Search Documents

By J. W. Adams

Two different techniques were wed to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 1, 1974

By P. T. Bloomer

Introduction Mining of the orebody of the Sullivan mine, which is owned and operated by the Consolidated Mining & Smelting Company of Canada, Limited, has reached a point where pillar extraction is rapidly becoming a major part of the operation. Very few of the larger pillars have been completely extracted; consequently, this paper contains much that is theory and expectation. Due to early mining methods and the physical characteristics of the Sullivan deposit, similar conditions may not exist in other older mines facing the problems of pillar extraction, but it is thought that the methods employed and those contemplated may be of general interest. History The Sullivan orebody, which is at Kimberley in the Fort Steele mining division of the East Kootenay district of British Columbia, was discovered in May, 1892, by Messrs. Sullivan, Smith, Cleaver, and Burchett. After passing through the hands of several owners the property was optioned in 1909, and purchased in 1910, by The Consolidated Mining and Smelting Company of Canada, Limited. Early mining was highly selective, the objective being a clean, high-grade silver-lead ore. By 1923 the difficulties of milling the very complex ore had been overcome and the first unit of a concentrator was completed with a capacity of 2,500 tons daily. Capacity was increased by stages to the present rate of 8,500 tons per day. Concentrates are shipped over the Canadian Pacific railway ? to the Company smelter at Tadanac, British Columbia, for final treatment. Approximately 45,000,000 tons of ore has been mined to date.

Jan 1, 1948

The changes in layout and design over 48 years, from the first crushing and shiploading plant installed at Whyalla in 1915, up to the present plant being built at Koolan Island, Yampi Sound may be summarized as follows.1. Smaller motors and lower power consumption have resulted froma. oil lubrication, where practicable, in place of grease,b. a high pressure "oil-lift" device to reduce starting torque in crushers with white metal bearings, andc. roller bearings in place of white metal.2. Short centre drives with pivot-based motors permit controlled loads on bearings and a reduction in size of crusher houses and motor rooms.3. Dust proofing and pressurising of crusher houses and motor rooms reduces working temperatures and improves cleanliness.4. Variable speed pan feeders give improved plant control, with the use of one man only, and remove the need for large surge bins between crushing stages.5. The use of diesel quarry trucks to dump ore through a "drive over"tip results in faster truck cycles.6. Elevated cylindrical silos with air operated chutes, replace long horizontal storage bins with multiple manually operated side discharge chutes for loading rail cars, and give faster and more accurate truck loading. The silos are charged by belt conveyors with automatic distributors.7. Increased shipping bin capacity (40,000 tons at Whyalla and 6O,OOO tons being built at Koolan Island) caters for the bigger vessels now in use and envisaged for the future. Automatic travelling distributors deliver ore to the bins in layers to ensure, maximum mixing and a more uniform grade for blast furnaces.INTRODUCTIONThe Broken Hill Proprietary Company Ltd has six major crushing plants in Australia at its principal sources of raw material. These are at Iron Knob bench G, Iron Knob scree ore plant, Iron Baron, and Cockatoo Island, all of which are ironstone operations. The other two plants are at Rapid Bay, a limestone quarry, and at Ardrossan, which is the Company's only source of dolomite.

Jan 1, 1963

We present a novel hybrid algorithm for quantifying the ore grade variability that has central importance in ore reserve estimation. The proposed algorithm has three stages: (1) fuzzy clustering, (2) similarity measure, and (3) grade estimation. The method first considers data clustering, and then uses the clustering information for quantifying the ore grades by means of a cumulative point semimadogram function. The method provides a measure of similarity and gives an indication of the regional heterogeneity. In addition, grade estimations can be obtained at different levels of similarity using a weighting function, which is the standard regional dependence function (SRDF). Keywords: Grade, fuzzy clustering, similarity measure, point madogram, weighting function.

Jan 1, 2008

Characterizing coal mine roof rock is extremely important for hazard assessment, reinforcement, and entry design. The Coal Mine Roof Rating (CMRR) is an innovative rock mass classification that has found acceptance in the coal mining industry. A disadvantage of the original CMRR is that it cannot be determined in advance of mining, because it requires underground observations. An entirely new set of procedures have now been developed to determine the CMRR from exploratory drill core, as described in this paper. The new procedures employ Point Load Tests (PLT) to determine strength parameters that account for approximately 60% of the rating. Both diametral (parallel to bedding) and axial (perpendicular to bedding) PLT are conducted. The diametral tests allow estimates of bedding plane cohesion and rock anisotropy, both of which are critical to estimating susceptibility to horizontal stress. Traditional core logging procedures are used to determine discontinuity spacing and roughness. To ensure compatibility with the original CMRR, the new rating scales were verified by comparing drill core results with nearby underground exposures. To assist mine planners in using the new CMRR procedures, a large database of strength ratings of roof rocks was assembled through extensive point load testing and logging. Over 2000 point load tests (both axial and diametral) have been made on 30 common coal measure rock types from mines representing most U.S. coalfields. This database has been merged with the popular core rating system of J.C. Ferm into a field guide for geologists and engineers. By using the pictorial classification system of Ferm to identify the rock, typical CMRR can be compared with values calculated using the new CMRR procedures.

Jan 1, 1996

By F. P. Haver

Primary lead is produced in the United States by the pyrometallurgical smelting of lead sulfide (galena, PbS) concentrates, which poses sulfur dioxide and lead air pollution control problems. The Federal Bureau of Mines has investigated an alternative hydrometallurgy procedure that does not generate gaseous sulfur oxides and diminishes the potential for the escape of lead into the atmosphere. The procedure involves leaching galena flotation concentrates with ferric chloride (FeC13) solution to obtain lead chloride (PbC12) and elemental sulfur as expressed by the following chemical reaction: PbS + 2FeC13 ? PbC12 + 2FeCl2 + S°. At 100° C, over 99 pct of the PbS in the concentrate is converted to PbCl2 in less than 15 min. The leach solution, composed of brine (NaCl) containing slightly more than the theoretical required amount of FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. High-purity PbC12 (>99.9 pct) crystallizes from the leach filtrate on cooling and is electrolyzed in a low-temperature, fused-salt cell to obtain corroding-grade metal (>99.94 pct Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride. Other values, such as Ag, Cu, Zn, and S°, are recovered by additional treatment of either the leach solution or leach residue.

Jan 1, 1976

By Jim Frazier

Tradition has often dictated low design load stresses on piles. Such traditions often developed prior to modern static or dynamic pile testing methods and perhaps result from a few limiting situations. These low stress limits were then broadly applied, even in cases where the piles could carry substantially higher loads. With sufficient testing to prove the design, higher design loads may present significant overall savings to the project owner. The cost of the testing then becomes an insignificant cost compared to the potentially great benefit of increased pile loadings. To confirm higher load possibilities for driven piles, the pile is tested either statically or dynamically. Further savings and increased testing efficiency result from remote dynamic pile testing. This paper presents a project where design stresses were considerably increased as a result of additional testing and use of remote dynamic pile testing equipment.

Jan 1, 2002

By O. F. Ochonogor

Laser metal deposition (LMD) is an additive manufacturing technique whereby a stream of metal powder is consolidated by a focused laser beam on the surface of a substrate or engineering component. The interaction zone between the laser beam and powder particles is scanned superficially, generating tracks of deposited material. The tracks are overlapped in a deposition strategy in accordance with slices of a CAD model. Successive layers of material are built up to fabricate a near net shape part. In this work, the technique is used to fabricate metal matrix composites (MMCs) by using an elementally blended feedstock combining metal and ceramic powders in the melt pool, which melt and solidify to create the required morphology. Ti6Al4V + TiC MMCs were produced with 10, 20, and 30 vol.% reinforcing ceramic, and Zr + TiC MMCs were fabricated with 10, 20, and 30 vol.% TiC. The deposited thin walls were analysed using optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and indentation testing. In both systems, the analysis revealed the presence of partially melted TiC particles embedded in the metal matrix along with fine dendrites of re-solidified ceramic. The dendritic structures in the Ti-based composites were confirmed as TiC, whereas in the Zr-based composite the Zr metal reacts with theTiC to form ZrC, leaving Ti in solid solution. Both the MMCs show an increase in microhardness with increasing ceramic (carbide)content, reaching a peak HV0.1 value of 500 in the Zr- based MMC and HV0.1 of 550 in the Ti based MMC.

Jan 1, 2012

By C. Allen

Vale Inco Ltd. is trialing several energy conservation initiatives in an effort to minimize costs and reduce green house gas emissions. The Ventilation on Demand (VOD) concept is a major project being carried out in various phases at Vale Inco mines. Due to the complex nature of a dynamic VOD system, Vale Inco is taking a systematic approach of testing VOD system components with milestone evaluations of each project. Coleman Mine was selected to pilot test the functionality and robustness of automated louvers in the underground environment; with the goal of optimizing mine airflow such that ventilation would be available for developing a new ore body. This project involved installing automated louvers in the exhaust raises; and installing variable frequency drive (VFD) starters on auxiliary supply fans. Because the VOD project created efficient utilization of the ventilation air in the 153 OB, the 170 OB is currently being developed without increasing the total fresh air into the mine. This paper describes the louver system component of VOD as applied at the mine.

Jan 1, 2009

By T Goswami

The conventional practice in open cut coal strip mining has been to blast the overburden or coal layers in separate blast events. This is done in order to maximise the benefits from throw blasting and also to limit coal losses. Each blast event usually has a particular design of hole diameters, burdens and spacings, explosive charges and blast timing in order to achieve the required blast outcome for either the overburden or coal. This means that each blast has to be separately cleaned on the surface after excavation of the previous blast. Hole locations then have to be individually surveyed and marked, holes drilled, explosives and initiators loaded and the blast fired. Each of these actions takes considerable time and resources and therefore impacts on mine productivity. The mine has to be cleared for each blast event and every blast presents a new potential source for noise, dust or vibration disturbance to the neighbouring population. Exposed highwalls are also subjected to vibration and damage from each subsequent blast event

Jan 1, 2006

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

A description is given of the construction and operation of an automatic version of the coarse batch particle sizer which requires a minimum of operator supervision and which is capable of processing a sample every 4 min.

Jan 1, 1968

By Oliver Bowles

"INTRODUCTION Slate has earned a high reputation as a roofing material, carefully selected and properly placed it is rainproof, attractive, and extraordinarily durable. Despite there qualities in its favor, the slate industry during the past 30 years has suffered marked reduction in volume of sales. An increase in building construction and general improvement in business will doubtless bring renewed activity, but considerable ground has to be recovered before the industry can become prosperous. Influences tending to dwarf this long-established industry producing materials of world-wide reputation are analyzed briefly in the following pages in the hope that they may be rectified.HISTORY OF SLATE PRODUCTIONFigure 1 shows graphically the rise and fall from year to year of sales of roofing slate since 1885. In quantity, the peak was reached in 1902, and the most serious decline was from 1912 to 1918, sales at the end of this 6-year period being only one third those at the beginning. Unlike most building materials, slate experienced only a slight recovery in volume of sales during the post-war period, 1920-29. The value closely parallels the volume up to the World War period. Subsequently, however, as unit values increased the aggregate value rose sharololy above the volume curve, attaining in 1928 the point reached in 1903, although the Lumber of squares sold was scarcely one third as great. The increased unit value was due partly to larger sales of heavy architectural grades."

Nov 1, 1933

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

By Cajsa Samuelsson, Theo Lehner

Converting and refining play a central role in the extraction of metals. Sweden has a long tradition as an experimental play ground for metallurgists, chemists and alchemists, developing new methods and technologies. Presenters of papers are usually happy in recording successful developments. But reporting failures can be as great a value as the former. In the paper experiments and experience in process development are illustrated, differences between ferrous and non-ferrous developments are highlighted and industrial learning curves are discussed. 53

Jan 1, 2009

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By Joseph L. Fournier

Suncor Oil Sands employs delayed coking technology in converting bitumen into synthetic crude oil. Currently up to 10,000 m3 of delayed coke (coke) is produced per day as a byproduct of the upgrading process, of which up to 9,000 m3 per day is placed in dry storage on Lease 86/17. A review was completed to examine the case history of leachate potential experiments from the dry storage of coke and the environmental relevance of coke leachate studies conducted over the past decade. The review included an evaluation of the potential impacts of environmental conditions within the location of coke storage, including precipitation pH, as well as daily and annual ozone trends. Coke leachate potential has historically been characterized using standard leachate testing protocols (i.e., TLCP, SPLP) together with other studies that have employed strong acids and oxidizing agents in the extraction fluids. The present paper highlights prevailing conditions in the Athabasca Valley air-shed with emphasis given to ambient ozone (oxidizers), as well as precipitation pH and acid input deposition rates, and will demonstrate that TCLP / SPLP tests lack the intended environmental relevance relative to the conditions under which coke is stored.

May 1, 2011

By J. Jeffrey Wagner, Michael J. Bailey, Peter M. Douglass

The Chambers Creek Interceptor Sewer Tunnel project consisted of 2-1/2 miles (4 kilometres) of nominal 9-foot (2.7-metre) O.D. tunnel driven through predominantly glacially overridden soils. Mole-Collucio Construction Company initially elected to drive the entire tunnel with a Lovat TBM. However, this machine could not control the fast raveling ground conditions which developed when the TBM encountered sands overlying very dense, hard glacial till or boulders. As a result, a shield and digger machine was brought in for a 1700-foot (518-metre) long segment. Pumped wells spaced roughly 50 to 125 feet (15 to 38 metres) apart were utilized to dewater about two-thirds of the alignment during construction. Initial support consisted of steel ribs and wood lagging, with a final lining comprised of pre-cast concrete pipe segments grouted in place.

Jan 1, 1985

By H. Lagendijk, I. J. Reinecke

Mintek was contracted by Oriel Resources plc in 2004 to conduct a preliminary assessment study on smelting ferronickel from the large but relatively low grade Shevchenko nickel ore deposit in Kazakhstan. A detailed feasibility study (?DFS?) was awarded to Bateman BV following promising results from the preliminary assessment study (?PAS?) and small-scale pilot plant test work. As part of the DFS, a total of 450metric tons of ore was collected from three different locations in the deposit and shipped to Mintek. After sampling, the bulk sample was prepared for smelting. This comprised crushing, screening and calcining with each step done separately for the three different lots. The chemical composition of the ore from the deposit is relatively high in silica and therefore falls out of the MgO to SiO2 range that is normally processed by pyrometallurgical means to produce ferronickel. The main objective of the testwork was to demonstrate that a method could be found and successfully applied to smelt these siliceous ores and produce an acceptable nickel-containing alloy. A 2-m ID DC arc furnace was installed with a twin-cathode (electrode) configuration to replicate the proposed commercial-scale furnace and also incorporated an advanced design of water-cooled copper panels in the lower furnace sidewalls to withstand the aggressive nature of the high SiO2-containing slags. The reductant used was a high-volatile coal from Karaganda in Kazakhstan. The reductant addition was adjusted to achieve a 90% recovery of nickel. In the assessment of the process metallurgy, some deviation from equilibrium conditions was observed. This deviation is ascribed to the intermittent existence of a smelting bath partially covered with feed during the testwork. Optimization of smelting conditions should result in the metallurgy (slag metal equilibrium) being closer to the theoretical predictions and make the production of a 20% nickel alloy possible at 90% nickel recovery. The solution for the successful processing of these siliceous ores was found in the attainment of the necessary operational stability through the control of arc length, operating temperature, open-bath smelting conditions and flux additions of up to 10% dolime for the most siliceous of the three ore types. The test work carried out by Mintek provided the basis for the process flow sheet and engineering design of the DC arc smelting furnaces for the Shevchenko Nickel project.

Jan 1, 2007