Search Documents

By A. Pomianowski

A spectrophotometric study of xanthate solutions alone and their mixtures with equimolar amounts of alkyl trimethyl ammonium bromide (CnTAB) has established the additivity of ultraviolet spectra (190 - 400 my) for potassium ethyl xanthate (KEtX) and C12TAB. No obvious effect of C12TAB addition on the decomposition rate of KEtX was observed. The kinetics of collector abstraction by copper, nickel and sphalerite powders were studied in 10-5 - 10-3M solutions of KEtX alone and in equimolar mixtures of KEtX and C12TAB. Presence of C12TAB caused a 2 - 3 fold increase in the amounts of xanthate (equivalent to many monolayers) abstracted by copper and, nickel powders but had no effect on the abstraction of xanthate by unactivated sphalerite. The adsorption of C12TAB itself from the mixed solutions was very low, at most ore monolayer only, and was not influenced by the nature of the solid powder used. The results are interpreted in terms of molecular associations and synergistic action of xanthates and quaternary amines.

Jan 1, 1963

By R. Gorakhki, R. Stafford, A. Jung

Geosynthetic clay liners (GCLs) have been used widely as an alternative for compacted clay liners and covers in mine waste applications. The high swelling of bentonite particles in the GCL creates a uniform barrier layer that results in low permeability of water and mine waste leachate. GCLs must provide sufficient internal and interface shear strength stability, especially if GCLs are used in steep slopes under high normal loads. Peel strength is a common parameter that is typically correlated to internal shear strength properties of GCLs. The relationship between internal shear strength and peel strength of GCL at normal stresses of 287, 575, 862, and 1724 kPa is evaluated in this study. The data in this study was compared with the peel strength-internal shear strength relationships found in literature. The study concludes that the relationship between peel strength and internal shear strength is unique based on manufacturing, needle-punching density and the method with and without heat treatment of the geotextile end fiber bundles.

Feb 1, 2023

By A. R. Laplante

A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; an error analysis is detailed; possible uses are discussed. Of the 38 samples tested, the lowest GRG content was found to be 25% (most below 25 11m, or 600 mesh), and the highest 94% (most above 300 11m, or 50 mesh). The average GRG content was 63%, with a standard deviation of 19%. Error analysis shows the test to be reproducible within 5 to 10%, depending on the size distribution and grade of GRG, and the sample extraction protocol. When using the same primary sample, reproducibility improves, 2 to 5%, depending on the amount of gold coarser than 850 11m (20 mesh) and sample weight. The test has been applied to greenfield project and retrofit applications, to determine the suitability of gravity recovery. For existing circuits, it has been coupled with a model of gravity recovery for optimization studies.

Jan 1, 1996

By S. K. Mishra

The history of the Australian coal industry is almost as old as the history of Australia after new settlement. The first cargo of coal was exported from Newcastle to India in 1799. Although coal has been mined in Australia for almost two centuries, there are indications that the first coal was processed in 1877 in the New-castle area, nearly a half-century after the first coal processing in Europe. Processing on any significant scale began only in 1944 at the Newcastle Steel Works. In Queensland, however, coal processing did not begin until the second quarter of this century. The well-known dramatic growth of mining and processing of Australian coal since the mid-sixties has primarily been due to the expansion of the export market in Japan and other Asian and European countries. Black coal occurs in most of the major sedimentary basins in Australia. The better known deposits of commercial importance are in Sydney, Bowen, Oakland and Gailiee Basins (Figure 1). Apart from Collie Basin in Western Australia, other coal deposits of the Arckinga Basin in South Australia, the Bonaparte Basin in Northern Territory and Tasmania Basin, Tasmania, are basically unexploited. Sydney Basin of New South Wales and Bowen Basin of Queensland remain the major producers of black coal in Australia.

Jan 1, 1985

By S. Komar Kawatra, J. J. Carlson

"It is widely known that steel made from iron ore pellets high in phosphorus is brittle. Removal of phosphorus from iron ores such as hematite has proven to be difficult. The majority of research on phosphorus removal from hematite ores has been focused on flotation. The purpose of this study was to assess phosphorus distribution under current operations at an existing hematite concentrator and determine how efficient the plant is at removing phosphorus. Objectives included: (1) Perform a phosphorus balance at an operating plant to assess phosphorus distribution under current operations; (2) Determine phosphorus removal efficiency of each separating unit and (3) Perform a quantitative liberation analysis to determine max phosphorus removal by physical means. Liberation was quantitatively determined using wet high intensity magnetic separation (WHIMS) to separate iron ore from liberated apatite (and other nonmagnetic compounds).It was observed that 61.2% of the total phosphorus entering Plant F was rejected during current operations. The desliming process was the most efficient step at removing phosphorus (45.1% P removed), whereas the flotation step was much less effective (16.1% P removed). Liberation analyses indicated that the deslime thickener may have been more efficient at removing phosphorus than the flotation circuit due to the greater abundance of liberated phosphorus in the deslime thickener feed. The scavenger returns stream was identified as having a high concentration of phosphorus and a possible point of phosphorus removal. However, liberation analyses indicated that only 32.4% of the total phosphorus in the stream was liberated. Grinding the scavenger returns to 80% passing 5.2 µm increased the amount of liberated phosphorus in the stream to 70.4%."

Jan 1, 2014

By E. Fidler

A recent headline in the Wall Street Journal declared, "trendy management schemes very often fail." Many of the management techniques addressed in the accompanying article are associated with quality management including reengineering, benchmarking, total quality management, and employee empowerment. The article made the point that executives, employees, and customers who are involved in such programs rate the effectiveness of these programs very low, and the programs often fail. Yet, we all know of companies that have made significant advances in their operations using these same quality management practices. Why do a few succeed while many fail? History has shown that the companies that successfully carry out quality management programs have two things in common: 1) Strong leadership committed to the success of the program. 2) A comprehensive plan for carrying out and maintaining the program. Stated another way -the reason many companies fail is the lack of committed leaders and inadequate planning. It is ironic that the title of the Wall Street Journal article is "The Best Laid Plans."

Jan 1, 1994

By T. D. Wheelock

The effect of various flotation depressants and surface treatments on the floatability of coal derived pyrites in the presence of XIBC was investigated with a modified Hallimond tube microflotation cell. The floatability of pyrite particles which had been cleaned with hot dilute (5%) hydrochloric acid was relatively large. However, the floatability of such particles was reduced greatly by the addition of specific depressants such as calcium hydroxide and also by treating the pyrite with an aerated warm alkaline solution. Although this treatment and these depressants also had some effect on the floatability of coal particles, the effect was much less than on the pyrite particles.

Jan 1, 1979

By C. J. Konya, A. Konya

"Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industry, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, the optimization of explosive load, as well as prediction methods for the environmental affects for the technique of Precision Presplitting. BACKGROUND Methods of controlled blasting in which a smooth, stable wall could be blasted have been an important consideration since blasting in mining and construction has begun. How can one use an explosive, with its massive energy and power, to break a non-homogenous rock without causing backbreak, poor walls, or deviations in the wall over large distances? The blasting industry has known for a long time that blasting ‘high benches’ would result in better walls and less backbreak. However, this was not a sufficiently controlled technique for critical projects, such as the Niagara Power Plant. This was one of the main challenges Hercules Powder faced when they began the project. In order to achieve this, they used a new tool in the explosive engineer’s toolkit, presplitting. The presplitting done on the Niagara Power Project utilized 1 ½” x 8” (38mm x 203mm) 40% gelatin dynamite in 2 ½” (63.5) diameter boreholes. This was done on multiple levels with benches between 12 feet to 52 feet (3.6m to 15.8m) with a total powder factor of 0.75 pounds/cubic yard (0.45 kg/m3). The spacing on these holes ranged between 18 inches to 24 inches (0.46m to 0.61m), center to center (Langfors & Kihlstrom, 1973). The strange aspect of this project was that this “lightly loaded” closely spaced row was fired before the production blast, yet this project produced some of the best walls seen at that time directly from blasting. In today’s blasting industry, presplitting is a more common way to produce smooth, stable high-walls for both the construction and the mining industry. Today, explosive loads for traditional presplitting is generally measured in pounds per foot (kilograms per meter) and typically ranges from 0.30 lb. /ft. to 0.5 lb. /ft. (0.45 kg/m to 0.75 kg/m). MECHANICS OF PRESPLITTING When analyzing a blasting process like the Niagara Project, many wonder how did that work when normally confining a charge would cause cratering and increased backbreak. Since then, presplitting mechanics have been studied extensively. It has been shown in many models that presplitting is not achieve through the collision of shockwave, but by gas pressure in the boreholes. In addition to models and finite element simulations, this has been proven full scale using Pyrodex, a propellant, to create a presplit plane with no shock wave present (Konya, Dean Barrett, & Smith Jr, Presplitting Granite Using Pyrodex, A Propellant, 1986)."

Jan 1, 2017

By Carlos Álvarez, Sergio Sánchez, Michael Mains, Giuseppe Gaspari

Extensive record of tunnels excavated with SEM (sequential excavation method) in swelling grounds exists in literature: global experiences include successful tunnelling both through clayey and rock masses with time dependant deformation. However, TBM (tunnel boring machine) use in swelling conditions with high water pressures (EPB, earth pressure balance, machines or slurry shields) is much less documented, considering the lower expected impact due to the limited stress relief and operations under saturated conditions. This paper summarizes a number of studies conducted as part of the risk assessment and detailed design of a large diameter TBM tunnel in variable and challenging geological conditions. The tunnel alignment is driven through mixed face conditions including swelling soils and clayey soft rocks, prone to intense time-dependent deformations. The paper also describes the approach adopted for the design of pre-cast segmental lining subject to both swelling actions and high seismic loads, due to the regional active tectonic faults. The design of this lining included a detailed parametric study performed to handle the existing uncertainties related with ground characterization, potential deconnement and complex geological congurations.

Jun 23, 2024

By Y. Akin, M. Hancer, M. S. Celik, J. D. Miller

Flotation pulps with boron minerals such as colemanite and borax using primary amine collectors, e.g. dodecylamine, exhibit collector precipitation above a critical pH depending on the amine concentration. This was earlier attributed to the formation of a mine hydroborate. However, results from this current study indicate that the precipitate is dode-cylamine, rather than dodecylamine hydroborate. A systematic study involving solubility, zeta potential, microflotation, adsorption, and surface tension measurements is presented to elucidate the role of a mine precipitates in boron flotation systems.

Jan 1, 2000

By Peter G. Zambas

In planning an underground room and pillar mine, the selection of the shaft or portal location and the orientation of the main haulage arteries is of paramount importance, particularly in view of the high dependence of the cost of truck haulage on the proper definition of these parameters. In an effort to facilitate this selection a computer program was written which, by relating the truck characteristics to the areal configuration of the property or ore-body, derives the volume-weighted total fuel and time requirements for hauling ore from every panel within the property to a specified portal or shaft location through a predetermined gridwork of haulage drifts. By varying the size and orientation of the gridwork and the location of the portal or shaft access, an infinite number of configurations can be investigated. The results of this analysis can be plotted to indicate the optimum conditions.

Jan 1, 1971

By Charles Kimbell, L. Nahai, E. Shekarchi

INTRODUCTION AND SUMMARY World mineral trade during 1960 to 1984 has shown substantial changes both in value and tonnage. Although fuel commodities dominated total mineral trade during this period, this paper will focus attention primarily on nonfuel minerals. Brazil and Australia, modest producers of iron ore in 1960, have become dominant producers and exporters, together accounting for about half of major iron ore exports in 1984, far surpassing traditional export suppliers such as Sweden. Australia has also become the largest producer and trader of bauxite and alumina, and worldwide alumina trade has increased at the expense of bauxite trade. Similarly, shipments of ferroalloys have increased more than shipments of ores such as those of chromium and manganese. Canada, retaining its first rank in world export of zinc, has become also the leading source of potash and sulfur in world trade, and South Africa has been the dominant factor in chromite, manganese and their respective ferroalloys. Developing countries' share of world copper trade has increased, with Chile maintaining first rank, but developed industrialized countries have continued to dominate production and trade of lead and zinc. Phosphate, sulfur, and potash have been the principal crude nonmetallic minerals traded worldwide. Looking to the near future, dramatic increases in export of iron ore, phosphate, potash and sulfur are not envisaged. Bauxite exports will continue to decline relative to alumina but at a slower rate than in the recent past. Zinc concentrate will continue to be exported but lead will be traded more as metal than as concentrate. For iron and steel, there will be some production shift from traditional producers to certain developing countries and recently industrializing developing countries such as Brazil, India, the Republic of Korea, and Taiwan. In the following sections dealing with specific commodities, it should be understood that information is presented only on the major forms of each commodity that move in trade, and only for a selected group of countries for each commodity or major form of each commodity. Thus, totals shown or mentioned generally represent only the totals of figures presented here and do not include estimates for minor forms of material or for countries that are not listed. However, the data provided is regarded as sufficiently complete to reflect major patterns and trends, and exclusions are there- fore not seen as affecting conclusions that may be drawn from the material provided. FUEL AND NONFUEL TRADE Values of Fuel and Nonfuel Trade The value of world export trade in major mineral commodities (ores, concentrates and scrap, crude minerals, iron and steel, nonferrous metals, nonmetallic minerals and mineral fuels) in 1983, the latest year for which comprehensive data are available, was reported by the United Nations in May 1985 to have totaled over 514 billion current U.S. dollars (Table 1). This was 79% of the historic record high of nearly $649 billion ,current dollars set in 1980, but almost 18 times the current dollar value reported for 1960. [1/] The value of these 1983 exports in constant 1960 dollars was $164 billion (Table 2), only 66% of the record 1980 high of almost $250 billion, and only about 5.7 times the 1960 dollar level.

Jan 1, 1986

By Patrick Shea

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management, U.S. Forest Service and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the National Park Service, U.S. Forest Service and Bureau of Land Management. The U.S. Department of the Interior has worked with the U.S. Geological Survey, the U.S. Forest Service, the U.S. Environmental Protection Agency, and western state governments to identify and prioritize these sites on Bureau of Land Management, National Park Service and U.S. Forest Service administered lands. This presentation will discuss the accomplishments we have made to date to clean up inactive and abandoned mine sites, focusing primarily on lands administered by the Bureau of Land Management.

Jan 1, 2000

By J. R. Hunter

The present is rooted in the past. This is particularly true in the case of mining operations. Coal mining in the United Kingdom is considered an old Industry comprising today 246 Coal Mines many of which have worked coal reserves in their locality for over 100 years. More than half the current producing mines lie in the Yorkshire and Midlands coalfields. They are in the oldest age group and produce 70% of the Industry's output. Some 50% of the remaining U.K. workable reserves amounting to approximately 98,000 million tons are still available to these regions. Fig. 1 Over the past two decades a gradual erosion of demand for coal in the U.K. has virtually halved the Industry's capacity. The number of Mines has reduced by 53% during the past 10 years. Productivity has increased by some 42% mainly through improvements in the central coalfields which has enabled costs to remain broadly competitive with oil.

Jan 1, 1976

By T. Wohlford

Due to the increases available base of scientific knowledge, increased independent review required by worldwide security exchanges, and the need for accuracy in characterizing mine water resources, it has become necessary to produce a more accurate hydrologic balance. This presentation provides a critical review of the steps and tools to compile a complete hydrologic review of a mine property. The forces of regulation, increased scientific analysis, better tools, and stakeholder expectations have created a perfect storm of accuracy demand. Ausenco has developed protocol to achieve the desired end.

Feb 23, 2014

By G. S. Dobby

Particle collection is considered to occur by particle collision with the bubble followed by the particle sliding over the bubble during which attachment may occur. Collision is quantified by a collision efficiency, EC. The existing model for EC is extended by including particle inertia. Attachment is quantified by an attachment efficiency, EA calculated as the fraction of particles which reside on the bubble for a time greater than the induction time. These calculations use recent data on the liquid velocity distribution over the upper half of rigid spheres. Collection efficiency, EK is given by EK = EC ? EA. Detachment is not considered. The mode is examined and shown to agree with much experimental data. For example the maximum observed in recovery vs particle size (d) can be explained as E increases with increasing d , while EA decreases. The decrease in selectivity at fine sizes is in accord with the model result that for dp < 5µm, EA ? 100% (i.e. EK ? EC) almost regardless of induction time. A decrease in bubble size does increase EK but does not improve selectivity. A high particle density (> 5g/cm3) is shown to cause a sharp peak in recovery vs size and a decreased maximum size of floatability. Finally, the possible effects of bubble and particle concentration are explored.

Jan 1, 1985

By William F. Abercrombie

The role of the laboratory is described in relation to the prospecting and exploration of kaolin clays. Test methods used to evaluate crude ore samples of kaolin clay for commercial consideration are reviewed. A background of the kaolin mineral and known means of prospecting this mineral are presented. Common analytical methods are discussed with special emphasis on those in use today.

Jan 1, 1982

By Alastair R. Biggart

ABOUT BENTONITE TUNNELLING Much has been written and many learned papers given on this subject whose generic term is Slurry Tunnelling. This paper is about the particular form of slurry tunnelling known as the Bentonite Tunnelling System. This method. of tunnelling was invented by J.V. Bartlett of consulting engineers, Mott Hay and Anderson in 1964. The general principles are incorporated in British Patent No. 1083322. It was not until the early 1970&apos;s that serious experimental work was started to prove the technical feasibility of the process. In the U.K. in 1971 Edmund Nuttall Limited started on an experimental length of 3.8m diameter tunnel at New Cross in London. In Germany at about the same time Wayss and Freytag were starting on a 3.7m diameter collector sewer tunnel in Hamburg. In Japan early slurry tunnelling work was carried out in the 1960&apos;s. In the early 1970&apos;s a large number of slurry tunnels of various diameters were carried out in that country. This paper is being presented at a time when this system of tunnelling has become an accepted method throughout the developed world. As a result of the work carried out so far there is now a large amount of data existing regarding the effects on the ground in the immediate area of the tunnel, settlement at the surface and the ability of the system to cope with ground varying from clays to coarse gravels and containing large erratics such as granite boulders. The decade of the 1970&apos;s has therefore seen a very rapid pace

Jan 1, 1979

By Hervé Le Bissonnais, Jean-Pierre Janin, Anne Bergère, Pierre Renier

"The most important impact on the environment of a tunnel excavation is the creation of surface settlements. Nowadays, the mechanized tunneling allows minimizing the settlements, applying a confinement pressure which counterbalances the ground de-confinement. It is thus essential to determine the correct amount of confinement pressure. In this paper, the authors present a 3D numerical study simulating the EPB-TBM excavation of a water tunnel, in the Flanders clays (north of France). Firstly, a simplified 3D simulation, based on the concept of instantaneous longitudinal settlement curve, was performed to predict the surface settlements for different values of heading confinement pressures. Secondly, the same pressures were tested by the EPB-TBM in a monitoring zone. The comparison between the prediction settlements and the measurements was very satisfactory and allowed validation of the numerical approach and the choice of the optimal confinement pressure value for a sensitive area of the project. INTRODUCTION The excavation of a tunnel can create displacements of the surrounding soil which may affect existing structures and generate unacceptable dysfunction. The development of the closed shield tunneling has permitted to reduce the volume loss generated around the excavation and consequently the surface settlements. In this case, as explained by different authors (Clough et al., 1985; Kastner et al., 1996; Mair and Taylor, 1997), the ground movements are influenced by the TBM works: the heading confinement pressure, the shield overcutting and conicity, the annular void grout injection parameters, the segment concrete lining rigidity, the consolidation of the grout. Hence, in the tunnel design, it is important to take into consideration these different processes of the excavation works to simulate correctly the tunneling process."

Jan 1, 2016

By S. M. Khandrika

Most of the coal presently used by the utility industry is cleaned at preparation plants employing wet processes. While water is the mainstay of coal washing, it is one of the least desirable components in the final product causing a reduction of the heating value as well as handling difficulties. Currently available dewatering techniques are inefficient for dewatering very fine coal (minus 325 mesh). The US coal industry has expressed serious concern about utilizing advanced cleaning processes such as column flotation because an efficient and economical dewatering process is not available.

Jan 1, 1992