Search Documents

By Gorr W. W., Wyche E. H, R. Smith

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Gorr W. W., R. Smith, Wyche E. H

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Huilan Yang, Feng He

This paper intends to introduce the development of copper smelting and converting technologies in China in recent years, with a particular emphasis on the introduction of various continuous converting technologies, and moreover, it analyzes the advantages and disadvantages of those technologies, including their impact on the downstream anode refining from different points of view. INTRODUCTION At present, many converting technologies are used in copper pyro-metallurgical plants in China, including Peirce-Smith (PS) converter, flash converting furnace, multi-lance based top blowing, bottom blowing and so on. These technologies have spanned a wide range of time. PS converter technology has been applied in copper smelters for many years and most of the blister copper have been produced by this technology; flash converting technology has been developed since 1990s and been maturely applied in several plants up until now; top blowing and bottom blowing technologies have been revived in China in the past decade and boast good environmental protection performance, energy efficiency, throughput capacity and short process flow. All of the said technologies have reference operations in treating high-grade matte. As more and more attention is paid to environmental protection globally and copper smelters continuously seek for cost reduction, it is necessary to share those converting technologies, especially those new converting technologies derived in China, with copper smelting practitioners in the world. This paper aims to analyze the advantages and disadvantages of various technologies from a macroscopic view and discuss their actual application effects, current developments and future improvements. BRIEF INTRODUCTION OF VARIOUS CONVERTING TECHNOLOGIES IN CHINA China has seen a rapid development in copper smelting industry in the past 30 years and has become the largest gathering place of copper smelters in the world, most of which are operating with PS converting furnace technology, however, with the increasingly strict environmental requirements of the Chinese government in recent years, the low-level pollution issue and the disadvantage of large gas exhaust amount per unit of copper of converting furnaces are particularly prominent.

Jan 1, 2019

By M J. Kongas, K M. Saloheimo

This paper presents the art of on-stream particle size and elemental analysis used at iron ore concentrators, followed by the results and experiences from several sites.Online particle size analysis is rather common at medium- to large-sized concentrators. Online X-ray fluorescence (XRF) elemental analysis, however, is only used in some iron ore concentrators, while it is a routine practice in base metal concentrator plants. Online XRF analysis is applicable for process monitoring and control down to four to five per cent silica by measuring Fe assays accurately. With lower silica content, direct measurement of silica and other light elements is required. Some light element analysers that are based on the prompt gamma neutron activation analysis (PGNAA) method have been developed, but they have not performed up to expectations with slurry analysis. Other methods have been tried though these have not been used beyond prototype installations. Operating online light element slurry analyser installations are not common in iron ore applications.There is an economic incentive to mine lower and variable grade iron ore resources, which require concentration and removal of several impurities to produce high-quality concentrates for pellet production. Monitoring such operations by on-stream analysis has significant economic benefits, and there is a need to develop a dependable slurry online analyser for Si, Al, Mg and other light elements. The latest developments in slurry on-stream light element analysis are described.CITATION:Kongas, M J and Saloheimo, K M, 2013. Online slurry analysis for process control and monitoring at iron ore concentrators, in Proceedings Iron Ore 2013 , pp 303-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

This report covers the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. Significant conclusions that will be of benefit to the entire mining industry are the following: It appears from the study that the productivity of the slushing equipment itself cannot be substantially increased using the existing technology; the unsafe situations associated with slushers can be improved by better anchoring practices, by providing better work station layout that incorporates improved clearances and protected walkways over the ore pocket, by lighting the slusher drift, and by improved operator training; improved technology needs to be applied to the movement of broken ore in the stopes; and slushers will continue to be used in the mining industry in certain spedial and unique situations outlined in the report.

Jan 1, 1974

By J. P. Germiquet

"Rock properties have a material impact on mining processes, including drilling performance. An investigation using point loaded index (PLI) data converted to uniaxial compressive strength (UCS) has revealed that a direct relationship between grain size and UCS exists at Mogalakwena Mine. This correlation is best seen in unaltered rock, with lower correlations for altered rock types. Measurements from the new RockMa system installed on drill rigs can be used to obtain rock strength data to validate the current rock strength domains and create additional data for the next benches below. An investigation of penetration rates in different lithologies shows that rock composition plays an important role in determining drill performance. Additionally, there is an inverse relationship between rock strength and drilling penetration rate – a measure of how efficiently a hole is drilled.The domaining of grain-size-adjusted UCS at Mogalakwena Mine will allow more accurate scheduling of drill rigs through increased knowledge of rock strength in various areas. Successful rock strength domaining has the potential to be incorporated into blast indexing and predicting crushing/milling performance.IntroductionThe optimization of mining and processing through geometallurgical characterization of ore are key drivers of value realization (Deutch, 2013). Rock strength is one such property and is affected by, among other variables, composition, texture, and grain size (Ozturk, Nasuf, and Kahraman, 2014). Mogalakwena Mine is exploiting the intrusive Platreef PGE (platinum group element)-bearing orebody which forms part of the northern limb of the Bushveld Complex. This complex orebody exhibits areas of metasomatic alteration, metamorphism, and sporadic mineralization of the footwall and hangingwall (Nex et al., 2006). Understanding this variability is paramount due to the implications for rock strength and hardness, which in turn affect crushing, milling, and liberation efficiency. These variables must be known prior to blasting in order to optimize mine and plant processes using in-situ variables. This necessitates predictive modelling (Deutch, 2013). Geological and geotechnical data was sourced from the Overysel (OY) exploration database for the study. Point load testing was done for each borehole and the results converted to uniaxial compressive strength (UCS) (Akram and Bakar, 2007). The relationship of lithology, texture, and grain size with UCS revealed an inverse relationship between grain size and UCS in unaltered rock. The relationship was not present in altered rock types. A comparison of mean strength and hardness results indicated that Bond work index and UCS may be related. Drilling performance is affected by UCS (Bourgoyne et al., 1986), and this was proven using recent measurements obtained during drilling. Lastly, grain-sizeadjusted UCS values were applied to a 3D model for the OY property."

Jan 1, 2016

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By Segnit E. R

Results are reported of a study of the reactions occurringin the combustion of chaIcopyrite particles underconditions simulating those in the shaft of a flashsmelter.The reactions were studied using kinetic and mineralogicaltechniques. Reactions. rates above 500°C wererapid, most of the reaction taking place in less than 50ms. Final products were copper-iron ferrites with spineltype structures. Probable reaction mechanisms are discussed.

Jan 1, 1977

By Carl L. Bieniewski

In a Bureau of Mines supply evaluation, the known uranium resources in the United States are estimated to have a total recoverable uranium oxide (U3O8) content of 3,132,400 tons at prices up to $69.32 per pound. Only those resources were evaluated for which sufficient quantity data are available and process technology exists for recovering uranium. A total of 160,800 tons of U3O8 is available at $8 per pound from ore deposits presently mined and an additional 244,700 tons available at prices up to $30 per pound from similar but usually lower grade deposits. A total of 2,726,900 tons of U3O8 is available from four other resources: copper leach solutions, wet-process phosphoric acid, Florida phosphate rock Leached zone, and Chattanooga Shale. These resources contain from 30,000 tons of recoverable U30, at a price of $7.52 per pound as a byproduct of copper leach solutions to 2,557,300 tons at a price of $69.32 per pound from Chattanooga Shale.

Jan 1, 1971

By Andrzej Walentek

This paper presents the results of numerical modeling of the fractured zone around longwall gateroads. The numerical computations have been based on the results of underground measurements of the fractured zone around longwall gateroads, which were performed for various geological and mining conditions and measured with the use of the endoscopic method with a digital camera. Having results of the underground investigations, trials of duplicating them by the Finite Element Method using software PHASE and the Hoek-Brown failure criterion were performed. In order that the fractured zone predicted by the model-based computations closely simulate that measured underground, some selected parameters in the Hoek-Brown failure criterion were modified based on the earlier determined relations used for prediction of the roof-to-floor convergence in longwall gateroads. As a result, the model-based computations produce results very close to those obtained from the underground measurements. Determination of the fractured-rock zone around the mine roads is of great importance to mining practice, especially in planning and designing supports for longwall gateroads. The influence of the front abutment pressure causes the fractured rock zone around the roads to increase and results in an increase of support load. Moreover, proper determination of the fractured rock zone is one of basic elements in the process of planning roof bolting for mine workings.

Jan 1, 2009

Physical/Chemical Treatment of Mercury-Contaminated Wastes from Former Chlorine-Alkali Electrolysis Plants - Application of Flotation Technologies in Soil Washing Plants

Sep 13, 2010

By Llewellyn A. Rubin

ROUTINES AND SUBROUTINES A- 1 Wait Loop (Wait) A- 2 Receiver Processing (RCVP) A- 3 Control Panel Sequence (CPNL) A-4 Interrupt Routine (INTRP) A- 5 Math Processing Routine (PROC) A-6 Input Constants for Math Routine (CONI) A-7 Angle Conversion Routines (LVERT) A- 8 Display Routine (DSPY) A- 9 Message Print Auxillary Routine (MESSO) A-10 Auxillary Subroutines (AFUTC and AGETC)

Jan 1, 1973

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

By Flavio Begazo Mamani

Recientemente Southern Perú desarrolló un nuevo proyecto donde se modernizaba la planta de Fundicion y se reemplazaba el convencional horno reverbero por la tecnología del ISASMELT, capturando más del 92% de los gases generados durante el proceso de fusión de los concentrados de cobre. En ese sentido, el presente texto describo los efectos de la modernización de la Fundición sobre la calidad anódica. Antes de la modernización de la Fundición, los ánodos fueron producidos en la planta de ánodos ubicada en la Refinería de Cobre de Ilo. Ahora los ánodos son producidos directamente en la Fundición y como resultado, la composición química de los ánodos ha cambiado, principalmente en el contenido de bismuto, antimonio, plomo y zinc, siendo diferentes a los parámetros de diseño original de la Refinería. Asimismo, este factor impulsó a revisar el proceso de remoción de impurezas y los parámetros de la refinación electrolítica en la Refinería para evitar la contaminación del cobre refinado, logrando mantener la continuidad de la producción de cátodos de cobre de alta calidad superando los estándares interna-cionales de la norma ASTM-B115.

Sep 12, 2011

By Laurens de Jonge, Wiebe Boomsma, Rodney Norman, Stanislav Verichev

"Earth provides natural resources, such as fossil fuels and minerals that are vital for human life. As the global demand grows, especially for strategic minerals, commodity prices rapidly rise. Thus there is an identifiable risk of increasing supply shortage for minerals. Hence a major element in a long-term economic strategy must be, to ensure security of supply for these strategic minerals. In this rapidly changing global economic landscape, deep sea mining has gone from a distant possibility to a likely reality within just a decade.Although deep sea minerals extraction was investigated in the 1970’s, it was abandoned because of changing commodity economics, advances in on-land exploration techniques, growing concern on environmental impact, and political and legal aspects with regard to ownership issues. The developmental data from those days, if still available, are not adequate to allow engineering and building of an integral system for extraction of deep sea minerals without additional R&D work. Thus, deep sea mining is yet to attain a Technology Readiness Level (TRL) sufficient to successfully undertake deep sea mining operations, from resource discovery to resource assessment and to resource exploitation [Blue Mining, 2014]."

Sep 1, 2014

Although bismuth mineralization is spread widely through the Lachlan Fold Belt in New South Wales, broad grouping of the various deposits can be effected on the basis of geographical and geological (age and type of associated rocks) affinities. As a result, significant concentrations of bismuth can be recognized in the Mid-Western granites, Cobar-type ore, the Yass Silurian acid volcanic belt, and the Albury, Bega, Braidwoodand Bathurst districts.In these deposits bismuth generally occurs in minor amounts associated with molybdenite, wolframite, scheelite, cassiterite, chalcopyrite, galena, magnetite, pyrite, arsenopyrite, and native gold. From this group of minerals three broadly defined associations can be recognized.I. Bi-Sn-W-Mo2. Bi-Au( -Te)3. Bi-Pb-Cu(-Au)There may be some interchangeability of these metals, as instanced by occasional Bi-Cu-W-Mo mirleralization, but pyrite and/ or arsenopyrite are usually prominent in all associations.The first two of these associations occur mainly in the form of narrow quartz veins rarely averaging more than O· 3 per cent Bi, although there is often a marked enrichment in ferruginous material in the oxidized zone.Most of these veins occur within or adjacent to granitic rocks of varying ages (principally Silurian or Devonian), although Bi-Au mineralization tends to be related to more basic igneous activity than the Bi-Sn-W-Mo association.The latter is also occasionally developed in pipes, usually coarse-grained and richer in bismuth (as at Whipstick, the principal mine in New South Wales with a production of 343 tonnes of the metal), or in lower grade, but probably larger tonnage skarn deposits. The bismuth-base metal association occurs mainly in Silurian acid volcanic sequences and may also form low grade but large tonnage deposits, such as is possibly developed at Cobar.

Jan 1, 1973

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987

By D. F. Malan

This paper presents an overview of work conducted over several years to investigate the continuous stope closure profiles recorded in tabular excavations and the use of this data as a hazard indicator. In spite of the brittle nature of the rock, measurements in gold mines and intermediate depth platinum mines revealed a significant time-dependent closure component. Various approaches to simulate the time-dependent closure have been investigated. Viscoelastic theory is able to simulate the time-dependent closure behaviour, but there are subtle problems with the use of this theory as it cannot simulate the failure processes in the rock. To overcome these problems, continuum and discontinuum elasto-viscoplastic models were developed by the authors. Discontinuum models have the advantage of being able to simulate the creep behaviour of prominent discontinuities. Development of these models has led to useful insights into rock mass deformation and has made the numerical simulation of parameters, such as rate of mining, possible for the first time. A number of practical applications for the mining industry have been developed from this study. Among these are the delineation of geotechnical areas using closure data, use of the data as a hazard indicator and to give warning of large collapses in the platinum mines, identification of areas to be preconditioned in the gold mines, measurement of the effectiveness of preconditioning and improved da

Jan 1, 2007

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

By O. Leuangthong, M. Nowak

"The impact of high-grade data on resource estimation has been a longstanding topic of interest in the mining industry. Concerns related to possible over-estimation of resources in such cases have led many investigators to develop possible solutions to limit the influence of highgrade data. It is interesting to note that the risk associated with including high-grade data in estimation appears to be one of the most broadly appreciated concepts understood by the general public, and not only professionals in the resource modelling sector. Many consider grade capping or cutting as the primary approach to dealing with high-grade data; however, other methods and potentially better solutions have been proposed for different stages throughout the resource modelling workflow.This paper reviews the various methods that geomodellers have used to mitigate the impact of high-grade data on resource estimation. In particular, the methods are organized into three categories depending on the stage of the estimation workflow when they may be invoked: (1) domain determination; (2) grade capping; and (3) estimation methods and implementation. It will be emphasized in this paper that any treatment of high-grade data should not lead to undue lowering of the estimated grades, and that limiting the influence of high grades by grade capping should be considered as a last resort. A much better approach is related to domain design or invoking a proper estimation methodology. An example data-set from a gold deposit in Ontario, Canada is used to illustrate the impact of controlling high-grade data in each phase of a study. We note that the case study is by no means comprehensive; it is used to illustrate the place of each method and the manner in which it is possible to mitigate the impact of high-grade data at various stages in resource estimation."

Jan 1, 2015