Search Documents

By R. P. King, M. K. McCarter, K. S. Free

Mine plans typically consider the profits and costs associated with extracting and processing minerals into marketable products. Interrelationships between mine and mill costs are often overlooked during the process of mine plan optimization. A simple and quick method for predicting milling costs for a given block would improve the planning process, especially if the procedure could be incorporated as part of routine ore grade analysis of drill core or cuttings. Incorporating milling costs as part of the mine planning process could improve overall optimization of the mine/mill combination. A method developed by the Utah Comminution Center (UCC) at the University of Utah provides a possible answer to the need for quick and reliable grinding cost estimation (King et al., 1996). Using results from single-particle impact tests, a work index, called the Utah Load Cell Work Index (ULCWI), is calculated. The potential for routine use of the new method is explored by comparing ULCWI values with corresponding Bond Work Index (BWI) values for eight mineral materials (Free, 2000).

Jan 1, 2004

By Richard Klimpel

The laboratory ball mill grinding of coal/water slurries is described for three coals. Emphasis is placed on the measurement of specific rates of breakage for various operating conditions. Corresponding rheological information is also presented based on data collected using a rotational viscometer. A rheological explanation of the influence of various slurry fluidity conditions on the specific rates of breakage is presented. This rheological approach has proved useful In both the identification of suitable chemicals for increasing breakage rates in coal/mineral slurry grinding and in the plant scale implementation of dense slurry grinding systems.

Jan 1, 1982

By R. J. Weege

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. Our work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially' independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept as advanced by earlier writers to explain the concentration of the ore-bearing, fluids into broad shoots con¬stituting entire ore bodies is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body.

Jan 1, 1962

By Douglas J. Pendrell, Marvin D. Simmons, E. Raymond Boc

The U. S. Army Corps of Engineers is in the early stages of design for an estimated 14 m (46 ft) diameter tunnel in northeast New Jersey. This tunnel will carry flood waters from the upper end of the Pompton River in Wayne County, to an outlet in Newark Bay, a distance of 33 km (20.5 miles). The tunnel will be constructed by a tunnel boring machine (TBM), the size of which is unprecedented at the present time. The alignment is through Triassic and Jurassic sandstones, siltstones, and shales that include three beds of basalt that range in thickness from 76 to 310 m (250 to 1020 ft).

Jan 1, 1991

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

On my arrival in New York after the Russian examinations John D. Ryan, president of Anaconda, asked me what my plans were. I told him I wanted to be useful somehow in the World War that we had entered while I was away, but I did not know how. Ryan and Thayer told me that the new American Air Corps was gathering a group of executives, most of them young, to go to France as Army officers to help with the industrial side of our aviation activities. This would include construction of military airports, maintenance, and supply for our rapidly growing Air Corps. They thought I might be accepted in this group of about 30. It seemed to be just what I wanted, and I put in my application at once. My application was accepted about three weeks later and I was told to come to Washington to take physical and other tests and to meet others of the group. I liked them. They were a cross section of competent American manufacturers, bankers, automobile executives, and merchants. I was the only miner. I had many discussions in the days in Washington with members of our organization and others I knew who were going into war service. Attitudes were very different from those 55 years later. There was no discussion as to whether war was right or wrong. We were in it and must do all we could to help. At the same time there was a holdover from the days when, at least for the elite, war was high adventure. Even the most high-minded did not then realize that war is a horrible form of wholesale murder and, in 1917, it would have been treason to suggest this. I had two weeks before our industrial group was to start work which gave me time for a hurried trip to Berkeley where Dorothy and I announced our engagement.

Jan 1, 1976

By Michael Schultz, Gregory Sanders

The City of New Haven is proposing to construct Downtown Storm Sewer Infrastructure Improvement project to mitigate on-going stormwater flooding in the Long Wharf District. The proposed project includes a 200 cubic feet per second (cfs) stormwater pump station; and a 914 meter (3,000 linear feet) long tunnel segment with an internal diameter of 2.1 meters (84-inches). The tunnel alignment will cross under the Long Warf railyard and then continue parallel to the Vison Trail Route. This paper presents the local geology and subsurface conditions, as well as discusses the major project challenges and risks including construction in soft marine soils and encountering remnants of the former wharf.

Jun 13, 2021

MULSIM/NL and La Model are displacement-discontinuity programs which have been used quite successfully in the past to provide detailed structural models of various single and multiple-seam mining situations. However, both of these programs required fairly complex details of the mine plan and topography to be manually input into the program, often taking several days of work. Recently, automatic mine and topographic grid generation capabilities have been added to the MULSIM/NL and La Model programs, reducing the input time requirements from days to hours. This paper discusses the algorithms used for the automatic grid generation and demonstrates the utility of the new capabilities with a case study.

Jan 1, 2003

By E. Topuz, J. Mastoris

The problem of defining the optimum final limits of an open-pit mine has challenged the mining industry for the last three decades. The difficulty results mainly from the great number of variables involved and from the sheer computational effort required in real-life applications. An actual lignite deposit is used in this study to introduce and apply a new methodology that can be used as a basis for surface-mine design optimization. A geologic-reserves model of the deposit is first developed with the use of an integrated geostatistical-modeling package. The model is transformed into an economic one through the use of flexible objective function formulation(s). The final open-pit limits are then optimized using a competent commercial optimizer, and comparative-sensitivity analyses are performed to study the effect of some basic mining and economic parameters on the optimal pit design. The conclusions drawn can develop useful guidelines for decision making by the mine operator.

Jan 1, 1996

By John Carson

Belt feeders are commonly used to meter the flow of bulk solids from bins and hoppers. If the interface between the hopper outlet and belt feeder is not designed correctly, flow from the bin may be severely compromised, resulting in problems of no-flow, segregation, flooding, etc. By knowing the flow characteristics of the bulk solid being handled and applying proven design techniques, such problems can be avoided. Relevant bulk solids flow characteristics are identified, along with measurement techniques. Design procedures for correcting problems with existing feeders as well as proper design of new feeders are presented, along with case histories of successful application of these procedures.

Jan 1, 2008

By Fred J. Fleischauer

Industry requires higher speed sheet stacking. High speed sheet stacking requires equipment and techniques to solve several inherent difficult problems, such as the tendency for sheets to sail, and the need for a means to absorb the kinetic energy of the sheet without damaging the sheet. Accurate alignment of the sheets on the stack is another problem difficult to solve. The paper first analyzes the process of sheet handling into its basic elemental steps. It then describes equipment and techniques presently used for moderate sheet handling speeds, with emphasis on how each step in the stacking process is accomplished by the present equipment. The limitations to speed-up of present equipment is discussed. New high speed equipment, either recently introduced to the market, or in the process of development, is described. Magnetic, air float and vacuum conveyor stackers are compared.

Jan 1, 1973

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By Tuncel M. Yegulalp

In this paper we revisit the well known "Ultimate Pit Limit Problem" and suggest an alternative approach for fast and efficient solution. We follow the approach originally proposed by Johnson and Barnes (1988), but utilize the "Excess Scaling Algorithm" in solving the equivalent maximum flow problem. This algorithm provides significant increases in speed and reduction in memory requirements over the well known Labeling Algorithm of Ford and Fulkerson (1956), enabling one to solve large problems with relatively small computers. We present results of a series: of benchmark tests using this approach against the well known Lerchs Grossman algorithm as well as a brief description of the new algorithm.

Jan 1, 1992

By Robert J. Wise, Mark Alspaugh

Underground longwall coal mines depend on conveyor haulage to transport large volumes of coal from the longwall face conveyor to the mine portal. In the last few years, the need for longer and larger longwall panel conveyors has become very significant. In order to keep conveyor equipment to a minimum and still transport higher tonnages over longer lengths, intermediate drive technology has been developed. The use of DC motors and controls in conjunction with load sharing techniques have a1 so proven effective. A case study of a new longwall panel conveyor at Utah Fuel's Skyline Mine incorporating these design techniques will be presented.

Jan 1, 1993

By André Vervoort, Jef Caers

Compound lognormal distributions serve as new generalized distribution laws for analyzing and estimating ore value distributions or related properties such as the average ore grade. These models are an alternative to the well known lognormal distribution. They are the translation of general geological constraints on the genesis of the deposit cumulated in suitable statistical properties. In this paper a maximum likelihood framework is established for estimating the parameters of such laws or parameter functions thereof. It is shown that under certain conditions maximum likelihood estimation is accurate and efficient in estimating the mean value even when relatively few samples are available. The method is based on a numerical maximization of the likelihood function of these models given the data. Confidence limits on these estimates are set up using resampling techniques such as the bootstrap. By this a complete methodology is presented for inference on ore grade distributions such as is shown in an example of gold data from the Merriespruit mine (South Africa) and the diamond size distribution of the Bougban deposit (Guinea).

Jan 1, 1996

By H. Sevim

In long-term open pit production planning, a series of nested and maximum-value pits is usually generated first. These pits are then considered as possible pushbacks over a number of planning periods. To determine the best pushback in each planning period, the pits are evaluated for their technical and economical feasibilities under certain production constraints. Parameterization is a commonly used technique to generate a series of pits. In almost all cases, however, some of the consecutive pits generated by this technique are too far apart from each other. This is called the "gap" problem. It may make the entire pit series useless for production planning purposes. A new pit gener¬ating algorithm has been developed to overcome the gap problem. Through this algorithm, a series of nested maxi¬mum-value pits can be generated with a controllable size increment. The logic of the algorithm is illustrated through a small hypothetical case. Its capability of generating maximum-value pits that are as optimal as those generated by parameterization and its advantages over parameteriza¬tion are presented through an actual gold deposit case.

Jan 1, 1996

By Ron M. Canon, John M. Begovich

Chromatography, ion exchange, and other techniques based on the interaction of solutes with solid phases offer versatility, high resolution capabilities, and near-universal potential applicability for the separation of valuable constituents in liquid solutions. The expense associated with obtaining reasonable throughput for these separations has been the only, albeit overwhelming, obstacle preventing widescale use of these methods. Attempts to devise continuous (cheaper) systems have previously resulted in moving, or simulated moving, beds of resin with complicated valving and timing sequences. These disadvantages, plus technical problems associated with the disturbing effects of non-plug flow and reduced resolution of moving versus packed beds, severely limit applicability of these systems. Over the past decade a new device has been developed that overcomes many of these problems. It utilizes a slowly (less than one revolution per hour) rotating annular bed of sorbent material with fixed-feed inlet and product withdrawal points. Numerous units of various diameters and lengths have been fabricated and operated, and a parallel effort has developed a satisfactory theoretical treatment of the device. Several simple control systems have been incorporated to thoroughly demonstrate the simplicity of operation, even for multiple products and multiplecarrier flows. This device has been developed using several metal solutions and has demonstrated its power with some of the most difficult, including the zirconium-hafnium, separations. Design equations are available for sizing units based on simple laboratory data and have been tested for units as large as 18 in. in diameter.

Jan 1, 1985

By J. H. Fewings

The rapidly escalating capital costs for new projects, or extension of existing projects, has placed greater emphasis on maximum use of existing resources. Thus, when increased grinding capacity was required to achieve metal production from lead-zinc ores a number of alternate approaches were studied. The most cost effective way of achieving the required 5% increase in grinding circuit capacity was to install upgraded instrumentation and computer control of grinding - Fewings, Wickham and Wiseman (1). Once the computer installation cost had been borne by the financial returns from that project, other projects involving computer control were economically viable on an Incremental cost basis. These Included centralised control of tailings thickening and return circuit water distribution, centralised control of the crushing plant and use of the computer as a data processor for an on-stream analysis system for flotation slurries.

Jan 1, 1979

By A. J. Erickson

In mid 1970, Park City Ventures, a Utah partnership of ASARCO and TAC, initiated a six phase exploration and development program in the Park City District, Utah. Geologic studies had delineated a number of exploration tar¬gets in several areas of the district. Discovery of ore in any of the target areas and continued favorable down dip development below then productive ore bodies would allow for reserve expansion and mill construction. The targets were: Mississippian Humbug Formation replacement mineralization below productive ore bodies on the east flank of the Park City Anticline; Humbug replacement mineralization in an unexplored fault block in the footwall of the Hawkeye structure on the east flank of the anticline; vein and replacement mineralization along the Silver Fissure; potentially higher grade Humbug replacement mineralization in a theorized structural block on the west flank of the anticline beneath the Ontario Vein; Permian Park City Formation replacement mineralization in the West End Shaft Area of the Silver King mine; vein mineralization along the Back Vein in the Judge Mine. Chilean Nationalization in 1971 resulted in a 30% budget cutback. The Judge and Silver King Projects were suspended. In spite of the cutback additional reserves were developed below the Humbug East Flank ore bodies; a major zone of ore grade mineralization was discovered along the Silver Fissure; five new ore bodies were found in the Humbug, and Doughnut Formations on the west flank of the anticline beneath the Ontario Vein. First concentrates were shipped from a new mill in May 1975.

Jan 1, 1976

By H. Wesley Peirce

Arizona, in 1966, has continued to be the site of an extensive and intensive search for metallic mineral deposits. Over fifty separate entities--companies and individuals--have been actively engaged in mineral exploration programs, both large and small, in the Basin-and-Range portion of the State. Certainly, copper has been primarily responsible for the major efforts, although associated gold, silver, and molybdenum mineralization also has been important in the economic evaluation of potential copper deposits. It is not difficult to explain why the Basin-Range portion of Arizona is receiving such attention. Part of the story, undoubtedly familiar to most, can be illustrated by reference to three graphical presentations. For example, Figure 1 shows Arizona's annual copper production for the period 1955-1965, inclusive, and it demonstrates that new records of production have been accomplished in each of the past 6 years and in 9 of the last 11 years.

Jan 1, 1967