Search Documents

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By Yunnen Chen

This work concerns the removal of zinc(II) and COD by means of sawdust obtained as a by-product from locally used wood. The zinc(II) and COD removal study has been carried out batchwise where the influence of physico-chemical key parameters such as tree species, pH value of solution, temperature and contacting time and dosage of adsorbent have been considered. The maximum percent removal was attained at pH 9 all for Zn(II) and COD after about 60 min. The adsorbent can be effectively desorption using 0.1 M HCl. The experimental results showed that ion exchange maybe the major adsorption mechanisms for binding the divalent metal ions to the sawdust. Sawdust was a potential adsorbent for the removal of Zn(II) from the effluent of electroplating industry.

Jan 1, 2009

By S. N. Sinha

The distribution coefficients of lead and silver between copper and matte phases have been measured at two different temperatures. Experiments covered the ranges of 0.009-1.8, 0.07-0.13, and 0-11 wt pct lead, silver, and iron in matte, respectively. The distribution coefficients of lead have been measured at 1405 and 1505 K and correlated with lead and iron concentrations in metallic copper and matte. The values of the distribution coef¬ficient of lead between copper and iron-free matte, at infinite dilution of lead, have been determined to be 3.60 and 4,06 at 1505 and 1405 K, respectively. The distribution coefficient of silver between copper and iron-free matte is independent of silver concentrations and has been measured to be 2.13 and 2.21 at 1400 and 1500 K, respectively. For an iron-bearing matte, the distribution coefficient of silver has been correlated with iron concentration in the matte at both 1400 and 1500 K. From the measured values of distribution coefficients, the Raoultian activity coefficients of PbS and AgS0.5 in copper-saturated matte have been calculated. At infinite dilution, the following equations correlating the Raoultian activity coeffici¬ents of PbS and AgS0.5 with matte- composition and temperature have been obtained: log Y° PbS =1.515 + 1080/T 0.14 NFes lbS Fog YAgS = -0.074 - 425/T + 0.09 NFes. - 0.5

Jan 1, 1983

By Xiangwen Wang

Electrochemical measurements associated with the electrowinning of lead metal from concentrated brine (NaCI) - lead chloride (PbCI,) electrolytes at temperatures in the range 328 to 353°K (55 - 80°C) were conducted. The electrodeposition of lead metal onto a lead rotating-disk electrode may be described by the electrodic reaction: {PbCl 4 2 + 2e- = Pb° + 4Cl-} The deposition-overpotential requirements are low (approximately 41mV per decade of current density - Am+), with a corresponding high exchange current (approximately 0.018 A.cm2). The diffusion coefficient of the electroactive PbC142- species in a 3.5 NaCl electrolyte at 353°K was insensitive to the total PbCI, concentration (0.01 to 0.1M), and its value was found to be (1.21*0.1)~10-5 cm2Is with a temperature-sensitivity coefficient (E,/R) of approximately 1.98x103K-1 (328OK(T<353OK).

Jan 1, 1993

By Ruiqing Li

It is possible to purify some liquid metals by exploiting the difference between the vapour pressure of the bulk metal and the minor constituents or impurities. The rates of purification can be improved by carrying out the process under reduced pressure, that is, so called, vacuum. Some commercial examples of vacuum refining are the purification of molten tin to eliminate trace amounts of lead and the refining of cobalt, also to remove lead. The objective of this paper is to review the basic theory behind vacuum refining technology in order to show how the feasibility of vacuum refining can be determined simply for a particular system by evaluating Olette&apos;s Volatility Refining Criteriont.

Jan 1, 1991

By A. Kontopoulos

Refractory sulfide gold ores or concentrates require an oxidation pretreatment step to yield the contained gold amenable to the subsequent leaching step. The process options for oxidation pretreatment can be broadly classified as follows: roasting, high or low pressure oxidation bacterial oxidation, chemical oxidation, each with a number of alternative suboptions. Roasting and high pressure oxidation are being applied on an industrial scale; the stage of development of the other options range from preliminary laboratory to advanced pilot plant- In this paper, the major technical, environmental and economic aspects of the above processes are being discussed. Future industrial trends will also be considered. Particular emphasis will be placed on the treatment of arsenical ores and concentrates, where safe plant operation as well as, handling and disposal of the arsenic containing products and/or effluents &apos;and residues is of paramount importance.

Jan 1, 1990

By Deborah A. Kopsick

Several minerals were observed and collected in a small gully originating from a weathered coal processing waste (gob) pile in Barton County, Missouri. The rapid alteration of these various minerals after collection suggested that they might represent a dehydration sequence. X-ray diffraction of the dehydrated and rehydrated minerals deposited on the gob pile indicated the presence of the monohydrate and heptahydrate forms of ferrous sulfate, szomolnokite and melanterite respectively. The occurrence of melanterite (FeSO4.7H2O), was limited to isolated areas of ponded water while szomolnokite (FeSO4.H2O), was associated with the outwash areas of the pile. Laboratory dehydration of melanterite collected at the gob pile revealed the formation of rozenite (FeSO4.4H2O), an intermediate form of ferrous sulfate. Szomolnokite was shown to be the stable form of these ferrous sulfates during these experiments while melanterite and rozenite were shown to alter readily. Chemical analysis of szomolnokite revealed enrichment in Fe, Mg, Zn, Cd, Cu and Mn relative to the chemical composition of the gob ad the lechate generated from the gob wastes. Although this gob pile had been weathering for more than 35 years, significant concentrations of trace metals were still being released from the pile through the generation of leachate and the formation of various soluble metal enriched ferrous sulfate minerals.

Jan 1, 1982

By R. M. Lamya

A considerable part of gold encapsulated in some refractory sulphides can be dissolved during sulphide matrix decomposition in non-complexing aqueous media. This has been concluded from laboratory results of gold extraction from pyritic and arsenopyritic concentrate containing 172.8ppm Au, into 10% hydrochloric, sulphuric and nitric acids. The degree of sulphides decomposition in the non-oxidative acids limits the gold extraction from this specific concentrate to about 10%. In the case of nitric acid, the gold dissolution follows the rapid decomposition of sulphides, reaching 32 to 42% of extraction at almost total decomposition of the sulphidic minerals. Accumulation of gold in this acidic and non-complexing solution to several ppm was not affected by the soluble products of the sulphides decomposition. An attempt to explain this gold behaviour is undertaken and some practical implications are discussed. In the investigated concentrate the "soluble gold" is mostly associated with arsenopyrite. This is consistent with the latest findings of other authors that gold disseminated in arsenopyrite can occur as cation Au3+. In a comparative test the gold extraction into highly concentrated chloride solution, in the same oxidative conditions, amounted to 92.34%.

Jan 1, 1995

By Dong-sheng Li, Hong-ming Long, Tie-jun Chun, Chao Ning, Zhen Wang

Iron ore sintering is an essential process in modern iron and steel production. It has the largest emission of the PM (particulate matter) in the iron and steel industry, accounting for about 40% of the total emission. The physical and chemical properties of PM 10 and PM 2.5 in the iron ore sintering were introduced, and the research development of PM emission reduction was also summarized. The potential future development of PM emission reduction by chemical agglomeration and capture in the iron ore sintering process was also carried out. The interface chemistry relationships between PM and polymer, such as sodium carboxy methyl cellulose (CMC) and polyacrylamide (PAM), in agglomerates were also investi- gated in this paper. It is signi ficant to reveal the characteristics of PM and develop the emission reduction technology of PM for the cleaner production of iron ore sintering.

Mar 1, 2018

By Pengfu Tan

The control of converter slag chemistry and slag viscosity has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been used to predict the chemistry and viscosity of converter slag. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on slag viscosity, liquidus temperature of converter slag and skimming operation has been discussed. Some applications of the industrial operations have been presented.

Jan 1, 2006

By Nam-Il Um

Bottom ash contains several ferrous materials (ferrous metals, Fe3O4, Fe2O3, FeS, etc.). In particular, ferrous metals contain heavy metal because Ni and Cr are chemically attracted to iron. Likewise, Cu is used to coat Ni and Cr metals as polish or to prevent corrosion. In this study, an Fe3O4-Fe2O3 double layer (similar to pure Fe) was found to have been formed in ferrous metal during air-annealing in an incinerator (1000°C). A strong thermal shock such as one that occurs during the water-cooling of bottom ash results in the breakdown of this oxidation layer, facilitating the degradation of ferrous metals and formation of corrosion products. Therefore, Fe-ion (heavy metal) oxides may be formed on ferrous metals and may be separated from bottom ash via magnetic separation. This study sought to investigate the separation ratio of heavy metals as magnetic separation and mineralogical formation of Fe-ion (heavy metal).

Jan 1, 2006

By Kimio Itagaki, Torn Matsumoto, Makoto Ohtsuka, Kentarou Harada

"The structure and hydrogen-absorption properties of LaNis thin films were investigated in the present study. LaNis thin films were prepared by a sputtering method with a radio-frequency power, Ws, of 50 -400 Wat substrate temperature, Ts, of323 -573 K. Nickel content of the films decreased with increasing Ws, however, there was no dependence on Ts. At low Ws and low Ts, amorphous films were deposited. In other conditions, the films were polycrystalline. The films prepared at high Ws and low Ts, or at low Ws and high Ts, exhibited only a (h k · 0) peak in the X-ray diffraction profiles. This indicates that the c-axis of crystalline films was oriented parallel to the substrate plane. At high Ws and high Ts, the films with columnar structure were obtained. Hydrogen-absorption capacity of the thin films increased with increasing Ws. The pressure plateau did not appear on the pressure-composition isotherms. The films deposited at high Ts represented a higher equilibrium pressure.IntroductionThin films of hydrogen storage alloys can be applied for an electrode of rechargeable battery or fuel cell, a filter for H1 purification and various kind of sensor. Some studies on the preparation of the thin films of LaNi5 intermetallic compound, which is a typical hydrogen storage material, have been done hitherto. Adachi et al. , 2) and Sakaguchi et al. 3) prepared amorphous and crystalline LaNi5 thin films using flash evaporation of alloy powders and measured the pressure-composition isotherm for the prepared film utilizing a quartz crystal mass monitoring (QC:MM) method. It was found that the prepared amorphous film absorbed hydrogen without disintegrating into the powders and the hydrogen-absorption capacity of the films increased with the degree of crystallinity. Sakai et al. 4) reported that the maximum hydrogen storage capacities of amorphous and crystalline LaNi5 thin films, fabricated by a RF sputtering method using combination targets, were about 40 mA h g-1 (LaNisHo.7) and 160 mA h g-1 (LaNi5H2.6), respectively. Uchida et al. 5, 6) prepared LaNi5 thin films using flash evaporation of alloy powders and measured volumetrically the pressure-composition isotherm for the prepared film. It was reported that the hydrogen-absorption capacity of the films changed by the annealing treatment."

Jan 1, 1998

By Ivan Imris

The common problem of new and conventional technology of copper production is the copper losses in the slags, which may be divided into mechanical and physico-chemical losses. In the first group can be included particles of mechanically entrained or floated unsedimented matte particles which coexist with slag. On the other hand, the physico-chemical losses are caused by solubility of copper in the slag in the form of sulphide and oxide. The copper losses in the slags from different processes has been predicted by calculation from thermodynamic data and compared with those determined by microscopic examination and quantitative electron microprobe analysis. Depending on the forms of copper losses in the slag the reduction of copper losses in the slag or the slag cleaning process could be suggested.

Jan 1, 2003

By Batric Pesic

Solvent extraction of nickel and cobalt from the real leach solutions was studied by using a novel extraction system. The extraction system was a mixture of 2,6-bis-[5-n-nonylpyrazol-3¬y]] pyridine (BNPP) and dinonylnaphthalene sulfonic acid (DNSSA). The BNPP represents a novel molecule, which was designed and synthesized in our laboratory. Real solutions for the study were prepared by leaching of two different cobalt-nickel bearing concentrates, cobaltite [CoAsS] concentrate from Blackbird Mine, Idaho, and siegenite [(Ni,Co)3S4] concentrate from Missouri Lead-Belt. The major strength of the system was the selectivity of extraction toward nickel and cobalt from iron containing solutions. Other metals such as Mn, Mg, Ca, Al and As were not extracted. Due to the irreversibility of copper extraction, its removal from solution was required prior to the extraction of nickel and cobalt. Zinc was not as strongly extracted (i.e. its stripping was readily achieved) as was copper . Flowsheets for the recovery of nickel and cobalt were also developed.

Jan 1, 1997

By N. E. Idenyi

The effects of compositions and firing temperatures on the physico-mechanical properties of blended Nsu fireclay and Nkalaha redbrick clay have been investigated. The clay samples were compounded according to the following ratios: 10:90, 20:80, 30:70, 40:60 50:50, 60:40, 70:30, 80:20 and 90:10 in the order Nsu: Nkalaha respectively, and test samples made and fired at 9000C, 10000C 11000C and 12000C. The properties tested for were the modulus of rupture, porosity, shrinkage, apparent density, water absorption and bulk density. From the results obtained, it is inferred that the blends have a maximum service temperature of 11000C, with the 30: 70 blend presenting the best characteristics. A conclusion is drawn to the effect that the blend could be adapted for the production of ceramic earthenware, electrical porcelain pin insulators, cement manufacture and for refractory linings where temperature requirements are less severe.

Jan 1, 2006

By John R. Turney

The success of the Mclaughlin acid pressure oxidatiun process has proved that a complex hydrometallurgical process can be an economically viable means of treating refractory gold ores. Homestake&apos;s Mclaughin acid pressure oxidation process was commissioned in August 1985 and ts currently operating at design tonnage of 3,000 tons per day. Mineralogical and process studies on the operating plant are discussed to show the improved understanding: of the process and its future applications. These studies are also compared with the initial process development work, thus illustrating the success of the initial scale up considerations.

Jan 1, 1989

By Jorge Alberto Soares Tenório, Flávia Paulucci Cianga Silvas, Denise Crocce Romano Espinosa, Ivo André Homrich Schneider, Erika Gusmão, Daniella Cardoso Buzzi, José Roberto de Oliveira

"This study evaluated the Salvinia sp action on metals biosorption in a synthetic sample of acid mine drainage (AMD) in order to determine the time and amount of metals uptake. Biosorptives tests were realized varying the contact time of 5, 20, 60 and 240 minutes. And keeping constant the follow parameters: pH (2.6), biomass concentration (1g.L-1), temperature (25°C) and agitation (175rpm). In order to quantify the metals concentration captured by biomass, the AMD samples will be analyzed by ICP. Biosorbent, Salvinia sp., will be characterized before and after the biosorptives tests through analysis of SEM and IR. The micrographs indicate the occurrence of micro-precipitation and changes in biomass physical structure. The infrared spectra indicate changes in functional groups present in the biomass before and after the biosorptives tests.IntroductionThe current emphasis on environmental sustainability leads the industry in general, to treat their waste. The human activities are increasing, highlighting the industrial and mining activities, and have promoted the contamination of soil, waterways and groundwater by metals (1). The waste must undergo treatment processes aimed at reducing pollution, and therefore, less aggression ecosystems.This means the importance of studies of economic and effective methods to eliminate these metals from wastewater generated. The bioindicators are good investments in this area. The aquatic weeds are plants that inhabit swamps up from truly aquatic environments. They have several morphological and physiological adaptations that enable them to colonize the various aquatic environments. They are used as bioindicators of water quality and have also been used in decontamination of aquatic environments, production of biomass for livestock feed, fertilizers, soil and fish tanks (2)."

Jan 1, 2012

By Jan Vrestal, Josef Tomiska, Pavel Broz

"Thermodynamic investigations on fcc solid ternary Fe-Ni-Cr alloys have been performed by means of the computer-aided Knudsen cell mass spectrometry. Ternary T.AP.-series (Thermodynamically adapted power series) are used for the algebraic representation of the thermodynamic excess properties. At 1650 K the molar excess Gibbs energy GE is negative over the whole field of stable fcc phase. The molar heat of mixing HE is exothermic in the predominant part of the fcc phase field. Only between the section with a constant ratio of mole fraction Xcr/XNi = 0.64 and the fcc phase field boundary the HE values are slightly endothermic. The results of this work can be used successfully for phase diagram calculations.IntroductionThermodynamic investigations on multicomponent alloy systems such as the Fe-Ni-Cr ternary system including the three binary boundary systems are very time-wasting and usually beset with considerable experimental difficulties. Additionally, the required experimental equipment is very expansive and the obtained results are not always satistying. Therefore it is understandable that many phase diagram calculations are based only on few experimental values of the molar excess free Gibbs energy GE. Consequently, Kundrat and Elliott [1] as well as Hillert and Qiu [2] used in their reassessments of the phase diagram of the Fe-Ni-Cr system thermodynamic data mainly assumed and/or optimized by means of various reasoning.Lee [3] reported recently, a revision of the used thermodynamic description of the Fe-Ni liquid phase is necessary to obtain a better agreement with the experimental data on the bcc/liquid or fcc/liquid tie lines and liquidus temperatures in the Fe-rich region of the Fe-Ni-Cr ternary system than in the previous assessments. This is 'in full agreement with mass spectrometric investigations of Fe-Ni alloys in the liquid and in the fcc solid phase, published earlier [4,5]. Indeed, phase diagram calculations based upon the molar excess free Gibbs energies GE obtained in these studies yield liquidus and solidus lines in excellent agreement with experimental phase diagram data [5]. Nevertheless, these experimental data have not been considered later on any more, not even in the revision by Lee [3]."

Jan 1, 1996

By Tapio Ahokainen, Asmo Vartiainen

"Outotec's portfolio contains a wide variety of smelting solutions for non-ferrous metals. Some of these include flash smelting for primary copper and nickel, flash converting for copper, Ausmelt technology for primary and secondary copper, nickel, tin, lead, and zinc residues and waste, Kaldo technology for secondary copper, lead, and precious metals recovery. Outotec also offers slag cleaning technologies and much more.Company provides complete process solutions tailored to each customer's individual needs. Decades of experience have resulted in extensive metallurgical know-how that ensures the most profitable process choice and optimal performance. Outotec's life cycle technology partnership with their customers spans from the early stages of process solution design through the supply and commissioning of the entire process chain. They include integrated process control and holistic service and support concepts. Continuous research and development ensures that the customer is provided with the latest advancements in process and equipment solutions.IntroductionOutotec develops and provides technology solutions for the sustainable use of the Earth's natural resources. Solutions are ranging from various processes and special equipment needed for metallurgical extraction and mineral processing of ores to the production of refined metals and minerals. The processes include not only the grinding and physical separation of ores but also the smelting and leaching of base metals and precious metals. The company provides engineering services for whole projects as well as life cycle services on the equipment and products that they supply."

Jan 1, 2012

By Michael P. Sudbury

Non-ferrous slags are granulated and stockpiled as an alternative to pit cooling or transporting molten slag to a dump. The chemical composition of such slag is determined by the pyrometallurgical process in which it is produced, while the size distribution is set by safety concerns or a desire to reduce wear of pumps, pipelines and other equipment. Relatively few operations give consideration to the effect of granulation conditions on other properties of the granulate as the material is typically accumulated on the smelter site. It is becoming recognized that slag has many potential commercial uses and carries much of the energy applied to the smelting operation. This paper outlines the findings of extensive work to identify uses for granulated non-ferrous slag, the importance of preparation conditions on the properties, impediments to more extensive use of granulated slag, the real costs of slag stockpiling and the opportunities for further productive research.

Jan 1, 2006