Search Documents

By David B. Brooks

I gratefully acknowledge the help of a number of American and Canadian geologists, in both federal surveys and in private firms, who took the time to discuss this problem with me. Hans Landsberg and Bruce Netschert also followed the study with interest and encouragement. In their 1961 monograph, THE FUTURE SUPPLY OF THE MAJOR METALS, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.1/ Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vest quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.? 2/ This situation, which they called "the lead-zinc anomaly" has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative.

Jan 1, 1967

By Kenneth L. Maloney

Ten small and intermediate-sized [11 GJ/hr to 264 GJ/hr (10,000 lb/hr steam to 250,000 lb/hr steam)] coal-fired boilers in the upper Midwest have each been tested on both a bituminous eastern coal and a subbituminous western coal. The purpose of this study was to determine the feasibility of substituting western subbituminous coal for eastern bituminous coal as a means of reducing the SO x emissions from this class of boiler and to demonstrate the feasibility of greatly expanded western coal utilization as a means of reducing the use of oil and gas. The scope of this study was such that the representative boiler types were tested on both eastern and western coal for a period of time sufficient to completely characterize their individual emission and operational characteristics.

Jan 1, 1977

By Martin H. Stanczyk

The Organic Act of 1910 established the Bureau of Mines and gave it authority and responsibility for conducting research on separation, recovery, and recycling of waste products and scrap generated by the mineral and metals industries and the consuming public.(1)1 It was apparent to our Nation's leaders even then that mineral resources, once mined, are irreplaceable and that the development of methods for recycling the values contained in wastes would be required to solve the problem of even¬tual scarcity, Estimates of the increase in per capita consumption of mineral resources in this country indicate that the consumption of metals, minerals, and fossil fuels by 1980 will be double that consumed in 1970 (2). The United States can expect to meet its future mineral needs in three basic ways: the first is through increased production of primary raw minerals; second by increasing imports from foreign sources; and third by recycling secondary materials and metals that were formerly discarded as waste. Rather than consider these

Jan 1, 1972

By José Maria Silva, Eugênio Oliveira, Ruberlan Silva, Thiago Souza, Lucas Reis, Lorena Guimarães, Matheus Bianchetti

Copper mine operations consistently generate a large quantity of tailings after their concentration processing. These tailings are either piled up or stored in a dam, where both alternatives of disposal lead to environmental impacts. The dam copper tailings have a huge potential for by-product production thus improving sustainability and profitability in industrial operations. This paper describes a study aiming at producing a magnetite pellet feed as a by-product from a dam chalcopyrite flotation tailings and generating free magnetite non-magnetic rougher tailings. The chemical assay and mineralogy analysis of dam copper flotation tailings indicate low Fe grade (6.34 wt%), high SiO2 grade (63.14 wt%), low magnetite (3.6 wt%), and high iron silicates content (22.72 wt%). The complex mineralogy of these tailings leads to the need of grinding the rougher magnetite pellet feed as fine as 80% of particles smaller than 20 μm ( P80) aiming at improving magnetite liberation. The proposed process route comprises a scalping screen, low field rougher, and cleaner magnetic separations using a drum magnetic separator (80 kA/m or 1000 Gauss), followed by silicates reverse cationic flotation as a recleaner step. With this process route, it was possible to produce a high-quality magnetite pellet feed reaching 68.00 wt% of Fe, 2.13 wt% of SiO2, 0.51 wt% of Al2O3, and 95.1 wt% of magnetite. The Blaine specific surface area was 2300 cm2/ g, being in the range recommended for pelletizing (1900 up to 3000 cm2/ g). The total mass, Fe, SiO2, Al2O3, and magnetite recoveries were 2.77%, 29.71%, 0.09%, 0.12%, and 73.17%, respectively. Most of the magnetite losses, around 20% of total magnetite fed, occurred in the oversize of the scalping screen. Additionally, it generated non-magnetic rougher tailings with less than 1.0 wt% of magnetite that could be used as by-products and reduced the amount of tailings disposal in a dam. This study contributes toward the sustainability of operation, minimizing tailings disposal.

Sep 28, 2022

By M. Kuchta, S. Iverson

INTRODUCTION Underground blasting with perimeter damage control can reduce the requirement for loose rock scaling and reduce the risk of ground-fall injury. In previous work Johnson and associates (2010) from the National Institute for Occupational Safety and Health (NIOSH) developed a rock blasting perimeter damage and control design method included in the DRIFT software tool (NIOSH, 2018). This blast design software tool utilizes current methods of perimeter blasting with the added design element of a buffer row coordinated with the perimeter row to reduce perimeter damage. The coordination is in applying one of several blast damage models to calculate the damage extent for each production, buffer, and perimeter blast hole in the design. The calculated damage is then applied to the spacing between the blast holes. The basis of the buffer row design is the practical damage limit and is supported in this paper with computer models of signature blasts and full blast rounds using PFC2D (Itasca Consulting Group, Inc., 2018). Practical damage limit The practical damage radius (Rd) is not to be confused with burden. The practical damage extends toward the burden side and inward into the rock mass. For all practical purposes, the practical damage radius equals one half the burden (Hustrulid, 1999). The maximum extent of radial crack damage around a blast hole (Rcrack) and the maximum extent of radial crushing damage (Rcrush) are illustrated in Figure 1. A “practical” radius of damage (Rd) lies between the crushing limit and the cracking limit. The “practical” damage means that if the rock mass lying outside of the practical damage circle were removed, the rock remaining within the circle would easily break apart. Blast pressure and strain Work by Johnson (2010) and associates included signature blast tests in large concrete blocks. A signature blast test in concrete as exampled by strain data in Figure 2 was designed to monitor the dynamic strain at incremental distances from a single fully coupled blast hole, measure crushing and radial cracking extent by wire-sawing to expose the damage, and relate the damage to overbreak that is common in underground blasting. The initial slope or rising strain as the stress wave passes by the strain gages shows very high strain and strain rates close to the single blast hole. Since the derivative of strain versus time is strain rate, a line tangent to each of the strain curves at the maximum strain rate is drawn and the strain rates identified. The high strain rates were then plotted on a semi-log in Figure 3 to show a linear trend. The strain rate is greater than 100 s-1 within 20 cm from the blast hole for the signature blast experiment. The strain rate at the blast hole wall is projected to be 300 s-1. Figure 4 illustrates the damage in the NIOSH block exposed by a wire saw cut.

Jan 1, 2019

By Richard Collins

The projected depletion and the increasing costs of petroleum and natural gas along with the public and governmental resistance to nuclear energy have caused coal to emerge as one of today's answers to both our short term and long term energy needs in power generation. In order to satisfy this need, major increases in coal production are mandatory, thus requiring more and higher capacity coal transfer terminals. The logic for selecting coal as the major fuel for power generation is based on many different reports on the existing and potential energy sources, which include petroleum, natural gas, hydropower, solar, geothermal, and nuclear. The following is a brief synopsis of these reports for each type of energy.

Jan 1, 1978

By İbrahim Gunes, ATILA GURHAN CELIK, Eren Komurlu

This study introduces a new apparatus designed to improve the load-bearing capacities and insertion efficiency of split set type friction bolts. Laboratory and site studies demonstrated the apparatus’s advantages in terms of practicality and prevention of buckling. The apparatus temporarily compresses the split tubes, reducing friction during insertion and increasing normal stresses and friction capacity at the bolt-rock contacts.

Jan 3, 2022

By Thomas W. Smelser

A full-scale geotechnical model of a 15-foot (4.6 m) wide coal mine entry in correlation with computer finite-element analysis (FEA) is being employed at the Bureau of Mines Spokane Research Center for basic research on roof-bolt support systems. Physical and computer modeling of various coal mine roof-bolt reinforcement systems will increase our basic knowledge of how roof supports function. This information, in correlation with computer FEA and underground verification tests, will provide a basis for establishing safer, more cost- effective roof control plans and help establish guidelines for employing fully grouted and conventional bolting systems. The basic rationale for the research, research approach, methods and equipment employed, results to date, and future research plans are described in this paper.

Jan 1, 1982

By W. D. Hausel

The Wyoming Province is an Archean craton which underlies portions of Idaho, Montana, Nevada, Utah, and much of Wyoming. The cratonic block consists of Archean age granite-gneiss with interspersed greenstone belts and related supracrustal terranes exposed in the cores of several Laramide uplifts. Resources found in the Province and in the adjacent accreted Proterozoic terrane include banded iron formation, Au, Pt, Pd, W, Sn, Cr, Ni, Zn, Cu, and diamonds. The Province shows many similarities to the mineral-rich cratons of the Canadian shield, the Rhodesian and Transvaal cratons of southern Africa, and the Pilbara and Yilgarn blocks of Western Australia, where much of the world's precious and strategic metal and gemstone resources are located.

Jan 1, 1991

By L. Thompsen

High pressure grinding has been introduced into many grinding applications. The high pressure grinding roll offers capacity increases of existing plants and savings in operating costs. Also metallurgical advantages could be achieved. The first high pressure grinding roll in a copper mine was commissioned in Arizona in July 1995. This paper provides information about the operating experience gathered during the first months of operation. The current flowsheet will be described as well as further options for plant arrangements.

Jan 1, 1996

By E. Molleman

This paper reports on testwork exploring the dissolution/reprecipitation reaction: ZnS + 2HCl ? ZnCl2 + H2S, as part of a process for the production of pure ZnS. In spheroidal form, this would constitute a premium fonn of zinc refinery roaster feed enabling the production of pure ZnO. The research focused on the influence of proton activity on dissolution of zinc concentrates from Brunswick Mining & Smelting, Red Dog and Tara. The results and thermodynamic data suggest that the three concentrates contained significant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1997

By James O. Glanville

Ice frozen from a dilute chemical solution is mechanically weaker than ice frozen from pure water. This phenomenon is the basis of a practical method for reducing the strength of a mass of frozen coal. If a chemical additive is applied to moist coal, prior to its shipment during freezing weather, the resulting frozen coal can be more easily broken than in the absence of the chemical additive. This greatly expedites the unloading and handling of coal during winter. There has been considerable research into the nature and mechanical strength of ice frozen from various solutions. The literature relating to this process has been reviewed as has the literature relating to the chemical treatment of coal and mineral particulates. Some important articles are discussed and speculations are made about the nature of the ice-weakening process. A laboratory evaluation of the effects of chemical additives on the mechanical strength of ice and frozen coal has been made. An apparatus designed for this purpose is described, and some results obtained with it are discussed.

Jan 1, 1980

By Yassine Lahmadi, Edoardo Trivellato, Christian Chereau, Bénédicte Robert

Within the framework of the adaptation of the South-East European Technicentre (Technicentre Sud-Est Européen TSEE), SNCF Voyageurs appointed Pini with the project management mission (MOE) for the design and construction monitoring of a road tunnel. This investment has a dual function: during the site transformation phase, it facilitates the work logistics (and shorten traffic flows); and in the operating phase, it is intended to ease all movements on the site over the long term. This is a limited-length gallery (50 meters) to be performed in conventional excavation below Poniatowski Avenue (Paris 12e). The excavation, crossing the entire width of the boulevard, constitutes a major challenge, given the very low coverage (less than 5.5 m), and the surrounding main infrastructures. The same project mis- sion includes the design of the tunnel accesses, via reinforced-concrete frame structures. The targeted design questions several aspects of its execution framework, and particularly, continuous operation must be guaranteed to the neighboring networks during the works. The installation of an umbrella- pipe all along the excavation profile, the progression in divided sub-sections, and the implementation of a complex monitoring system are hence key elements for limiting and controlling any deformation. An exhaustive 3D finite element modelling was performed, taking into account the detailed phasing of construction (pre-support, excavation in divided section, preliminary support and definitive lining), to dimen- sion the structures, and, overall, to analyze the impacts on the neighboring structures and facilities. During the execution phase (planned for mid-2024), monitoring activities with back-analyses as close as possible to the works are planned.

Jun 23, 2024

By Jian Wang, Xiaoming Sun, Ming Jiang, Fuxin Shen, Chengyu Miao, Wenchao Zhao, Yong Zhang

The increased thickness of the coal seam leads to higher goaf roof collapse height. In contrast, the dynamic pressure from the mining of ultra-thick coal seams generates higher abutment pressures around the mined area and may affect the stability of roadways servicing these panels. To mitigate the deformation and damage issues in the roadways during the extraction of ultra-thick coal seams under a high depth of cover, researchers have proposed combining high prestress constant resistance support and roof-cutting technology (HPCR-RC). The deformation and failure mechanisms of the roadways during the extraction of ultra-thick coal seams under a high depth of cover, along with the mechanisms and field control effects of the combined support system, have been analyzed through theoretical analysis, numerical simulation, and field experiments. The research findings reveal that the high in situ stress, initial excavation disturbance, rotation, and subsidence of the fractured roof of the extra-thick coal seam led to significant deformation and damage in the roadways. High prestress constant resistance support compensates for the initial stress loss, reduces initial stress concentration, and absorbs deformation energy. Moreover, the roof-cutting technology severs the connection between the goaf roof and the roadway roof, disrupts the path of stress transfer, raises the level of roof backfilling in the goaf, and provides support to the roof, effectively alleviating the pressure on the coal pillar ahead and adjacent to the working face. Field experiments have confirmed the effectiveness of HPCR-RC, as indicated by a substantial decrease in surrounding rock deformation and support pressure within the roadways.

Sep 25, 2023

By R. P. Schneider

The Chino mine, concentrator, and smelter are located in Grant County in Southwestern New Mexico. Chino Mines Company is a partnership two-thirds owned and operated by Kennecott Santa Fe Corp., and one-third owned by MC Minerals Corp. (Mitsubishi) of Japan. The Chino Ore Body The Chino ore body is a widely varied deposit of rock types and contains intrusive stocks and sediments. The stocks contain chalcocite in a matrix of quartz, mica, and feldspar. Much of the feldspar is altered to clay. Some of these stocks are enriched with native copper. The sediments contain chalcopyrite associated with gangue minerals including magnetite, pyrite, garnet chlorite, and epidote. The contact of the stock and sediment is heavily altered to chlorite and clay. The stock ores contain economic quantities of molybdenite. The operating work index of Chino ore varies from 5 to 20 kwh/ton and averages 8.5 kwh/ton. The ore head to the concentrator averaged 0.81% copper and 0.010% molybdenum. Fifteen percent of the total copper head exists as nonsulfide mineralization.

Jan 1, 1985

By M. K. Larson

"Specialized numerical modeling codes have been developed over the years to estimate ground stresses during the excavation of coal in underground mines. One of these tools, MULSIM, a displacement discontinuity boundary element code, was last developed by Zipf into a version called MULSIM/NL [USBM 1992a, 1992b]. The code was used frequently in years past, but closure of the Bureau of Mines in 1996 marked the beginning of a pause in its development. A similar tool with distinctly different treatment of overburden idealization, LaModel, was subsequently developed [Heasley 1997] and largely displaced MULSIM/NL in the literature. However, recent work modeling deep western longwall coal mines [Larson and Whyatt 2013] has demonstrated that MULSIM has distinct advantages for regions with relatively stiff and strong overburden. This work required that MULSIM be revived and updated into a version called MulsimNL/Large. Updates include larger array sizes, greater precision, greater number of materials, and the addition of a five-point, six-segment pillar load/displacement model that provides the user a more flexible coal-strength model allowing hardening and softening before a final residual strength. MulsimNL/Large has the ability to calibrate to large load transfer distances observed in some western U.S. coal mines that appear to be caused by strong, massive units in the overburden and/or floor of a coal mine. Also, it provides the ability to calibrate gob stiffness to simulate measurements or estimates of overpanel weight distribution between gob and abutment, while still maintaining load transfer distance with minor adjustments. MulsimNL/Large can easily implement material strengths calculated from various pillar strength models. The five-point model gives MulsimNL/Large the ability to easily simulate pillar behavior that is extracted from detailed pillar models, such as FLAC3D. MulsimNL/Large or similar approaches should be considered for evaluating mining layouts where stratigraphic conditions are known to cause overpanel weight to transfer to an extent significantly longer than the empirical method widely used to calculate load transfer distances in the U.S. [Peng and Chiang 1984; Mark 1987; USBM 1990]."

Jan 1, 2015

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

As indoor positioning provides particular challenges due to the unavailability of GPS signals, various systems such as ultrawideband (UWB), radio frequency identification (RFID), ultrasound, and wireless local area network (WLAN) have been proposed in recent years. Some of these technologies are currently being marketed and some are still being developed. UWB technology allows for higher precision while also reducing power consumption. Hence, the underground automation and localization systems can use this technology for more accuracy and robustness. This article discusses new robust UWB modules used for underground positioning and collision avoidance with regard to human safety in underground mining operations.

Jul 31, 2020

By James J. Olson

Most of the projects summarized in this paper are funded under the Bureau's Advancing Metal-Nonmetal Mining Technology program and are part of the in situ mining subprogram coordinated at the Twin Cities Mining Research Center. The borehole mining equipment development, are funded under the Bureau's Advancing Coal Mining Technology program, is essential to accelerated progress in the in situ mining subprogram, and some background information on this concept is included. The initial in situ research projects started in 1971-72 evaluated some of the critical blast design parameters for in situ copper leaching. The present program totals about $1 million per year and includes in-house research projects, cooperative (cost-sharing) projects with the mining industry, and research and development contracts. Two different extraction schemes are under investigation: inplace leaching and borehole (or slurry) mining. The principal commodity targets for the Bureau's improved in situ mining technologies include copper, uranium, coal, and potash. The principal purpose of this paper is to inform the mining industry of the in situ mining research recently completed or being conducted by the Bureau of Mines. In addition the Bureau encourages companies to comment on the program accomplishments as well as offer suggestions on top priority research needs for improving the in situ mining methods described in this paper.

Jan 1, 1977

By M. D. Scott

Lornex Mining Corporation operates an open pit porphyry copper mine in the Highland Valley southwest of Kamloops with a rated capacity of 43 500 TPD (48,000 TPD). It went into production in April 1972. Its concentrator consists of two grinding and flotation circuits in parallel each composed of a 6 000 KW (8,000 HP) 9,75 m (32 foot) diameter by 4,724 m (15'-6") semi-autogenous primary mill feeding two 3 000 KW (4,000 HP) 5,029 m (16.5 foot) diameter by 7,01 m (23 foot) secondary ball mills each feeding a bank of flotation cells. ,The original tailings system picked up the tailings from the flota¬tion circuits in a concrete collection box in the mill and carried the 36% solids density by weight slurry 488 m (1,600LF) through a 1100 mm (42 inch) diameter wood stave pipeline on a .46 percent slope to three 99,06 m (325 foot) diameter center drive thickeners. From the collection box under the thickeners the tailings line con¬sisted of three sections, carrying 50% solids density slurry. The first section consisted of 1460 m (4,800 LF) of 910 mm (36 inch) asbestos cement pipe for gravity flow from the thickener under flow elevation of 1252,4 m (4,109 feet) to the first pump station at elevation 1207,6 m (3,962 feet). Eight concrete drop boxes were used to limit the maximum slope on the pipeline to 0.5 percent.

Jan 1, 1976

By Taeyong Lee, Cole Bales, Matt Fowler, John Horne

Mitchell Point Tunnel near Hood River, Oregon is one of the more unique segments of the Historic Columbia River Highway and State Trail being constructed through the Columbia River Gorge. This 650-foot bike/pedestrian tunnel set to open in 2024 is being delivered by FHWA in partnership with Oregon DOT, Oregon State Parks, and the U.S. Forest Service. Primarily driven using drill & blast excavation methods through basalt, the shotcrete and dowel-supported tunnel features masonry portals and ve window adits that provide illumination and views of the river similar to the original highway tunnel of many vistas built in 1915 that was removed in 1966 to make way for Interstate 84. This paper summarizes the planning, design, and construction.

Jun 23, 2024