Search Documents

By A. H. A. Robinson

Until quite recently-practically up to the present time-all but an insignificant amount of the copper produced in Canada was shipped abroad in the form of ore, matte, blister, etc., there to undergo the further treatment necessary to bring it to the refined state in which it is required by fabricators of copper. Consequently, Canadian manufacturers were forced to import nearly all the copper required in their business; and a considerable portion of the ultimate value to be derived from a Canadian raw material was lost to the country of its origin. In the early days of Canadian copper mining, when both the production and consumption of copper in Canada were much smaller than now, such a condition of affairs was perhaps economically unavoidable, and, in any case, was not a matte~ of sufficient importance to attract general attention. Later on, however, when there had been large and rapid increases both in the production and consumption of copper in Canada, it formed the basis of much adverse criticism, deserved or not, of producers of Canadian copper-criticism that became intensified during the war and subsequent years. Happily, the chief grounds of complaint have now been removed, and there are today copper refineries in Canada, either operating or under construction, that are capable, in the aggregate, of turning out amounts of refined copper greatly in excess of any indicated Canadian consumption.

Jan 1, 1931

By Robert C. Merritt

Laboratory amenability studies as well as a pilot heap-leaching investigation of low-grade sandstone uranium ores from Wyoming, New Mexico, and Colorado are described. Sulfuric acid heap leaching with oxidation, for 120 days, extracted up to 98 percent, 90 percent, and 79 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively.

Jan 1, 1976

"M bed, Matanuska valley, Alaska, coal carbonizingproperties B 510M spectral lines, low-energy, study RI 5538Mab shaft, Leadvile district, Colo., investigation RI .1518Maberry process, for aluminum chloride TP 321"

Jan 1, 1960

By K Morrison

Australia’s ageing population means that by 2050 there will be 2.7 people of working age to support each Australian aged 65 years and over compared with five working people per retiree today and compared with 7.5 in 1970 (Swan, 2010). This means that there is going to be a greater demand on social services – for medical and aged care – from a smaller private income base. How will this gap be met? Australia is fortunate in that it has vast resources of mineral wealth; from iron ore, nickel and gas in Western Australia to the giant copper and uranium deposits at Olympic Dam in South Australia.The prospect of a meaningful profit based tax on this vast mineral wealth has been lost through Australian government’s handling of the issue in 2010 and with an industry fiercely opposed to the prospect of a mining tax. Hence, new ways of thinking are required. This paper looks at the issues facing the implementation of a novel scheme whereby Australia leases the mineral resources it extracts and thus derives income over the decades the metals are in-use in pipes, wires and structures with a premium paid for unreturned material or that used in dissipative applications. Applicable minerals could include copper, aluminium, nickel and rare earths. If Australia simply digs up and sells the metals once, the buyer becomes custodian of that resource and they benefit from controlling the future ‘above-ground’ resource stock.A complementary driver for a leasing scheme is the increasing importance of chain-of-custody following initiatives of the Responsible Jewellery Council with gold and diamonds, now with the potential to extend across commodities. The Australian minerals sector could thus position itself as a premium supplier with high social and environmental credentials.Recognising the implementation challenges, this paper includes a review of how such a system could be enforced to ensure that the metal is tracked throughout its life. It concludes with a discussion of the rates and terms should such agreements hold and suggestions for institutional arrangements for enforcing compliance.

Nov 22, 2011

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By A. L. Podia

The purpose of this research was to develop a system capable of detecting changes in the structure of rocks, leading to failure of mine roofs, and/or excavations. A prototype system was developed, field tested and delivered to the United States Bureau of Mines for further evaluation and research. This system is based on the analysis of acoustic signals generated on the surface of the roof by an impact device and which are reflected or backscattered by flaws and discontinuities in the rock. The specially designed impact source is capable of generating high frequency acoustic signals with excellent repeatability. The system can also be used in conjunction with conventional acoustic pulse transducers. The received signal is digitized and the data transferred to a minicomputer for processing and display. This capability allows the immediate determination of wave velocity and/or distance to a reflecting interface. Various data processing techniques such as averaging, differentiating, and comparing of different signals can be selected by entering the appropriate commands on the keyboard. Being a programmable system it is possible to implement more advanced signal processing techniques. All results as well as the signal are displayed on a CRT. Furthermore, a permanent record of the data can be generated on paper tape, which can be reentered and processed at a later date. A communications interface allows transmission of the sampled signal to a large scale re-mote computer. The system was tested extensively in the laboratory, and field tested at the York Canyon Coal Mine. These tests proved the feasibility of operation in the mining environment. Results indicate that further investigation and development will have to be undertaken to fully develop the potential of this system in satisfying the goals of this research.

Jan 1, 1973

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used fur making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964

By Henry Kreisinger, WALTER T. RAY

This preliminary bulletin was written as the first of a series of several on the significance of drafts in steam-boiler practice, the succeeding bulletins to be along the same lines but of a more advanced character. The conclusions arrived at are tentative, and are the result of a study of one of the many problems growing out of a general plan of the United States Government to increase the efficiency with which the coals of the country are being used. Greater efficiency requires better boiler and furnace design. The experimental study of drafts on which the conclusions presented in this bulletin are based formed part of the fuel-testing investigations that were carried on by the technologic branch of the United States Geological Survey and have been transferred to the Bureau of Mines. The experiments made seem to indicate that it is possible to double or treble the capacity of a plant without making any radical changes the furnaces and boilers. These increases require about double and treble the quantities of air to be put through the fuel beds and boilers. It also seems probable that rebafHing the boilers will often permit the capacity to be doubled or trebled, while still getting more steam than formerly per pound of coal for uses outside the boiler room. These experiments were undertaken with the object of clarifying ideas concerning the passage of air through fuel beds and boilers. Measured weights of air were passed through two beds of lead shot, series, one of which remained always the same and represented a boiler; the other being varied as to size of shot and depth of bed, and representing a fuel bed. Careful observations were made of the weight of air passing through the beds per minute. All data were plotted in many charts, so as to permit the study of them from several points of view. A number of laws were deduced bearing on the relative amounts of power required to force air through fuel beds of various thicknesses, composed of various sizes of coal, and through boilers of various lengths and areas of gas passages. An important part of the discussion relates to an increase in the capacity of boilers by increasing the amount of power applied to pressure and exhausting fans and thus forcing several times as much air through the fuel beds and boilers. may be possible, as a result of these investigations, to raise the rate of working the boiler heating surface to three or even four times its present value. Such an increase would undoubtedly mean new designs of grates, stokers, furnaces, and boilers, especially fitted for high rates of working. Fan equipments designed to supply three or four times as much air under several times the pressure would be provided with more efficient engines, thus giving an additional factor favoring high-capacity working. It must be borne in mind, as stated above, that the results are tentative. It will cost money to force gases at high speeds through fuel beds and boilers, and there will soon be pressing need of such quantitative data as will enable the largest possible part of the energy imparted by the fans to be advantageously utilized. We desire, to thank our superiors, especially Messrs. L. P. Breckenridge and D. T. Randall, for their helpful criticism and suggestions.

Jan 1, 1911

By J. N. Geyer

During the early stages of the mining industry of the United States an apparently inexhaustible supply of high-quality, easily accessible coal made the product cheap and the attendant mining methods wasteful of recoverable coal. Because coal from advance places could be mined with less effort and a large outwit obtained as the entries advanced, much of the coal left in pillars to support the roof was lost. Squeezes often developed in these mined-over areas, or, if pillars were of sufficient size to-prevent squeeze, the roof would be so weakened by long exposure that any pillar recovery was extremely hazardous. As the value of unmined coal increased, a high recovery of the available coal became necessary. Numerous plans were tried during the period that followed, some of the methods proving successful while others were complete failures or only partly successful. As a better knowledge was pained of the roof strata and its behavior, however, pillar mining became more successful and methods suited to special roof conditions were developed.

Jan 1, 1933

By C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent in improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silver- bearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores that because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Jan 1, 1965

By Primak. George J.

"In the development of a new product as well as during its introduction on the market, it is very important to give due consideration to problems involving patents, licenses and trade marks. At the very beginning of the research and development program, it is obviously essential to ascertain, through a suitable patent search, that the product in question will not infringe any patents which are still in force. Then, a possibility of achieving one's own patent or proprietary position on the product or the process of its manufacture should be carefully explored. Licensing arrangements that one may reach with respect to patents and know-how covering such new product may, in the final analysis, determine its over-all success or failure. If one can count on licensing revenues or some favourable cross-licensing arrangements with respect to a newly developed product, this may go a long way to achieving profitability and success. The selection of a good trade mark is probably one of the most important acts that one has to perform once the product is developed, as customers will identify the new product by such a trade mark. In many instances, successful marketing and widespread acceptance of a product are largely due to its appealing name or trade mark, accompanied by proper promotion and advertising. Once the trade mark has been adopted, it should be registered in the Trade Marks Office to provide the protection afforded by federal statute. If the product is to be manufactured, sold or licensed in some other countries, similar considerations should be made with regard to each such country."

Jan 1, 1973

During the hydrometallurgical processing of the major base metals Cu, Zn, Ni and Co, the presence of iron is normally a serious complication, and iron separation from the pay metals usually constitutes one of the main challenges for the metallurgist. There are many instances, however, where the presence of iron is beneficial, or is even required. Two cases are presented where iron is required during the processing of base metals. The first example deals with the use of ferric sulphate to oxidize sulphides, more particularly copper and zinc sulphides, under atmospheric conditions. The results presented confirm that ferric ion leaching is efficient, particularly when the oxidant is regenerated during the process. The second case is the use of iron to solubilise refractory cobalt oxide minerals; examples, including pilot plant results, are presented for various ores from Africa and Central America. In both cases, this paper reviews the basic concepts involved and provides details of their application.

Jan 1, 2006

By The Honourable George Prudham

"I AM PLEASED indeed to be present with you here today and to be taking part in the proceedings of your convention. You have been greeted and welcomed to the Province by Premier Manning who is also provincial Minister of Mines and Minerals, and to this City by Mayor Hawrelak. As Minister of Mines and Technical Surveys in the federal government and as Member of Parliament for Edmonton West, I have been asked to share the honour of extending greetings and a cordial welcome to all.It is a happy coincidence that this representative national gathering, indicative of the growing strength and significance of a great basic Canadian industry, is taking place in the Macdonald Hotel, the new addition of which marks another important step forward in the progress of this City and district.This happens to be the third national convention of the C.I.M. that I •have had the pleasure of attending and I trust that I am not presumptuous in expressing the hope that I will have the opportunity of attending many more conventions of the Institute in my present capacity.Dr. Kidd has bestowed on me a high honour by asking me to be Co-Chairman of this Inaugural Session of the Convention and thus to share with him the responsibility of presiding over the proceedings of this afternoon."

Jan 1, 1953

By C. A. Heiland

THIS year's review of geophysical activities has a somewhat different complexion than usual. With the ending of the war, the time seems opportune to supplement the customary report on operations and discoveries in oil and mine exploration by a review out-lining the contributions of geophysicists to the. war effort. To give as much space as possible to the latter, presented as Part 2, some of the usual review features have been omitted from the statistical section, given as Part 1 immediately following.

Jan 1, 1946

By R. A. Isberg

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75o coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 1, 1981

By S Worden, A Lee Zhi Yi, E Sellers, G Corder, A Littleboy

The global shift towards decarbonisation is driving competition for the extraction of critical minerals such as nickel, lithium, and copper. To meet this demand, new mines are being developed while mines approaching closure are being reimagined as sites of potential resources. This reimagining challenges how mine closure is being conceptualised. In the conventional case, when a mine reaches the end of its economic life, it is closed or put into care and maintenance until it transitions to the next land use, such as agriculture, native ecosystem corridors, solar farms or integrated eco – precincts (Murphy et al, 2019; Holcombe, 2020) (the authors acknowledge that unplanned mine closures have left a devastating legacy of contamination, safety and cultural heritage impacts). Extracting minerals from closed or closing mines will extend mine life and, therefore, delay relinquishment and transition. In this context, innovative technologies are needed to make mining economically viable. In the first year of her doctoral research on improving stakeholder engagement in mine transitions, Lee Zhi Yi has coined the term ‘mine life extension technologies’ (MLETs) to describe a class of technological solutions that optimise extraction of resources after a mine reaches the end of its economic life. Examples of MLETs include agromining (van der Ent et al, 2015), in situ recovery (Robinson and Kuhar, 2018), and reprocessing or reuse of tailings (Gou, Zhou and Then, 2019). MLET extraction offers several benefits compared with conventional mining processes, such as waste remediation, value recovery of minerals, a smaller footprint and less environmental impacts (Sellers, Picorelli and Salmi, 2022). What requires further investigation is the consequences of MLET implementation to host communities or community perspectives towards the proposed technology and subsequent delays in transition.

Aug 2, 2023

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By Robert McClure, Frederic Leclercq, Ricardo Chavez

With significant vibration control and fragmentation challenges facing them, the CBS quarry (department of the Nord) successfully integrated a technical partner and mine to mill optimisation to deal with a difficult environment. For the last three years, CBS has been conducting a global production monitoring program similar to the mine to mill concept used in the mining industry. This concept consists of optimising the drilling and blasting while monitoring the effects on the downstream chain (vibration control, loading, hauling, crushing, plant output). Blast optimization is ensured by systematic control of the blast geometry (volumes, patterns, bench and face anomalies, drill deviation) and by the use of constant specific energy blasting. Constant specific energy optimises the work of the explosive in a blasting operation and, when combined with a high accuracy programmable electronic blasting system, reduces the impact of blasting on the environment and enhances blast performance. These techniques ensure consistent blasting results and hence improved site productivity. The improvements achieved have been identified thanks to an effective system designed to monitor the key production parameters.

Jan 1, 2007

By E. D. Gardner

This bulletin, which discusses open-cut mining at the metal mines of the United States, is the last of a series of such papers by the Bureau of Mines describing the principal methods of mining.4 Open-cut mining is applicable to flat-lying mineral deposits relatively near the surface. Vein deposits seldom are amenable to this method, although outcrops of veins sometimes are worked as open pits. Most of the iron ore of the country is mined from open pits; according to the Minerals Yearbook, 67.4 percent was mined from open pits and 32.6 percent from underground mines in 1937. Open-cut mining is relatively new in the copper industry but yields more copper than any other method; in 1937 about 52 percent of the copper ore mined in the United States was taken from open pits. Lead-zinc ore has been produced from open pits in the Joplin (Mo.) district, but most of the deposits in this area, although flat-lying, are too deep to be mined economically by the open-cut method. In 1937 one company at Oronogo, Mo., was stripping overburden and mining mixed oxidized and sulfide ores by this method.

Jan 1, 1941

By Milton H. Fies

To present some idea as to how the Bureau of Mines may most effectively serve mining, it is necessary that we make some resume of its pact accomplishments in order to determine what, if any, changes will be of greatest service to the industry and to the nation. There are a great many times in life when one begins to wonder whether or not Emerson, in his famous epigram about "mousetraps" and "beaten paths" and "final recognition of intrinsic worth", took into account the item of time. The intrinsic value of any movement, of any work, of any accomplishment will ultimately be recognized, of that there is no doubt, but may a man in history has gone to his end in martyrdom because the world was slow in the acknowledgement of the true excellence of his worth, and this is likewise true of institutions.

Jan 1, 1934