Search Documents

By M. Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

Jan 1, 2005

By R. Mckinstry, M. Rantapaa, T. Bolles

"Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore.Barrick Goldstrike’s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs."

Jan 1, 2005

By K. Wongaew, R. F. Cook, J. E. Carlson, T. Cleys, C. R. Smith

Steel fiber reinforced concrete segmental rings are the final tunnel lining for approximately 85% of the alignment for a 6.706-meter (22-foot) internal diameter tunnel being built as part of the East Side Combined Sewer Overflow Tunnel Project. This paper describes the approach adopted for the design of the steel fiber reinforced concrete segments, the development of the performance criteria for the segments, and the testing program used to confirm the performance of the materials and segments in the laboratory and in the field.

Jan 1, 2007

By Donald H. McLaughlin

ALTHOUGH Cerro de Pasco was well known since the early sixteen hundreds as one of the major silver districts of the Andes, its development on a modern scale did not occur until the first decade of the present century when a syndicate organized by James B. Haggin initiated the enterprise that eventually grew into the complex and widespread operations of the Cerro de Pasco Copper Corporation. Options on a few claims in Cerro de Pasco that had been brought to New York in 1900 came to the attention of A. W. McCune, a mining man from Salt Lake City, who took them to Haggin and soon succeeded in interesting that creative mining financier in the possibilities of the district. James MacFarlane, an engineer well known to both Haggin and McCune, was sent to Peru early in 1901 to make the initial examinations which promptly led to acquisition of a substantial group of claims in the heart of the mineralized area. A syndicate to which Haggin turned over his rights was organized on Feb. 26, 1902 to provide the necessary funds. The original members were J. B. Haggin, who retained a 34 per cent interest, Edward H. Clark (for Mrs. Phoebe Hearst, the widow of Haggin's old associate, George Hearst), H. McK. Twombly, H. C. Frick, D. O. Mills, and J.P. Morgan.

Jan 1, 1945

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

Sluiceboxes can provide a much higher concentration ratio than most other gravity concentrators (up to 50 000:1) at very high overall placer gold recoveries (greater than 99 per cent). They are also very reliable, inexpensive and simple to operate. This combination is very difficult to beat and explains why the sluicebox is still the most important placer gold concentrator in northwestern Canada, Alaska and the rest of the world. A sluicebox is a rectangular fl ume containing riffles on matting, through which a dilute (<12 per cent) slurry of water and alluvial gravel flows. Sluiceboxes are actually centrifugal concentrators with settling velocity playing a minor role in gold recovery. Due to their higher density, gold particles tend to segregate to the bottom of the slurry flow where they form a streamline that is diverted by a low pressure zone into a riffle. Under ideal conditions, this ribbon of slurry will be overturned as it flows down the rear of the following riffle and will continue fl owing in a circular path to form a vortex. At the bottom of this vortex, centrifugal and gravitational forces combine to drive gold particles into or beside the matting. To remove the gold concentrates, sluiceboxes are shut down and the riffles and matting are taken apart and cleaned. The slurry velocity provides the energy that powers the vortex. If the velocity of the slurry is reduced through overloading with solids, insufficient water flows or shallow gradients it may not sustain a full size vortex. If the riffles are too close, too far apart, too tall, or if there is not enough energy available to the vortex, the vortex will not be formed properly and gold recovery will be reduced. If the slurry velocity is too high, extreme turbulence and the resulting scouring will also cause gold losses. Testing sluiceboxes with conventional sampling and evaluation techniques is very costly, time consuming and problematic. Most placer gold ores contain a very small number of gold particles in a large volume of pay gravels. Sluiceboxes can lose coarse gold particles. The presence or absence of one of these particles in a tailings sample can lead to high unpredictable errors (nugget effect) even when large sample volumes are processed with care. Every time conventional samples are upgraded, additional errors are introduced due to the inefficiency of recovery equipment. Nuclear tracer tests are more accurate, faster, cheaper and safer than conventional sampling. In 1989 through 2002, the recovery efficiency of dozens of sluicing systems was determined by mixing radioactive gold particles (tracers) into the feed streams of dozens of placer mines in the Yukon Territory, British Columbia, Alaska and Guyana. Four distinct sizes of nuclear tracers were used and their recovery was related to the design and operational characteristics of the individual sluiceboxes and their pay gravels. At clean up, scintillometers were used to detect the very low level X-ray and gamma ray radiation emitted by these tracers and locate them in the sluice runs. The effectiveness of any given section of riffles was easily diagnosed by the presence or absence of tracers. At every mine the gravel feed rates, water flows, equipment dimensions and riffle performance were measured. After the gold tracers were removed from the fi nal concentrate and counted, the concentrate was sieved and weighed. These gold recovery, weight and sieve data were used to calculate the quantities and size distributions of the gold particles in the original pay gravels and those lost in the tailings. The expired tracers were stored in a lead lined container until their radioactivity was near background levels (about two months). The standard errors from these radiotracer tests were estimated from binomial probability theory with the equation: SE = {(n + p + q) ^ 0.5}/n. Where n was the total number of radiotracers added, p is the proportion recovered and q was the proportion lost. Each overall recovery estimate would be within one standard error of the true recovery value (14 times out of 20) and almost always within two standard errors of the true recovery (19 times out of 20). The maximum standard error with 100 tracers was five per cent and occurred when the recovery approached 50 per cent. With higher recoveries, standard errors usually ranged from one to two per cent.

Aug 1, 2010

By C. Alexander

Stillwater Mining Company is developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in south central Montana. A 5650 meter (18,550-foot) tunnel is required to gain access to the ore bearing horizon (J-M Reef). Access and primary mine development can be accelerated through the use of two 4.6 meter (15-foot) diameter tunnel boring machines (TBM). One TBM was purchased new while the other was purchased used. Machine specifications, site support facilities, portal/launch chamber construction, TBM assembly, startup and operation are discussed in this paper.

Jan 1, 1999

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong Operational Readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.The road blocks encountered are often from systems that one assumes will operate without trouble such as air-conditioning, or design assumptions that were taken years earlier in feasibility process stages, namely the capacity of existing systems that will connect the new plant to the existing facilities. The challenges associated with rectifying these issues in addition to the requirements to properly start-up and operate a new plant without impacting production are great, and it is imperative to have the necessary resources to react quickly to any problems.IntroductionCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary by-product of the process."

Jan 1, 2016

By Mark I. Copeland

The Bureau of Mines investigated the effect of up to 1 wt-pct of copper and silicon on the heat treatment response and hardness, tensile, and impact properties of hot-rolled medium-carbon steels. The steels were prepared by induction melting and fabricated into plates by forging and rolling. The tensile strength of 0.2-wt-pct carbon steels containing 0.3 wt-pct silicon was affected significantly by copper in both the hot-rolled and heat-treated (600° C) conditions, whereas the tensile strength of the 0.3-wt-pct carbon steels was less affected. A 600° C treatment was considered optimum as a post-rolling treatment to strengthen the steels by copper precipitation. Strengthening of 0.2-wt-pct carbon steels by silicon was reduced by increasing copper contents.. Optimum impact strengths occurred at about 0.3 wt-pct silicon in 0.2-wt-pct carbon steels containing 0.6 and 0.8 wt-pct copper. The impact strengths were lowest for 0.2-wt-pct carbon steels containing over 0.8 wt-pct copper and greater than 0.3 wt-pct silicon, especially in the heat-treated condition. Copper and silicon solutes and copper precipitates strengthened the steels. This effect was augmented slightly by strengthening through grain refinement by these solutes.

Jan 1, 1973

By Yajie Wang

Traditionally, roof falls are usually attributed to bad roof strata and high vertical stress related to the overburden depth. However, roof falls under shallow overburden depth are oflen caused by a high horizontal stress field. Recent studies have proven that the high horizontal stress field, if existing, plays a major role in roof stability. Also the roof conditions are related to the entry diredions under a horizontal stress field. Questions are: How to orient the entry to a favorable direction to prevent the roof falls? If the entry cannot be oriented, how to support it? Through a case study in mine A, this paper analyzes the horizontal stress effect on roof stability. The guideline for the entry orientation is given based on the results of analysis. Additionally, suggestions are made for those entries that cannot be oriented to a favorable direction.

Jan 1, 1998

By Ralph Harris, Qi Xia

"Gold cyanidation rates are known to be limited by the rate of oxygen dissolution in the cyanidation tanks. The effect of solids loading on the oxygen dissolution rates is not obvious and the results of previous studies are ambiguous. The present paper presents an analysis of oxygen dissolution rates using a ""spent"" commercial gold slurry diluted to various levels of solids loading. It was found, in an 170 litre stirred tank reactor using an inverted cone sparger, that under certain high loading conditions, there was a decrease of as much as 50 %, i.e., there was a halving of the rate of oxygen dissolution as compared to that in clean water. In particular, it was observed that, due to gas flooding of the impeller, there was a drop in kLa even with an increase of gas velocity. Gas holdup reached a maximum value of only 1.7 %. The total power consumption was between 0.06- 0 .10 kw/m3 within the range of gas velocity before flooding occurred. The decrease in oxygen dissolution rate with increased solids loadings is believed to be mainly due to the increase in the apparent viscosity which reduced the turbulence and shearing effect and resulted in larger bubbles and hence reduced the reaction area a. The interrelations between solids loading, gas holdup, flow pattern, power consumption, and liquid mass transfer coefficient are discussed.IntroductionThe reactors generally used in gold cyanidation are Stirred Tank Reactors (STR). Compared with other types of reactors like fluidized bed reactor and column reactor, STR is of particular importance due to its wide application in industry. It is reported that the stirred tank reactor is used for more than 50 % of the world's chemical production (Xu and McGrath, 1996)."

Jan 1, 1997

By Du Sichen, K. Mukai, S. Seetharaman

Viscosities of slags constitute an important physical property needed for an understanding of the mass transfer phenomena in metallurgical processes. Viscosity is also the key that leads to a better understanding of the structure of slags. It is well known that the viscosities of silicate slags decrease with the addition of basic oxides due to the breaking of the silicate network. The measurements of slag viscosities often pose experimental challenges, especially to the choice of materials. The keynote lecture takes up the experimental problems and the various techniques adopted. Dynamic viscosity measurement, as a powerful tool towards an understanding of the kinetics of some high temperature reactions, is brought out. A number of semi-empirical models have been developed to estimate the slag viscosities in the case of multi component slags. A critical survey of these models is presented in the lecture. Earlier models by Riboud et al., Urbain et al. and Mills et al. have been developed further into a new generation of models. Some of the current important models are (1) Model by Iida et al. (2)CSIRO model (3) Pyro research Model (4) Model by Tanaka et al. (5) Model approach by Reddy et al. and (6) KTH-model. The predictions and capabilities of the various models are compared. Estimations of viscosities from thermodynamic data and prediction of liquidus temperatures from viscosities are presented. The concept of surface viscosities with reference to slags and viscosities of two-phase mixtures are also taken up in the presentation.

Jan 1, 2004

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977

By Clarke E. Schuetze

This project had as its objective the experimental investigation of water capsule production utilizing the Southwest Research Institute's submerged nozzle encapsulation apparatus (U.S. Patent 3,389,194). Initial efforts on this project involved nozzle configuration and shell formulation optimization. The shell formulation developed on a prior program was modified during the course of the project to obtain the best balance of capsule breakage resistance and water retention. Subsequent effort centered on determining operating conditions which would produce the best quality capsules for each candidate shell formulation as determined by laboratory tests. Some preliminary work was done to increase the production capacity of the encapsulation equipment. The program was extended with major emphasis concerned with scale-up studies of capsule production capacity and the treatment of problems associated with grouting cartridge fabrication. During the course of the program, water-containing capsules were produced which have good long-term water retention, block resistance and adequate strength. Using a single-nozzle design, a production capacity of 15.9kg (35 pounds) per hour was demonstrated to give acceptable capsules based on initial results.

Jan 1, 1978

By H. Yilmaz

Tensile strength testing has been one of the most common physical property testing methods of thin spray-on liner (TSL) products worldwide. However, the variety of products tested has been insufficient for comparison purposes. Specimen preparation procedures and test parameters such as curing time and loading rate are not reported well. Comprehensive tensile strength testing on 20TSL products and one plain shotcrete brand was performed over 28days of curing period. Detailed information on the test procedures with particular attention on the important aspects during sample preparation and test execution are provided. As expected, the tensile strength increases with increasing curing period. The test results make the categorization and comparison of liner products possible.

Jan 1, 2010

By J. L. Konchesky

The technical feasibility of gasifying powdered, noncoking, low-rank coal with steam in an externally heated tube has been demonstrated. The tube, 112 ft. of alloy-steel tubing shaped into a helix, served as an electrical conductor of electricity used for heating. The effects of the following variables were studied: Residence time of coal in reactor, average reaction temperature, steam concentration, and rank or geologic age of coal. Reaction pressure was maintained in the range 19-26 p.s.i.a. High carbon conversions and large yields of synthesis gas were obtained with low-rank coal. In one test, for example, about 88 pct. of the carbon in a subbituminous C coal was gasified at 1,910* F. with a residence time of 1 sec. The gas contained 58 pct. H2, 19 COD 15 CO, and 3 CH4; the yield was 30 cu. ft. (at 32' F. and 14.7 p.s.i.) of synthesis gas (CO + H2) per pound of dry coal.

Jan 1, 1960

By Pietro Navarra

A great deal of effort has been expended on how to optimize conventional water cooling circuits in furnace cooling elements, and the results have been largely satisfactory. However, there is a general agreement that the proximity of high-pressure water passages to the flow of molten furnace products is a safety concern. Nonetheless there exists little alternative to the formula: increasing furnace integrity implies the incorporation of more extensive forced-convection water cooling systems. Recent developments in evaporative cooling technology have resulted in the development of a high-capacity heat pipe capable of operating under the thermally intense environments of a metallurgical furnace. The system functions using several kg of a working fluid (water) in total, has no moving parts, and allows for a significant reduction in cooling water requirements. Full-scale pilot tests of a copper tap hole and slag launder were done in 2003 and2005, with detailed results given in this paper.

Jan 1, 2006

By V. Rajagopal

Corrosion and abrasion properties of a series of chromium-containing cast iron balls with Cr contents ranging from 0 to 29% was evaluated and compared with austenitic stainless steel and mild steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite with either 5% pyrrhotite or 5% chalcopyrite under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynamic polarization curves under abrasion. An offset in their electrochemical activities was observed somewhere between 16 and 26% Cr. In fact, 26 and 29% Cr cast irons showed an excellent corrosion resistance approaching that of austenitic stainless steel. Flotation recoveries were estimated on a 95% quartzite + 5% pyrrhotite sample ground with various cast iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with corrosive wear obtained from marked ball wear test and with flotation results.

Jan 1, 1991

The commercial application of electrolysis to zinc sulphate solutions for the production of metallic zinc is a development ·of the past twenty years. Earlier attempts failed to give satisfactory results, chiefly because certain harmful elements were either not recognised as being present in the solution, or, if recognised, suitable methods of removal had not been developed. The electrodeposition of zinc from zinc sulphate solution is extremely sensitive to the influence of a great many factors, all of which appear to be closely inter-related.Some of these factors tend to minimise the necessity for a high degree of purity of the solution, while other factors aggravate the harmful nature of certain impurities.The relationship existing betweBn the various factors in zinc electrolysis makes a general discussion of the injurious effect of impurities very difficult since, under one set of conditions a given concentration of an impurity may be of minor: importance, where its under another set of conditions the same concentration of that impurity may prove dangerous to successful electrolysis.

Jan 1, 1934

By A. C. Legg, M. T. Malema

Keywords: Pyrometallurgy, flash, smelting, furnace, nickel, copper, Botswana BCL Limited operates the only Flash Smelting Furnace on the African continent, at Selebi-Phikwe, situated in north-eastern Botswana. The furnace was commissioned in 1973 and produces a high-grade sulphide matte containing nickel, copper and cobalt, which is shipped to refineries in Zimbabwe and Norway for further processing. This paper outlines the recent process improvements and plant expansions that have resulted in a capacity increase from 40 000 to 60 000 tons per annum of metal production.

Jan 1, 2006