Search Documents

By Musa D. Manzi, Raymond J. Durrheim, Richard T. Masethe

Large mining-induced seismic events and their aftershocks cause hazardous working conditions, damage infrastructure, delay production and pose a risk to miners in the deep-level gold mines of South Africa. Stress changes affecting pre-existing zones of weakness are the main drivers of large mining-induced seismic events, which are often followed by aftershocks triggered by quasi-static stress transfer within the rockmass. A better understanding of seismic source mechanisms is important if the seismic data is to be used more effectively for mine planning and to reduce the rockburst risk. Four large seismic events (ML≥2.0) associated with the mining of the Ventersdorp Contact Reef (VCR) at Kloof Gold Mine occurred on 13 June 2017. The events and their fore- and aftershocks were studied in detail to establish the circumstances and the cause of the incidents. The local magnitudes ranged from ML 2.3 to ML 3.0, the seismic moment from 0.69 to 2.25 x 1013 Nm and the source radius from 92 – 150 m. The main shocks were preceded by foreshock sequences, which were especially vigorous in the four hours before the main shock. Seismicity was recorded by in-mine arrays of three-component 4.5Hz geophones (detection threshold approx. ML -2.9). Following all four main seismic events, ML 2.3, ML 2.3, ML 2.9 and ML 3.0, the network detected a total number of 300 aftershocks ranging from ML -2.9 to ML 1.6 spread within a 1300 m radius from the centre of the seismic network. The statistical properties of the aftershocks were analysed using three scaling relationships: (i) Gutenberg–Richter frequency magnitude relationship; (ii) modified Omori’s law; and (iii) Båth’s law for the magnitude of the largest aftershock. The geological or mining feature that controlled the failure (e.g., fault, dyke, pillar, abutment) was determined by calculating the orientation of the nodal planes of the large seismic events using moment tensor analysis and studying the aftershock distributions.

Apr 26, 2022

By J. Boldy

The discovery of the Delbridge massive sulphide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage halo as a litho-chemical pathfinder to blind ore, coupled to its location relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy. Systematic sampling of micro-fractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulphide deposit was subsequently found to be blind and topped at the 110 metre level.

Jan 1, 1984

Grinding and energy input in stirred media mills are studied as functions of grinding time, stirring speed, media size and density, solid concentration, impeller and tank dimensions and design, and other relevant variables. Ground product size and surface area are determined with respect to the above variables. Changes in energy input and media/pulp rheological properties during grinding are described. The best conditions for grinding limestone in the laboratory stirred media mills have been identified. Equations for correlations involving power and modified Reynolds numbers have been established.

Jan 1, 1995

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By W. C. Hirt

Selective flocculation was used to produce superclean zinc concentrate with minimized silica contamination. Research was carried out on a flotation concentrate from the Jersey Miniere Zinc Company (JMZ) in Gordonsville, Tennessee. The material was first dispersed with sodium silicate and then causticized tapioca starch was used to selectively flocculate the sphalerite, leaving the silica in suspension. This technique has been applied commercially to iron ore beneficiation but has never been used for processing zinc. The feed material assayed 0.45% Si02. Use of 0.56 kg/tonne (1.13 lb/st) of sodium silicate and 0.070 kg/tonne (0.141 lb/st) of causticized tapioca starch resulted in 98.2% zinc recovery in a purified zinc concentrate assaying 66.0% Zn and 0.24% silica. The present target level for silica contamination in JMZ zinc concentrates is 0.3% Si02. This work has shown that selective flocculation offers a potential method for cleaning flotation concentrates, particularly where low silica products are required.

Jan 1, 1993

By M. Z. Mubarok, Z. T. Ichlas, A. T. Sugiarto, K. Sukamto

The use of ozone as an oxidant for the direct leaching of zinc sulfide (sphalerite) concentrate in sulfuric acid medium under atmospheric pressure was explored. The influence of acid concentration, feed gas injection rate, particle size distribution, stirring speed, temperature and slurry density on zinc extraction efficiency was examined. The experimental results showed that the leaching efficiency depends on all of these operating parameters except for stirring speed. It was found that essentially complete dissolution of zinc from the concentrate with the present method can be achieved in only about seven hours under the conditions of sulfuric acid concentration of 2 mol/L, particle size smaller than 74 µm, slurry density of 50 g/L, stirring speed of 420 rpm and feed gas injection rate of 1 L/min at ambient temperature. The experimental results suggest that the dissolution reactions produce independent elemental sulfur that is readily floated and can be easily separated rather than forming a layer on the surface of the reacted particle, as usually observed in a system with ferric-sulfate as oxidizing agent. It was therefore determined that the dissolved ozone play a key role in improving the rate of zinc dissolution from the concentrate. Analysis of the leaching kinetics indicate that the leaching rate follows the shrinking particle model, and the overall dissolution rate of zinc is controlled by a surface reaction.

By J. M. Dean

The MANpower SUPport Program (MANSUPP), a part of the Mine Management Support System (MMSS), allows an underground coal mine site user to determine manpower requirements for production support work by considering ongoing operations and current mine conditions. The objective of MANSUPP is to plan a detailed manpower structure for a mine by incorporating a production schedule, condition-modified work standards and management preferences to predict required manhours for various activities, for example, belt moves. The program is written in Quattro Pro version 3.0 (Lotus 1-2-3 compatible) utilizing the command language, macro and formula capabilities.

Jan 1, 1992

By A. D. Wunderlich

Providing a safe & secure environment for your employees and other company assets is absolutely necessary in our litigeous society. Security hardware is no different than computers or other technical equipment, in that new equipment is developed each year that makes older equipment obsolete. This presentation will help to explain how your existing security system and security procedures can be updated to meet industry standards without the expenditure of a great deal of money. If you are concerned about potential security problems and how to address these problems, this presentation is a must.

Jan 1, 1995

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multielement ground support system, there is a need to know the support characteristics that the shotcrete contributes to the overall system. To quantify the support provided by the shotcrete, flexural strength tests were conducted with two common, commercially available fiber-reinforced shotcrete (FRS) mixes using the round determinant panel (RDP) test method, ASTM C 1550. A portable RDP test machine developed by NIOSH researchers was used to determine the peak flexural load and residual load capacity for a steel FRS and a synthetic poly FRS that were sprayed using dry mix procedures and equipment. Besides the flexural strength and loading behavior determined from these tests, a method was also developed for measuring the width of cracks exposed on the underside of a shotcrete panel during a RDP test and relating these measurements to residual load values. Quantifying the peak flexural load and residual loads of a shotcrete mix through on site testing at a mine and visually assessing the loading cycle and load-carrying capability of the shotcrete applied to underground workings will improve mine safety by providing a better assessment of the stability of shotcrete supported entries.

Jan 1, 2010

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By Anuradha Khetwal, Tala Tahernia

The estimation of TBM utilization rate can be problematic due to the uncertainty involved in the tunneling system reaction to various geology along the tunnel. Moreover, the impact of operational and management issues on TBM performance is unsettled. This includes the occurrence and duration of downtimes and the uniqueness of projects relative to the geology, machine type, backup system, site setup, crew experience, and operational restrictions imposed on the project by localities. The CSM2020 is a model based on discrete event simulation that predicts machine utilization for single or double shield TBM. This model was developed by the Earth Mechanics Institute (EMI) team, using the database of tunneling activities which was compiled based on field observation and measurements in pertinent projects. In the current study, CSM2020 was modified to simulate the workflow of slurry TBMs. The operating principle of slurry shield TBMs is different than open-mode TBMs. The model was verified by comparing results with a recently completed project in the United States. As a result, the model offers reliable utilization rate estimation in different types of TBM by implementing appropriate workflow.

Dec 1, 2022

By Terry McNulty

DOUG HALBE: I've decided that we're going to change tactics here and we're going to be nice to people from now on. [Co-chair makes gesture of intense disbelief; laughter] I've also decided who's not going to be a co-chair next year. [laughter] We thought we'd get a couple of experts for our next presentation: some people with a lot of experience. We've asked them to tell us some of the things that all of you operators out there might be able to apply immediately to your plant. Our next two speakers have a tremendous amount of experience, and I think you'll find what they're going to say is highly pertinent to most plants. I looked through their paper and found some things that I could have used in the plants I operated in the past. Our first speaker is Terry McNulty. A lot of you know Terry. He was with Anaconda for a number of years as director of research. He then was president of Hazen Research. I'm going to continue with our new custom of saying nice things. Terry is the guy that I call when I don't know something, and he's always got the answer. SPEAKER: Who do you work for, Doug? [laughter] DOUG HALBE: Remember that we're being nice to people here, Joe. I know that's a stretch. [laughter] TERRY McNULTY: Thank you, Doug. I'm a little bit mystified by this sudden switch of tactics just before I get to the podium. Doug's been a good friend for a lot of years so I guess I do have to be nice. I won't say anything deprecatory about him, but I would have to comment that the observations made by earlier speakers have been far too generous. [laughter] During nine years of consulting as a mineral processor and extractive metallurgist, I have often conducted audits of the performance of client's plants. Usually these audits have been ordered by the plant management in hopes of identifying opportunities for improving processing efficiency or reducing costs. Some of the audits, however, have been financed by the Electric Power Research Institute (EPFU) and member utilities with the objective of

Jan 1, 1998

By Tedd B. Bodimer

Why complicate an already complex machine such as a continuous miner by adding roof drills? Immediate permanent roof support is an immediate thought of the mining engineer just as elimination of frequent time-consuming places changes is a thought of the methods engineer. The realization of those two objectives has the potential for improved safety with increased production is the thought of the general manager. Miner-Bolters Used a Generation Ago These are not new thoughts as the 1CM continous miner equipped with two integral roof drills was introduced twenty-five years ago. Approximately two hundred of these machines were sold in the next five years for use in medium and high seam operations. The 1CM miner chassis that remained stationary in the center of an entry or room while the ripper bar was swung and sumped hydraulically provided an ideal platform for mounting two roof drills that could be operated during the continuous miner's production cycle. Two roof bolts could normally be installed in less time than required for the mining cycle. A typical roof drill unit is shown in Figure I.

Jan 1, 1981

By J. L. Watson

n the U.S., lead has been produced via blast furnace processing for over a century, and the slags from that pyro-metallurgical process have been accumulating on industrial sites over that extended period. Lead blast furnace slags typically contain both lead and zinc compounds in an iron-silicate matrix, and it appears highly likely that such materials will have to be processed in the near future to meet with EPA regulations. Thus it is appropriate to investigate possible processing routes to render the slags non-hazardous and simultaneously to recover metal values to partially off-set the inherent high cost of processing such materials. There are two major processing alternatives: one being pyrometallurgical and the other hydrometallurgical. The research reported here investigates leaching/solution purification/recovery processes for lead and presents experimental data for the treatment of lead blast furnace slags from S.E. Missouri. The results of the research suggest that both lead and zinc can be removed effectively from the slag, and that metallic lead can be recovered directly from the organic extractant utilized for solution purification.

Jan 1, 1995

By III Feeley

Coal is the nation's most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

The dissolution kinetics of gold in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effect of stirring speed, temperature, partial pressure of oxygen, and concentration of lixiviants on the overall leaching rate was investigated. It was found that the dissolution of gold was limited by a heterogeneous chemical reaction. The apparent activation energy was measured to be 34.7-54.3 kJ/mol under the conditions studied. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1996

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the micro- computer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user pro- grams to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to en- courage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Har- mon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the com- puterized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage ) , the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 1, 1988

By Roy A. Grancher

CYCLING WITH CEMENT "THE WHEEL IS COME FULL CIRCLE" Shakespeare's King Lear Act V, Scene 3, Line 176 The time clock of the cement industry has been turned back to the early 1950s. After the trials and tribulations of the decade of the Sixties, the hands now stand where they did just over twenty years ago. Cement shipments have steadily increased, with a record 419 million barrel level (78.8 million tons) being reached last year. Plants are operating at average utilization rates in excess of 85 percent of rated capacity. The spread between supply and demand has narrowed to where a definite shortage of cement now exists within the industry. The notable and unfortunate difference between the two periods however is that, back then, cement's returns were a respectable 14 to 18 percent, whereas today they stand at less than half those levels. Insufficient return forms the present foundation of the U.S. cement industry. This lack is destined to have a cumulative effect. Just as the industry's balance between supply and demand is returning to favorable proportions, promising a period that has historically and now should generate those profit levels required to modernize and provide for capacity addition, cement instead finds itself frozen by federal price controls into the semi-depressed condition that has existed for over a decade and from which it was just starting to emerge. Capital is not attracted to continued low returns, and increasingly restrictive pollution control measures are necessitating great non-productive expenditures be made as definite costs to stay in business. Even a clouded crystal ball would reveal that additional cement plant closings can be expected.

Jan 1, 1972

By Raymond L. Zahradnik

Marco Polo reported that the Chinese used "black rocks" for fuel, and recent studies indicate that the Chinese may have used coal in small amounts for two or three millennia previously. The use of coal as a major source of energy however, did not begin until about the twelfth century, when the inhabitants of the northeast coast of England discovered that certain black rocks found along the seashore--and thereafter known as "sea soles" would burn. Since this initial discovery, coal has been mined continuously, first in England and shortly thereafter in present Belgium, France, and Western Germany, and finally in all coal-bearing areas of the world, in ever increasing amounts. The production of coal in the United States began about 1820, when 14 tons were reportedly mined. Since that time the production of coal increased steadily until about 1907, after which the rate has fluctuated between the extremes of about 400 and 700 million tons per year. Bituminous coal and lignite production was 590 million tons in 1974. Value of production was $8. 9 billion. Anthracite production was b.3 million tons with a value of $157.5 million.

Jan 1, 1975

By M. Ziegler

The article deals with the use of a digital twin in the assessment and optimization of a conveyor system in the Chilean copper mine. This example shows that a digital twin is initially just a new (albeit powerful) tool with which the system behavior can be examined. The benefits for the customer arise through the system identification and automatic detection of critical deviations from the target state. This knowledge allows mine management to react and coordinate operational and/or maintenance counter measures to insure optimal performance of their conveyor system. The information derived from the BeltGenius digital twin also allows mine management to gain a clear perspective of the overall efficiency of their conveyors, which will be invaluable for future conveyor component selections.

Mar 2, 2022