Search Documents

By Tracy T. Morris

The current state of the mining community has made it imperative for operations to reduce costs and increase productivity in order to remain competitive. This has been done in Colorado with the installation of an Outokumpu flash flotation machine for the production of a gold/silver/lead concentrate.

Jan 1, 1987

By T. W. Camm

In this US Bureau of Mines report, mine and mill cost models are presented to make estimates of the cost to develop mineral deposits in the desert region of the southwest United States. Regression analysis was used to generate capital and operating cost equations for each model based on daily production capacity. These models are used for Potential Supply Analysis (PSA) studies by the Bureau, which analyzes the economic benefits of minerals in a region.

Jan 1, 1995

By Peter C. Lighthal, Harvey N. McLeod, Iain G. Bruce

This paper describes the practical aspects of handling cyanide leach tailings. Alternative systems for cyanide destruction are briefly discussed. The provision of adequate retention time to allow natural degradation of cyanide during summer months is the most economical method of cyanide destruction. Cyanide in ground- water can frequently be both persistent and mobile, so that tailings basins should be designed to limit seepage. Common methods for limiting seepage are presented. Other aspects addressed are water balance, winter operation and abandonment of cyanide tailings systems. A case example of the Cheni Gold Mines Lawyers Creek Project tailings handling system is presented.

Jan 1, 1987

By Koehler Stout, Leroy Friel

INTRODUCTION Hydraulic sand fills have been extensively used in the United States in deep metal mines since 1940, and hydraulic fills have been placed in coal mines in Europe for many years. Numerous surface hydraulic fills exist in Appalachia for the disposal of coal mine waste and throughout the United States for the disposal of other mining, manufacturing, city, and paper company wastes. Hydraulic fills, as they are now deposited in stopes in mines, are often deposited at near minimum density and hence provide very little support to stope walls and pillars. If the support strength of fills could be increased, perhaps ground conditions in deep mines could be improved making them safer and more efficient. Surface fills deposited at higher densities could be covered with top soil upon which grass could be planted. The purpose of this paper is to describe procedures where the support strength of hydraulic fills can be considerably increased, and the focus of the paper is on applications to deep mines. In deep mines the objective of increased fill strength is to reduce heavy ground problems, improve destressing techniques, reduce or eliminate rock burst incidences, provide better working conditions, provide wall support so that more or all ore pillars can be removed, and improve mine safety, efficiency, and reduce surface environmental problems. The authors have shown that it is possible to improve fill strength used in deep mines. This paper reports the slurry filling procedure, fill testing techniques, and some recommendations for application in deep mines. Some of the reasons for low strength hydraulic fills are:

Jan 1, 1979

By S. W. Kan, M. G. Kakarkis, J. Zelanco

Grouting has been used in underground mining for more than 20 years. Chemical grouting is often used as a remedial measure when the implemented ground-control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. The utilization of polyurethane grout is restricted by its limited range of physical and mechanical properties. To overcome some of the drawbacks of polyurethane, research is being conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as Strata Grip, provides a number of features, including variable gel times and a much-reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted The assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1999

By Karl J. Ellefsen

A geophysical investigation can provide valuable geologic information needed to characterize sand-and- gravel deposits and can be an attractive complement to more common characterization methods such as drilling. Although such investigations have been conducted already, a comparison of the different geophysical methods used in these investigations apparently has never been done. For this reason, a study was initiated by the Mineral Resources Program of the U.S. Geological Survey to determine the advantages and the limitations of different geophysical methods when used to evaluate alluvial sand-and-gravel deposits. The study is focused on those geophysical methods that are commonly available, because these are most likely to be used by industry. Furthermore, the study is focused on surface geophysical methods. Heretofore, four different methods have been evaluated. Three of the four methods-time-domain electro-magnetic (TEM) soundings, frequency-domain electro-magnetic profiling, DC-resistivity soundings-are similar in that they all measure the electrical resistivity of the ground with depth. Ground-penetrating radar, however, maps changes in the dielectric permittivity and for the electrical resistivity with depth. For all, four methods, the objective is to relate the measured physical quantity to the stratigraphy of the alluvial sediments.

Jan 1, 1999

By Frederick P. Schwarz

Sample preparation and analysis can impose devastating errors on assay data. Minimizing these errors by testing and procedural redesign may be critical to assure representative assays and project success. Replicate samples, taken at any volume-reduction and/or analytical step in a sampling procedure, generate replicate assay values whose relative differences constitute a set of data. Variance of this data judges the addition to total sampling error imposed by the step generating the replicates. A variance more than (11.5%)' is excessive for a single step. Sample volume increase and/or comminution at a step will reduce variance for that step. Rejects from well mineralized intercepts can provide bulk samples for testing.

Jan 1, 1989

By Y. J. Wang

A subsystem-based approach to the characteristic curves for a multiple fan ventilation system is presented. The ventilation variables and their relationships associated with a fan branch are considered as a subsystem of the multiple fan system. For each subsystem, the solution curve is generated by replacing the fan with a hypothetical pressure source or, alternatively, by adding a hypothetical pressure source without removing the fan. The projection of the solution curve onto the coordinate planes results in two classes of subsystem characteristic curves: pressure-vs.-quantity and quantity-vs.-quantity. The subsystem characteristic curves are described and illustrated through example ventilation systems. These curves are also discussed using the network equations of a general multiple-fan system.

Jan 1, 1993

By Miroslav Cervenka

The Coal, characterized by coal quality parameters as for example, ash content (Ad), moisture (Wrt), heat content (Qr1), sulphur content (Sd) and other parameters is still in many countries the basic source of energy. Energy is life, especially in modern society, where the demand for ecologically clean energy is very high; and therefore, there is great importance in effective coal utilization Direct utilization - burning of coal for energy generation, is still one of the most effective methods. In most cases, it is one of the cheapest energy transformation methods in spite of the fact that this energy transformation is connected with the deterioration of our surroundings. Deterioration can be substantially reduced if the burning of coal at power stations, heat power stations and other coal consumers is optimized. That means the burning is done in steam boilers, the technical state of which is very good; the coal has minimimum .variations with respect to the projected values; and the burning process is controlled and checked not only from a regulation point-of-view but also from an ecological point-of-view. The instrumentation capable of measuring the characteristic coal quality parameters in real time exists and it forms the basic assumption for the work our research team has made. The proper application of this instrumentation is able to provide information for burning process optimalization. It is the main topic of this paper, which is the compilation of the information on our work -made during the last five years. The whole information is based on practical experience and applied systems in Czechoslovakia in the mines and power engineering industry. See [Cervenka, 1989]

Jan 1, 1992

By Stanislaw Wasilewski, Zdzislaw Krzystanek, Boleslaw Firganek

The experimental system for mine venti1ation control in Staszic colliery has two - level structure. In the lower - measuring 1evel the existing computer - based early fire detection system has been used completed with a number of additional sensors needed for ventilation parameters monitoring. The higher 1evel is a secondary computer equipped with a suitab1e dedicated software performing data processing according to the control a1gorithm. Direct control of air flow in a selected mine district is performed by means of a remotely controlled automatic regulator. Apart from functional tests of the system and its elements some research work has been carrying out in the colliery based on observations of transient effects caused by changes in air flow distribution.

Jan 1, 1989

By P. C. Thakur

Mine productivity, measured by the output of minerals per manshift, depends on a number of factors including physical conditions of the minable seam, type of mining equipment, management techniques, worker attitudes and governing jaws and regulations. The greatest scope of improving productivity lies, perhaps, in modifying physical conditions to an advantage and using highly productive equipment. In the case of coal mines, increased productivity can be achieved by (i) obtaining prior knowledge of the mineable property, e.g., the grade and thickness of, the coal seam, presence of sand channels, faults, etc., (ii) eliminating conditions that hamper production, e.g., high emissions of methane and water, and (iii) using more productive mining techniques. Conoco/Consol's (Conoco Inc. and Consolidation! bal Company, a fully-owned subsidiary) horizontal drilling system was developed with the hove objectives in mind. It can drill 75 to 1001 in diameter boreholes to depths of more than 600 1 and maintain the borehole in a preselected horizon. Such boreholes can be utilized for premining exploration of the coal seam, for removing methane and water and in devising mining techniques with high productivity. The purpose of this paper is to describe the horizontal drilling system briefly and to discuss its applications in the above-mentioned- areas.

Jan 1, 1980

By R. C. Fox

The geophysical aspect of reconnaissance marks the beginning of extensive computer applications supporting development of a mine. Although there are some storage and retrieval applications in geology, and some statistical analysis in geochemistry, large-scale compilation, reduction, and interpretation of mineral resource data are initiated in reconnaissance geophysics. The reasons for this fact are quite simple. Geophysics is oriented toward quantitative evaluation of areas of interest, and methods of data collection are automated to the extent that large amounts of analog and digital information are recorded. The large volume of data must be interpreted in a reasonable time. Furthermore, some modeling problems involving complex numerical solutions could not be attempted without the computer. Therefore, the computer is essential to the success of an exploration project using geophysics. For example, aeromagnetics is a common technique for reconnaissance examination of areas associated with sulfide systems and porphyry deposits. An area covering 161 X 161 km (100 X 100 miles) may be flown with a 1.6-km (1-mile) line spacing yielding 10,000 line miles (16,093 km) of data. If only 10 measurements are recorded per mile, 100,000 data points, including location and magnetic field intensity, must be reduced and stored for quantitative interpretation. Computer applications often represent a significant investment in manpower and hardware. It is desirable, therefore, to initiate an engineering approach to the application of computers to geophysics. By this it is meant that computer programs and systems should be formulated, developed, and implemented in a disciplined manner such that their usage is dependent only on the application and not on the individual doing the programming. In other words, computer application, development, and usage should evolve beyond the personal gadget phase to an important applied technology. Geophysics has evolved over the past two decades in a course parallel to computer hardware development. During the sixties, the computer became large enough and fast enough that complex models required by geophysics could be solved. Automation also relieved the geophysicist from routine manual calculations. During the seventies, computing power in¬creased and applications expanded from two-dimensional problems to three-dimensional modeling. Moving into the eighties, as computer hardware costs will significantly decrease, the major expense of computing will be the manpower required to develop, implement, and use an application; therefore, improved programming techniques and applications software engineering methods will be used to optimize and preserve this investment. This chapter presents a general overview of computer methods in geophysical reconnaissance; it is divided into two parts: geophysical methodology and software engineering.

Jan 1, 1979

By Michael H. Leon, John A. Organiscak

Controlling worker dust exposure on longwall mining systems is difficult because the working face area serves as an immediate return during the mining cycle and the amount of airborne dust generated is directly related to production. Since improvements in longwall mining technology have significantly boosted production levels, additional technology is needed to control the airborne respirable dust generated at present and future production levels. One concept to reduce longwall worker's dust exposure is to maintain two splits of air at the face -- a clean intake split in the workers walkway, and a return (dusty) split over the face conveyor. The U. S. Bureau of Mines has recently investigated a concept to overcome the visibility handicap of face partitions by utilizing a permeable polyester mesh. The mesh material was anticipated to provide adequate air-splitting capabilities as long as the pressure differential between the face and worker walkway was minimal. Initial testing of this concept at the Bureau's Lake Lynn Laboratory showed that notable reductions could be achieved with a 1/8 in (3.18 mm) and 1/16 in (1.59 mm) mesh opening size. Dust reductions at 100 ft (30.5 m) and 200 ft (61.0 m) downstream of source were 58 and 36 pct, respectively, for the 1/8 in mesh and 79 and 55 pct, respectively for the 1/16 in mesh. Longwall application of the 1/8 in mesh showed similar results to the Lake Lynn Laboratory tests. A flame retardant mesh was used underground with portable lighting mounted on the shearing machine for face side lighting.

Jan 1, 1993

By S. Komar Kawatra, Henry J. Walqui, Timothy C. Eisele

Population balance models were used to model the grinding action of industrial scale coal pulverizers. Experimental work was conducted with two different coal samples to determine the values of the appearance and selection function. These functions were determined for vertical mills by using s 6-inch by 10-inch laboratory roll mill to represent the action of a vertical mill. Two very important operating variables were identified for vertical mills: feed rate and roll spacing. Factorially designed experiments were used to analyze .and quantify the effect of these two variables. The models were then adapted to represent changes in operating conditions by incorporating the effect of the feed rate and roll spacing effects. This resulted in a simulation model able to respond to changes in operating conditions, by providing corrected predicted values for the product size distribution.

Jan 1, 2002

By K. Tokutake

Kobe Steel, Ltd. improved the quality of iron ore pellets for blast furnace burdens when it enlarged its blast furnaces. However. there still remained room to increase reducibility at high temperatures for better blast furnace operation. In particular, it was still necessary to lessen the reduction retardation above 1200?C. In the last few years, by employing iron ore and additives of optimum size structure, large pore pellets with a high porosity have been obtained. By using this method. Kobe Steel. Ltd. has accomplished the technology to produce pellets with remarkably high reducibility.

Jan 1, 1989

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By Alfred Petrick, Roger Dewey

INTRODUCTION Estimation of capital and operating costs for mines and mills has long been a necessary ingredient of feasibility studies, and though many practitioners have successfully used "rules of thumb" and factor estimating methods for many years, a great deal of work is usually required to prepare an initial estimate and/or to update or revise such an estimate. Development of comprehensive mining and milling cost models during the 1970's by the U.S. Bureau of Mines and by Canadian workers (O'Hara and Mullar) provided the basis for feasibility-level cost estimates, but the numerous equations and the apparent rigor and complexity involved in preparing a project estimate using these models has discouraged many, if not most, potential users. Their acceptance was also hindered by a broad misunderstanding by many engineers in the minerals industries who had little exposure to such procedures, and by a possibly inadequate level of explanation or documentation of the parametric approach to cost estimating. The preliminary nature of most databases, geologic/engineering/ and market, available to the engineer or analyst during the early stages of a mineral project is a universal problem. Basing corporate mega-investment decisions or even individual equipment selection decisions on the usual "SWAG’s has always been a risky practice, but in the current business environment, the "guesstimates" are almost 'verboten', and are certainly becoming antiquated with the advent of both the described models, the ubiquitous microcomputer, and the nearly-ubiquitous hybrid species known as the "computerized engineer". Engineers have almost always sought techniques of cost estimation that can be applied and justified when geologic and engineering information for a mining project is preliminary and incomplete. The answer, in some cases, is the "parametric" approach. Equations, based on actual, past experience are developed to relate capital and operating costs to major physical variables such as the rate of mining or milling, with modifiers for such details as mining method, process characteristics, methods of construction, or types of equipment . Cost Engineering Standards Five major types of fixed capital cost estimates have been defined by the American Association of Cost Engineers : 1. Order-of-Magnitude estimate based on previous cost data and minimal knowledge. usually a "ratio estimate" with no better than +/- 30% accuracy. 2. Factored or ratio estimate based on major equipment costs with probable accuracy in the 25 to 30% range. 3. Budget authorization or Preliminary estimate, based on sufficient project data to

Jan 1, 1987

By M. N. Brodie

The paper examines the requirements for electric power used in concentration and dewatering circuits, the effects of plant capacity and process type, the restraints imposed by the primary supply and applicable codes and outlines the procedure by which effective design is carried out.

Jan 1, 1986

By John Turney, John Gathje, Donald Gale

The Eskay Creek deposit, located in northern British Columbia, is a high-grade gold/silver ore associated with complex polymetallic sulfides. Process development began in 1989 and continued through 1993. Because of the refractory nature of the ore, options including roasting and smelting were investigated. The selected process of pressure oxidation was the basis for basic engineering design until a re-evaluation of economics and risk indicated a preference for toll smelting. Although well proven in many industrial applications, pressure oxidation of the Eskay Creek ore dictated several innovations to solve problems associated with silver jarosite formation, preg-robbing, and high soluble copper and zinc concentrations.

Jan 1, 1995

By W. M. Jr. Aubrey, R. L. Stone

INTRODUCTION Most metallic minerals and some industrial minerals have a relatively high specific gravity and most have at one time or another been concentrated by gravity methods. The principles of gravity concentration are straightforward, well documented and easy to understand, but in practice there are many pitfalls that await the engineer in the development of an integrated flowsheet. Gravity concentration equipment has a long history of use and there is a great diversity available. The equipment is capable of treating material over a broad size range, only falling off in efficiency in the very fine sizes. Gravity concentration is also inexpensive, generally free of environmental problems, and commercial equipment can process large tonnages of ore with a minimum of capital cost. As might be expected of an efficient and low cost process, the bulk of the tonnage quickly and inexpensively. Another obvious application is treating mineral deposits such as hematite and manganese ores that are sufficiently liberated after a minimum of crushing to allow production of a coarse concentrate that will meet market specifications. Except for hand picking and mechanical sorting, there is no competing process on coarse size material. Conversely, it is sometimes obvious that gravity concentration does not warrant consideration. Examples are ores that require very fine grinding to attain liberation, for ores where the minerals of interest have a gravity similar to the gangue, and ores that are strongly magnetic. Actually a mineral processing engineer may not know if gravity is the best way to concentrate an ore, but he should have little difficulty recognizing when gravity concentration deserves consideration based upon specific gravity differences and liberation gravity concentration has wide use. size. His challenge then is to At times its selection as the identify and test the applicable primary concentration process is processes, to develop a obvious. Low grade placer deposits metallurgical balance and flowsheet of tin, gold and beach sands usually for the best process, to estimate are only profitable because gravity production rate over the life of concentration is able to throw away the deposit and to make equipment

Jan 1, 1986