Search Documents

By Jean-Marie Deschamps

In an approach to the complicated study of bauxite from Les Baux de Provence it is necessary to consider the paleogeographical context of all the bauxites in southern France. These bauxites are of Karstic type, belonging to a metallogenic area extending from the Pyrenees Mountains to the Alpine Massif. Within this area each deposit does not always correspond to the same geological period. There are differing opinions regarding the origin of Karstic-type bauxite and a discussion of these various theories is beyond the scope of this paper. Bauxite of Les Baux, in Provence, was discovered in 1821 by the chemist, Berthier, near this picturesque village located in the region of Arles. It is Les Baux from which the name of bauxite originates. For a long time this bauxite was of no interest because of high silica 'and mediocre alumina content. Besides, the calcium carbonate content is somewhat high and is one of the main characteristics of Les Baux bauxite. The problem of exploration of the Les Baux deposit has been to prospect minable zones according to traditional norms where silica and carbonate are low.

Jan 1, 1977

By Ulrich Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 kilometers north of Atlanta, Georgia. The project consists of: a 28-meter high dam, a 90-centimeter diameter outlet conduit; an emergency spillway; and a 4.0-meter diameter hard rock trans-basin diversion tunnel. This floodwater management system was part of Cities Service Company mine safety program for the Cherokee orebody which is partially located within the stream channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1978

By R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in Carbon in Pulp and Carbon in Leach circuits has been investigated. Carbons from four U.S.A. mines, one Canadian mine and one South African mine were characterized before and after regeneration. The use of thermal gravimetric analyses demonstrated the presence of inorganic compounds on the surface of the carbon. Thermal regeneration was investigated using factorial' analysis to determine the effect or interaction of furnace temperature, retention time and the use of supplemental steam. The operation of acid leaching prior to or after gold elution was investigated. The effect of water quenching, regenerated carbon was also studied. From the data obtained in this investigation, guidelines are given for effective regeneration operation.

Jan 1, 1985

By H. V. Alminas

The U.S. Virgin Islands consist of three major islands (St. Thomas, St. John, and St. Croix) and some 50 smaller islands that are located primarily along the coasts of St. Thomas and St. John. St. Croix, the largest of the islands, is located approximately 160 km south-southeast of San Juan, Puerto Rico and is about 218 km in area (Fig. 1). St. Thomas, the second largest island is located 64 km east of Puerto Rico and incorporates approximately 77 km2. St. John is located immediately to the east of St. Thomas and incorporates approximately 49 km2. The climate in the U.S. Virgin Islands is maritime tropical. The average annual rainfall at higher elevations is 127-152 cm and at lower elevations 51-76 cm. There is no well-defined wet or dry season. Temperatures generally average in the 80's (F°) with only a 5°-7° F variation throughout the year.

Jan 1, 1987

By Jagannath Pal, Ammasi Ayyandurai

Hematite ore pellets require a much higher induration temperature than magnetite ore pellets because no exothermic heat is generated due to oxidation inside during induration-like magnetite pellets. Carbon is used as in situ heat source in hematite ore pellets which can reduce temperature requirement in the induration strand and hence decreases energy consumption. Many investigators have reported that a 0.8–1.25% addition of carbon in hematite pellets can improve the pellet properties also. However, to investigate the exact role of carbon in hematite pellets, its reaction mechanisms and kinetics study are required which have not been done so far. Therefore, the reaction mechanism and its kinetics have been studied in this investigation. It has been found that carbon reaction happens in pellets from the surface towards the center in a topochemical manner which is controlled by pore diffusion of gas, and its activation energy is around 52 k J mol− 1. It is also found that apart from in situ heat, carbon in hematite pellets enhances diffusion bonding which improves pellet properties. This study ascertains the exact role of carbon in hematite pellets which may help operators to use carbon effectively to reduce energy consumption and improve pellet properties.

Nov 6, 2022

By John F. Abel

Convergence measurement across the 17.4 m (57ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 by 9.6 m (38 by 31 1/2 ft) I.D. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2 3/4 in.) and 5.7 cm (2 1/4 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1984

By Jeffery Leavy, Ken Davis, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) is a United States Department of Energy facility located in southeastern New Mexico. It is designed for the safe disposal of transuranic radioactive waste in deep geologic salt beds. Westinghouse TRU Solutions, LLC, the managing and operating contractor, undertook a project to simulate the processes at WIPP in order to identify bottlenecks and optimize available resources. The activities simulated in the model included the receipt, processing and disposal of radioactive waste underground, the mining of new areas for future waste disposal and the transportation of salt out of the mine. The complexity of the processes and the interactive requirements between processes required the use of advanced modeling techniques. The simulation model includes a huge number of locations and path network node points, with movement to and from the locations controlled using parameters rather than explicit routing. Information for the timing and sequence of the mining and nuclear waste emplacement operations is brought into the model via spreadsheets. Arrays in the simulation model keep track of past and future events that occur. Routing to the multiple possible positions in the underground mine is done using attributes, and system functions within ProModel in order to allow for a highly flexible sequence of planned events and to reduce the level of effort in creating the ProModel processing. Considerable use of subroutines in the simulation model is utilized for parametric decision-making that is repetitive. This presentation describes the modeling techniques used to accurately simulate the surface and underground operations. The surface and underground operations are considerably different, thus they will be treated in their own sections.

Jan 1, 2002

By K. Zhang

Real option value (ROV) method is considered to be more practical and advanced compared to net present value (NPV) method in evaluating a mining project, in particularly when there is substantial uncertainty in the commodity market as well as possible operational flexibility embedded in the project. Usually, it may take months or even years for the commodity product to be available in the market after the mining activation decision is made. The impacts of postponing the delivery of commodity product on the mine?s ROV and NPV are assessed based on the proposed real option method. Postponing the delivery of the products leads to declined NPV and ROV compared to the non-postponing scenario and extended postpone results in higher lost values in NPV and ROV. For a mine with lower mining cost, by postponing the delivery, the exercising threshold of commodity price is lower because the mine owner anticipates that commodity price may rise during the time of postponing. A mine with higher mining cost requires a higher exercising price threshold to ?lock up? the profit when there is ambiguity of market situation due to the postponing of the delivery.

Feb 23, 2014

Innovative mining technology came to Texas in the form of bucket wheel excavator/cross-pit spreader systems. Texas Utilities Mining Company put the first system to work at its Big Brown Mine in December 1985. The second such system was put into operation at the Monticello Mine in February 1991. The cross-pit spreader systems are mobile, electrically powered, excavation and conveyor systems, the principal components of which include bucket wheel excavators (BVE) and an across-the-pit conveyor (spreader). These crawler mounted machines operate as a unit; the BVE's excavate overburden, feed it via conveyors to the spreader which in turn conveys the material across the open pit and onto the developing spoil bank. The system at the Big Brown Mine is composed of 2 BVE's and an across-the-pit conveyor while the Monticello system is made up of 1 BVE and a spreader. The BVE's prestrip overburden preparing a dragline bench for the final removal of overburden. Numerous evaluations, including lignite production requirements, economics, overburden characteristics, rehandle reduction, spoil stability, and the compatibility with dragline operations, led to the selection of the cross-pit spreader system at the Big Brown Mine. The system has proven itself as a viable and economical means of prestripping. The system's success at the Big Brown Mine led to the development of a second such system at Monticello. The advent of the cross-pit spreader system is viewed by Texas Utilities Mining Company as a viable solution to recovering deeper lignite reserves in a safe and economical manner.

Jan 1, 1993

By Meng Wang

"In this study, multiple methods that include geological surveying, laboratory studies, and numerical modeling have been used to study the deformation characteristics of a “deep inclined rock roadway with weak planes” (DIRRWP). Failure of the DIRRWP was found to be triggered initially by the shearing of the rock near the weak plane. The movement of the failed rock resulted in reduced confinement of the deeper rocks, and causing the failure of the supporting units and the severe deformation of the surrounding rocks. Hence, it is concluded that DIRRWP stability is affected predominantly by rocks near the weak plane. Corresponding control strategies for DIRRWP deformation were proposed: (1) greater support intensity is necessary to maintain the stability of the whole DIRRWP; (2) additional support is needed for rocks near the weak plane to reduce the potential of failure; (3) to increase the bearing capacity of the floor strata, as the floor needs to be supported; and (4) a supplementary support technique should be considered for cases of large deformation. The case study presented here indicates that the proposed control strategies can significantly reduce the potential of failure in rocks near the weak plane, thus preventing severe deformation of the DIRRWP.INTRODUCTIONAs shallow seams are mined out, the cover depths in most Chinese coalmines have become increasingly greater. Deep cover in a coalmine is considered to occur when the cover depth exceeds 800 m (Sun, Chen, and Miao, 2018). The loading and failure behavior of rocks in a deep cover setting are quite different from those in a shallow cover setting owing to the increase in in-situ stress, temperature, and hyperosmosis (Lobanova, 2008; Zhang et al., 2013). For instance, experience shows that bulking and dilating deformation in deep roadways is much greater than that which occurs in shallow roadways (Hou and Yang, 2018; Zhang et al., 2016). In addition, anisotropic behavior and thickness deviation of coal measure rocks, combined with the appearance of weak planes (e.g., faults, joints, and coal cleats) in coal and/or rocks, can significantly affect the stability of an underground roadway (Ghazvinian et al., 2013; Sun, Chen, and Miao, 2018). The presence of weak planes can significantly complicate displacement and stress transmission in nearby rocks. Additionally, tensile, compressive, and/or shearing failure in rocks near weak planes can be easily caused by high in-situ stresses in deep roadways; such failures may lead to further severe deformation of the surrounding rocks, resulting in roof falls and rib spalling (Kamata and Mashimo 2001; Wu, Ohnishi, and Nishiyama, 2004). A typical failure of the so-called “deep inclined rock roadway with weak planes” (DIRRWP) is shown in Figure 1. Severe deformation can be found near the weak plane. In this study, a plane or thin layer of rock/coal parting that can significantly reduce the strength of the surrounding rocks—and thus affect roadway stability—is defined as the weak plane."

Jan 1, 2019

By Heriban Soto

Primary amines are strong collectors of apatites and they can selectively float sedimentary phosphates from calcareous ores. However, secondary and tertiary amines and tri-methyl ammonium salts were ineffective. The use of kerosene reduces the collector requirements because hydrocarbon is coadsorbed along with the amine on the mineral surface. The heats of reaction of aminium ions with such anions as phosphate, carbonate and sulfate, were measured in a microcalorimeter and discussed in terms of the solubility of the precipitates formed and their relationship with the adsorption mechanism of primary amines on phosphate minerals. Experimental evidence supports a view that primary amines are adsorbed through chemical interaction between the aminium and phosphate ions at the mineral surface.

Jan 1, 1984

By Clifford W. Schultz

Four native copper ores, two conglomerate and two amygdaloidal, were tested to determine their amenability to sorting. One of them, a conglomerate ore from the Kingston mine, showed a high sortability as evidenced by an 80 pct recovery of copper in the minus 6-, plus 1/2-inch size range. Using the Kingston as a case example, the cost of mining and concentrating was estimated for a standard case and five optional cases involving varying degrees of sorting. This analysis indi¬cates that the production cost per pound of copper can be reduced on the order of 1 to 1-1/2 cents per pound along with a significant decrease in capital investment.

Jan 1, 1975

By Dennis R. Twining

Recently a mining analyst for a major bank called me to say that during his travels he had encountered an electric utility interested in a new uranium supply. Since we produce uranium as a by-product of phosphate operations rather than as a primary product, he assumed we simply sold our output in the spot market and that a new prospective purchaser would be of interest to us. This assumption was incorrect; the uranium had already been sold on a long term basis at terms more favorable than the currently depressed spot market. From the outset our approach to the marketing of uranium was based on the principle that by-product marketing is not unlike primary product marketing. This was particularly appropriate in the case of uranium, as we were planning a considerable technical and capital commitment to a new business. This illustrates: that the fundamental principle in by-product marketing is to follow a primary product strategy; that the terms "by-product" or "co-product" are creations of accountants; that they have no place in marketing decisions! Traditionally, the term "by-product" has implied that only a secondary marketing effort is required. Recent history has contradicted that view by demonstrating that by-product values can have marked impact on a mine's revenues and costs. In fact, by-product values can spell the difference between success and failure.

Jan 1, 1983

By Remi Tremblay

This paper describes the laboratory study which permitted an exploration of high grinding ball consumption in the secondary open circuit wet grinding mills at the Sidbec-Normines plant, Port Cartier, Québec. Corrosion undoubtedly exists but is of minor importance. Abrasion resulting from the physical nature of the company's iron concentrate is the main reason for the high ball wear. It was found that at least 30% reduction in ball consumption is possible by decreasing attrition grinding through the use of lifters in the mill. At the industrial level this would entail more lifters and/or higher lifters in the mill linings.

Jan 1, 1984

By Dean E. Albon

In the late 1940's and early 50's in southern Illinois, the usual open pit blasting in the coal field consisted of one or two rows of churn drilled vertical holes being shot with instant electric blasting caps. The entire shot detonated at one rime. In southern Indiana and Ohio most mines were drilling horizontal holes and they too were primed with instant EB caps. During the ten years from 1355 through 1965 many changes occurred in drilling and blasting methods. The churn drill in southern Illinois and the horizontal drill in Indiana and Ohio were replaced by the rotary vertical drill. The ammonia dynamites and liquid oxygen explosives were replaced by ANFO. The elctric blasting cap in the hole was replaced by a detonating cord down line and detonating cord trunk lines made the connections between holes and rows of holes. Host open pit mining was in areas far enough from town that the noise and vibration from blasting was, if not ignored, at least tolerated. During the 1960's open pit mining expanded to account for nearly 50% of the coal produced. Mines came closer to town and towns expanded along the highways with suburban homes and mobile homes. The mines began receiving complaints about the noise and vibrations from blasting operations.

Jan 1, 1976

By H. T. Mikkelsen

Mineral production implies emissions of particulate matter (dust), noise and vibration that may cause conflicts with neighbors living nearby. In Norway a few conflicts has been brought to court, the latest in 2006. This paper discusses dust emissions and dust depositions (dustfall). The pollution authorities have accepted monitoring of dustfall instead of suspended dust as the first step in conflict cases concerning small and medium sized enterprises. In the case of exceeded limit values, the second step is to require monitoring of suspended dust and next the implementation of control actions to reduce dust emissions. Dustfall monitoring programmes carried out at six mineral production plants in Norway, show that the mineralogical rates of dustfall are rather low a few hundred meters away from the plants or the tailings disposal. They are mostly considerable lower than the limit value of 5 g/m²/30days accepted by the authorities. Seasonal variations between mineralogical and organic dust fractions can be observed in Norway, with higher content of mineral dust during winter time. Other sources to mineralogical dust can be recognized. During winter time wear of road pavement and sand on icy roads can give high emissions of mineralogical dust to the ambient air. Parallel monitoring of suspended dust and rates of dustfall indicate that dustfall can be used to estimate the level of suspended dust. A model for estimating suspended dust based on records of dustfall is presented.

Jan 1, 2007

By M. G. Ayat

Coal degradation is the breakage of coal particles to finer sizes due to the continuous forces of attrition and gravity to which coal is subjected during mining, handling and preparation. The objective of this paper is to determine the extent of degradation that a coal slurry experiences when transported through pumps and pipelines. The examination of degradation results for a number of different coal slurries have indicated that the extent of breakage is dependent upon the physical properties of coal and the time span of circulation. These results have also indicated that certain size fractions of coal are more susceptible to breakage than others.

Jan 1, 1986

By Jasper D. Ward

The Indiana Limestone Company has developed an insulated, thin and comparatively light-weight pane 1 suitable for use as a spandrel panel in a curtain wall. The panel is about four inches thick and is composed of limestone backed with insulation. The inner surface of the insulation is protected with asbestos-cement board or a metal pan, depending on the type of insulation, building-code requirements and appearance (if the surface is left exposed). The limestone is cut to the size of the spandrel openings and the insulation and backup is applied in the mill ready to be shipped and in- stalled in the wall grid, A mortarless and waterproof joint with the metal frame components is achieved through the use of neoprene, thiokol, and caulking, The limestone is "dirt-proofed" (waterproofed) in the mill to slow down discoloration. The panel weighs more than some presently used materials. However, ILCO's architects and engineers have found that curtain wall systems capable of withstanding imposed wind loads are made up of sections large enough to carry this extra load of stone with little or no modification to the size of the metal frame. Limestone, a traditionally sound material, can be used in this new way without losing any of its natural qualities of dimensional stability, resistance to fire, and permanence.

Jan 1, 1959

By E. De Souza

Rockbursts and rockfalls cause very large safety and productivity losses in underground mines. One of the major unsolved problems of safe, economical rock support in underground mining has been that of maintaining anchorage during dynamic rock loading conditions or seismic related occurrences. It is recognized that the large displacements and high strain rates in excavation walls and underground structures cannot be countered by increasing the strength of stiff rock-reinforcing systems but must be accommodated by introducing yieldability into the support elements. This paper introduces a low cost yieldable support system which provides viable solutions to dynamic support loading. Such system should not only provide a feasible and more effective rock mass stabilization strategy but improve mine safety and reduce losses.

Jan 1, 1998

By J. A. Barrera-Godinez

Traditional batch flotation tests produce a limited number of data points from which to evaluate the kinetics of the process. In this research, continuous weighing of froth, from a modified circular flotation cell, using a computer/data acquisition system., has been coupled with chemical analyses from intermittent froth sampling. This combination has permitted the experimental data to be smoothed such that the flotation kinetic parameters could be determined with enhanced confidence. To demonstrate the procedure, a galena ore was floated to permit flotation kinetics to be investigated as a function of cell parameters. It was shown that the kinetic data of this lead flotation most closely correlated with the Huber-Panu three parameter model. In addition the results illustrated the effect of froth thickness, froth scraper rate and air flow rate on the cell performance, in terms of mass flow, grade and recovery.

Jan 1, 1990