Search Documents

By M. Moats

Copper electrowinning operations have dramatically improved their ability to produce high quality copper at low costs over the past several decades. Even so, some fundamental knowledge is still lacking that could allow operations to run even more efficiently. For example, a rule of thumb exists that estimates a current efficiency loss of 2-3% per gram per liter of iron in the electrolyte. While several laboratory studies have been performed that demonstrate this rule of thumb is likely true, no definitive relationship exists. In this paper, the first steps in developing a definitive relationship are presented. The effective diffusivity of ferric ions in synthetic copper electrowinning solutions was measured using chronoamperometry and the Cottrell equation. The effective diffusivity of ferric ion was determined as a function of electrolyte concentration and temperature. Synthetic electrolytes were then used in laboratory-scaled copper electrowinning experiments, where relationships between current efficiency and solution composition were found to exist under stagnant conditions. Key words: Copper electrowinning, Current efficiency, Chronoamperometry, Ferric ions

Jan 1, 2009

By Jonathan G. Price

Silver-copper-lead deposlts in Precambrian, Permian, and Cretaceous red-bed sequences near Van Horn, Texas, have the following features In common: (1) mineralization controlled by steeply dipping fractures in sandstones, (2) lack of ore In overlying and interbedded limestones, (3) absence of igneous intrusions, (4) sulfide ores without typical hydrothermal gangue minerals, and (5) associated arsenic, molybdenum, zinc, and cadmium but not gold. Ore was probably deposited along fractures by reaction between low-temperature, oxidizing, metal-rich ground waters and sulfide-bearing waters or rocks. Detailed mapping and studies of fracture patterns indicate that mineralization occurred during Basin and Range extensional deformation, thereby postdating major Trans-Pecos igneous activity.

Jan 1, 1983

By A. Hajati

The main purpose of this study was to find the optimum values for factors affecting the Zn recovery rate using oxine or dithizone as a chelating agent collector during flotation in a Hallimond tube. Eight control factors, including four levels of pH, oxine/dithizone, corn starch, sodium thiosulfate, sodium citrate, sodium silicate, conditioning and floating durations were considered in a Taguchi experimental design technique. An L32 orthogonal array was applied to determine the signal-to-noise (S/N) ratio. Analysis of variance (ANOVA) was used to determine the optimum conditions and the most significant parameters affecting the reaction rate. Analysis of the experiments using the Taguchi approach indicated that pH had the highest contribution to the recovery rate of zinc oxide particles. The results showed that the recovery rate of zinc increased by 43.4 ± 3.0% and 24.9 ± 3.2% using oxine and dithizone, respectively, under optimum conditions with a confidence level of 90%.

Jan 1, 2010

By J. S. McEwan

This paper describes the derivation of a set of simultaneous algebraic equations that can be solved to produce a rigorous theoretical mass balance around solution mining wells. This mass balance can then be compared with a mass balance calculated from field measurements to provide the percentage of mass balance closure. Significant deviations from the closure can be an indication that the wells are either gaining or losing circulation fluids. The equations also provide calculations for the amount of water and dissolved mineral that accumulates in the well during the mining process, as well as the net mining rate. Equations for both single mineral mining and multiple mineral mining are discussed. They can easily be formatted into spread sheets for rapid calculation of field measurement data.

Jan 1, 2010

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, Mari Lundström, Eero Kolehmainen

With decreasing ore grades, the tailings of mining operations are becoming of increasing interest as metal-containing secondary raw materials. The objective of the current work was to investigate chloride leaching of gold, copper, cobalt, nickel, and zinc present in the flotation tailings. In the current study, the effect of cupric ion as an oxidant (0–50 g/L) and NaCl (150–250 g/L) on metals extraction was investigated. The other parameters, such as pH (1.8), temperature (95 °C), solid/liquid ratio (25%), oxygen feed rate (1200 mL/min), leaching time (24 h), and stirring rate (950 rpm), were kept constant. Gold dissolution rate was shown to increase with increase in cupric ion concentrations up to 50 g/L. Also, increase in NaCl concentration up to 250 g/L increased gold extraction. Majority of the copper present in the flotation tailings could be dissolved with all the all solutions investigated. The other base metals, cobalt, nickel, and zinc extractions were also shown to increase with increase in the cupric ion and sodium chloride concentration. However, even in the absence of cupric ion addition (t = 72 h, 250 g/L NaCl), the final extraction of Cu, Ni, Zn, Co, and Fe increased up to 98, 93, 83, 76, and 80%, respectively. This shows the power of inherently originating oxidants present in the tailings. Furthermore, the solid analysis of the leach residue indicated that leaching the flotation tailings in pure NaCl may result in partial gold dissolution. The results demonstrate that significant amount of metals present in the tailings could be extracted even with only NaCl as added chemical in the presence of oxygen feed, oxidizing agents originating directly from the raw material. This can provide an advantageous cyanide-free method for extraction of metals from very low-grade tailings with low chemical consumption.

By Jian Wang, Kun Li, Hao Wu, Juan Nan

In this paper, in order to solve the problems of low accuracy and slow speed of fire flame recognition, an extreme learning machine (ELM) method based on improved Harris hawks optimization (IHHO) is proposed for fire flame recognition. A novel Harris hawks optimization (HHO) is used to solve the problem of parameter selection of ELM. In order to solve the problem that the original HHO is prone to fall into local optimum, firstly circle mapping is used to initialize the population to solve the problem of uneven distribution and small range of the initial population. Then the formula of escaping energy of HHO is modified to make the population have a large range in the middle and late iterations while gradually decreasing in the whole iteration process. Thus, the exploitation stage in HHO is improved to make the search range smaller near the optimal solution to accelerate the convergence process. Finally, at the end of each iteration, a certain number of individuals are selected to perform Gaussian and Cauchy hybrid mutation to prevent the IHHO from falling into local optimization. Through three groups of experiments, the effectiveness of the proposed IHHO and IHHO-ELM is verified. In experiment 1, the convergence performance of IHHO is significantly better than that of the other remaining algorithms in the test results of six benchmark functions. In experiments 2 and 3 of real fire flame recognition case, IHHO-ELM outperforms other remaining algorithms on the whole and has significant advantages in some indexes.

Jan 17, 2023

By Muhammad Kamran, NIAZ MUHAMMAD SHAHANI

This study elucidates a new idea to predict mine fire levels by employing several machine learning techniques. A total of 120 patterns of various mine fire influencing parameters, such as oxygen, nitrogen, carbon monoxide, and temperature, were compiled from the Adularya coal mine in Turkey. Techniques like t-distributed stochastic neighbor embedding (t-SNE) and k-means clustering were used to process the data, and support vector classification (SVC) was executed to predict various levels of the mine fire. The results revealed that the proposed model has higher credibility to predict the various levels of underground mine fires.

Feb 14, 2022

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification such as nickel (Ni), cobalt (Co), copper (Cu) and manganese (Mn) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte; ammoniacal leaching (gas reduction or Cuprion); and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered the pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stem from the 1970s and 1980s, and are not always easily accessible. This article details the series of tests conducted and provides updated results obtained — high Ni/Co/Cu recovery with limited manganese/iron (Mn/Fe) — as well as comments on the potential treatment options on the product solution and residue.

Sep 1, 2025

By George Innes

The soda ash business in the United States has undergone a sweeping technological change in ihe last 20 years. In a world where synthetics are continuzlly replacing natural products, here we have exactly the opposite, a syntheric chemical being replaced by a natural product. This change is nearly complete in the U.S. and is beginning to take place in Europe and other parts of the world.

Jan 1, 1980

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Laramide porphyry copper deposits are large, low grade (<0.8% Cu) deposits that contain disseminated copper minerals, breccias, and stockwork veinlets of copper and molybdenum sulfides associated with porphyritic intrusions in Southwestern New Mexico. Critical minerals, such as PGEs, tellurium, indium, germanium, and gallium are recovered from the anode slimes remaining after copper is refined. Detailed age dating, mineralogy, geochemistry, along with geologic mapping could refine the location of critical minerals within specific systems and could identify porphyry systems with elevated critical minerals that could become economic, in addition to the already produced copper, gold and molybdenum.

Feb 1, 2023

By Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducrng bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the porosities of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900&apos;s to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also extended a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore modes. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of the first of June 1984, a total of 29.4 million long tons of sulphur had been produced west of the Pecos -aver. Duval produced more than 88 percent of that total.

Jan 1, 1984

By M. Karmis

The design of coal-mine layouts is based on the knowledge of a broad range of geological and geotechnical parameters, which must be determined from a sequence of exploration programs. It follows that any weaknesses in selecting, determining, interpreting or utilizing these data are inevitably reflected into the mine-planning process. In this paper, the main methods of exploration are reviewed and evaluated with the emphasis on acquisition, interpretation and storage of variables pertaining to mine-design. Some common problems are highlighted and recommendations are given for improving the utilization of data and optimizing coal-mine design procedures.

Jan 1, 1980

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983

By Saurabh Kundu, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Manikanta Nallamilli, Shaik Mahaboob Basha, Neha Gupta, Srinivas Dwarapudi, Dhiraj Madhukar Kadhe

Iron ore pelletizing using compressive and shear action on wet mixture feed has been studied. The physical properties, namely, moisture content, drop strength, green compressive strength (GCS), dry compressive strength (DCS), porosity, and cold crushing strength (CCS), have been studied. Pelletizing tests were carried out on four different types of ore, namely, hematite ore, magnetite ore, goethite ore, and sinter return fines. The inference of shear forces on silica distribution index in dry pellet has been studied using optical and scanning electron microscopy. Significant improvement in physical strength was observed due to compressive and shear forces on the pellet mixture feed. However, decrease in moisture content and ball porosity has been observed. Silica distribution index improved by 1.72 times for hematite ore, 1.47 times for magnetite ore, and 1.68 times for goethite ore. It has been found that bubble cavity has been reduced which is good indicator in terms of physical properties.

Jan 29, 2022

By J. D. Vincent

The Mission By-Products Plant at the Mission Concentrator of the American Smelting and Refining Company, some 20 miles south of Tucson, Arizona in the Twin Buttes mining area, has been in operation slightly over a year. The plant produces a molybdenite concentrate a copper concentrate and, at times, a zinc concentrate. An intensive test program of over three years was conducted at Mission to make the recovery of molybdenum economic. Briefly it was found necessary to make a scavenger concentrate in the copper mill before it was possible to recover economic quantities of molybdenite. By so doing there were resulting additional recoveries of copper, silver and zinc. This program resulted in the design and construction of the existing plant. A paper by the authors discussing the test work and the design was presented at the, October 1965 meeting of the American Mining Congress in Las Vegas, Nevada, by Mr. Wayne Bossard.

Jan 1, 1966

By Rakesh Sehgal, Pushkar Verma, Mohit Sharma

"SJVN Limited successfully commissioned its Rampur HEP (412 MW) in 2014. The project has been planned to operate in tandem by directly utilizing the Tail Water of SJVN’s prestigious Nathpa Jhakri Hydro Power Station 1500 MW located upstream. The initial filling of voluminous water conductor system of RHEP with 10.50 m diameter, 15 Kilometer long Head Race Tunnel, involved more than 1.5 million m3 of water. The filling operation of such a large diameter tunnel constructed in young folded Himalayas which always offer less ideal sites for tunnelling and their subsequent operations under pressurized conditions is worth sharing with tunnelling fraternity. The paper covers meticulous planning, execution, precautions taken, and performance monitoring during filling process keeping in view the fragile geology, low rock cover zones, shear zones in close vicinity of thickly inhabited areas, squeezing zones, hot water zones encountered during excavation.1.0 RAMPUR HYDRO POWER STATION IN BRIEFRampur Hydroelectric Project (412 MW), is located in Himachal Pradesh (India). This project is a downstream development of Nathpa Jhakri Hydro Power Station (1500 MW) constructed on river Satluj and commissioned during 2003. Both the projects today are now successfully working in tandem. The upstream NJHPS has been constructed on the left bank of the river while the downstream Rampur HPS is located on right bank of the river (Figure-1).The major length of HRT of Rampur project lies on right bank of river before it crosses under the river in its initial reach (Figure-2). The main features of the project are as below:• 10.50 m diameter 15 km long HRT ending in a 155.75 m deep, 38.00 m diameter surge shaft.• 3 steel lined pressure shafts, 5.4 m dia, 211-220m long.• Surface valve house 69 m long x 10.50 m wide x 23 m high housing 3 No. butterfly valves• 3 No. surface penstocks 5.4m dia 368-382m long, bifurcating into six penstocks, each of 3.80 mdia. to feed six generating units of surface power house 158 m long x 24.50 m wide x 48 m high, with Francis turbines each of 68.67 MW capacity."

Jan 1, 2016

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification (nickel, cobalt, copper, and manganese) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte, ammoniacal leaching (gas reduction or Cuprion), and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stems from the 1970s and 1980s and is not always easily accessible. This paper will detail the series of tests conducted and provide updated results obtained (high Ni/Co/Cu recovery with limited Mn/Fe), as well as comment on the potential treatment options on the product solution and residue.

Feb 1, 2025

By W. K. Choi

Using electrochemical techniques it was demonstrated that bioleaching of gold from refractory pyritic ores is a complex phenomenon. Many intermediate electrochemical reactions were found to be involved in the oxidation of pyrite, using cyclic voltammetry and carbon paste-pyrite containing electrode. Furthermore, the oxidation process was controlled by solid-state diffusion as suggested by chronoamperometric and chronopotentiometric measurements. Using the Sand&apos;s approach, the activation energy of solid-state diffusion was found to be = 22.4 kJ. After bioleaching, 96% gold was extracted from the leach resi¬due with a thiourea solution in 1 hour. A generalized model for the mechanism of pyrite oxidation has been presented.

Jan 1, 1990

By Myles E. Robinson

During the last decade there were pronounced changes in the competitive pattern of the fossill fuels It is proposed to trace these trends and describe inter-fuel competition, first as it relates to the economy as a whole and then more specifically to examine competition of the fossil fuels as these share the electric utility market. Table 1, Competitive Fuels and Water Power Used in the United States, 1950-1959, shows the growth in the consumption of coal, oil, gas and water power &apos;during the past decade. Uses which are not directly competitive among the fuels, such as tractor fuel, carbon black, and consumption of petroleum products in the making of synthetic rubber, have been excluded from these statistics. The experience of the three fossil fuels in competition since 1950 shows natural gas expanding more rapidly, than oil by roughly twice as much, 219.0 percent&apos; compared to 124.1 percent growth in B.t.u.s of oil consumed in the ten-year period. Percentagewise, water power little more than held its own, and coal, including anthracite, actually decreased more than one-fifth.

Jan 1, 1961

By K. A. Perry, R. Q. Eades

The University of Kentucky conducted inerting tests and angle of ejection tests on three types of rock dust. A newly developed hydrophobic dust was compared against typical dry and wet dust applications. This new product is designed to alleviate respirable dust concerns for dry dusting and caking issues with wet dusting. Samples for both test types were prepared in a laboratory and subjected to temperature and humidity cycles that are typical of an underground coal mine. Inerting tests were conducted in a 38-L chamber with a 5-kJ Sobbe igniter. Angle of ejection testing was conducted at the University of Kentucky Explosives Research Team’s laboratory in Georgetown, KY. The results of these tests indicate that the newly developed dust has improved results for flame suppression and ejection compared with typical wet dust applications. The significance of these results is discussed with regard to existing respirable dust regulations and the issues associated with caking.

Jan 1, 2016