Search Documents

By Juan Oswaldo Alfaro, Angel C. Nuñez, Hildebrando A. Cóndor

Se ha desarrollado un software para facilitar la evaluación del proceso molienda-clasificación en plantas concentradoras. Se ha modelado en UML-Lenguaje Unificado de Modelado; los datos e información se almacenó en SQL Server; se programó en Java (Programación Orientada a Objetos). Investigación Aplicada y Cuantitativa obteniendo como resultados un Software para Circuito de Molienda-Clasificación (Directa e Integral).

Sep 1, 2017

By Carl Belser

This report on tungsten in Ouray, San Juan, and San Miguel Counties, Colo., is one of a series describing results of studies on the tungsten potentialities in Region III, Bureau of Mines. The San Juan tungsten deposits occur in an area of 250 square miles, centering near the common corner of Ouray, San Juan, and San Miguel Counties (fig. 1). Field work supporting these studies was done in May 1954. Bureau of Mines reports prepared from investigations made during World War II and under the Defense Production Act of 1950 were reviewed.

Jan 1, 1956

By E. A. Lowe, A. F. Bellamy, J. W. Smith

"In the autumn of 1977 Bethlehem management initiated feasibility studies on recovery of by-product molybdenum from concentrate produced at the existing Highland Valley mining operation. Over the fall and winter months test work was carried forward concurrent with design, flowsheet, equipment specification and cost studies. The decision was made to go ahead with a 200 ton-per-day treatment plant. Construction started in early 1978 and progressed to an initial start-up stage in mid-June. Full operational status was reached in August 1978. Operational results through August 1979 are presented. INTRODUCTIONBethlehem Copper Corporation operates a 20,000 ton-per-day Open Pit Mine and Flotation Plant located in the Highland Valley, some 30 air miles Southwest of Kamloops and 20 miles Southeast of Ashcroft, B.C.Two open pits are worked; the Iona Pit with limited reserves of higher Mo content, and the lower grade, more extensive Jersey Pit. Upwards of 150 tons per day of bornite-chalcopyrite bulk concentrate is produced, ranging 0.25% to 1.5% in molybdenum grade depending on the area mined."

Jan 1, 1980

By K. A. Lewandowski

Binders have been suggested as an aid for agglomeration to improve copper recovery in heap leaching operations. However, it has not been established if the use of binders would negatively affect the solvent extraction process, which is used to purify the pregnant leach solution from the heaps and remove any contaminants. Such negative effects would lead to an increase in processing costs or a decreased in copper production. The controlled studies reported here have shown that some binders (a polyacrylamide and a waste treatment additive) did not interfere with the solvent extraction process. Other binders (a polyvinyl acetate emulsion and tall oil pitch) negatively impacted copper solvent extraction and, therefore, should not be used in copper heap leaching plants.

Jan 1, 2009

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a part of the 21,296-acre Million Hills Wilderness Study Area (NV-050-233) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, about 46 miles south of Mesquite, NV. The area is on the east edge of the Gold Butte mining district and has had minor production of copper and zinc from the Azure Ridge mine in the early 1900's. Assessment work was being done on the Esperanta claims, which covers the mine workings, in March 1987.

Jan 1, 1988

By S. C. A. Franca, M. T. Millqvist, A. B. Luz

Laboratory experiments were performed on a Brazilian diatomite from Bahia State to produce an industrial product for use as a filter aid. Bench and pilot plant tests were conducted consisting of: diatomite desegregation, organic matter and clay removal, filtration, drying and calcination. Calcination temperature and sodium carbonate addition influenced diatomite particle size distribution. Optimum filtration rates for calcined products were obtained at 900°C and 47 min. residence time with 3% (w/w) of sodium carbonate addition, and resultant products met specifications imposed on filter aids.

Jan 1, 2002

By Sandin E. Phillipson

The Mine Safety and Health Administration?s Roof Control Division responded to a massive ground failure at an underground marble mine in northern Georgia. The ground failure occurred in a benched area that had been abandoned in the early 1990s. It involved the failure of an estimated 19 pillars, in conjunction with a massive roof fall of an undetermined extent that was at least 60 ft high. Pillars in the benched area had been mined nominally 40 x 40 feet to a height of 50 feet ft, with 40-ft mining widths, although it seems likely from measurements and accounts from mining personnel that pillars were even smaller than intended. Average overburden depth was 500 ft, and the rock mass was characterized by three sets of intersecting geological discontinuities that not only defined very blocky conditions that were conducive to pillar spalling and volume loss, but they were also adversely oriented in such a way as to cut diagonally through pillars at a high angle. The recently released S-Pillar software from NIOSH was used to determine pillar safety factors in the failure area and indicated that pillars were undersized for the conditions. S-Pillar was used to assess pillar stability in active areas to evaluate the likelihood of experiencing similar collapses in the future. S-Pillar correctly identified the pillars in the bench area as having been at risk for instability, in light of their ultimate failure. A two-dimensional finite element model was used to evaluate the possible stages of failure and to assess the likelihood of continued failure in the benched area that might affect more distal mine openings. Although stone mines are generally characterized as having more forgiving conditions than those found in softer sedimentary rocks, the failure shares some characteristics with domino-style massive pillar collapses experienced in coal and trona mines. First, the minimum dimension of the benched area approached 350 ft; second, the pillars defined by benching had small width-to-height ratios (0.8), and; third, the pillar failure area was slightly greater than 4 acres. The massive pillar collapse and associated roof fall illustrate the importance of incorporating pillars that have been properly sized for depth and for the final bench height. Furthermore, the designed dimensions must be adhered to during the actual mining process. Finally, the importance of understanding the geological conditions and their effect on the rock mass is critical.

Jan 1, 2012

By Javier Támara

Para aumentar la productividad de la empresa minera es necesario conocer el sistema de aire -en tanto se prioriza los intereses de los clientes, y así se puede suplir todos los componentes necesarios para garantizar una máxima eficiencia y confiabilidad del sistema completo de aire comprimido que va desde el filtro de admisión hasta el punto de uso. En ese sentido, el presente texto describe las estrategias para realizar Solucionazing en ahorro energético y así aumentar la produtividad de los sistemas de aire.

Aug 25, 2002

By S. P. Singh

The purpose of the cut is to provide a free face to which the remainder of a development or breasting round can break. The results of field testing in drifts and at a quarry face were used as a basis for a description of the rock breakage and flushing mechanism in the cut. It was concluded that the important features of a cut design are proper hole spacing, sufficient relief volume, drilling accuracy and relief holes slightly longer than the planned length of the round. The void space provided by the relief holes should be about 15% of the cut volume, with more required in weak, highly fissured rocks. The importance of drilling accuracy increases with round length, an error being magnified by the small blasthole spacing. The first hole pulls only about 20% of the round length, 4-6 holes having to be fired before the cut is pulled close to its design depth. The first four blastholes should be fired with a minimum inter-hole delay of 100 ms to provide progressive relief of burden and avoid the superimposition of ground vibrations. The earliest-firing charge should be closest to the relief area and act laterally, while the first of the vertically-fired charges to be detonated should be the uppermost. Problems during cut-pulling include sympathetic detonation, dynamic pressure desensitisation, charge disruption and freezing of the cut

Dec 1, 1995

By P Rowe

New Zealand Steel's Taharoa titano-magnetite mine, south of Auckland, set two national load records when it transported around 2000 t of mining equipment three kilometres overland on time, under budget and without safety incident. It was the first time in New Zealand that four platform trailers were assembled end-to-end to transport a load. It was also the first time that a single load of 1000 t was transported on platform trailers. The need for the relocation of all equipment was realized five years ago. It took two years of planning and specialist advice to relocate the mine's 250 t dredge, 500 t surge bin, 1000 t concentrator plant and ancillary equipment from the Southern Mining Region across a specially designed haul road to the Central Mining Region. The project was carried out during a six-week shutdown in early 2001. Two dry docks were constructed, one at each end of the relocation route. The equipment was floated into a dismantling pond that was interconnected with the dry dock in the Southern Region. Through pumping, the water levels were controlled to allow transfer of the separated units from the dismantling pond into the dry dock. Once drained, sets of self-elevating platform trailers were used to transport the main units, one at a time, between the dry docks. Five prime movers were used to pull the loads. At the receiving end, the units were off-loaded in a dry dock interlinked with ,the first mining pond. The equipment was relocated because the reserves in the Southern Mining Region were mined out. A natural watercourse û the Wainui Stream û defines the northern boundary of the Southern Region and the objective became to relocate the mining plant to the other side of the stream and re-establish in the Central Region. The project team selected the trailers as the most effective means of transporting the equipment, particularly given the non-invasive means of crossing the Wainui Stream. Negotiations with prime contractor Tranzcarr Heavy Haulage Ltd commenced in mid-2000. The remainder of 2000 was spent in developing concepts with the contractor, detailed designing, preparing the dry docks, haul road and initial mine plan for the Central Region. These activities occurred with no conflict to the normal site production.

Jan 1, 2001

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in the' production of crushed stone. These studies, made at quarries scattered over the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these reports dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The present circular discusses analyses of the time Studies of the haulage systems at the same quarries. OBJECT OF STUDY The pressure of business problems frequently requires the entire atten¬tion of quarry management and in consequence internal plant economies often are neglected, Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that similar studies of many plants by impartial engineers would disclose possibilities for cost reduction or greater efficiency in internal plant processes.

Jan 1, 1939

By Shahid Islam, Lucian Bogdan

Deep and large diameter drilled shafts use mostly bundles of Grade 60 (415 MPa) reinforcing bars as longitudinal reinforcement with rebar splices to make it longer. Lower Grade steel requires large number of bars which result in rebar congestion and difficulty in placing concrete. This leads to increased labor cost for fabrication and installation. By utilizing larger size and higher strength threadbar, the congestion of rebar can be reduced significantly and bundling of bars can be avoided. The lap splices are replaced with simple threaded couplers and end hooks are replaced with end terminators. Threadbar conforms to ASTM A615-15 and can be epoxy coated if required for corrosion protection. This paper describes an attractive value engineering of replacing Grade 60 (415 MPa) bundle of rebars with larger diameter Grade 75 (515 MPa), Grade 80 (550 MPa) and Grade 100 (690 MPa) threaded bars and threaded couplers in some specific drilled shaft projects in the USA. INTRODUCTION A drilled shaft which may also be referred to as drilled piers, caissons, cast-in-drilled-hole piles and bored piles is the key element to the foundation of massive structure. They are used for tall buildings, bridges and foundations for other applications such as retaining walls, sound walls, signs, or high mast lighting. Drilled shaft foundations are typically 3 to 12 feet (0.9m to 3.7m) in diameter cast-in-place deep foundation elements constructed in a drilled hole that is stabilized to allow controlled placement of reinforcing steel and concrete. Drilled shafts for transportation structures are commonly used to depths of up to 200 ft (61m) in the USA. Drilled shafts can be installed in a variety of soil and rock profiles, and are most efficiently utilized where a strong bearing layer is present. The reinforcing cage is typically lowered into position within the hole and then concrete placed through the center of the shaft, flowing from bottom to top through the reinforcement to fill the hole.

Jan 1, 2018

By S Henderson

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Microprobe analyses.of sphalerite grains from the Waitangi deposit mostly range from 0.8 to 1.5 mole % FeS, although one sample contains 9.5 mole % FeS. Arsenopyrite from Waitangi yields a range from 33.1 to 34.6 atomic As (%). There is no discernible correlation between the FeS content of sphalerite and gold grade in the Waitangi deposit suggesting that gold deposition is probably not controlled by changes in temperature and activity of sulphur aS2 that control the FeS content of sphalerite. The possible causes for gold deposition are thought to be boiling, mixing and changes in pH. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-ehalcopyrite samples yield a narrow range of d34SCDT values (-1.0 to 0.9 ë;n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source. However, the source of light sulphur in the late pyrite grains is not known. Preliminary fluid inclusion+studies indicate homogenisation temperatures between 173¦ and 284¦C and salinities of 0.23.0 NaCI equiv. wt % (uncorrected for C02). Vein quartz at Waitangi yields d18OSMOW values from 6.8 to 12.7 ë (n=23). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1-5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in d18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that d18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1993

By Doss H. White

The value of non fuel mineral production in Alabama in 1991 was $539.9 million, a decrease of $20.7 million, a result of the nationwide recession that was felt throughout the State's economy. The 3.7% decline in mineral sales was due primarily to a slowdown in construction, which had a major impact in the construction minerals mined instate. Production and sales of crushed stone and sand and gravel fell significantly below the value reported in 1990. Despite the recession, Alabama moved from 21st to 20th place nationally in mineral value. Mineral industry developments in 1991 were primarily in the metals manufacturing sector. Reynolds Metals Co., Sheffield, celebrated 50 years of operation in Alabama. During the November celebration, the company dedicated a $121 million expansion that included a new casting facility and sheet rolling operation. Gulf States Steel Corp., Gadsden, completed the first full year of operation of its new multimillion-dollar continuous caster.3 The Foundry of the Shoals Inc., Florence, replaced two coke-fired furnaces with electric furnaces.

Jan 1, 1993

The Bureau of Mines is operated to assist in promoting economic development through increased efficiency in the mining, preparation, treatment, and utilization of mineral substances; to aid in conserving mineral resources through preventing waste; and to help the mining industry improve health conditions and increase safety. Accomplishment of those ends is sought through investigation of scientific, technologic, and economic problems of the, mineral industries and dissemination of resulting information. Building materials of mineral origin constitute an important product of mining, and the Bureau makes studies of these in the various fields mentioned. The following commodities come within this classification: Asbestos, anhydrite, asphalt, cement, clay and clay products, diatomite, dolomite, glass and mineral wool, granite, greenstone, gypsum, lightweight building materials, lime, limestone, magnesite, marble, sand, sand and gravel, sandstone, sand-lime brick, slate, soapstone, and trap rock.

Jan 1, 1937

By Edward A. Barrett

The ability to recognize visual cues commonly associated with roof and rib hazards is fundamental to the prevention of groundfall accidents. The perceptual skills that miners possess to visually search and assess hazardous ground conditions differ considerably. This U.S. Bureau of Mines report summarizes recent investigations on the use of stereoscopic (3-D) slides as a training aid for improving the ability of miners to recognize the various geologic and mining-induced irregularities that cause ground-falls. The feasibility of using 3-D slides for training and their effectiveness for representing roof and rib hazard conditions are discussed. Information is presented on equipment and procedures for creating a 3-D slide program that can be updated by mine trainers. Recommendations are made on selection of 3-D equipment and on the use of 3-D slides for training miners to recognize roof and rib hazards.

Jan 1, 1988

By I. J. Brown

Paper prepared for presentation at Industrial minerals and the environment, held in Leeds, 24-35 September 1990. The need to submit an environmental statement (EIS) has certainly increased the workload of those concerned with both its production and assessment. However, there is now good evidence that the system is enhancing public confidence in the minerals industry in particular and improving relationships between the developer, planning authority and those consulted such as statutory bodies, parish councils, civic societies, nature conservation interests and ramblers

Jan 1, 1991

By B. O. Odera

The Pt-based alloys have a high potential for replacing some Ni-based superalloys (NBSAs) used in the highest temperature and most aggressive environments, and vanadium would be a beneficial alloying element. Six alloys of average compositions Pt-26.6Al-9.1V, Pt-23.1Al-17.8V,Pt-9.6Al-21.1V, Pt-17.4Al-6.4V, Pt-22.3Al-7.9V, and Pt-6.0Al-10.1V (all in at.%) were manufactured by arc-melting and examined in the as-cast condition using scanning electron microscopy and X-ray diffraction (XRD). Five samples were heat treated at 1 000°C for 1 500 hours and water quenched, then examined. The phases were identified using energy-dispersive X-ray spectroscopy and the identities were confirmed by XRD. In most of the samples, the phases existing in the as-cast condition were different from those at 1 000°C after ~1500 hours heat treatment. A solidification projection, an isothermal section and a liquidus surface projection were determined for the Pt-rich corner.

Jan 1, 2012

The rapid advance in the adaptation of scientific knowledge to the treatment of ores, resulting in improved chemical and metallurgical processes, has enormously increased the possibility of working lodes profitably, which a few years ago were passed over as unpayable. By the discovery of chlorination, and later of "Cyanidation," by the highly improved methods of concentration, and by the rapid advance in our knowledge of smelting (for which we are greatly indebted to Americanmetallurgists), and by the gradual replacement of scientifing principles and enlightened management, for rule-of-thumb methods formerly in vogue, many large low grade bodies have been opened, and are now paying dividends, which were,twenty years ago, looked upon as hopelessly unpayable. It has been more especially in these large low grade ore bodies, that modern methods have been benefical; for small lodes must be rich to pay at all, as they cannot be worked on the same gigantic scale, but even in these a percentage of metal is saved which formerly was absolutely lost.To make these large deposits remunerative it is, however necessary to try and find the point of greatest economic advantage, to handle the ore in vast quantities, to erect huge plats to treat it, to substitute automatic appliances for hand labour as far as possible, and to combine several processes supplementary to one another, so that ore which is not amenable to one process, shall be saved, by another; and by doing...

Jan 1, 1901

By G. Miller

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixers. Recent experience with both large and small plants has shown that this is not the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers. Both of these lead to either reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Further, changes to the method of specification and selection of both primary and secondary mixers have been made to eliminate the onset of partial separation during operation. Observation of settler operation has shown that it is also a dynamic process, even under ‘steady state’ conditions. Four different transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze, and erratic and high entrainment levels in the discharges. A first approximation analysis has shown that there are significant pressure differentials within settlers and these change along the length and with phase separation rates. A technique to control the effects of these transients has been developed which allows plant performance to be improved beyond ‘standard’ expectations. The design and selection of the settler internals is described.

Jan 1, 2001