Search Documents

By Richard Seal

Nabarlek is situated in the Arnhem Land Aboriginal Reserve about 270 km due east of Darwin in the Northern Territory of Australia. During the dry season (May to November) Nabarlek is accessible from Darwin over the Arnhem Highway-- a distance of 330 km. Throughout the wet season (December to April), except for a few days, access is provided by aircraft from Darwin to the Nabarlek airstrip. Because of the limited access during the wet season, reagents and supplies have to be stock- piled for six months on the site to maintain operations. With the mine and plant being remotely located on private Arnhem land with very limited access outside the site fence, operating personnel are flown to Darwin every six days for their days off.

Jan 1, 1980

By Ian Longson, Darron W. Dixon

This paper describes the results of an investigation into the application of a statistical method for the prediction of general air-body methane concentration in longwall coal districts. An important and necessary part of the research was the acquisition of representative monitored mine environmental and coal production data. The monitored data was used to build time series models of general air body methane concentration, air velocity, barometric pressure, coal production and methane drainage variables of differing timescales according to the Box-Jenkins method of time series analysis. The univariate models were used to identify causal relationships between methane concentration and its explanatory variables. Coal production was found to be the dominant variable in the determination of the quantity of methane emitted and where appropriate, multivariate time series models were built in which expressions for methane concentration in terms of coal production were obtained. Finally, forecasts of methane concentration values were generated from the multivariate models to determine their forecasting capabilities.

Jan 1, 1993

By F. F. Peng, D. C. Yang, G. Yanief, E. H. Cho

This study deals with carrier flotation of cerium dioxide, a surrogate of plutonium oxide, which is the major contaminant at the Nevada Test Site (NTS). The objective of this study was to determine the feasibility of using carrier flotation for remediation of the site. In this study, a - 200-mesh fraction of pure cerium dioxide was used. Oleic acid was used as the collector, while calcium carbonate was used as the carrier. Mechanical-cell tests were conducted to float the surrogate from a mixture containing uncontaminated NTS soil, both in the absence and presence of the carrier. It was found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34% to 65% by adding only 0.5% calcium carbonate (-150 mesh). The recovery further increased to 95% by adding 10% calcium carbonate. The flotation method utilizing a carrier of calcium carbonate seems to have a high potential for the remediation of the soil contaminated with radionuclides at the NTS.

Jan 1, 1998

By Gary H. Higgins

The paper by Lewis and Braun l presents experimental and calculational evidence that primary chalcopyrite ores are rapidly oxidized by warm oxygen-bearing water. Resulting solutions contained copper sulfate products of the matrix rock decomposition such as magnesium sulfate and sulphuric acid. Iron was oxidized to insoluble hematite and hydrous iron sulfates. Oxygen injection near the base of a broken and permeable flooded ore deposit was calculated to cause circulation of oxidizing solutions to the entire permeable region. The rate of dissolution of copper and degree of oxygen saturation for given oxygen injection rates were presented. Their work suggests that in-situ recovery of deep, disseminate primary copper deposits is technically feasible. The actual feasibility depends on economics and environmental safety as well, and it is the purpose of this paper to address these two aspects.

Jan 1, 1972

By A. E. Hall, K. R. Mutama

The wind tunnel has been used extensively for mine ventilation research and continues to be a valuable tool. The advent of the powerful personal computer has reduced the use of wind tunnels because several flow problems car be simulated and investigated quickly. This paper describes the recent design and construction of a wind tunnel which is now being used for mine ventilation aerodynamic research and teaching purposes. The wind tunnel has a square cross section measuring 900 by 900 mm and is 8485 mm long from the entrance to where it joins the fan. The tunnel was designed as an open circuit suction type and is attached to a 7.5 kW variable pitch axial flow fan capable of producing over 6 m3/s of airflow. The entire length of the wind tunnel can be used for flow investigations and all activities are visible since the sides are made of plexiglass. Results are presented from the test program to show that even without honeycombs and screens air flow symmetry is achieved.

Jan 1, 1993

By Pedro Marques Bernardo, Carlos Dinis da Gama

This paper presents a methodology for design and simulation of underground ventilation networks, based on the analysis of real situations, followed by the careful interpretation of the obtained results in order to implement their optimization. The method involves two basic steps: the construction of a complete ventilation data base for the mine, upon a series of care- fully previous surveying studies in order to determine the values of its ventilation parameters, and the simulation of relevant situations for the ventilation system optimisation. A simulation model, modified after the Hardy Cross method, allows the testing of various mechanical means located at different points of the network, aiming to determine the technical-economical feasibility of each solution. These simulations obey the directions of air flow in each point of the mine, as determined by the directions of the natural ventilation flow established in the data base that represents the network. The methodology was validated upon studies developed in ventilation network of the Panasqueira Mine (Portugal), in two situations: regular production (mechanical ventilation) and care- maintenance (natural ventilation).

Jan 1, 1997

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption, and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1987

By S. A. Matthews, M. L. Nave

AC variable frequency motor drives are emerging technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of drive, motor, and conveyor features. The purpose of this paper is to familiarize and inform possible mining users of AC variable frequency drive attributes.

Jan 1, 1998

By Gemei Yang, Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

Laboratory tests on controlled airflow recirculation have shown the development of transient states in response to changes in system prevailing conditions such as those generated by a sudden start-up and stoppage of fans. Researchers in many European countries have developed various models to explain these phenomena. However, these models failed to consider some important factors such as diffusion and dispersion of gas in turbulent flows. For both in-line and cross-cut recirculation, tests have shown that after the start- up of a booster fan, the gas concentration in the system fluctuates, reaching high levels at the initial states and slowly dying out with time. These fluctuations cannot be represented adequately by simple step-wise functions but rather by smooth, albeit complex equations. In this paper, the phenomena are explained by the convection-dispersion theory, and represented by a mathematical model. Based on a few simplifications and applying Fourier's Transform Method to the differential equations of the flow recirculation model, an integral form of gas concentration function was derived. The Simpson Integration Method was used to compute numerical results for two laboratory tests. The paper also discusses the range of the dispersion coefficient to improve the accuracy of the model.

Jan 1, 1989

By S. K. Kawatra, K. A. O, DeLa&apos

On-line sensors and process controls are important for efficient operation of coal preparation plants. The objective of this paper is to describe the current practice in on-line measurement of composition, density, moisture, level, flow and weight. This paper also discusses how on-line sensors can be implemented in process control, and how sensors which are currently being developed can be utilized.

Jan 1, 1988

By C. D. Anderson

"IntroductionTungsten carbide is a valuable material used in a variety of different applications, including the manufacturing of cutting tools, bearings and as a cost-efficient alternative to industrial diamonds. Both the high hardness value (Mohs 9) and scratch resistance of this material make it a valuable commodity for use in the mining industry.Usually, the production of tungsten carbide is a multistep process involving one or more of the following unit operations: hydrometallurgical digestion, solution purification, crystallization (as ammonium paratungstate), calcination, hydrogen reduction and carbon synthesis. The proposed three-step process eliminates three of these steps (crystallization, calcination and hydrogen reduction) by implementing a combination of hydro/pyrometallurgical techniques. These include alkaline pressure leaching, carbon adsorption and carburization roasting. By eliminating some of the intermediate processing steps, there is potential to reduce energy consumption and decrease overall operating costs.Methods and resultsInitially, alkaline pressure leaching with sodium carbonate (Na2CO3) was employed to selectively leach tungsten, as tungstate (WO4 2-), from an industrial Scheelite (CaWO4) flotation concentrate. Experimental variables included lixiviant (Na2CO3) concentration, temperature and residence time. Experimental constants, based on previous work, were percent solids at 13 wt% and agitation at 400 rpm (Queneau and Strathmore, 1969). Leaching results showed it was possible to extract 97% of the tungsten present. The most favorable conditions for leaching were determined: 2M Na2CO3, temperature of 180° C and a residence time of 30 minutes."

Jan 1, 2015

By S. K. Kawatra, S. K. Valluri, S. J. Root

Common carbon dioxide capturing reagents, such as amines and sodium hydroxide, are expensive, toxic, and energy intensive to regenerate. We have added frothers to a sodium carbonate solution in order to increase the surface area available for CO2 transport within the packed bed of a counter current scrubbing column. Addition of frothers has improved the performance of sodium carbonate scrubbing solutions to be on par with sodium hydroxide scrubbing solutions. This novel enhancement of a relatively inexpensive CO2 capture-regeneration cycle shows potential to allow plants to turn a profit by sequestering a waste product. These results are discussed in detail in the following manuscript. INTRODUCTION The combustion of fossil fuels converts chemical energy to thermal energy. CO2 is produced as a byproduct of the reaction. 80% of the world’s electricity is produced by using this thermal energy to power a generator, accounting for 40% of global carbon dioxide emissions. In an effort to stabilize the rising atmospheric CO2 levels, researchers are investigating the application of carbon capture and storage (CCS) systems in power plants. [1] Efforts to capture CO2 at some power plants have been successful, but the cost of installing and operating the required equipment is high. As such, very few power plants have CCS systems. If CO2 can be captured and processed into a product that can be sold at a profit, installing CCS systems in power plants will be a very attractive business decision. In order for the sale of captured CO2 to become a profitable venture, the cost of capturing the CO2 from a flue gas must be reduced. BACKGROUND The most common method for separating CO2 from a flue gas is by passing it through a counter-current packed bed scrubbing column. The flue gas enters the bottom of a column while a solution of a chemical with properties advantageous to the absorption of CO2 is pumped to the top. The fluids interact in a packed bed, where the CO2 is transported from the gas to the liquid. CO2 is an acid gas, so it is common for the scrubbing solution to be alkaline in nature in order to neutralize the carbonic acid that is formed when it is dissolves into water. The exhaust exits the top of the column free of carbon dioxide, which exits the column in the scrubbing solution, reacting or complexing with the absorbent. Figure 1 is a schematic drawing of a CO2 scrubbing column. It shows the molar flowrates and compositions of the gas and liquid at the bottom [1], the top [2], and an arbitrary height in the column [Z]. [2,15] L is the molar flowrate of liquid at any point in in the column. G is the molar flowrate of gas at any point in the column. Since the CO2 is transported from the gas to the liquid, L and G are variable with respect to height. To simplify calculations, the CO2 free molar flowrates Ls and Gs are often used. X is the fraction moles of aqueous CO2 per mole of CO2 free liquid. Y is the fraction moles of gaseous CO2 per mole of CO2 free gas. Figure 2 is a composition diagram of the scrubbing column depicted in figure 1.

Jan 1, 2019

By Robin J. Batterham, Dave J. Robinson

The most significant trend in flotation has been the ever-increasing scale of operations. There is, however, doubt that this ongoing trend is enough to maintain the economics against trends such as falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. We comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10 to 20 years, but in the meantime the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation as we know it will change significantly. 

By Kal V. S. Sastry, Stephen N. Little

Computer simulation of comminution systems is found to provide significant cost savings by enabling efficient circuit design and development of control systems. These simulation systems are based on sound mathematical models and numerical methods. Nevertheless, they are found to be hard-to-use and hard-to-modify to carry out more elaborate process analysis. This paper discusses the fundamental principles and practical aspects of an advanced, highly functional, and user-friendly SIMulator for COMminution, SIMCOM, that is being developed at Berkeley by incorporating state-of-the-art software engineering principles.

Jan 1, 1992

By Gerrit V. R. Goodman, Charles D. Taylor

A technique was developed to determine the fraction of air recirculated from the scrubber exhaust toward the face and the fraction of gas captured by the scrubber. To determine these two values, a series of tests was required. In the first test, gas was released at the face area and concentrations measured at the scrubber exhaust. In the second test, gas was released directly into the scrubber with concentrations again measured in the scrubber exhaust. The simultaneous solution of two independent flow expressions gave values of recirculation and scrubber capture. A series of tests was conducted with various combinations of scrubber flow, curtain flow, setback distance, and machine location. Statistical analyses then were conducted to determine those factors which influenced the levels of scrubber recirculation and scrubber capture in a deep cut. INTRODUCTION As cutting depths increase, the trend is toward the use of blowing face ventilation systems. With these ventilation systems, the potential exists for recirculation between the scrubber exhaust and the intake air stream. One concern is that methane gas, having been removed from the face area, is subsequently recirculated back into the intake airflow. Under these conditions, methane-laden air could be substituted for fresh intake air, leading to increased methane concentrations at the face. There is currently no standard for recirculation between the scrubber and intake airflows. The implied understanding of the Mine Safety and Health Administration (MSHA) is, and has always been, that any recirculation of ventilation air is unacceptable. To minimize recirculation potential, MSHA suggests that operators maintain scrubber and curtain flows within 0.47 m3/sec (1000 cfm) of each other. Given that recirculation may occur in some circumstances, the question arises as to how much recirculation constitutes a hazard for the face workers. Unfortunately, there is currently insufficient information to answer this. Emphasis must instead be placed on means to quantify the amount of recirculation between the scrubber and face area. Methods must also be examined to control this phenomenon. This paper presents a technique for quantifying recirculation and scrubber capture levels in a blowing face ventilation system. Several ventilation parameters are investigated to determine their effects on these levels. DEVELOPMENT OF RECIRCULATION EXPRESSIONS One way to measure airflow quantities at a point near the face would be to measure the gas flow rate Qgas, and gas concentration c at that location. The airflow Qair, would be simply the ratio of these two values, Qair, = Qgas/c. Although gas concentration values, c, can be obtained easily with existing gas monitoring equipment, it is more difficult to obtain gas flow readings, Qgas, at specific locations. To obtain these values of Qgas, another method was needed. Previous work in this area was conducted by Kissell and Bielicki (1975). However, the calculations in their model assumed a constant gas concentration in the region around the continuous miner. In a deep cut, it is questionable that gas concentrations would remain constant or uniform around the mining machine. The technique presented here does not rely on this assumption. It instead assumes that the gas concentration in the scrubber exhaust remains constant. A quantity of gas released at the cutting face either flows into the scrubber inlets or bypasses the inlets and flows around the off-curtain side (in this example, the right side) of the continuous miner (Figure 1). The fraction of the face gas that flows

Jan 1, 1993

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

 The paper demonstrates that Belle Fourche Shale (BFS), an abundant shale, can be transformed into a ceramic through careful characterization and thermal processing. The study explores the potential of BFS ceramics for use as refractories and thermal energy-storage devices, highlighting their high thermal storage capacity, good thermal shock resistance, and cost-effectiveness.

Dec 1, 2023

By J. P. McKinney

Benchtop experiments were performed, in which an electric field was used to enhance separation of water from phosphatic clay suspensions from a central Florida mine. A constitutive relationship was established that relates the increase in solids content to operating time and the applied electric field. An upper limit to the degree of separation was found to be a function of electric field, and the time required to achieve this limiting value was also a function of electric field. The energy requirement for removal of water ranged from 1.25 to 175 Wh/kg water removed as a function of the electric field. A mathematical model was developed that provided good agreement to the experimental values and served to validate the constitutive relationship.

Jan 1, 2011

By A. B. Samaddar

A prototype automated mapping and spatial information management system has been developed, and illustrates how a powerful map manipulation capability and a comprehensive display system can be combined using both raster and vector mapping: The concept of a mapbase and information retrieval mechanism, query language as well as text and graphical menus, is introduced. The Geographic Information System (GIS), which has been built around a system for storage and retrieval of spatial and textual data, allows interaction with geographic space represented on a displayed map. The prototype is demonstrated using maps and information of an open pit mine.

Jan 1, 1989

By S. Bhattacharya, M. M. Singh

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) requires under-ground coal mine operations to prevent "material damage" to renewable resource lands caused by subsidence. However, what constitutes material damage is not defined. This paper discusses the applicable criteria for agricultural lands, forests and grazing lands, surface water bodies, and ground water aquifers. Although data on the subject are limited, an attempt is made to present quantitative guidelines to distinguish between moderate and severe damage due to subsidence.

Jan 1, 1988

By S. Tuylu, D. Adiguzel, A. Bascetin

"Optimization techniques are successfully used in many different fields such as engineering, physics, economy, and politics in order to enhance the performance of the systems. In concrete technology, Aggregates are prepared by mixing the water and cement in proportional quantities. In order to obtain desired quality control parameters, the determination of the ingredients ratios is one of the important problems for the optimization. Additionally, in the quarries where the aggregate quality constantly changes, blending optimization must be made to obtain a sustainable aggregate quality. This study showed that linear programming, which is easy and which includes many aggregate properties, cannot be used in terms of some aggregate properties. Therefore techniques such as nonlinear programming or genetic algorithm must be used. INTRODUCTION Concrete is a used construction material and made by mixing the aggregate, cement, and water. The concrete properties are directly related to the properties of these materials in blending. The quantity of aggregates in concrete is approximately 70 percent of the concrete’s volume. Therefore, the most important material is aggregates. The extraction of aggregate materials in quarries is more problematic because of variable bedrock properties. Therefore, the quality of the materials changes and the characteristics of the concrete are also influenced directly. In terms of sustainable use of natural resources, produced aggregate materials which have different qualities should be used optimally (Adiguzel et al., 2014). Nowadays, in the solution of the blending optimization, various optimization techniques are being used such as linear programming, nonlinear programming, and genetic algorithm. In this study, blending optimization techniques especially used for concrete aggregates blending have been summarized, and the advantages and disadvantages of these techniques have been introduced. BLENDING PROBLEMS Blending is a frequently encountered problem in process-type manufacturing such as mining, refinery, food industry, chemical industry and metal industry (Sakalli 2010). Blending is a commonly used method in lots of practical solutions (Sarker and Newton 2008). Several optimization techniques are available for blending problems (Furman and Pardalos 2009). The most important issue is to blend with minimum cost. The blending problem is a special linear model which was developed to solve this problem. In blending optimization research, linear programming is a widely used method (Adiguzel et al. 2011; Bascetin and Adiguzel 2011)."

Jan 1, 2016