Search Documents

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By R. C. Freas

The physical and chemical properties of mica are unique relative to most other industrial minerals. As such, mica is suitable for a variety of functional applications in new and emerging markets. This paper examines some of these applications and particularly the contribution mica makes in end product performance.

Jan 1, 1997

By N. Djordjevic

Introduction The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice -not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape. Response of structures A typical single-story building has two distinctive forms of vibration. The first form is a translatory vibration of the building superstructure (frame), and the second form is a flexural-bending vibration of the structural elements such as walls and floors (Siskind et al., 1980). Walls and floors will have several modes of oscillation. The most important is the fundamental mode of the vibration, as this mode will have the lowest frequency, the largest amplitude and will cause the largest deformations. The vibration of walls and floors is also a source of secondary vibration within a building, due to the movement of loose objects, e.g., furniture and wall fittings (Dowding, 1985). The subjective estimate of the amplitude of a vibration by the occupants of a house will be unrealistically high due to the effect of the secondary vibrations. It is now well recognized that human perception of ground vibration begins at levels that are far below those that will produce minor damage to the most fragile structures. In mining and quarrying operations, complaints regarding vibration levels tend to be determined more by human perception or annoyance rather than by observations of damage. Ground vibrations on the order of 0.08 mm/s (0.0032 ips) (Walter and Walter, 1979; Murray, 1987) can be felt, and they are often subjectively estimated to be about 100 times greater. Amplification of ground vibration in the structure depends on the amount of energy in the ground vibration spectrum that is in the vicinity of the structure's resonant frequencies together with the damping ratio of the structure at these particular frequencies. One way to avoid significant vibration amplification in a structure is to shift the dominant part of the ground vibration away from the resonant frequency range of the structure. The presented method allows for the selection of the optimum blast timing (interhole and interrow delay times) to minimize the resultant ground vibration amplitudes in a given frequency range. It also allows the selection of suboptimal, but still acceptable, blast delay times, which may be preferable from the point of view of overall blast performance. Determining frequency ranges of importance in structures In attempting to avoid amplification of vibrations in the structure, ground vibration amplitude of frequencies close to the resonant frequencies of the building needs to be minimized. The width of the frequency-minimization region is determined by the value of damping in the building. If the damping ratio is low, then the frequency-minimization region around the resonant frequency will be relatively broad. By shifting the dominant part of the ground-vibration energy into the frequency region much higher than the resonant frequency of the building (1.5 to 2 times), it is possible to achieve efficient vibration isolation of the building. In such cases, the structural dynamic amplification of ground vibration will be less than unity. The first step in this minimization process is the determination of the structural resonant frequency. From the frequency spectrum, it is possible to determine the resonant frequency of the structure. Sometimes the

Jan 1, 1998

By Alfred W. Eustes III

The first of a series on the evaluation of rock cutting tools, this paper discusses the results of full-scale laboratory drilling tests that compare the performances of several polycrystalline diamond cutter (PDC) coring bits. The tests were performed in welded tuff as part of a site characterization program. Number of cutters, size of cutters, air course design, and other parameters were evaluated as they affect penetration rate, but this paper focuses mainly on the relationships of torque vs. thrust (weight-on-bit), specific energy vs. penetration rate, and thrust vs. penetration rate. These relationships change in diagnostic ways according to bit type, bit condition, and type of welded tuff.

Jan 1, 1998

By Hemendra N. Kalia

Several attempts have been made in the past sixty or so years to commerciliaze the vast oil shale deposits of the United States of America. However, the industry has yet to become viable and economic. To date, it has not been possible to produce oil from the oil shales at a competitive price when compared to the oil produced from oilfields by conventional methods. However, the development work has been quite fruitful in furthering the art of thick bed mining and technology of in situ retorting. The in situ method has the potential of recovering oil from thick beds and the resource recovery potential is much greater than that from underground mining and surface retorting. In situ methods require that the shales/ marlstones be fragmented ' in place to induce adequate porosity and permeability to allow in situ' heating of the fragmented shales. This can be accomplished by using explosives. However, it has been found that the existing blasting systems, though very efficient, are somewhat lacking. The explosive become insensitive when shot in multiple vertical decks. They can also become insensitive when spaced horizontally at close proximity to other charges. Also, since the blasting is done in a very limited free face, this limits the delay time that can be allowed between charges. Consequently it is not always possible to predict the performance of the blasting system on a routine basis. Furthermore, since it is not possible to undertake secodary blasting, it is imperative that the blast design function properly. Recent, successful retorting by Occidental Petroleum Company of retorts seven and eight suggests that some of these problems may have been overcome. This paper addresses some aspects of in situ retorting and problems those have impeded the development of a viable oil shale industry in the U.S.A.

Jan 1, 1983

By J. P. Ducarme

The eastern U.S. contains vast reserves of thin seam coal deposits, particularly in the Appalachian mountain region. These typical 355 to 710 mm thick reserves are difficult or uneconomical to recover with present technology. The U.S. Bureau of Mines is developing technology that would allow nearly 100% recovery of thin seams in these mountaintop regions. This paper details the research that has been conducted on these new techniques and presents results of testing on a cross-ridge full-scale physical model.

Jan 1, 1994

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Jan 1, 2011

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Nov 1, 2011

By G. T. Austin

Every year the United States consumes millions of dollars worth of abrasive materials as blasting media. Entrained in either a gas or liquid stream or propelled by paddles or wheels, they are directed onto the surface of another material to modify that surface. The modifications to impacted surfaces include cleaning, cutting, deburring, etching, finishing, and peening. Blasting media can be either organic or mineral abrasive materials. Information and data presented are for only a portion of the mineral abrasives, they are; fused aluminum oxide, coal slag, copper slag, garnet, metallic shot and grit, nickel slag, olivine, silica sand, silicon carbide, and staurolite.

Jan 1, 1994

By Howard L. Hartman

Pardon my audacity, but I feel that this is the solution, not just a solution. Further, I will be so bold as to maintain that this is the last-ditch, eleventh-hour chance for the mineral industry to solve its critical technical manpower shortage. I am not being facetious. I am convinced that there is only one solution--just as there is but one real cause of the problem. My conclusion 'is reinforced by countless talks of endless hours with people both in and out of the industry, with employers and employees, and with educators and students. While I claim no originality for the idea and have no pride of authorship, I am concerned that the industry hear and heed in time. It is quite unlikely that the mineral industry and the mineral engineering profession will willingly subscribe to my thesis or gladly buy my proposal. I am convinced, however, that it is the only course of action open to us, and the only course of action which will succeed.

Jan 1, 1967

By J. Swensen, R. Brandon, A. Wallstein, S. Bessinger, J. Pile

It is generally agreed that C.C. White was the first to describe and market coal mine roof trusses beginning as early as 1967. White was issued a patent in 1969 1. Coal mine roof trusses were extensively used in the 1970’s, and their use has proven valuable in many difficult conditions. Beginning in the mid 1990’s, several types of bar/cable trusses have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, these new trusses are much easier and faster to install, thereby increasing operator safety.

Jan 1, 2004

By M. K. Larson, J. K. Whyatt

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. However, this efficiency comes at the cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impact of underlying assumptions in each method is essential to the proper use of results in mine design.

Jan 1, 2009

NICOR Mineral Ventures, Inc. retained Neyer, Tiseo and Hindo, Ltd. to evaluate the potential effects of a planned dewatering operation at NICOR's proposed, 258-acre silica sand mining facility near South Rockwood, Michigan. The ?orebody? is a horizontally extensive, friable, quartz sandstone from the Sylvania Formation which also serves as an aquifer for some of the rural, residential development near the site. We conducted an aquifer test on the site which identified the important aquifer properties. Using these data and an analytical model, we determined that the radius of influence would be expected to range up to 6000 feet from the quarry during its final development stage. An inventory of water supply wells revealed that most wells had sufficient available drawdown and would not be adversely affected. A long-term groundwater monitoring program was recommended to monitor the possible effects at some of the closest wells.

Jan 1, 1987

By T. Good

Twin roll sizers are neither compactly designed machines nor are they configured to accommodate underground mobility; in fact, twin roll sizers leave room for improvement in many aspects of the design. The DRC1200 capitalizes on the weaknesses of these machines to make a more productive, easily maintained, and compact twin roll sizer than current market offerings. These strides were made through the inception of the Hard Rock Extraction System (HRXS), which requires a mobile sizer as part of the system. After use of a third party sizer on the HRXS, potential improvements were evident. These improvements include improved structural design to reduce overall footprint and an optimized design to reduce operating cost.

Feb 23, 2014

By Daniel de la Rosa, Juan Manuel Mayoral, Damián Vital

"This paper presents a numerical study regarding the loads, and the corresponding damage, taken by the primary and secondary lining of a tunnel built in cemented fine-grained stiff soils. This study aims at establishing more rational design criteria that take into account explicity the lining performance. A 3.5 km long tunnel to be built in a densely populated northwest area of Mexico City, was considered as case study. Series of three-dimensional finite difference models, developed with FLAC3D, were used to simulate the tunnel construction, and to compute the ground settlements, internal forces, bending moments, and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams were used to study the lining performance. Several advancement lengths, and tunnel covers were considered to establish their impact on the loads transferred to the tunnel lining. A practice-oriented damage criterion for tunnels was proposed based on the interaction diagram analysis. INTRODUCTION Lining performance during conventional tunnelling, CT, as defined by the International Tunnel Association, ITA (ITA 2009) is strongly affected by the construction procedure. Special attention must be taken in cemented fine-grained materials, such as those found in the northeast portion of Mexico City, due to the potential of fragile failure (i.e. the soil fails suddenly without important deformation) that these soils may exhibit. During CT, it is assumed that the ground strength contributes to the stability of the excavation, as long as the lining is built correctly. It is common practice to consider two structures, which together form the tunnel support: 1) A primary lining, which is a flexible support, which allows excavation walls to deform to mobilize part of its shear strength, and thus contributes to the tunnel self-stability, and 2) A secondary lining. Commonly, the primary lining consists of several layers of shotcrete. In this case the installation method guarantees perfect contact between the lining and the excavation perimeter. The secondary lining, if required, is used to withstand the load conditions in the long term and also has an esthetic function. This paper presents a numerical study aimed at establishing a performance damage criterion for the primary and secondary lining design in cemented fine-grained stiff soils. Due to the lack of data, the strength and deformation parameters were established through empirically-derived relationships. Three-dimensional finite difference models were developed to simulate the tunnel construction, and compute ground settlements, internal forces, bending moments and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams, along with a damage criterion were used to study the lining performance. From the results gathered insight was gained regarding tunnel lining performance during CT."

Jan 1, 2016

By E. F. Paski

Geological materials are likely the most complex and challenging substances to quantitate by ICPOES (inductively coupled plasma optical emission spectroscopy). For complex materials having widely varying compositions, spectral overlap interferences govern detection and quantitation limits attained by ICPOES based analytical methods.

Jan 1, 1993

By S. M. Woodring

Research objectives included 1) determine relationships if any between spectral response of soil and soil textural groups, Unified Soil Classification subgroups and selected landforms and 2) develop computer assisted techniques for engineering soils mapping of remotely sensed data. The sire in northeastern Kansas, 1.6 Km by 43 Km (1.0 mi by 27 mi), contained glacial and alluvial soils. Multispectral scanner data (0.40 to 1.80 pm) collected at 915 meters altitude (3,000 feet) were analyzed using two distinct computer techniques: the nonsupervised approach involving delineation of soil training areas directly by computer and the supervised approach entailing training area selection manually by the researcher. Computer classification of surface materials follows both methods. Non supervised analysis results failed to show a consistant relation- ship between landform type and soil spectral class. Landforms correlating well displayed either unusually bright or unusually dark spectral signatures. Supervised analysis results showed a strong relationship between soil texture and soil spectral class. A moderately strong tie was shown between engineering soils groups (ML, CL, CH and OH) and their respective spectral classes, and a weak association between landform type and soil spectral class. An analysis procedure for engineering soils mapping by computer of remotely sensed data was developed. 1. Locate cultural features by visual examination of imagery. 2. Produce generalized bare soil-vegetation- water map using nonsupervised technique. 3. Outline significant soil fields for computer training using supervised approach. 4. Computer-classify entire area based on these soil fields.

Jan 1, 1974

By Missy Isaman

"Mixed ground tunnels come in all kinds. In rock tunnels with possible faults and high pressure water, the challenges are many. With the advent of Crossover TBMs, contractors can minimize machine wear in such conditions while maximizing efficiency. The newest generation of Crossover is exemplified by two projects in Albania and Turkey. A 5.56 m Crossover TBM destined for Turkey’s Gerede Water Transmission will be assembled using Onsite First Time Assembly (OFTA) from within an existing tunnel. The unique machine will bore through 30 fault zones requiring the TBM to be sealable to up to 20 bar so pre-consolidation grouting can be done. If boring under pressure is required, the TBM will bore sequentially using the screw conveyor fore and aft gates. Skewing further towards hard rock, a unique 6.2 m diameter Double Shield TBM with Crossover features was designed for Albania’s Moglicë Headrace Tunnel. The machine features closure doors and a sealing system to contain inrushes of water until they can be grouted off. This paper will discuss the unique aspects of the Crossover designs, including their inception as based on past projects in difficult ground, and their utilization at the two current projects. INTRODUCTION Specialized tunnel boring machines have been made for years to tackle specific types of ground conditions. Traditional types of TBMs bore within a specific set of ground conditions. If a project is located in a competent granite face, then a Main Beam machine is a good solution. In soft ground, Earth Pressure Balance (EPB) machines are the method of choice. Years of experience and engineering advancements have made both types of machines fast and economical solutions for tunneling. Unfortunately not all ground conditions are a perfect swath of one material, and the need for a more diverse machine is apparent."

Jan 1, 2016

By H. Shafick Hanna

The major problems are identified the high phosphorus content and the fine dissemination or encapsulation of mineral impurities, in, ,the iron bearing minerals, A process which combined extreme fine grinding techniques with magnetizing roasting or flotation separation methods, is suggested. By these methods concentrates assaying 60-61 percent Fe exceeding the widely accepted upper limit of 56 percent Fe set for these ores, were produced with 75-90 percent iron recovery. Moreover it was shown that the phosphorus content of these concentrates could be reduced from 0.25 to 0.03 percent phosphorus by acid leaching. A brief discussion on production costs based on current and future developments in iron ore processing is given.

Jan 1, 1980

By William A. Rehrig

During recent years, there have been frequent investigations on the geochemistry of biotite. This work has emphasized, and no doubt was prompted by, factors related to mineral exploration, particularly for those deposits of the porphyry copper type. A large number of papers have been devoted to the obtainment of trace-element data from plutonic biotite. These data have been used to extract primary geochemical information pertaining to the parent magna and the hydro-thermal system which together give rise to porphyry copper deposits. In two early works, Putman and Burnham (1963) and Parry and Nackowski (1963) analyzed base metal contents of ferromagnesium minerals, primarily biotite, from various barrenfmineralized plutons of the Basin and Range Province. One similar conclusion from the two studies was that the Cu, Zn, and Pb contents of magmatic biotite served as indicators of ore development within the granitic rocks genetically related to ore. This theme was then pursued vigorously by a number of authors until the present time. Results, however, have been contradictory, as reviewed by Coope (1974). For example, studies by A1 Hashimi and Brownlow (1970), Lovering et a1 (1970), Putman (1972), and Graybeal (1973) continued to support positive primary relationships between the trace-metal content (usually copper) of biotite and associated sulfide mineralization. By studying biotite in close spatial association will sulfide occurrences, Putman (1972) and Graybeal (1973) developed models for base metal partitioning in magmatic systems based on their discovery of inversely distributed copper between silicate (biotite) and sulfide phases. Conversely, research by Bradshaw (1967) and Blaxland (1971) plus the recent findings of Parry and Jacobs (1975) and Kesler et a1 (1975) found little if any evidence to support a correlation of biotite base-metal or

Jan 1, 1976