind of particles in the mill. The purpose of this paper is to show experimentally how these variables in the properties of materials affect the size distributions obtained by grinding the material's in a laboratory tumbling mill. The resulting size distributions will be intetpreted in terms of a combination of three comminution mechanisms. METHODS AND MATERIALS In this study, minerals of widely differing properties were ground either separately or as mixtures in laboratory mills using rods or balls for grinding media. The materials used include quartz, Tuolomne, limestone (99.8% CaCO3), barite, corundum, galena, pyrite, glass beads, and crushed glass. The mill used was 8 in. in diam. and 9-1/4 in. long. For the ball milling tests, 17.6 kg of steel balls (36: 7/8 in. balls, 178: 1 in. balls, and 44: 1-1/8 to 1-1/4 in. balls) were used. For the rod milling experiments, 17.6 kg of steel rods 9-1/16 in. long (25: 5/8 in., 10: 3/4 in., and 5: 7/8 in. in diam.) were used. In each test, 1 kg of solids were ground wet at 60% solids at 77 rpm. In all cases except where otherwise specified, the feed to the mill was 4 x 8 mesh material. Size distributions of the ground products were determined by a wet-dry sieving procedure with Tyler series sieves. Size distributions of mixed products containing limestone were determined by dissolving the limestone with acid and sizing the residue. EXPERIMENTAL RESULTS AND DISCUSSION If the size distribution of the product from a tumbling mill depends upon the relative proportion of impact and attrition (abrasion and chipping) events, altering the grinding conditions may change these proportions and consequently alter the size distribution of the product. Data to illustrate this point can be taken from Gaudin's classic 1926 paper.2 In one series of experiments, Gaudin ground quartz of different initial sizes for four hours in a laboratory ball mill with 7/8-in. balls. In Fig. 1, his data are reproduced as the cumulative fraction finer than the stated size for the following initial feed sizes: 13.3 x 9.4 mm, 6.7 x 4.7 mm, 2.6 x 1.6 mm, and 0.83 x 0.59 mm. As the feed size was decreased, a dramatic change in the shape of the size distribution curves took place, even though the amount of minus 100-mesh

Jan 1, 1964

By W. Armstrong Price

INVESTIGATION by German chemists during the World War showed that particles of iron oxide form rapidly in iron pipes carrying hydrogen gas under pressure when the gas contains small amounts of water. Under these conditions, the gas frequently exploded when expanding into a dirigible. The explanation of the explosions lies in the building up of a charge of static electricity in the flow just beyond the orifice and the ignition of the gas by a spark accompanying discharge of the electricity. Friction between the moving particles and the pipe generated the electric charge, which was manifested by a pale blue glow formed in the flow at pressures above two atmospheres. In one experiment, this glow, at eighty atmospheres, extended for a distance of forty to fifty centimetres, but did not ignite hydrogen and air mixtures until the charge was col-lected by a conductor and discharged across a gap between electrodes placed at the side of the column of gas. Autoignition did not occur when this discharge was effected at a distance from the gas column, nor if the gas used was thoroughly dried and free from impurities. The electric charge has been studied by placing various wire and screen conductors in the outcoming stream of gas, Guest having summarized these experiments. The application of these conclusions to fires in petroleum and natural gas issuing uncontrolled from wells is made in the following paper, citing the ignition of a wild gas well in Texas.

Jan 1, 1936

L. D. GODSHALL, Everett, Washington: This very interesting paper cannot fail to command the attention of every one who has ever had experience in the amalgamation of gold-ores. I wish to call attention to three very important facts brought out very prominently by the paper, namely: 1. The extent of accumulation of amalgam on copper plates in the form of scale, not removable in the ordinary manner; 2. The change in the relative quantity of the two metals in the amalgam as we. recede from the battery-discharge; 3. The difference in fineness of the bullion obtained from the above-mentioned scale as compared with the bullion from the daily clean-ups. From Mr. Bayliss's figures we find that during the life of the plate in question 14,942 tons of ore were crushed, yielding amalgam of the value of $5.03 per ton, or a total value of $75,158.26. The amalgam accumulating on the plate during this time as scale, we find to have had a value of $8340.54, or $0.558 per ton of ore treated, representing 11.09 per cent. of the total amount of amalgam saved in the ordinary clean-up; or, taking the amalgam saved by daily clean-up plus the amalgam-scale as representing the total saved on this plate, or 100 per cent., we find that the daily clean-up saved 90.01 per cent., while the scale represented 9.99 per cent. The above figures do not include some additional amalgam still adhering to the plate after scale had been removed. We are told that this was not an exceptional case at the Drum Lummon, but that other plates have even yielded a third more than the one in question. The interesting query now comes up, whether this experience at the Drum Lummon is exceptional or universal at all mills; and another question arises, as to how long such an accumulation might continue,

Jan 1, 1897

By D. B. Hobbs, L. W. Kempf, R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13 per cent. of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 25S, Special 17S and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings. REVIEW OF LITERATURE The literature on the heat treatment of aluminum-silicon alloys is not very extensive. The following review gives the principal references of which the authors are aware, in which appreciable information may be found.

Jan 1, 1928

By R. E. Hudrlik, G. W. Preckshot

The diffusion coefficients of silver from solid silver in molten lead were measured to within ± 0.8 pet in a columnar type diffusion cell ower, the temperature range of 326° to 530°C. Fick's law describes the process up to 530°C where the laminar mechanism appareltly breaks down. These is negligible resistance at the interface as shown by mathematical analyses. The diffusion coefficients are found concentration independent. IT would seem that diffusion in liquid metals would be free of such effects as molecular structure, dissociation. polarization. and compound formation. This view was taken by Gorman and preckshot in their study of diffusion of copper from solid copper into molten lead. They reported diffusion coefficients which were independent of the concentration over the range of 478° to 750°C. They found that the Stokes-Einstein equation with constant radius of the diffusing specie represented the diffusion data better than Eyring's rate theory equation and Sheibel's correlation. The radius of diffusion was found to be that of the doubly charged copper. There appeared to be no resistance across the solid-liquid boundary. In the present work the diffusion coefficients for silver in liquid lead were measured over a range of temperatures of 350° to 505°C. The solubility of silver in lead over the range of 303° to 630°C was also obtained. These results are compared with calculated or correlated values or with data in the literature. EXPERIMENTAL Procedure—The experimental equipment techniques and procedures were those reported in detail by Gorman and preckshot9 and will not be repeated here. Measured values of WT, Co, A. L were obtained for various diffusion times and the diffusion coefficient was computed for the case of no resistance at the interface9, 11 by: WT/CoAL = 1- 8/p2 n=1 1/(2n - 1)2 exp[-(2n - 1)2p2 Dt/4L2] [1] or where there was resistance at the interface by: WT = 1- ?n=1 2h2/ap2L [sxp [-Dan2t]/[(h2 + an2) L + h] The roots an are those of the transcendental equation3 tan (an L) = Iz/cun. The diffusion coefficient is that defined by Hartley and Crank.7 The total silver in the lead cylinder and equilibrium slug was determined by a cupellation technique' with proper correction for losses. Analysis of known samples showed that this method is surprisingly accurate. The amount of silver in the lead adhering to the silver cylinder was obtained in the same fashion as shown by Gorman and preckshot.9 The small errors involved in this determination are not critical since the silver in this adhering lead layer is only 3 to 15 pet of the total diffused. Materials—Electrolytic silver containing 99.9+ pet Ag obtained from General Refineries of Minneapolis, Minn. was used for all but runs 7 and 8. For the balance of the runs this silver was reduced with hydrogen at 1100°C and its oxygen content was found to be about 0.017 pet. For the runs. 7 and 8, phosphorous-reduced silver of the same purity was obtained from Handy and Harman Co. of Chicago, Ill. The densities of the phosphorus-reduced silver and the hydrogen-reduced electrolytic silver were 10.484 and 10.487 g per cm3, respectively. These values agree with those reported for pure silver. Silver which was reduced at 900 C had an average density of 9.998 g per cm3, indicating porosity. This silver was used for a number of runs which were not tabulated in Table I. These are indicated by crosses on Fig. 2. The 99.999 pet Pb was obtained from the National Lead Co. Research Laboratory of Brooklyn, New York. DISCUSSION OF RESULTS The diffusion and solubility results are reported in Table I for eleven runs using either phosphorus-reduced electrolytic silver or hydrogen-reduced silver at 1100° C. The solubility data shown in Fig. 1 show the excellent agreement with that reported by Heycock and Neville.8 The data of Friedrichs5 apparently are in error. The experimental solubility data of this work are reported to 0.3 pet. The experimental diffusion coefficients computed from Eq. [1] are reported within 1.2 pet of the mean and are plotted in Fig. 2. These are expressed within +0.8 pet of the experimental values over the entire temperature range by: D= 8.26 x 10 -5 e-1925/RT . [3] There appears to be little difference due to the

Jan 1, 1961

By David C. Jonson, W. Bruce MacKenzie, Arthur A. Bookstrom, Vaughn E. Surface, Neil K. Muncaster, Stewart R. Wallace

In mid-Tertiary time a wet silici-alkalic magma penetrated the Precambrian rocks of what is now the Tenmile Range of Central Colorado and formed the Climax Stock. The stock is a composite one and was intruded in four separate irruptions, each giving rise to a major hydrothermal event. The first three of these produced large stockwork ore bodies that cap and flank the tops of their respective source intrusives; the fourth, and last, yielded almost no commercial mineralization. The ore bodies and their related zones of alteration are circular to ring-shaped in plan and arcuate in section. The different phases of the stock are so positioned with respect to each other that many of the circular and arcuate zones of mineralization and alteration overlap or are juxtaposed. Evidence of a time separation between the different ore bodies is found in certain dikes that were intruded between periods of mineralization and are well mineralized in one ore body but are barren in another. If it is assumed that the parent magma at Climax contained 10 per cent "water," that the "water" contained 0.1 grams per liter of molybdenum, and that the processes of extraction were 100 per cent efficient, then approximately 10 cubic miles of magma would be required for the formation of each ore body. The volume requirements, taken in conjunction with the cross-sectional areas of the different phases of the stock to explored depths, suggest to the authors that each magma chamber was columnar, extended to a depth of thousands of feet, and was connected with a much larger master reservoir. The repetition of similar intrusive, structural, and hydrothermal events, indicates periodic tapping of this reservoir. A regular chemical evolution of the parent magma is suggested by the systematic change in metal ratios and differences in the sites of deposition, relative to the source intrusive, in each of the four separate igneous hydrothermal stages. The preparation of ground was due to changes in magmatic and/ or hydrothermal pressures within the igneous-hydrothermal columns; small, repeated, up and down movements of the rock enclosing the tops of the columns formed the stockwork fractures into which the mineralizers penetrated. The forceful emplacement of each successive phase of the Climax Stock resulted in a slight doming and rotation to the westward of the earlier-formed geologic features. Postore normal displacement along the Mosquito fault is estimated at about 9000 feet. Part of one ore body was cut by the fault and lies at depth below the Paleozoic sedimentary strata on the hanging wall. On the footwall side of the fault, subaerial erosion and glaciation removed a large part of one ore body and uncovered the top of a second.

Jan 1, 1968

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963