Search Documents

By B. Wasmund, K. Adham, K. O'Keefe, C. Lee

"Metal chlorides (e.g. iron and nickel) can be pyrohydrolysed at elevated temperatures to yield an HCl rich off-gas and a metal oxide product. Typically, the high energy requirement for pyrohydrolysis is provided by the combustion of a hydrocarbon fuel with air. Here, it is demonstrated that the use of oxygen-enriched combustion can result in lower fuel requirements and higher HCl concentrations. In addition, the oxygen enrichment can result in a smaller volume of off-gas and thus, smaller and less expensive process equipment. This new concept can be applied to both the spray roaster (SR) and the fluidized bed reactor (FBR). Similar to the aircombustion case, the oxygen-enriched process can use a direct contact venturi scrubber, to recover energy from the roaster off gas, but at a higher efficiency. The new process also uses an absorption tower for capturing HCl from the roaster off-gas, but generates a stronger HCl solution than is possible with pyrohydrolysis in air.BackgroundIn recent years, the metallurgical industry has become increasingly involved with developing methods for extracting metals, upgrading products or cleaning metallic products by using hydrochloric acid. These applications of chloride metallurgy often result in metal chloride solutions, which should be processed to regenerate HCl for reuse, and to recover the metal value as a product or by-product oxide [2, 3, 4].The pyrohydrolysis of metal chloride solutions has been done in two types of air roasters: spray and fluidized bed. The existing roasters burn a hydrocarbon fuel in air, to provide the required energy for evaporating the feed solution and to provide an elevated temperature for the chloride pyrohydrolysis to occur, according to the following reactions:"

Jan 1, 2011

By I. S. Blair

The Mufulira smelter (1, 2,' 3, 4,) is one of three smelters situated on the Zambian Copperbelt to treat concentrates and other intermediate products produced in the area. Two mining companies, Roan Consolidated Mines Limited (RCM) and Nchanga Consolidated Copper Mines Limited (NCCM) each have 51% Zambia Government participation. RCM operates two smelters, one at its Mufulira Division and the other at its Luanshya Dl vision. NCCM operates one smelter at its Rokana Division (5). The Mufulira smelter was commissioned in 1937 with two reverberatory furnaces and four converters. The final product, blister copper, was cast from a holding furnace. In 1952 two anode furnaces and a common casting wheel were installed to feed a new and adjacent electrolytic refinery. In 1956 the smelter was extended to accommodate increasing production from the new Chibuluma mine and expansion at Mufulira mine. A third reverberatory furnace, a fifth converter and duplicate anode processing and casting facility were added. The Copperbelt smelters suffered a loss of production potential when higher ash content coals were used in reverberatory smelting furnaces from 1966 onwards. This, and the planned production increases from Mufulira and other RCM mines, indicated a smelting shortfall of 55,000 tonnes of copper a year in the combined capacity of the RCM smelters.

Jan 1, 1976

By Shijie Wang

In pressure oxidation leaching of copper anode slimes, than 65% of the tellurium is m' cxtraoted during decopperizing. About l0- 15% of the selenium is also dissolved simultane¬ously by severe leach conditions. Current operation for the treatment of the leachate is to constantly recirculate the leach solution through a bed of copper turnings. The tellurium and sele¬nium are precipitated from the leach liquor as copper telluride and copper selenide and sepa¬rated from the solution by filtration. In order to improve the reaction efficiency and reduce the process cost, viz, minimize the copper addition, cut retention time, and reduce the energy consumption; a chemical reducing agent is studied and the cementation process tested in the laboratory. In this paper, the test results are presented and the process chemistry is discussed.

Jan 1, 2003

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Luciana Harue Yamane

"The present work investigated the effect of inoculums volume on bioleaching to recover metals from printed circuit boards using Acidithiobacillus ferrooxidans-LR. Printed circuit boards from obsolete computers were mechanically processed by comminution followed by magnetic separation, and the obtained non-magnetic fraction was used in the bioleaching experiments. A shake-flask study was carried out on the non-magnetic fraction samples using a rotary shaker at 30°C, 170 rpm and different volumes of oxidized culture solution as inoculums (%v/v): 5, 10, 20, 30, 40, 50 e 60. The oxidized culture solution was prepared inoculating pre-adapted bacteria Acidithiobacillus ferrooxidans-LR (5%v/v) in 200mL T&K medium. Leaching in acidic ferric sulphate was also performerd. The analyzed parameters were pH, ferrous iron concentration and metals analysis (AAS). The results showed that using 10%v/v of inoculums were extracted 99,2% of copper and 60% of aluminum by bioleaching. Zinc, lead and tin extraction were not influenced by bacterial leaching and extractions rate were obtained by chemical leaching promoted by acid medium. Ferric iron leaching extracted less copper (35%) than bioleaching. SEM analysis shown surface difference between samples of non-magnetic fraction before treatment and after bioleaching, showing corrosion pits formed by the bacteria contact.IntroductionWaste of electrical and electronic equipments (WEEE) has been target of discussion due to environmental, political and economical issues involved. Around 17 million of computers are discarded annually in the world due to malfunctioning equipment or because technologies become obsolete [1,2]. In contrast, only the central processing unit (CPU) of computers weights around 3kg. From this data, it can be calculated that 51 million kilograms of CPU waste are discarded yearly. This calculation was performed considering only the CPUs, disregarding the cathode ray tubes and liquid crystal displays of monitors [3,4]. Because of the amount that has been accumulated, e-waste has become a global problem but also can be an alternative source to recover valuable materials [5,6]."

Jan 1, 2012

By H. Matsuda, T. Iwashita, H. Awata, H. Liwei, D. Hirabayashi, Y. Saito, S. Ozawa, Y. Goto

"The present study is concerned with investigating the effect of chemical treatment on enhancing the HCl absorption capacities of coal burnt ash and slag. It was found that the HCl absorption capacity of coal burnt ash discharged from fluidized bed combustor was improved by hydration with water and 5% polyethylene glycol solution. This phenomenon was based on an increase of the specific surface area of treated coal burnt ash. The HCl absorption capacity of hydrated ash with polyethylene glycol solution was almost equivalent to that of standard CaO and Ca(OH)2. In particular, the specific surface area of hydrated ash with polyethylene glycol solution was found to be 19 m2/g, which was more than over eight times larger than that of raw sample. Hydrated slag treated with lON sodium hydroxide solution also showed high HCl absorption capacity, with highly improved surface area. It was found that the absorption capacity of slag for HCl depended on the treatment time, showing the maximum absorption capacity for 12 hours of hydration treatment.IntroductionA large amount of coal burnt ash, slag and dust are discharged from such industrial processes as coal combustion and metal refinery etc., and it becomes an serious problem to recover and diminish these solid wastes because of the shortage of dump sites and subsequent metal elution to the environment. Figure 1 shows the present situation of reutilization of coal burnt ash and slag in Japan [1,2]. It is shown in this figure that these solid wastes are recycled as materials in the fields of earthwork, agriculture and forestry etc. A part of these solid wastes, however, is still dumped to landfill. To decrease this dumped amount, the development of environmentally friendly reutilization technique for these solid wastes is of great importance."

Jan 1, 2000

By Zemin Ma

A novel chromate [Cr(VI)] reducing bacterium was isolated from chromite ore processing residue disposal site of China and identified as a Leucobacter sp. by 16S rRNA gene sequence homology. The minimum inhibitory concentration of strain CRB1 was 820 mg l-1 of Cr(VI). The reduction of Cr(VI) occurred only under aerobic conditions. With an initial concentration of 2.5×108 cells ml-1, 1800 mg l-1 of Cr(VI) was reduced entirely within 38 h under the optimum conditions, at 30 °C and pH 9.0. Increasing Cr(VI) concentrations prolonged reduction process and higher cell densities meant quicker reduction. A blue precipitate was produced during chromate reduction of strain CRB1, which was binding to the surface of bacterial cells and determined as trivalent chromium with electron paramagnetic resonance (EPR) spectrometry. The conspicuous chromate reduction ability of Leucobacter sp. CRB1 suggested a potential for bioremediation of Cr(VI) containing wastes.

Jan 1, 2008

By Richard D. Hangi

Process mineralogy techniques are uniquely applicable to industrial problems related to the extractive metallurgy of nickel, cobalt, and associated metals. Reflected 1ight microscopy, together with selected determinations by scanning electron microscopy-energy dispersive spectrographic analysis and electron probe microanalysis, provides the means to identify the ore minerals cobalt and nickel ores, determine the abundance of each ore mineral, assess the extent of intergrowth between the cobalt and nickel minerals and other ore and gangue minerals in the ores and concentrates, and predict the potential success of cobalt and nickel extraction by grinding, flotation, pyrometallurgical, and hydrometallurgical treatments. In addition, the extent of locking of the cobalt and nickel minerals with each other and with the gangue minerals can be directly observed by reflected light microscopy. Where ores have been treated by hydrometallurgical procedures, reflected light microscopy can serve to determine the causes of excessive leach consumption. Finally, the partitioning of cobalt and nickel between high-temperature synthetic phases produced by pyrometallurgical treatment can be precisely determined by process mineralogy techniques. Case histories from cobalt and nickel deposits illustrate the value of applied mineralogical techniques in the study of cobalt and nickel ores, beneficiation, hydrometallurgial, and pyrometallurgical products.

Jan 1, 1993

By Young-Geun Park

A new decarburization model for the RH system was constructed for calculating the decarburization reaction using a three-dimensional fluid dynamics program. The entire fluid flow in the RH process was calculated by evaluating the shape and volume of the plume zone, formed by Ar gas blown through multiple nozzles on the wall of the snorkel. On the basis of this fluid flow, the decarburizaiton reaction was calculated through establishing the decarburization reaction model, which considers the thermodynamics, reaction kinetics, and the decarburization sites (Ar bubble surface, bath surface, and the CO bubble fomtation at inner sites). The results from this model were compared with a real RH operation results with good agreement. Because it is possible to predict the carbon concentration at various conditions using this model, it may be useful in increasing the decarburizaiton rate. Key words : RH process, plume zone, decarburization, Ar bubble surface, bath surface, inner site, circulation flow rate.

Jan 1, 2001

By Jack S. McPartland

The recent developments on the concentration and recovery of gold from leached gold thiosulfate solutions by solvent extraction, reduction-precipitation, and electrochemical deposition are reviewed in this paper. Alkyl phosphorus esters have been found to extract gold only in alkaline thiosulfate solutions, The recovery of gold increases with thiosulfate concentration in the aqueous phase and with alkyl phosphorus esters concentration in the organic phase with aliphatic hydrocarbon diluents. The addition of ammonia improves the extraction. The extraction of gold with amines in either aliphatic or aromatic diluent decreased in the following order: primary>secondary>tertiary amines. Increase in the extractant concentration at high pH increased the extraction of gold. At pH < 9, the primary amine, RR&apos;CHNH2 with 1&apos;9-23 carbon atoms is the main extractant with TBP as the synergistic reagent and at pH >9, the primary amine shows a synergistic effect on the extraction of gold&apos; with TBP. TheAu(I) ions in thiosulfate solution are reduced by sodium borohydride (SBH) to metallic gold, with particles in the sub micron range, At an SBH/ Au ratio of 6.25, pH = 6, and at room temperature, the I e ppm Au(I) in a solution of ] 0 gil thiosulfate was completely reduced to metallic gold in about 60 minutes.

Jan 1, 1999

By ZHANG Ting

In view of the high consumption and contamination of traditional vanadium extraction technology, a new process of leaching the converter vanadium slag without roasting with titanium dioxide waste was proposed. Extraction mechanism of P204 in the leaching solution had been researched and single factor experiments show that after a prereduction of Fe, and under conditions: ambient temperature，leaching solution original pH=2.5, phase ratio (A/O)=1:3, shaking time 8min, the extraction rate of V is more than 98.62% meanwhile the separation rate between V and Fe is up to 135.3 in the 20%P204-10%TBP-Sulfonated kerosene extraction system.

Jan 1, 2015

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"Abstract: In this work, low temperature carbothermic reduction of Panzhihua low grade ilmenite after ball milling were investigated. The ball milling of ilmenite and graphite were processed in a ball mill. The milling process can attenuate the particle of ilmenite, and the ilmenite characteristic peak were broadened and weakened. The reduction temperature and behaviors are studied on the thermo gravimetric apparatus; lower temperature and higher reaction rate were obtained for the reduction of ilmenite with graphite after milled. The reduction temperature and times of ilmenite decreased to 1000-1025°C and 40-60min via milled for 4 or 8h; Low down the reduction temperature can eliminate the solution of Mg2+ and FeTi03 in a certain degree; the reduced ilmenite has an obvious loose structure, can favored the subsequent procedure such as leaching.1 IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposited in Panzhihua, China. In this reserve, there is about 8.73x108 t ofTi02, Accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [JJ Titanium mineral deposits major classified into Rock type and Placer type. Rock type is the igneous mineral, which have great content of FeO (Relative to Fe20 3) and gangue. The rock textures are compact and almost are complex ore. Rock type Titanium mineral major are ilmenite and titan magnetite ore, difficult to separate the metal ore and gangue. l.21 Thus, the Ti02 grade of Rock type ilmenite much lower than the Placer type (Table land 11). Panzhihua ilmenite are the typical Rock-type, due to the higher contents of MgO, CaO and Si02 and the complex mineralogy in ilmenite in Panzhihua region, making its direct reduction progressively more difficult. Mechanical activation, usually carried out by energetic milling or ball milling, was reported to significantly decreased the reduction temperature and accelerate the reaction rate of reduction of ilmenite with carbon, silicon and Magnesium. f3·(>J It reported that the process temperature were decreased to 600-1000°C and the annealing time were reduced to 30-120min after milled for 50-400 h. Shorter milling time involved was imported for else procedure such as direct leaching. 171 Hardly any research had referred to the carbothermic reduction reactivity of ilmeite milled for a short time as 1-1 Oh. In the present work, the aim is to investigate the reactivity and reaction temperature of carbothermic reduction of Panzhihua ilmenite. The Phase composition and micro morphology of samples are characterized."

Jan 1, 2011

By Dmitri Nassyrov, In-ho Jung

"All relevant thermodynamic and phase diagram data in the CaO-Fe10-CaF2 system were critically reviewed. One set of model parameters describing the Gibbs energy of all phases has been obtained as a result of critical evaluation of the available data and optimization of the model parameters. The Modified Quasichemical Model was used to describe the interactions in the liquid phase. All calculations were performed using the FactSage thermochemical software.IntroductionSlags contaimng CaF2 are of significant interest to the steelmaking community. Notable examples of slags containing significant amounts of CaF2 include Electro-slag Remelting (ESR) slags [1] and mould flux for continuous casting [2]. The role of these slags is, among other things, to refine steel by absorbing inclusions and dissolved impurities. During slag-steel interaction, some iron from the steel will inevitably get oxidized and form iron oxides which will dissolve into the slag. With this in mind, it is important to understand the interaction between CaF2 and Fe,0 for accurate prediction of slag composition and process optimization. A thermodynamic optimization of the CaO-FetO-CaF2 was thus undertaken."

Jan 1, 2013

Heap leaching with thiosulfate is only used in one location for the treatment of a refractory preg-robbing gold ore initially pre-treated with bio-oxidation. The chemistry of thiosulfate leaching is complex. Further work is required to develop a better control of the system. A mild refractory gold ore containing pyrite and chalcopyrite was used in this study to investigate the use of thiosulfate as an alternative heap leaching technology. Preliminary bottle rolls tests indicated that similar gold extraction was obtained with cyanide and thiosulfate. In the column leach test, effects of thiosulfate, copper and ammonia concentrations, and their ratio on both gold extraction and reagent consumption, were assessed. The range of reagent concentration were: 0.1 - 1.0M (NH4)2S2O3, 0.03 - 0.10M CuSO4*5H2O, 1.0 - 6.0M NH4OH. The solid-liquid ratio was in the range of 0.83:1 to 5: 1. Best results showed that 72% of gold was extracted in 50 days with 0.3M (NH4)2S2O3, 0.05M CuSO4*5H2O and 6M NH4OH or a combination of 1.0M (NH4)2S2O3, 0.03M CuSO4*5H2O and 3M NH4OH. The reagent consumption at solid/liquid ratio of 3:1 was 37 - 48.6 kg/t (NH4)2S2O3 and 0 - 0.62 kg/t CuSO4*5H2O. The results of thiosulfate leaching were also compared with cyanide leaching.

Jan 1, 1999

By H. Y. Sohn

"The nonferrous production industry has gone through a remarkable transformation in recent years in terms of developing and adopting new technologies. Technology innovations have largely been driven by the need for greatly improved environmental protection in addition to increased productivity. One of the most notable aspects of the new technologies is their ability to reduce the emission of sulfur and other pollutants to extremely low levels.The current industry trends towards more environmentally friendly technologies are bringing about additional benefits of developing more efficient, technically advanced, and continuous processes in closed reactor vessels. Key aspects of these modem trends include the use of increased oxygen enrichment in the process gas, better process control, reduced manpower requirements, and plant operations with more skilled personnel.Computer simulation and modeling of complex processes have become more reliable, realistic, and thus increasingly useful in metal production. Some of the notable examples are reviewed.Finally, the need and advantages for value-added production in the nonferrous industry are discussed.I. IntroductionMost recently commissioned technologies for nonferrous metals production have been developed largely in response to environmental concerns. One of the most remarkable improvements made by the nonferrous industry in the last decade has been the rapid increase in sulfur capture. Before the start of the last decade, 90% capture of sulfur was considered good. Since then, strict emission regulations have become the norm in advanced societies, although smelters in many parts of the world still operate with limited pollution control. Other emissions and discharges have also been substantially reduced, resulting in much improved working conditions and worker hygiene in addition to the overall environmental protection. The development of the more environmentally friendly technologies has accompanied other advantageous advances made in the nonferrous industry, i.e., the trend towards more gas-tight, continuous processes and larger plants. This has increased the competitive edge enjoyed by the industry in the industrial countries, offsetting the higher costs of labor and pollution abatement that they have to overcome in those countries. Experience has shown that clean technology often leads to a profitable business, because its adoption forces the concomitant advancement of related technologies in addition to the avoidance of penalties imposed by the public on pollution-prone industries. Needless to say, there are other driving forces for new technologies such as reduction of operating and capital costs, improved product quality, and energy considerations in terms of reduced consumption and utilization of readily available sources."

Jan 1, 2000

By D. R. Flynn

The recovery of nickel and cobalt from electromachining sludges in the form of relatively high-purity marketable products has been investigated. The investigation has shown that a series of metallurgical unit operations can be performed to recover nickel and cobalt from electromachining sludges in the form of al kal i nickel ic hydroxide and cobalt sulfate/cobal t metal, respectively. The recovery unit operations for nickel include high pH cyanide complexation, followed by oxidation and precipitation of alkali nickel hydroxide. The resultant filtrate can be treated for cobalt recovery by neutralization and acid baking to produce cobalt sulfate. The cobalt sulfate can then be treated for cobalt recovery by electrowinning. Results from laboratory bench scale test work are discussed in terms of appropriate operating conditions.

Jan 1, 1991

By Guo Xueyi

The dissolution behaviors of valuable metals, lead and zinc, from secondary fly ash generated in municipal incineration plants were investigated using some lixiviants: sulfuric and hydrochloric acids, acetic acid and some chelating reagents including L-asparaginic-N,N-diacetic acid (ASDA), a biodegradable, and therefore, environmentally benign novel chelating reagent. It was found that zinc exists mainly as ZnO, whereas Pb probably as PbOHCI and PbO, and the easily soluble components in SFA are KCI and NaCl. Suitable amount of HCI can dissolve all of lead and zinc from SFA. Sulfuric acid can selectively extract zinc leaving lead in the residue. Ethylenediaminetetraacetic acid (EDTA) is an effective chelating reagent to extract both zinc and lead. Although ASDA and diethylene¬triaminepentaacetic acid (DTPA) can selectively extract more than half of lead from SFA, it would by no means be regarded as highly effective reagents for the extraction of these metal values. Keywords: Lead, Zinc, Secondary fly ash, Leaching, Dissolution

Jan 1, 2002

By Thierry De Nys

A direct leaching process of sulphidic zinc-based concentrates in aqueous sulphuric acid solutions has been developed by the V.M. R & D Department. By a very accurate control of the oxidation potential of the leach solution, this process enables a separate recovery of the zinc, copper, silver, lead and sulphur of the concentrate and makes it extremely attractive for treating more complex ores. The iron, solubilized during leaching, is eliminated out of the zinc solution by means of the V.M. goethite process. Alternative flow sheets for a conventional zinc electrolysis plant are presented.

Jan 1, 1990

By Ken-ichi Machida

"Surface modification of R-Fe-N intermetallic compounds was made to improve their magnetic property and nitrogenabsorbing ability, arid high-performance resin-bonded magnets and nitrogen storage materials were developed: Surface coating for Sm2Fe11Nx by the zinc metal produced via photodecomposition of Zn(C2Hs)2 was effective to avoid the further oxidation in the molding process of the fine powders for bonded magnets and the resulting (BH)max values were improved to -186 kJm-3. Meanwhile, R2Fe17 as the mother compounds for RzFe11Nx was highly active for decomposition of NH3 molecule and subsequent nitrogen absorption as metal nitrides. Furthermore, even inert Nz molecule was dissociated on them by impregnating Ru metal and the resulting nitrogen atoms were absorbed in the crystal lattice of R2Fe17. These results demonstrated that the nitrogen storage system was established by cycling the nitrogenation and hydrogenation of RzFe11/R2Fe11Nx materials.IntroductionProcessing for rare earth metals and intermetallic compounds requires well-controlled conditions in order to avoid the oxygen contamination involved in it due to their high reactivity, as causes the serious damage for materials such as magnets, metal hydride for hydrogen storage, and so on. Rare earth-iron intermetallic compounds, R2Fe17, provide the corresponding metal nitrides (R2Fe11Nx) by heating in N2 or a mixed gas stream ofNH3-H2 [l] and, among them, Sm2Fe11N3 has been particularly noted as one of the promising materials for high-performance permanent magnets such as bonded ones [2- 6]. Usually, the nitrogenation for Sm2Fe17 is made in Nz, but it needs the much more hard conditions of reaction pressure (-10 MPa), temperature (-550°C) and time (-72 h) than the nitrogenation in the NH3-H2 mixture [l]. In the latter case, a significant amount of nitrogen can be interstitial introduced in· the R2Fe17 crystal lattice (x=-7) under the more moderate conditions than in N2 (at 0.1 MPa and -450°C for -3 h) [3-6] and then, in a similar manner as metal hydride systems [7], the excess nitrogen in RzFe1 7Nx (x>3) is reversibly desorbed by heating at a temperature around 500°C in Ar to form the RzFe11N3 compounds. This behavior of nitrogen absorption and desorption has a close relation to the sites for nitrogen in the crystal lattices."

Jan 1, 2000

By Shen Shen, Paul R. Ohodnicki, Samuel J. Kemion, Vladimir Keylin, Alex Leary, Joseph F. Huth, Michael E. McHenry

"Recent DOE workshops highlight the need for advanced soft magnetic materials leveraged in novel designs of power electronic components and systems for power conditioning and grid integration. Dramatic weight and size reductions are possible in these applications through operating at increased frequencies. This manuscript discusses processing and composition design approaches for optimizing FeCo-based nanocomposites for higher frequency operation at 100 kHz and above. The proposed strategy involves starting with prior compositions known to exhibit high inductions, optimal field crystallization induced anisotropy, and excellent mechanical and high temperature magnetic properties. Proposed alloy modifications for the applications of interest would include increased amorphous phase resistance, optimum induced anisotropy, and minimized or carefully engineered magnetostriction. Relevant process developments would target reduction of ribbon thickness by optimizing the casting process or post-processing treatments such as chemical thinning or rolling. Three archetypes FeCo-based nanocomposites are described including near equiatomic FeCo-based, Fe-rich and Co-rich alloys.MotivationSilicon steels are widely applied for 60Hz utility-scale transformers [1]. For applications at high frequencies, however, Si-steels exhibit unacceptable losses and ferrites are typically used due to their high electrical resistivity and good soft magnetic properties [2]. However, the low inductions offerrites have limited their applications in power electronics. Developments in rapid solidification have led to amorphous metal alloys and controlled nanocrystallization processing has resulted in state-of-the-art amorphous/nanocrystalline nanocomposite soft magnets [3-5]. Commercial utility-scale transformers made with Fe-based amorphous materials have been demonstrated to result in significant energy savings with an associated reduction in greenhouse gas emissions [6]. DOE workshops held in 2010 emphasized a need for advanced soft magnetic materials for the next generation of power electronics. For advanced power conditioning and grid integration applications, frequencies of 20 kHz up to -1 MHz are of interest depending on the power level [7]. Here, we review previous work and discuss the approaches to optimize FeCo-based nanocomposite materials for high frequency applications."

Jan 1, 2012

By Yongbin Yang, Meixia Cai, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Jianjun Fan

"A series of sintering and metallurgical experiments were carried out to optimize the blast furnace burden structure in this study. The results indicated that the sinter disintegrated seriously with basicity around 1.4, and after this “turning point”, the sintering properties were improved gradually with the increase of basicity of sinter. Based on the results, an idea was put forward which focused on producing two different kinds of sinter with different basicity. Different with the original burden structure of 85% sinter with basicity 1.4-1.5 + 15% pellets, an alternative new BF burden structure was proposed by the following structure?44% sinter with basicity 1.05 + 44% sinter with basicity 1.87 + 12% pellets. This new alternative BF burden structure has been adopted by some steel plants.IntroductionIn recent years, conventional blast furnace (BF) process was put into operation to produce hot metal in “A” steel plant. “A” steel plant owns two sets of sinter strands at present. Because the sinter production capacity exceeds the actual requirements of BF, a burden structure with 85-90% self-made sinter + 10-15% purchased pellets is adopted to take advantage of the low–cost sinter. But the serious problems encountered with the BF operators are that the sinter disintegrated easily during transportation and storage process. Therefore, the rate of return fines is very high after sinter being screened."

Jan 1, 2012