Search Documents

By Tom C. Palanglo, Norbert Maerz

Control of crushing and grinding circuits ideally requires continuous particle size measurements on both in- and outgoing streams. Until recently, size distributions could only be obtained by screening methods, which were neither cost effective, frequent enough, nor timely. Input streams are often composed of large fragments, making screening prohibitive. Optical image processing systems, such as the WipFrag System, have been developed to the point that they are an extremely valuable tool to characterize, control, and fine-tune the comminution process. Although accuracy is less than that of screening, measurements are precise enough to detect relatively small changes in size distributions.

Jan 1, 2000

By Richard Hogg, Heechan Cho

Investigations of long-time grinding of fine quartz (to about 80% passing 0.35 pm) in a 0.6 liter stirred-media mill are described. Breakage rates and primary breakage distributions have been determined based on extensive characterization of the ground products by laser scattering/diffraction and gas adsorption. The results indicate that, while there is qualitative similarity between the breakage parameters for ultrafine and conventional (coarse) grinding, there are important, quantitative differences. In particular, it is found that primary breakage distributions become significantly narrower in the submicron sizes. The trend can be described using double-truncated log-normal distributions in which both a maximum (breaking) size and a grind limit are specified. The breakage distributions become progressively narrower as the size being broken becomes finer. Breakage rates follow a typical, consistent pattern in which the rate decreases with size according to a simple power law. Further decrease in the rates seems to occur after very long grinding times when the entire mill contents become finer than about 1µm. The effect is explained as a result of changes in the rate/size relationship in the submicron range.

Jan 1, 1995

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By Rilung Xu, Jerry C. Tien, Jian Liu

As underground mines become deeper and ventilation networs more complex, ventilation data becomes more complicated and voluminous, making timely ventilation planning and necessary changes more difficult. Oftentimes, ventilation engineers have to rely on special techques using graphs and schematic maps to carry out necessary ventilation planning [1, 4, 5, 6, 9, 10, 11, 12]. A different graphical method, similar to that reported by Taminago and Isobe [10], has been developed in China [13]. This method uses a two-dimensional diagram drawn from available ventilation survey results. It combines both the customary pressure-quantity diagram and ventilation schematic map, and can greatly expedite the interpretation of survey results, facilitate ventilation system design, short and long-range planning, and emergency planning.

Jan 1, 1993

By R. L. Garrett

The quality of mineral additives used in a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally wed minerals are bentonite, barite, barite/hematite blends, and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity and gel strength and to provide a low permeability filter cake. A multimillion dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason oil companies using these materials sometimes set their own quality standards beyond those already specified in APZ Spec. 13A. Also discussed in this paper are the current standardization activities of API Committee 13 on these minerals.

Jan 1, 1988

By L. Shwydiuk, A. Chrzanowski, W. Newcomen, G. Bastin, R. Wilkins

Automated monitoring of steep embankments allows the early detection of instability and can be used to avoid or mitigate possible slope failures. A system that uses multiple and different types of sensors has been created and successfully tested at the Highland Valley Copper mine in British Columbia. The system uses robotic total stations (RTSs) as the primary measurement sensor, with surveys repeated at predefined intervals selected to optimize operational efficiency. A methodology has been developed to improve the system’s accuracy and reliability by reducing the effects of systematic errors created by atmospheric refraction and unstable instrument and reference point positions. The inclusion of GPS sensors to monitor the RTS positions creates additional operational flexibility and maintains system integrity when insufficient reference stations are available.

Jan 1, 2003

By Michael J. Sapko, Robert A. Cortese

A flame powered trigger device has been developed to explosively activate suppression barriers to quench gas and coal dust explosions. The important feature of the device is a silicon solar panel, which collects 0.3 p to 1.1 D wavelength radiation from the developing explosion, and generates electrical energy to initiate a detonator, which in turn causes the rapid explosive release of an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 w of electrical power when exposed to the sun light are producing about 200 w when exposed to full-scale dust explosion propagating in the U.S. Bureau of Mines' Lake Lynn Experimental Mine. The solar panel is electrically isolated from the detonator by a pressure sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame powered photo generator prevents false barrier activation and requires no external power supply.

Jan 1, 1991

By Walter E. McCulloch

Installation of flash flotation in the copper concentrator of Freeport Indonesia in late 1986 and 1987 increased gold recovery by about 13%, while also increasing concentrator throughput. Copper recovery remained essentially the same. Flash flotation has since been included in a recently completed mill throughput expansion to 32,000 t/d (35,300 stpd) as well as in a current expansion to 52,000 t/d (57,300 stpd).

Jan 1, 1991

By J. C. May, G. M. Elliott, J. J. Brady

Increased clearance was required in two railroad tunnels that were built about the time of the Civil War. Clearance infringements, whether they be excavation tights or caused by ice accumulation, reduce tunnel serviceability. Achieving increased clearance often means disturbing the ground and old ground support structures. Access and transportation needs dictate how and when the work can be carried out, and strongly influence the design approach and the methods used by the contractor to execute the work. This paper explores the pertinent considerations of the owner, the designer, the field inspection team, and the contractor in bringing this project to a successful conclusion.

Jan 1, 1997

By R. Candia

The use of industrial wastes, such as quarry fines of crushed stone, should represent a basic component of sustainable development indicators. Therefore, increasing investments should be foreseen in techniques of treatment and recycling of residues in mining, as well as by-product attainment that generate jobs and income. The standards of identification and discarding of industrial wastes vary significantly between countries. However, practically all nations have started becoming more restrictive regarding environmental legislation, especially concerning production, transport, treatment, recycling and final discarding of industrial wastes. Under an environmental point of view, solid wastes produced by a system (such as a quarry) can be handled in two ways: a) they can be discarded in piles or b) they can be internally or externally recycled and reused. This second practice is translated to an additional economic consequence such as an increase of income as well as a decreased environmental impact. This option is more advanced and should be included in company policy. This paper presents cases where this practice is used, i.e. diminishing the environmental liabilities through the use of the quarry fines in the manufacture of industrial devices, incorporating such wastes in the productive chain, instead of storing them in piles.

Jan 1, 2007

By John C. Galloway, Heinz G. Leistner

ACKNOWLEDGEMENTS The investigations described in this paper were supported by contracts with the Defense Nuclear Agency (DNA) under direction of Lt. Col. John Galloway, and by Boeing Company research funds under supervision of James Wooster. Other engineers of The Boeing Company who contributed to the work of this investigation were Don Armitstead, John McAvoy, and Tom Day. INTRODUCTION In this paper, we are describing a current concept for placing intercontinental ballistic missiles (ICBMs) in sites deep underground to be used as a strategic Future Secure Reserve Force (FSRF). The objective of such concepts is to utilize soil and rock cover to protect high value strategic weapons from destruction by nuclear attack. The burial deep underground achieves two purposes. First, it imposes a miss distance upon the attacking weapon equal to the depth of burial minus any penetration capability the weapon might have. This tends to offset increasing accuracy of weapon delivery. The other purpose is to absorb as much of the weapon's energy as possible, thus reducing the effects of powerful weapons. This use of soil or rock cover over military facilities began with the development of man's capability to loft projectiles. Until recently, underground military installations, by their nature, performed defensive functions. Since they are not mobile and their weapons in the past had very limited range, an enemy would have to approach them before an engagement could take place. Thus, they were often used to control "choke points" on sea lanes as in the case of Gibraltar or

Jan 1, 1979

By D. Tao

More than 80 million metric tons of fly ash is produced annually in the U.S. as coal combustion by-product. Fly ash can be converted to value-added products if unburned carbon is reduced to less than 2.5%. However, most of fly ash is currently landfilled as waste due to lack of efficient purification technologies to separate unburned carbon from fly ash. A rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features. Several fly ash samples have been used to understand the effects of major process parameters on the separation performance. The results show that compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator has significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range. Key words: Coal, Combustion Waste; Fly Ash; Particle charging; Separation.

Jan 1, 2008

By A. Goulsbra, S. McAllister, R. Dunne

Since 1992, a tailings gravity re-treatment plant has been in operation at the New Celebration Gold Mine to recover aurifer­ous pyrite (Martins, Dunne and Gelfi 1991; Martins, Dunne and Delahey 1993). The gravity pyrite concentrate is ground in a Tower mill to liberate gold (average particle size around 25µm) prior to cyanide leaching. Although the re-treatment plant has met the predicted gold recovery, based on original laborat01y testwork, there is still room for improved gold recovery. This requires enhanced pyrite recovery, especially in the finer size ranges. The application of centrifugal gravity separators would seem to be an ideal means to achieve this criterion. In particular, the Falcon continuous centrifugal separator (Series C machines) would appear to be ideal for this particular duty. A testwork program to evaluate the application of the contin­uous Falcon to recover pyrite from New Celebration ores was unde1iaken over a six month period during the later part of 1997. The work involved laboratory batch testwork, followed by con­tinuous testing of the Falcon Cl0 (2tph to 3tph) and Falcon C40 (l00tph) units. A summary of the results from this evaluation program are provided in this paper.

Jan 1, 1998

By Richard Gertsch

In the operation of this mobile-modular system, inexpensive fiberglass charcoal columns are loaded with gold at strategically-located adsorption stations. The loaded columns are then shipped to a centralized stripping facility. After stripping, the columns are returned to the adsorption station. The advantages of this system are as follows: •Easy scale up from pilot plant to full production. •Low capital and operational costs. •Gold production quickly reacts to changes in ore production. •The solution circuits are simple and easy to maintain. •Charcoal damage is greatly reduced.

Jan 1, 1996

By Erland A. Tillman

The U.S. National Committee on Tunneling Technology under the aegis of the National Academy of Sciences has long recognized that productivity in major underground construction projects could be increased through better contracting practices and better management. Between 1974 and 1978, this Committee has prepared three reports on these subjects. This paper reviews these reports and their recommendations. It covers the extensive actions by the U.S. National Committee on Tunneling Technology to bring the recommendations to the attention of leaders in the underground construction industry and thus further their adoption and implementation. These activities are continuing. Visibility in this session will give these reports and recommendations increased exposure.

Jan 1, 1981

By A. Afrouz, F. P. Hassani

The types of bulkhead that contain backfill in stopes under various pressures and mining conditions are outlined. Conventionally adopted theoretical and empirical techniques were integrated in the design and construction of each type of bulkhead utilized underground. Methods to monitor the performance of bulkheads are discussed.

Jan 1, 1993

By S. Formby, J. Avraamides

Transportation of sodium cyanide from factory to minesite often attracts adverse comment from both the community and government agencies. In Western Australia the transportation of 30% w/w aqueous sodium cyanide solution raised fears in the community concerning the safety of such material in the event of spillage. The Chemistry Centre of Western Australia initiated a study of the effects of such a spill, to determine appropriate short and long term response strategies. Factors which were considered included the rate of hydrogen cyanide gas release under various climatic and soil conditions and the effect of alternative treatments in reducing such emissions. The data collected have been used to plan emergency response procedures.

Jan 1, 1989

By Steve Richards

Incorporating a bottleneck analysis into the mine plan can provide a significantly better basis to make economic decisions regarding materials handling systems. Every materials handling system has a bottleneck. The bottleneck at a mine may change over time as a function of location or time. Since a mining reserve is a finite amount and can usually only be mined once, knowing how the bottleneck changes can provide a critical backdrop to capital investment decisions, especially those affecting the materials handling system. A bottleneck analysis can better quantify the expected 'return and also indicate the optimal time to complete tile project.

Jan 1, 2002

By Prasannarao Dontula, Kal V. S. Sastry

Advances are made in the field of mineral processing on a continuing basis both in the industry and the academia. These advances do not always get used fully because of the inherent difficulties in the transfer of knowledge and reduction to practice. In recent years, knowledge engineering is being increasingly employed in other fields to overcome some of these difficulties. This paper presents a vision of how knowledge engineering can be applied to the benefit of the mineral processing industry and includes a discussion of associated principles, techniques, and advantages.

Jan 1, 1993

By Werner Stahl, Karsten Keller

Vibration screens are commonly used not only in classifying bulk material but also in dewatering it. The lack of a comprehensive physical theory of dewatering often leads to difficulties in the design and operation of the vibration screens. Firstly, the dewatering of bulk material will be shown, based on a physical model. Because of the oscillatory motion of the liquid in the bulk, the inertial force of the accelerated liquid and the dripping of water out of the bulk or screen must be taken into special consideration. The physical model put forward shows the effect of the various operations parameters of dewatering screens. The comparison between dewatering theory and practice will be shown by measurements using coal, limestone, etc. Dewatering measurements, which have been conducted on a vibration screen, demonstrate that different vibration frequencies and rates of acceleration lead to different residual moistures. Finally, the possibilities of improving vibration dewatering will be described.

Jan 1, 1995