Search Documents

By Adrian Brown

Groundwater inflow and impacts have become major aspects in the permitting and operation of many gold mines. First, the hydrothermal or placer genesis of many of the orebodies being investigated or produced today almost guarantees that mines will be "wet", involving groundwater control as part of operations. Second, the style of ore deposition a1 so often involves a1teration of the host rock, resulting in relatively weak, low permeabi1ity materials that require extensive groundwater pressure control for stable mining. Third, the location of many mines in arid areas guarantees that impacts on water resources will be matters of key focus during permitting and operation. However, groundwater control and protection is a technically difficult area and often involves managerial decisions and activities that do not fit comfortably into traditional mining. In an attempt to overcome some of these difficulties, this paper provides a guide to mine managers and hydrologists as to appropriate strategies for designing, setting up, operating, and evaluating groundwater programs at gold mines that get the job done and are cost effective.

Jan 1, 1988

By Pradip

The selection, testing, and commercial utilization of flotation reagents is best carried out in stages through microflotation tests on pure minerals and their synthetic mixtures followed by bench-scale batch flotation tests on the ore. A systematic approach to quantitatively evaluate different reagents, in particular, through the analysis of batch flotation data, has been presented in this paper. It is recommended that the reagents are compared both in terms of their performance with respect to the recovery-time as well as the recovery-grade plots. While the former describes the kinetic aspects of reagent interaction, the latter is a measure of its selectivity for a particular separation problem.

Jan 1, 1987

By Peri Mehling, Allister Brown

Environmental regulations concerning the processing of gold ores and the treatment and disposal of spent process solutions range from rigid standards in some locations to site specific options in several other jurisdictions. This paper examines the regulations and policies in two North American jurisdictions. Emphasis will be placed on the mill process and waste stream treatment and disposal, and implications for environmental impacts. Case examples of mine licence requirements will be discussed, with brief descriptions of individual treatment and disposal systems. Policies and environ- mental regulations within each jurisdiction will be examined in terms of potential environmental protection.

Jan 1, 1987

By R. Pazhianur

Many investigators conducted surface force measurements between hydrophobic surfaces in water, and observed attractive force that was substantially stronger than the van der Waals attractive force. The excess force was appropriately referred to as “hydrophobic force”, for which many different theories have been put forth by numerous investigators. In an earlier publication (Yoon and Ravishankar, 1996), it was suggested that the hydrophobic force maybe due to the interaction between the large dipoles created by the surfactants adsorbing on solid surfaces in patches (or domains). In the present work, a mathematical model has been developed to further elaborate the theory.

Jan 1, 2003

By Raj K. Rajamani, M. K. Abd El-Rehman

The planetary mill is very much suited for the ultra-fine grinding of mineral fillers. Ultra-fine grinding here refers to grinding powders to a size range 5-1 0 rnicrons. Such powders enhance the quality of the final product. The operation of a specially built planetary mill is described. It is shown that a target size of 5 rnicrons can be reached in a few hours using the dual drive planetary mill. A centrifugal field of 37G is generated by the gyration arm of the mill. The design allows the desired setting of canister critical speed. The ultra-fine grinding of alumina, titanium dioxide, hematite, magnetite, kaolin and silicon carbide are described. Also, the continuous operation of the mill is shown.

Jan 1, 2003

By C. R. Stephan, N. B. Greninger, W. A. Slivensky

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. Over 20 full-scale seals were constructed in the Bureau's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 0.14 MPa or greater. A discussion on the experimental procedure, construction techniques, and the explosion and air-leakage test results is presented. Four types of construction material were used during this seal testing program: solid-concrete-blocks, low-density foam blocks, cementitious foam, and wood blocks. Only one of the solid-concrete block designs using a mortared thick wall survived the explosion and air-leakage tests. Most of the low-density foam block and cementitious foam seal designs were judged to meet the requirements to be considered a coal mine seal. One of the wood block convergence seal designs failed explosion testing. Based, in part, on these research findings, several alternative seal design constructions using low-density foam blocks, cementitious foam, or wood have been approved by MSHA for use in coal mines.

Jan 1, 1993

By S. P. Chong, Peter V. Avotins

The iron and steel industry continues to operate at depressed production levels due to the low level of demand for steel and foundry products. Crude steel production in the Western world dropped by 13.7% from 459.3 Gt (506 billion st) in 1981 to 396.4 Gt (437 billion st). The reduction was particularly severe in North America where the industry suffered a loss of 37.3% from 123.6 to 77.5 Gt (136 to 85 billion st). This reduced level of production severely affected iron ore and agglomerates output. Substantial curtailment was made in both sintering and pelletizing plants to meet reduced demand. The pressure on these plant operators shifted from quantity to quality. With energy cost becoming an ever increasing part of production costs, conservation was a major area of emphasis. Iron Making Sinter has continued to be the favored burden for blast furnaces overseas. As hot metal production declined and excess sintering capacity developed, many of the overseas operators that have been using pellets found it advantageous on hot metal production cost to increase the ratio of sinter at the expense of pellets. This was the case despite the depressed price level of pellets in the world market. In North America where pellets have been the predominant burden material-mainly because it is necessary to pelletize the fine grain iron ores available domestically-there was also increased interest in sinter usage. Bethlehem Steel Corporation's 13.6-m (44.5-ft) furnace at Sparrows Point experimented with a burden with more than 70% of sinter during the second half of the year and indicated some favorable results as compared to its previous 50% super flux sinter and 50% acid pellet burden. The blast furnace operators continued to press for improved burden quality. In addition to the emphasis on the importance of burden chemistry and quality, uniformity, much emphasis was placed on improving reducibilitiy and high temperature metallurgical qualities. These burden properties were recognized to hold further promise in reducing fuels rates. Sintering With reduced consumption caused by the cutback in hot metal production, many sinter plants sat idle while others operated at greatly reduced rates. The deemphasis on production in many plants allowed them to experiment with various means to reduce operating costs. The most notable action was the introduction of low cost South American pellet feed fines into the sinter ore mix. These feed fines, which are finer than 150 µm (100 mesh) ore, were previously thought to be too fine for sintering. However, when the full production rate is not required the use of up to 40% in the ore mix was reported to be successful with the aid of burnt lime and adequate premixing and granulation of the sinter mix before sintering. The emphasis on quality and tighter cost control also has resulted in a further breakthrough in sintering technology. It was recognized that good feed preparation-including selection of compatible ores, good blending, good pseudo-particle formation, additive size control increased bed depth, and closed control of the sintering bed heat pattern-could allow the production of high quality sinters with much lower heat input and FeO level. Bed depth of more than 600 mm (23.6 in.) was practiced in a number of operations. Total heat input of better than 1.3 GJ/t (290,300 kcal per st) has been achieved. Kawasaki Steel's Chiba Works has also achieved a 5.3% SiO2 in the sinter with good quality. The low heat input approach allowed production

Jan 5, 1983

By H. Wagner

INTRODUCTION One of the most important tasks facing the opera¬tors of deep-level gold mines is supporting the roof strata in the immediate vicinity of the stope faces. Some of the deeper gold mines operate at depths ex¬ceeding 3.0 km; the extreme mining depths and the tabular nature of the gold-bearing reefs result in high stress concentrations at the abutments of the stope faces. These, in turn, lead to extensive fracturing of even the hardest quartzites. Although most of these fractures develop in a stable manner, there have been many instances where rock failure occurred suddenly, resulting in a considerable amount of damage to the underground workings. Such violent rock failures commonly are known as "rock bursts," and they are typical of many hard-rock mines that are operating at great depths. To safeguard mining personnel and equipment against the effects of stable and unstable rock failures, adequate support must be provided to the fractured roof as quickly and as effec¬tively as possible. Traditionally, timber props and timber packs have been utilized to provide roof support in gold mine stopes up to 1.5 m wide. Both methods of support suffer from the fundamental disadvantage of generating sup¬port only in reaction to movement of the strata. Since unrestrained strata movement often results in a break¬down of the frictional forces that preserve the stability of the intensely fractured roof strata, it is essential that stope supports have rapid load-bearing characteristics. An equally important requirement is that the roof sup¬ports be able to accommodate displacements of the rock mass. A third requirement of roof supports in gold mine stopes is that they must be able to accommodate the high rates of stope convergence typical of rock bursts. The hydraulic prop is the obvious choice for sup¬porting the stope faces in deep-level hard-rock mines. Since hydraulic props can be installed with a positive setting load, they can provide roof support that is independent of strata movement. By equipping the hydraulic props with yield valves, they meet the require¬ment of being able to accommodate rock-mass displace¬ments. However, the requirement of being able to accommodate high rates of stope convergence without overloading or damaging the rock strata was rather difficult to meet. The first introduction of hydraulic roof supports into gold mine stopes showed that conventional hy¬draulic props, such as those used in coal mines, were completely unsuitable for a number of reasons, in¬cluding: 1) Since drilling and blasting are used to break the ore in gold mine stopes, supports installed close enough to be effective are exposed to the vigor of the blast. Conventional coal-mining props suffered extensive blast damage, despite being protected by a blast barricade. 2) The environmental conditions in gold mine stopes favor corrosion. The high quartz content and the abrasiveness of the ore further aggravate the problem by damaging the protective coatings on the hydraulic surfaces. Simply changing the design of gold mine props to have the piston project from the bottom rather than from the top resulted in dramatic improvements in the service life of the props. The improvement was attributable to external water in the stope washing the fine quartz grit away from the hydraulic surfaces, rather than concentrating the particles between the cylinder and piston of the prop. 3) The most obvious deficiency of conventional coal mining props was their inability to yield rapidly enough to accommodate the high convergence rates of rock bursts without overloading the supports. As a result of the first disappointing results with hydraulic supports in narrow hard-rock stopes mined by drilling and blasting, a comprehensive research and development program was undertaken. The hydraulic props resulting from several years of research and exten¬sive field trials are described herein. To date (1978), more than 130,000 of these props have been manufac¬tured and used successfully in a number of mines and under a variety of geological conditions. Although many of the detailed specifications are directed spe¬cifically to gold mining conditions, there are a number of points that are of general importance in the design of underground support systems for tabular excavations in hard-rock mines of any type. SPECIFICATIONS FOR RAPID-YIELDING PROPS Yield Requirements The yield requirements for hydraulic props in deep¬level hard-rock gold mines are summarized in the fol¬lowing paragraphs. Slow Yield Load: The design of the yield valve must allow the yield load to be preset to between 300 and 400 kN. This flexibility is necessary to account for the differences in the strength properties of the roof and floor strata. Drop in Load Under Slow Yield: The drop in sup¬port load during a slow yield should be as small as possible, but it should not exceed 5% of the slow-yield load. Rapid-Yield Load: The load exerted by the prop during periods of rapid stope convergence should be as close as possible to the slow-yield load. The rapid-yield load should not exceed the slow-yield load by more than 15% at yield rates of 1.0 m/s. The limitation of the upper valve of the yield load is important; it deter¬mines the hydraulic performance of the yield valve. The hydraulic props that satisfy this criterion have performed well, even under severe rock bursts. Load Changes Under Rapid Load: On some of the earlier rapid-yielding props, conditions of dynamic in¬stability were observed; these conditions resulted in a complete breakdown of support resistance. It is essen¬tial that the force oscillations during rapid yielding be as small as possible, not exceeding -*5% of the average rapid-yield load at a yield rate of 1.0 m/s. Longitudinal Resilience: During rock bursts, vibra¬tions of the roof and floor sometimes are observed. To

Jan 1, 1982

By W. J. Pennstrom, J. R. Arnold

This paper focuses on solution-balance management around heap-leach operations. Experience has shown that increased leach recoveries can be achieved by utilizing various leach-solution recirculation techniques. The most prominent solution-recirculation technique is intermediate leaching. The net effect of intermediate leaching is to increase recovery plant performance by increasing solution concentration tenors, to increase metal recovery by increasing the total leach time and to decrease the overall capital expenditures required for metal-recovery facilities. The adverse effect on the flow of cash from increased metal inventories in the recirculating solutions is offset by increased metal recovery and lower operating costs per unit produced.

Jan 1, 2000

By R. L. Grayson

In 1995, the United States Congress abolished the Bureau of Mines in the US Department of Interior. But Congress preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the US Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the rnerger of the former Bureau of Mines with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data-informed" priority setting. This paper reviews the current surveillance information concerning the level of injury and disease from mining work and discusses how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 2000

By Robert F. Baker

Neanderthal technology is a harsh and inaccurate way to describe modern underground construction and mining practices, but such an exaggeration helps to focus on a major problem or wasted opportunity of modern society. Why is it not safer to excavate in the underground? Why are the working conditions still so unfavorable? Why are urban freeways, shopping malls, warehouses, power plants, sewage disposal treatment plants, and similar facilities still constructed on the surface of the ground--because it is a better location? On the contrary, if underground technology made full use of existing knowledge, underground resources and space would be much more effectively used. And why is the technology so inadequate? Certainly, researchers and practitioners are aware of the shortcomings and are equally aware of problems that have to be overcome. One of the most important reasons has to do with the type of policy goals that society has set in the past. Policy makers may have agreed that improvements would be desirable but no serious commitments have been made--that is, there has been no major allocation of resources to advance these technologies. And yet, to bring about significant changes will require significant time and resources. The resources that are needed are far in excess of what industry can afford to invest, particularly since the pay-off may be far in the future. So the problem reverts to society in general. As long as society is willing to tolerate the present costs and safety requirements for recovering minerals and for constructing underground facilities, then the changes will be slow in coming. Until such time as society sees and desires the benefits

Jan 1, 1974

By Sukumar Bandopadhyay

A present dominant problem is that of high downtime of the longwall shearer used in the coal production process. The means by which this problem can be overcome are many, but one of, the most important ones is that the-use of an expert system can reduce diagnostic and repair time. In this paper, a fault-diagnostic expert system model is presented. Specifically, the diagnostic architecture of the longwall shearer expert system and its use for diagnostic reasoning are discussed.

Jan 1, 1989

By L. Rainey, W. E. Wallace, B. L. Razzaboni, P. Bolsaitis, V. Vallyathan

The hemolytic activity of milligram-sized mineral dust samples from coal mines collected in personal dust samplers were measured by a modified Harington assay method which increases the sensitivity of the technique. Measurements were conducted on a large number of samples from different mines characterized for gravimetric quartz content and the relative bulk concentration of common contaminants (Al,Ca,Fe). The results of these measurements were compared to the hemolytic activity of pure quartz and of mineral samples obtained from roof-bolter dust boxes of two coal mines. No correlation could be established between hemolytic activity and the compositional variables tested. The results suggest that the distribution of minerals among individual particles and the surface characteristics of particles, rather than the bulk concentration, determine the hemolytic activity of respirable mine dusts.

Jan 1, 1991

By R. L. Grayson, G. Mishra

Introduction Many old underground mines have been developed extensively into reserves requiring large numbers of workers to maintain and rehabilitate lengthy track haulages and/or belt conveyor systems. Often, large numbers of fans are required to maintain minimal airflows in areas where poor conditions and huge leakages prevail. Problems that beset one such coal mine and projects undertaken to restore it to potential profitability are presented. Brief history The Vesta No. 5 mine was opened in 1908. Drift development began near the Monongahela River, which was the primary avenue for shipping metallurgical coal to coke ovens in Pittsburgh. Over the ensuing 75 years, the main haulage entries were developed a distance of 16.1 km (10 miles) to the present mining area. Track haulage was used to transport coal from working sections to the river loading facility. As haulage distance and areas of high water influx increased, management decided, in 1973, to construct an underground conveyor belt system. The project spanned 36 months and culminated in a system of 22 flights, ranging from 205.7 to 1767.8 m (675 to 5800 ft) long. Six intake and eight return entries were developed as the mains were advanced. These entries provided adequate ventilating capacity over the years, but as extensive gob areas progressed and roof conditions deteriorated, the entries became inaccessible and more resistant to airflow. By 1981, five fans were being used to circulate 943.9 m3/s (555.5 cfm) of air through the mine. An average of 6440 t (7100 st) were produced from 20.8 continuous miner unit shifts and 2.7 longwall unit shifts each day in 1981. The ratio of support to production personnel was 1.94. To maintain the outby 16.1 km (10 miles) of haulage, 110 personnel were used. The average cost per ton was $43.54 ($39.58 per st), resulting in excessive bottom-line losses. The mine possessed a rather promising reserve, mostly in lease, of good quality, medium-sulfur metallurgical coal, but it also had a number of formidable operating problems. Operating problems Contributing factors toward relatively low productivity and high costs were the conditions of the track haulage, conveyor, and ventilation systems. Productivity was affected greatly by downtime associated with the conveyor system, which lacked adequate access for making splices or other repairs. Many areas within the conveyor belt entry itself required more

Jan 1, 1988

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By R. L. Loofbourow, Robert R. Miller

Deep, stable, unlined space promises secure, efficient, acceptable solutions to several current problems. With truly favorable conditions, it can be economic as well. The basic requirement is sufficient sound, tight rock at required depth. This and unusual surface requirements point to special testing. An objective is to describe conditions for planners, estimators and contracts. A first stage concept study needn't be prolonged but should overlook nothing significant. Although observations and tests on core are considered essential, time and expense can be cut by supplementing then with tests on walls of rotary or percussion holes. In some places initial drilling could be shallow.

Jan 1, 1981

By William S. Eaton

Managing a mine or mineral processing operation in today's environment presents many unique challenges to mining companies. In recent years, headlines around the world have publicized major incidents such as those associated with the Marcopper Mine in the Philippines, the cyanide release in Guyana from the Omai gold mine and numerous other mishaps associated with mining. These notable upsets were due to engineered system failures, either during normal operations or as a result of uncontrollable events. There fore, many mining firms are attempting to assess their overall risks and establish some priority for expenditure of limited operational and environmental budgets. Failure of an engineered component can have dire operational consequences that affect profitability until repair or replacement can be completed. In addition, there may be significant environmental consequences associated with the engineered system failure. This, too, may affect profitability for an extended time or even the viability of an operation. An engineered risk assessment (ERA) can support a mining company's efforts to cost effectively manage environmental risks associated with the operation of its facilities. The ERA approach also provides information about the current condition of engineered systems. This ERA approach provides a systematic review of the risks of an engineered system failure and the possible associated environmental consequences at mining company facilities. This approach has been successfully applied to many industries and types of engineered systems (Barneich et al, 1996; Whitman, 1984; Power and Tomkins, 1974; Keeney, Nair, and Kulkarni, 1979). This approach evaluates all mining and mineral processing facilities located at a single site and compares them with similar facilities located at multiple mine sites. The ERA approach has been applied to a mining, milling, smelting, leaching and refining operations. These assessments can be part of a comprehensive environmental program to aid in the recognition and cost effective management of the potential environmental risks associated with the operation of facilities. ERA results support plan-

Jan 1, 1997

By Ch. Roumpos

The present contribution investigates the way of applying benchmarking for large-scale open-pit mining operations based on sustainability indicators proposed by numerous institutions or groups of experts. These indicators have been developed taking into consideration the legal and regulatory framework that are in force. However, their scope is not only to declare the mining company?s compliance with all legal requirements but also to represent its economic, environmental, and social performance. In this way, sustainability indicators allow assessment of a company?s capacity to produce commodities, to meet the environmental quality requirements and to contribute to a long-term economic, cultural and social development of the local communities.

Jan 1, 2007

By D. B. Desai, J. T. Waggoner, J. S. Hill, R. R. Redd, S. J. Klein

The 13 km (8 mile) long Riverside Badlands Tunnel is planned for construction starting in 1998. Extensive geotechnical investigations indicate that the 3.7 m (12 ft) finished diameter tunnel will be excavated through soft ground, weak sedimentary rocks, and heavily fractured metamorphic rocks. Nearly 80 percent of the tunnel will be excavated beneath the groundwater level. Tunneling conditions are expected to range from raveling and over-stressed in the sedimentary rocks, to blocky and seamy/crushed with some squeezing in the metamorphic rocks. Two alluvium reaches will require dewatering. The variable and interspersed ground conditions are expected to be a key factor in selection of tunneling methods, equipment, and initial support.

Jan 1, 1997

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical characterization is increasingly used in the mining industry to model ore types, predict process performance and identify potential recovery issues ahead of time. However, most geometallurgical assessments are based on bench- or laboratory-scale analyses of relatively sparse samples, leaving most of the orebody characteristics known only by inference until the rocks are actually mined. In this pilot study, we test drone- and tripod-based hyperspectral imaging for mapping mineralogy across mine highwalls, dumps and leach pads. The results show that hyperspectral imaging can successfully map the types and distribution patterns of key minerals (especially carbonates, sulfates, clays, other phyllosilicates) and other important features (such as lixiviant ponding on leach pads), bringing geometallurgy into the field to provide crucial inputs to process decisions.